TYPE CERTIFICATE DATA SHEET Nº EA-9810

(26 754 lb); linear variation from 33.0% MAC at 12 136 kg (26 754 lb) to 34.42% MAC at 11 657 kg (25 700 lb); linear variation from 34.42% MAC at 11 657 kg (25 700 lb) to 35.00% MAC at 11 462 kg (25 269 lb); 35.00% MAC at 11 462 kg (25 269 lb) to 9 666 kg (21 310 lb). CESSNA 10 October 2011 EA-9810-02 Sheet 4/9 C. G. RANGE (Cont.) (2) Forward Limits - For airplane serial numbers 750-0001 through 750-0172 not incorporating Cessna Service Bulletin SB 750-71-10: linear variation from 15.84% MAC at 16 194 kg (35 700 lb) to 15.00% MAC from 15 922 kg (35 100 lb); 15.00% MAC from 15 922 kg (35 100 lb) to 14 742 kg (32 500 lb); linear variation from 15.00% MAC at 14 742 kg (32 500 lb) to 21.00% MAC 13 381 kg (29 500 lb); 21.00% MAC at 13 381kg (29 500 lb) to 12 701 kg (28 000 lb); linear variation from 21.00% MAC at 12 701 kg (28 000 lb) to 26.16% MAC at 10 149 kg (22 374 lb); linear variation from 26.16% MAC at 10 149 kg (22 374 lb) to 35.00% MAC at 9 666 kg (21 310 lb). - For airplane serial numbers 750-0173 and on and aircraft incorporating Cessna Service Bulletin SB 750-71-10: linear variation from 16.40% MAC at 16 375 kg (36 100 lb) to 15.00% MAC at 15 922 kg (35 100 lb) to 14 742 kg (32 500 lb); linear variation from 15.00% MAC at 14 742 kg (32 500 lb) to 21.00% MAC at 13 381 kg (29 500 lb); to 12 701 kg (28 000 lb); linear variation from 21.00% MAC at 12 701 kg (28 000 lb) to 26.16% MAC at 10 149 kg (22 374 lb); linear variation from 26.16% MAC at 10 149 kg (22 374 lb) to 35.00% MAC at 9 666 kg (21 310 lb). EMPTY WEIGHT C. G. RANGE None DATUM Zero reference datum is 468.6 cm (184,5 in) forward of the leveling screw located 6.35 cm (2.50 in) forward of the cabin door frame on Water Line 127.25. LEVELING MEANS Outboard floor panel inside of door parallel to B. L. 13.00 MEAN AERODYNAMIC CHORD 301.2 cm (118.6 in) - L. E. of MAC at F. S. 387.60 MAXIMUM WEIGHT For airplane serial numbers 750-0001 through 750-0172 not incorporating Cessna Service Bulletin SB 750-71-10, and not incorporating Cessna Service Bulletin SB750-32-50: Takeoff: 16 194 kg (35 700 lb) Landing: 14 425 kg (31 800 lb) Zero Fuel: 11 068 kg (24 400 lb) Ramp: 16 330 kg (36 000 lb) For airplane serial numbers 750-0173 and on and aircraft incorporating Cessna Service Bulletin SB 750-71-10, or aircraft incorporating Cessna Service Bulletin SB750-32-50: Takeoff: 16 375 kg (36 100 lb) Landing: 14 425 kg (31 800 lb) Zero Fuel: 11 068 kg (24 400 lb) Ramp: 16 511 kg (36 400 lb) MINIMUM CREW For all flights: 2 persons (pilot and co-pilot). MAXIMUM PASSENGERS 12 passengers maximum. MAXIMUM BAGGAGE Tail compartment 318 kg (700 lb) at F .S. 490.0 CESSNA 10 October 2011 EA-9810-02 Sheet 5/9 Floor loading density: 828.8 kg per square meter (170 lb per square foot) FUEL CAPACITY Two wing tanks: usable 1 972 liters (521 US Gal) each tank; arm 1 041.6 cm (410.07 in). Center tank: usable 3361 liters (888 US Gal) usable each tank; 851.7 cm (335.32 in). See Note 1: for data on unusable fuel. OIL CAPACITY Two engine-mounted tanks: total 11.5 liters (12.1 qts) each; (usable) 11.2 liters. (11.8 qts) each; arm 1 383 cm (544.30 in). See Note 1 for data on unusable oil. MAXIMUM OPERATING ALTITUDE 15,545 m (51,000 ft) CONTROL SURFACE MOVEMENTS To insure proper operation of the airplane, the movement of the various control surfaces must be carefully controlled by proper rigging of the flight control systems. The airplane must, therefore, be rigged in accordance with the appropriate FAA approved rigging specification or Cessna drawing. Specific rigging instructions may also be found in the Model 750 Maintenance Manual (Instructions for Continued Airworthiness), part number 75MM00 (or later approved revision). Stabilizer: Range of Stabilizer Setting (Leading Edge Position) Cessna Drawing nr. 6700750 Primary Trim Max. L.E. Up 1.2  0.3 Max. L.E. Down -12  0.6 Secondary Trim Max. L.E. Up 1.2  0.3 Max. L.E. Down -12  0.6 Elevator: Rigging Spec. Nr. 6760405 Up 18.5 + 0.5/-0 Down 14.0  1 Rudder: Rigging Spec. Nr. 6760405 Lower (perpendicular to H. L.) Right 29.5  0.5 Left 29.5  0.5 Upper (perpendicular H. L.) Right 17 + 1.5 /-1.0 Left 17 + 1.5 /-1.0 Rudder trim: Right 11  1 Left 11  1 Aileron: Rigging Spec. Nr. 6760115 (from droop position) Up 15  0.5 Down 15  0.5 Droop position 1.5  0.5 down from faired Aileron trim: Up 8  1 Down 8  1 Flaps: Cessna drawing Nr. 6700750 and Rigging Spec. No. 6762715 Flap position Nominal Outboard Nominal Center Nominal Inboard Allowable tolerance Up 0 0 0  0.2 5 5.9 5.6 5.2  0.5 15 17.4 16.5 15.0  1.0 Full 39.0 37.8 36.3  2.0 Speed break: Rigging Spec. Nr. 6760275 CONTROL SURFACE Panel 3, 4, 5, 6, 7 & 8 Up: 40 -43 CESSNA 10 October 2011 EA-9810-02 Sheet 6/9 MOVEMENTS (Cont.) Maximum 1.0 between corresponding panels Roll Spoilers Rigging Spec. Nr. 6760205 Panel 1, 2, 9 and 10 Up: 40 -43 SERIAL NUMBERS ELIGIBLE 750-0001 and on. A Certificate of Airworthiness for Export endorsed as noted under "Import Requirements" must be submitted for each individual aircraft for which application for a Brazilian Certificate of Airworthiness is made. IMPORT ELEGIBILITY A Brazilian Certificate of Airworthiness may be issued on the basis of an FAA Export Certificate on Airworthiness (or a third country Export Certificate on Airworthiness, in case of used aircraft imported from such country), including the following statement: “The aircraft covered by this certificate has been inspected, tested and found to be in conformity with the Brazilian approved type design as defined by the Brazilian Type Certificate no. 9810 and in condition of safe operation.” The CTA Report H.10-2000-00, dated 29 October 1998 or further revisions, contains the Brazilian requirements for the acceptance of these airplanes. (See note 4) CERTIFICATION BASIS CERTIFICATION BASIS Brazilian Type Certificate Nr. 9810 issued on 28 October 1998 based on the RBHA 25, which endorses the FAR Part 25 effective February 1965, as amended by 25-1 through 25-74; except the following paragraph which are in the specified amendments: Additions: RBHA/FAR 25.729 (e) as amended by Amendment 25-75; and 25.1316, as amended by Amendments 25-80 RBHA 36, corresponding to FAR Part 36 effective 01 December 1969 as amended by Amendment 36-1 through 36-21 plus Noise Control Act of 1972. RBHA 34, corresponding to FAR 34 effective 10 September 1990. Special Conditions as follows. No. 25-ANM-80, additional requirements for High Altitude Operation (see note 8). No. 25-ANM-99, additional requirements for protection of Electrical and Electronic Systems from High Intensity Radiated Fields (HIRF) No. 25-ANM-113, additional requirements for operation with Fly-by- Wire Rudder Equivalent levels of safety, accepted by ANAC relative to the following requirements: RBHA/FAR 25.335 (d) and 25.341, Design Discrete Gust Criteria; RBHA/FAR 25.811 (e) (4), Red Arrow Marking for the Main Passenger Door Handle; RBHA/FAR 25.807 (e), Ditching Emergency Exits for Passenger; RBHA/FAR 25.841 (b) (6), Cabin Pressurization - High Altitude Take-off and Landing Operations; RBHA/FAR 25.1549 (a) & (c), Digital Turbine Speed; RBHA/FAR 25.1305, Digital APU Indicators (Oil Pressure, Oil Temperature, Gas Temperature, Tachometer); CESSNA 10 October 2011 EA-9810-02 Sheet 7/9 (Cont.) RBHA/FAR 25.101, 25.105, 25.109, 25.113, 25.115, 25.735 and 25.1587 Accelerate-Stop Distance; RBHA/FAR 25.811 (d) (1) and 25.812 (b) (1) (i), Emergency Exit Locator Signs; RBHA/FAR 25.201, 25.203 and 25.207, Stall Warning System for flight conditions above 34 500 feet; and RBHA/FAR 25.813(e). Emergency Exit Excess Exemptions, accepted by ANAC relative to the following requirements:  No. 6179, exemption from bird impact requirements of RBHA/FAR 25.571 (e) (1);  No. 6431, exemption from Engine-out lateral trim requirements of RBHA/FAR 25.161 (d): and  No. 6432, exemption from the emergency landing dynamic conditions of RBHA/FAR 25.562 for multiple-occupancy, side- facing divans. Expires 30 November 1996; or  No. 7922, Partial grant of exemption from the general occupant protection requirements of RBHA/FAR 25.785(b) for multiple- occupancy, side facing divans, restricted to airplanes manufactured prior to 01 January 2004.  No. 7922A, exemption from the general occupant protection requirements of RBHA/FAR 25.785(b) for multiple-occupancy, side-facing divans, (no restriction). RBHA/ FAR 25.801 ditching not complied with. Compliance with ice protection has been demonstrated in accordance with RBHA/FAR 25.1419. Application for Brazilian Type Certificate dated 10 April 1998. PRODUCTION CERTIFICATION Production Certificate No. 4 amended to add Model 750 effective 04 October 1996. See note 7 for applicable airplane serial numbers. REQUIRED EQUIPMENT The basic required equipment, as prescribed in the applicable airworthiness regulations (see Certification Basis), must be installed in the airplane. NOTES: NOTE 1 The approved Weight and Balance Manual: part number 75WB-01 (or later approved revision) is applicable to the model 750 serial number 750-0001 through 750-172 not incorporating Cessna Service Bulletin SB 750-71-10. The approved Weight and Balance Manual: part number 75WB-00 (or later approved revision) is applicable to the Model 750 serial numbers 750-0173 and on and aircraft incorporating Cessna Service Bulletin SB 750-71-10. The airplane must be loaded according to the appropriate FAA Approved Weight and Balance Manual. The list of equipment included in certificate empty weight must be provided for each airplane at the time of original certification: The certified empty weight and corresponding center of gravity location must include: Hydraulic fluid System A (Total) 16.13 kg (35.56 lb) at + 1165.4 cm (+ 458.82 in) System B (Total) 9.97 kg (21.97 lb) at + 1264.8 cm (+ 497.96 in) Unusable Fuel-Wing 29.48 kg (65.0 lb) at + 977.9 cm (+ 385.00 in) NOTE 1 Unusable Fuel-Center 6.80 kg (15.0 lb) at + 977.9 cm (+385.00 in) (cont.) Trapped Fuel 10.07 kg (22.2 lb) at + 930.3 cm (+ 366.50 in) CESSNA 10 October 2011 EA-9810-02 Sheet 8/9 Engine Unusable Oil 0.45 kg (1.0 lb) at + 1382.5 cm (+ 544.30 in) Engine Usable Oil 20.78 kg (45.8 lb) at + 1382.5 cm (+ 544.30 in) (full) NOTE 2 Approved Brazilian Airplane Flight Manual 75BR-00 (or later revision) is applicable to the Model 750 serial number 750-0001 through 750-0172 not incorporating Cessna Service Bulletin SB 750- 71-10. The Brazilian Airplane Flight Manual, corresponds to the FAA approved Airplane Flight Manual: part number 75FMA-00 (or later approved revision) plus the supplement No. 20, is applicable to the Model 750 serial number 750-0173 and on and aircraft incorporating Cessna Service Bulletin 750-71-10. The airplane must be operated according to the appropriate Approved Brazilian Airplane Flight Manual. Required Placards are translated to the Portuguese language and are listed in the Report H.10-2000-00 and were based in a CESSNA document and in the Chapter XI of the Airplane Maintenance Manual part number 75MM00 (or later approved revision). NOTE 3 Approved Airworthiness Limitations for mandatory compliance retirement life or inspection are included in the Maintenance Manual (Instructions for Continued Airworthiness), part number 75MM00 (or later approved revision), Chapter 4, Airworthiness Limitations. NOTE 4 The differences of the Brazilian airplanes in relation to the basic FAA type design are summarized below: 1 The Brazilian Airplane Flight Manual nr. 75BR-00 original dated 19 October 1998 and further revision is the AFM approved by ANAC. The Brazilian AFM nr. 75BR-00 includes the supplement 20 “Airplanes Certified to Brazilian Configuration” for the airplanes serial number 750-0001 through 750-0172 not incorporating Cessna Service Bulletin SB 750-71-10. The Brazilian AFM for Model 750 serial number 750-0173 and on and aircraft incorporating Cessna Service Bulletin SB 750-71-10, are incorporated in the FAA approved Brazilian AFM part number 75BRA-00 (or later approved revision) except the supplement 20 “Airplanes Certified to Brazilian Configuration”. 2 Markings and placards approved are those listed in the paragraph 8 of the report nr. H.10-2000-00 “Brazilian Requirements for the Acceptance of the Model 750 X”. 3 ADF1 and respective indication are required to be fed the emergency bus bar according with Brazilian operating regulations RBHA/FAR 91.205 (d). 4 For airplane with configuration of 10 or more passenger excluding seat pilots the following equipments are required to be installed: 4.1 Solid State Flight Data Recorder per RBHA/FAR 135.152. 4.2 Ground Proximity Warning System (GPWS) per RBHA/FAR 135.153. Both equipments are provided per drawing nr. 9530003 Avionics, Brazil Certification Reference Kit. 5 In accordance with RBHA/FAR 25.603 (c) a paint color limitation on upper surface of ailerons, spoilers, flaps and elevators with reflectance value of 26 or greater is requested through drawing nr. 4611003 “Exterior Control Model 750” Brazilian ECR 40602 and through Maintenance Manual 750MM Chapter 4 Airworthiness Limitation. 6 An escape hatch handle was requested through RBHA/FAR 25.809 (c) to be implemented per drawing nr. 4690072 Rev. N/C “Escape Hatch Handle” and Part List nr. 4690072 Rev. N/C “Escape Hatch Handle”. NOTE 5 All replacement seats (crew and passenger), although they may comply with TSO C127, must also be demonstrated to comply with requirements of RBHA/FAR 25.333, 25.561, 25.562 and 25.785. The foam cushion buildup of all seats (crew and passenger) may not be altered unless deviations in CESSNA 10 October 2011 EA-9810-02 Sheet 9/9 the foam construction are demonstrated by tests to comply with the listed RBHA/FAR 25 paragraphs. The LH side facing seat lap belt shall have a buckle which opens from the left to right to prevent the buckle’s own inertia from causing it to open. Any other configuration must be verified by dynamic requirements. NOTE 6 Two (2) Honeywell AZ-840 Micro Air Data Computers (MADC) are required equipment. Approved part numbers are listed in the following table: MADCPart Number Model 750-xxxx serial range Service Bulletin 7014700-904 -0003 through –0041 N/A 7014700-604 -0001, -0002, -0042 through –0015 SB 750-34-05 Rev 0,1 7014700-607 -0106 and on SB 750-34-05 Rev 2 Aircraft with part number 7014700-607 MADCs meet the initial airworthiness requirements for operation in Reduced Vertical Separation Minimum (RVSM) airspace. NOTE 7 Production Certificate No. 4 applies to Model 750 serial numbers 750-0001, 750-0002, 750-0004, 750-0006 and on. NOTE 8 Model 750 airplanes have been approved for high altitude operations (altitudes above 41 000 feet), by Special Conditions. Any modifications to the pressure vessel must be approved in accordance with the requirements as show in the certification basis. This includes modifications, which could result in a pressure vessel opening, either through crack-growth or antenna loss, greater than 3.98 sq.in. NOTE 9 The airplane is approved for Category II operations (flight-director autopilot-coupled only). This does not constitute operational approval. Minimum approved integrated computer (IC-800) software is Phase IV (P/N 7017300-31201). (General Manager, Aeronautical Product Certification)