TYPE-CERTIFICATE DATA SHEET EASA.A.022 DA 40

up 23º, ± 1º down 15º, ± 1º or values listed under (c) Aileron Elevator TCDS No. EASA.A.022 DA 40 Page 7 of 29 Issue 17, 28 August 2013 Trim tab (elevator neutral) Rudder Flaps (b) With Long Range Fuel Tank: up 23º, +0/-1º down 16º, +1/-0º or values listed under (c) (c) With MTOM 1200 kg (MÄM 40-227 installed) and for all configurations permitted: up 18°, +0/-1º down 16º, +1/-0º Serial Numbers 40.006 to 40.044 (except 40.030): Trim nose up + 18º, ± 2º Trim nose down - 33º, ± 2º Serial Numbers 40.030 and 40.045 and subsequent: Trim nose up + 12º, ± 2º Trim nose down - 39º, ± 2º With Standard Fuel Tank: Left 29º, ± 1º Right 31º, ± 1º With Long Range Fuel Tank or MÄM 40-113 (Large Rudder) installed: Left 24º, ± 1º Right 26º, ± 1º Take off flap setting 20º, ± 2º Landing flap setting 42º, ± 1º 17. Levelling Means: wedge 600 : 31 top surface of fuselage tube in front of dorsal fin 18. Minimum Flight Crew: 1 (Pilot) 19. Maximum Passenger Seating Capacity: 3 20. Baggage/Cargo Compartments: Location Max. allowable Load Behind Rear Seats 30 kg (66.14 lbs) Baggage Tube 5 kg (11.02 lbs) With Baggage Extension 45 kg (100 lbs) see note 9 21. Wheels and Tyres: Nose Wheel Tyre Size 5.00 – 5 Main Wheel Tyre Size 6.00 – 6 or 15x6.0-6 see note 8 For approved Types and rating see AMM, Doc. No. 6.02.01 22. (Reserved): N/A TCDS No. EASA.A.022 DA 40 Page 8 of 29 Issue 17, 28 August 2013 A.IV. Operating and Service Instructions 1. Flight Manual: Airplane Flight Manual Doc. No. 6.01.01-E 2. Technical Manual: Airplane Maintenance Manual Doc. No. 6.02.01 (incl. Airworthiness Limitations) Service Informations and Service Bulletins 3. Spare Parts Catalogue: Illustrated Parts Catalogue Doc. No. 6.03.01/02 4. Instruments and aggregates: refer to AMM Doc. No. 6.02.01 Chapter 1 A.V. Notes: 1. This certification applies to Serial numbers 40.006 to 40.200 for production at Diamond-Austria and Serial numbers 40.201 and subsequent for production at Diamond-Canada, excluding Serial Number 40.010. 2. Approved Noise Levels are part of the EASA Noise TCDS. 3. For Night VFR operation the optional design change OÄM 40-064 must be incorporated. 4. For IFR operation the optional design change OÄM 40-067 must be incorporated. 5. For glider towing operation the optional design change OÄM 40-063 must be incorporated. 6. Aeroplanes produced by Diamond – Canada may be imported to a country within the EU, on basis of a Canadian Certificate of Export, signed by a representative of Transport Canada covering conformity with the effective Issue of this Data Sheet. 7. The Long Range Fuel Tank, as defined in OÄM 40-071, applicable for Serial Number 40.030 and subsequent. 8. The tire dimension 15x6.0-6 is only approved in conjunction with the 18 mm MLG strut in accordance with MÄM 40-123 or the tall MLG strut in accordance to OÄM 40-283. 9. The increased baggage load is applicable if the baggage extension, Optional Design Change OÄM 40-163 is installed. 10. The landing mass of 1150 kg (2535 lbs) is only approved with Mandatory Design Change MÄM 40-123 or the tall MLG strut in accordance to OÄM 40-283 is installed. 11. The maximum take off mass of 1200kg (2646 Ibs) is only approved if mandatory design change MÄM 40-227 and a main landing gear strut by MÄM 40-123 maximum landing mass of 1150 kg (2535 Ibs) or the tall MLG strut in accordance to OÄM 40-283 is installed. 12. AVGAS 100 and 100LL also designated as 100/130 or 100/130LL, for additional approved fuel grades see AFM Section 2. TCDS No. EASA.A.022 DA 40 Page 9 of 29 Issue 17, 28 August 2013 SECTION B: DA 40 D B.I. General 1. Data Sheet No.: A.022 2. a) Type: b) Model: c) Variant: DA 40 DA 40 D -- 3. Airworthiness Category: Normal Utility 4. Type Certificate Holder: DIAMOND AIRCRAFT INDUSTRIES GMBH N.A. OTTO-STR. 5 A-2700 WIENER NEUSTADT AUSTRIA EASA.21J.052 5. Manufacturer: DIAMOND AIRCRAFT INDUSTRIES GMBH N.A. OTTO-STR. 5 A-2700 WIENER NEUSTADT AUSTRIA AT.21G.0001 SHANDONG BIN AO AIRCRAFT INDUSTRIES CO.,LTD DAGAO, ZHANHUA COUNTY, BINZHOU PEOPLE´S REPUBLIC OF CHINA EASA.21G.0014 6. Certification Application Date: 20-Feb-1997 for Major Change OÄM 40-100 - DA 40 D: 11-Jan-2002 7. National Certifying Authority Austro Control GmbH / Austria 8. National Authority Type Certificate Date: 24-Oct-2000 (JAA Recommendation Date) FZ 021-JAA B.II. EASA Certification Basis 1. Reference Date for determining the applicable requirements: 24-Oct-1998 2. Airworthiness Requirements: As defined in CRI A-01, latest issue JAR-23, issued 11-Mar-1994, incl. Amdt. 1 JAR-1, Change 5, issued 15-Jul-1996 TCDS No. EASA.A.022 DA 40 Page 10 of 29 Issue 17, 28 August 2013 3. Special Conditions: CRI E-05 Reciprocating Engine using Jet Fuel CRI E-06 Use of Diesel Fuel and Diesel/Jet Fuel Blends for Reciprocating Engines CRI E-09 Engine Vibration Level CRI E-10 Engine Torque CRI F-01 Protection from the Effects of HIRF CRI F-03 Protection from the Effects of Lightning Strikes, Indirect Effects CRI F-06 Installation of a FADEC Diesel Engine and Propeller CRI F-07 Human Factors in Integrated Avionic Systems CRI F-08 Software, Hardware Assurance Level and Highly, Integrated or Complex Aircraft Systems CRI F-08 Software, Hardware Assurance Level and Highly Integrated or Complex Aircraft Systems 3. Exemptions: None 4. Deviations: None 5. Equivalent Safety Findings: CRI D-01 Single Lever Power Control CRI E-07 Coolant Tank CRI E-08 Electronically-controlled Reciprocating Diesel Engine CRI E-11 Fuel System – Hot Fuel Temperature CRI F-05 Powerplant Instruments 6. Requirements elected to comply: None 7. Environmental Standards: ICAO, Annex 16, Volume 1, Third Edition, 1993, Amdt. 7 JAR 36, issued 23-May-1997 CRI A-03 for additional national requirements See Note 2 8. Additional National Requirements: N/A 9. (Reserved) N/A B.III. Technical Characteristics and Operational Limitations 1. Type Design Definition: Current issue of Doc. No. 6.07.00, Chapter O100/7 including Design Changes MÄM 40-075 and following 2. Description: Single diesel engine, four-seated cantilever low wing airplane, composite construction, fixed tricycle landing gear, T-tail TCDS No. EASA.A.022 DA 40 Page 11 of 29 Issue 17, 28 August 2013 3. Equipment: Equipment list, AFM, Doc. No. 6.01.05, Section 6 see Note 9 4. Dimensions: Span Length Height Wing Area 11.94 m (39 ft 2 in) 8.01 m (26 ft 3 in) 1.97 m (6 ft 6 in) 13.54 m² (146 sqft) 5. Engine: 5.1.1 Model: 1 Thielert TAE 125-01 or TAE 125-02-99 see Note 10 and Note 11 5.1.2 Type Certificate: Engine Type Certificate Data Sheet EASA E.055 5.1.3 Firmware: see Note 5; MSB D4-044 5.1.4 Mapping see Note 5; MSB D4-044 5.1.5 Limitations: Max take-off rotational speed 2300 r.p.m. Max continuous rotational speed 2300 r.p.m (Propeller shaft r.p.m) For power-plants limits refer to AFM, Doc. No. 6.01.05, Section 2 6. Load factors: at vA at vNE with flaps in T/O or LDG position Normal Category Positive: 3.8 3.8 2.0 Negative -1.52 0 Utility Category Positive: 4.4 4.4 2.0 Negative: -1.76 -1 7. Propeller: 7.1 Model: 1 mt-Propeller MTV-6-A/187-129 7.2 Type Certificate: EASA Propeller Type Certificate Data Sheet P.094 7.3 Number of blades: 3 7.4 Diameter: 1870 mm 7.5 Sense of Rotation: Clockwise 7.6 Settings: Low pitch setting: 12 ° High pitch setting: 28 ° 8. Fluids: 8.1 Fuel: Jet A-1 (ASTM 1655) see Note 12 Diesel (EN 590) see Note 6 TCDS No. EASA.A.022 DA 40 Page 12 of 29 Issue 17, 28 August 2013 8.2 Oil: Engine: Shell Helix Ultra 5W30 synthetic API SJ/CF For more details see AFM, Doc. No. 6.01.05, Section 2 Gearbox: Shell EP 75W90 API GL-4 For more details see AFM, Doc. No. 6.01.05, Section 2 8.3 Coolant: Water / Cooler Protection-Mixture for more details see AFM, 6.01.05, Section 2 9. Fluid capacities: 9.1 Fuel: Standard Fuel Tank Total: 113.6 liters 30 US Gallons Usable: 106.0 liters 28 US Gallons Long Range Fuel Tank Total: 155.2 liters 41 US Gallons Usable: 147.6 liters 39 US Gallons 9.2 Oil: Maximum: 6.0 liters 6.3 qts Minimum: 4.5 liters 4.8 qts 9.3 Coolant system capacity: Approx. 7 Liter 10. Air Speeds: Design Manoeuvring Speed vA : up to 980 kg 94 KIAS above 980 kg 108 KIAS Flap Extended Speed v FE : full flaps 91 KIAS take-off flaps 108 KIAS Maximum structural cruising speed vNO (= Maximum structural design speed vC): 129 KIAS Never exceed speed v NE : 178 KIAS 11. Maximum Operating Altitude: 5000 m (16 404 ft) 12. Allweather Operations Capability: Day-VFR Night VFR IFR see Note 3 Flight into expected or actual icing conditions is prohibited TCDS No. EASA.A.022 DA 40 Page 13 of 29 Issue 17, 28 August 2013 13. Maximum Weights: Take-off: Utility Category: 980 kg (2161 lb) Normal Category: 1150 kg (2535 lb) Landing: 1092 kg (2407 lb) or 1150 kg (2535 lbs) see Note 8 14. Centre of Gravity Range: Forward limit up to 980 kg 2.40 m behind Datum at 1150 kg 2.46 m behind Datum varying linearly with mass in between Rear limit for all masses 2.59 m behind Datum with Long Range Fuel Tank 2.55 m behind Datum 15. Datum: 2.194 mm in front of leading edge of stub-wing at the wing joint 16. Control surface deflections: up 20º, ± 2º down 13º, +2/-0º With Standard Fuel Tank: up 23º, ± 1º down 15º, ± 1º With Long Range Fuel Tank installed: up 23º, +0/-1º down 16º, +1/-0º Trim nose up + 12º, ± 2º Trim nose down - 39º, ± 2º With Standard Fuel Tank: Left 29º, ± 1º Right 31º, ± 1º With Long Range Fuel Tank or MÄM 40-113 (Large Rudder) installed: Left 24º, ± 1º Right 26º, ± 1º Take off flap setting 20º, ± 2º Landing flap setting 42º, ± 1º Aileron Elevator Trim tab (elevator neutral) Rudder Flaps 17. Levelling Means: wedge 600 : 31 top surface of fuselage tube in front of dorsal fin 18. Minimum Flight Crew: 1 (Pilot) 19. Maximum Passenger Seating Capacity: 3 TCDS No. EASA.A.022 DA 40 Page 14 of 29 Issue 17, 28 August 2013 20. Baggage/Cargo Compartments: Location Max. allowable Load Behind Rear Seats 30 kg (66.14 lbs) Baggage Tube 5 kg (11.02 lbs) With Baggage Extension 45 kg (100 lbs) see note 7 21. Wheels and Tyres: Nose Wheel Tyre Size 5.00 – 5 Main Wheel Tyre Size 6.00 – 6 or 15x6.0-6 see note 4 For approved types and rating see AMM, Doc. No. 6.02.01 22. (Reserved): N/A B.IV. Operating and Service Instructions 1. Flight Manual: Airplane Flight Manual Doc. No. 6.01.05-E 2. Technical Manual: Airplane Maintenance Manual Doc. No. 6.02.01 (incl. Airworthiness Limitations) Service Informations and Service Bulletins 3. Spare Parts Catalogue: Illustrated Parts Catalogue Doc. No. 6.03.05 4. Instruments and aggregates: refer to AMM Doc. No. 6.02.01 Chapter 1 TCDS No. EASA.A.022 DA 40 Page 15 of 29 Issue 17, 28 August 2013 B.V. Notes: 1. This certification applies to Serial Numbers 40.080, 40.084 and D4.001 and subsequent, with the exception of Serial Number D4.013, D4.111, D4.198, D4.199, D4.200 and D4.201 for the Production in Austria. Serial Numbers 40.DS001 and subsequent are applicable for the production in China. 2. Approved Noise Levels are part of the EASA Noise TCDS. 3. For IFR operation the optional design change OÄM 40-136 or OÄM 40-193 must be incorporated. 4. The tire dimension 15x6.0-6 is only approved in conjunction with the 18 mm MLG strut in accordance with MÄM 40-123. 5. For approved engine software version (Firmware and Mapping) of TAE 125-01 or TAE 125-02-99 see DAI Service Bulletin MSB D4-044, latest issue. 6. Operation with Diesel fuel is only approved if MÄM 40-129 is incorporated. 7. The increased baggage load is applicable if the baggage extension, Optional Design Change OÄM 40-163 is installed. 8. The landing mass of 1150 kg (2535 lbs) is only approved with Mandatory Design Change MÄM 40-123 is installed. 9. Installation of the G1000 Integrated Avionic System is only approved if OÄM 40- 193 (IFR) or 40-224 (VFR) is incorporated. For approved software version see DAI Service Bulletin MSB D4-045, latest issue. 10. Approved engine model for installation in the DA 40D:  TAE 125-01 125-01-(005)-( )  TAE 125-02-99 125-02-(0001)-( ) Engine TAE 125-02-99 was previously approved as TAE 125-02 11. Engine retrofit installation from engine TAE 125-01 to TAE 125-02-99 is approved by Design Change MÄM 40-256 with OSB D4-061. 12. For additional approved Jet Fuel specifications see AFM Section 2. TCDS No. EASA.A.022 DA 40 Page 16 of 29 Issue 17, 28 August 2013 SECTION C: DA 40 F C.I. General 1. Data Sheet No.: A.022 2. a) Type: b) Model: c) Variant: DA 40 DA 40 F -- 3. Airworthiness Category: Normal Utility (see Note 6) 4. Type Certificate Holder: DIAMOND AIRCRAFT INDUSTRIES GMBH N.A. OTTO-STR. 5 A-2700 WIENER NEUSTADT AUSTRIA EASA.21J.052 5. Manufacturer: DIAMOND AIRCRAFT INDUSTRIES GMBH N.A. OTTO-STR. 5 A-2700 WIENER NEUSTADT AUSTRIA AT.21G.0001 DIAMOND AIRCRAFT INDUSTRIES INC. 1560 CRUMLIN SIDEROAD, LONDON ONTARIO, N5V 1S2 CANADA 161-93 (TCCA) 6. Certification Application Date: 20-Feb-1997 8. July 2004 for DA 40 F (VÄM 40-002) 7. National Certifying Authority N/A 8. National Authority Type Certificate Date: N/A C.II. EASA Certification Basis 1. Reference Date for determining the applicable requirements: 24-Oct-1998 2. Airworthiness Requirements: As defined in CRI A-01, latest issue JAR-23, Change -, issued 11-Mar-1994 JAR-1, Change 5, issued 15-Jul-1996 TCDS No. EASA.A.022 DA 40 Page 17 of 29 Issue 17, 28 August 2013 3. Special Conditions: CRI F-01 Protection from the Effects of HIRF CRI F-03 Protection from the Effects of Lightning Strikes, Indirect Effects CRI O-01 Glider Towing CRI O-02 Tow Cable Retraction Mechanisms 3. Exemptions: None 4. Deviations: None 5. Equivalent Safety Findings: None 6. Requirements elected to comply: JAR-23, NPA 23-3, ACJ Material 7. Environmental Standards: ICAO Annex 16, Volume 1, Part 2, Chapter 10, Amendment 7 , CRI A-03F 8. Additional National Requirements: None 9. (Reserved) N/A C.III. Technical Characteristics and Operational Limitations 1. Type Design Definition: Current issue of Doc.No. 6.07.00, Chapter V002/7 Design Change VÄM 40-002 (including and excluding the design changes as listed in the VÄM). 2. Description: Single engine, four-seated cantilever low wing airplane, composite construction, fixed tricycle landing gear, T- tail, fix pitch propeller. 3. Equipment: Equipment list, AFM, Doc.No. 6.01.02, Section 6 4. Dimensions: Span Length Height Wing Area 11.94 m (39 ft 2 in) 8.01 m (26 ft 3 in) 1.97 m (6 ft 6 in) 13.54 m² (146 sqft) 5. Engine: 5.1.1 Model: 1 Textron Lycoming O-360-A4M 5.1.2 Type Certificate: FAA Engine Type Certificate Data Sheet 286 5.1.3 Limitations: Max take-off rotational speed 2700 r.p.m. Max continuous rotational speed 2700 r.p.m For power-plants limits refer to AFM, Doc. No. 6.01.02, Section 2 TCDS No. EASA.A.022 DA 40 Page 18 of 29 Issue 17, 28 August 2013 6. Load factors: at vA at vNE with flaps in T/O or LDG position Normal Category Positive: 3.8 3.8 2.0 Negative -1.52 0 Utility Category Positive: 4.4 4.4 2.0 Negative: -1.76 -1 7. Propeller: 7.1 Model: 1 Sensenich 76EM8S10-0-63 or 1 Mühlbauer MT 188R135-4G 7.2 Type Certificate: FAA TCDS P4EA (Sensenich 76EM8S10-0-63) or EASA TCDS P.006 (Mühlbauer MT 188R135-4G) 7.3 Number of blades: 2 7.4 Diameter: 1930 mm (Sensenich 76EM8S10-0-63) 1880 mm (Mühlbauer MT 188R135-4G) 7.5 Sense of Rotation: Clockwise 8. Fluids: 8.1 Fuel: AVGAS 100 LL, 100 (ASTM D910) see Note 7 8.2 Oil: Oils conforming to spec. SAE J1899 / MIL-L-22851 For more details see AFM, Doc. No. 6.01.02, Section 2 8.3 Coolant: N/A 9. Fluid capacities: 9.1 Fuel: Standard Fuel Tank: Total: 156 liters 41.2 US Gallons Usable: 152.2 liters 40.2 US Gallons Long Range Fuel Tank: Total: 193 liters 51 US Gallons Usable: 189.2 liters 50 US Gallons 9.2 Oil: Maximum: 7.70 liters 8 qts Minimum: 3.785 liters 4 qts 9.3 Coolant system capacity: N/A TCDS No. EASA.A.022 DA 40 Page 19 of 29 Issue 17, 28 August 2013 10. Air Speeds: Design Manoeuvring Speed vA : up to 980 kg 94 KIAS above 980 kg 108 KIAS Flap Extended Speed v FE : full flaps 91 KIAS take-off flaps 108 KIAS Maximum structural cruising speed vNO (= Maximum structural design speed vC): 129 KIAS Never exceed speed v NE : 178 KIAS 11. Maximum Operating Altitude: 5000 m (16 404 ft) 12. All-weather Operations Capability: Day VFR Night VFR IFR Flight into expected or actual icing conditions is prohibited 13. Maximum Weights: Take-off: Utility Category: 980 kg (2161 lb) Normal Category: 1150 kg (2535 lb) Landing: 1150 kg (2535 lbs) 14. Centre of Gravity Range: Forward limit up to 980 kg 2.40 m behind Datum at 1150 kg 2.46 m behind Datum varying linearly with mass in between Rear limit for all masses 2.59 m behind Datum with Long Range Fuel Tank 2.55 m behind Datum 15. Datum: 2.194 mm in front of leading edge of stub-wing at the wing joint 16. Control surface deflections: up 20º, ± 2º down 13º, +2/-0º With Standard Fuel Tank: Aileron Elevator TCDS No. EASA.A.022 DA 40 Page 20 of 29 Issue 17, 28 August 2013 Trim tab (elevator neutral) Rudder Flaps up 23º, ± 1º down 15º, ± 1º With Standard Fuel Tank for intentional spinning (see Note 6): up 21º, ± 0.5º down 18º, ± 0.5º With Long Range Fuel Tank: up 23º, +0/-1º down 16º, +1/-0º Nose up + 12º, ± 2º Nose down - 39º, ± 2º Left 24º, ± 1º Right 26º, ± 1º Take off flap setting 20º, ± 2º Landing flap setting 42º, ± 1º 17. Levelling Means: wedge 600 : 31 top surface of fuselage tube in front of dorsal fin 18. Minimum Flight Crew: 1 (Pilot) 19. Maximum Passenger Seating Capacity: 3 20. Baggage/Cargo Compartments: Location Max. allowable Load Behind Rear Seats 30 kg (66.14 lbs) Baggage Tube 5 kg (11.02 lbs) With Baggage Extension 45 kg (100 lbs) see note 5 21. Wheels and Tyres: Nose Wheel Tyre Size 5.00 – 5 Main Wheel Tyre Size 6.00 – 6 or 15x6.0-6 For approved Types and rating see AMM, Doc. No. 6.02.01 22. (Reserved): N/A TCDS No. EASA.A.022 DA 40 Page 21 of 29 Issue 17, 28 August 2013 C.IV. Operating and Service Instructions 1. Flight Manual: Airplane Flight Manual Doc. No. 6.01.02-E 2. Technical Manual: Airplane Maintenance Manual Doc. No. 6.02.01 (incl. Airworthiness Limitations) Service Informations and Service Bulletins 3. Spare Parts Catalogue: Illustrated Parts Catalogue Doc. No. 6.03.01/02 4. Instruments and aggregates: refer to AMM Doc. No. 6.02.01 Chapter 1 C.V. Notes: 1. This certification applies to Serial numbers 40.F001 and subsequent for production at Diamond-Austria, and Serial numbers 40.FC001 and subsequent for production at Diamond-Canada. 2. Approved Noise Levels are part of the EASA Noise TCDS. 3. reserved. 4. Aeroplanes produced by Diamond – Canada may be imported to a country within the EU, on basis of an Canadian Certificate of Export, signed by a representative of Transport Canada covering conformity with the effective Issue of this Data Sheet. 5. The increased baggage load is applicable if the baggage extension, Optional Design Change OÄM 40-163, is installed. 6. The DA40F is certified for intentional spin if OÄM 40-201 is installed. The following additional Limitations/Conditions apply:  Center of Gravity Range 2,45 – 2,50 m  Maximum fuel loading 2x38 liters (2x10gal)  Canopy Jettison System OÄM 40-203 must be installed  Mt Propeller MT 188R135-4G must be installed  Elevator settings must be according to OÄM 40-201  Long Range Tank must not be installed  Wheel fairings must not be installed  Baggage is not allowed 7. AVGAS 100 and 100LL also designated as 100/130 or 100/130LL, for additional approved fuel grades see AFM Section 2 TCDS No. EASA.A.022 DA 40 Page 22 of 29 Issue 17, 28 August 2013 SECTION D: DA 40 NG D.I. General 1. Data Sheet No.: A.022 2. a) Type: b) Model: c) Variant: DA 40 DA 40 NG -- 3. Airworthiness Category: Normal 4. Type Certificate Holder: DIAMOND AIRCRAFT INDUSTRIES GMBH N.A. OTTO-STR. 5 A-2700 WIENER NEUSTADT AUSTRIA EASA.21J.052 5. Manufacturer: DIAMOND AIRCRAFT INDUSTRIES GMBH N.A. OTTO-STR. 5 A-2700 WIENER NEUSTADT AUSTRIA AT.21G.0001 6. Certification Application Date: 20-Feb-1997 for Major Change VÄM 40-004 - DA 40 NG: 17-Jan-2008 7. National Certifying Authority N/A 8. National Authority Type Certificate Date: N/A D.II. EASA Certification Basis 1. Reference Date for determining the applicable requirements: 24-Oct-1998 2. Airworthiness Requirements: As defined in CRI A-01 NG, latest issue JAR-23, issued 11-Mar-1994, incl. Amdt. 1 3. Special Conditions: CRI E-05 Reciprocating Engine using Jet Fuel CRI E-06 Use of Diesel Fuel and Diesel/Jet Fuel Blends for Reciprocating Engines CRI E-09 Engine Vibration Level CRI E-10 Engine Torque CRI F-01 Protection from the Effects of HIRF TCDS No. EASA.A.022 DA 40 Page 23 of 29 Issue 17, 28 August 2013 CRI F-03 Protection from the Effects of Lightning Strikes, Indirect Effects CRI F-06 Installation of a FADEC Diesel Engine and Propeller CRI F-07 Human Factors in Integrated Avionic Systems 3. Exemptions: None 4. Deviations: None 5. Equivalent Safety Findings: CRI D-01 Single Lever Power Control CRI E-07 Coolant Tank CRI E-08 Electronically-controlled Reciprocating Diesel Engine CRI E-11 Fuel System – Hot Fuel Temperature CRI E-12 Electric Fuel Pumps CRI B-01 Stall Warning CRI F-05 Powerplant Instruments 6. Requirements elected to comply: None 7. Environmental Standards: ICAO, Annex 16, Volume 1, Chpt. 10, 5. Edition CS 36, Amendment 1 8. Additional National Requirements: N/A 9. (Reserved) N/A D.III. Technical Characteristics and Operational Limitations 1. Type Design Definition: Current issue of Doc. No. 6.07.00, Chapter V004/7 together with Design Changes VÄM 40-004; MÄM 40-398; MÄM 40-403; MÄM 40-404; MÄM 40- 409; MÄM 40-411; MÄM 40-414; OÄM 40-306 + OÄM 40-307 or MÄM 40-574; and following 2. Description: Single diesel engine, four-seated cantilever low wing airplane, composite construction, fixed tricycle landing gear, T-tail, winglets (option) 3. Equipment: Equipment list, AFM, Section 6 4. Dimensions: Span Length Height Wing Area 11.63 m (38 ft 2 in) 8.06 m (26 ft 5 in) 1.97 m ( 6 ft 6 in) 13.244 m² (142,6 sqft) TCDS No. EASA.A.022 DA 40 Page 24 of 29 Issue 17, 28 August 2013 5. Engine: 5.1.1 Model: 1 Austro Engine E4, see Note 7 5.1.2 Type Certificate: Engine Type Certificate Data Sheet EASA E.200 5.1.3 Firmware: see Note 3; MSB 40NG-002 5.1.4 Mapping see Note 3; MSB 40NG-002 5.1.5 Limitations: Max take-off rotational speed 2300 r.p.m. Max continuous rotational speed 2100 r.p.m (Propeller shaft r.p.m) For power-plants limits refer to AFM, Section 2 6. Load factors: at vA at vNE with flaps in T/O or LDG position Positive: 3.8 3.8 2.0 Negative -1.52 0 7. Propeller: 7.1 Model: 1 mt-Propeller MTV-6-R/190-69 7.2 Type Certificate: EASA Propeller Type Certificate Data Sheet P.094 7.3 Number of blades: 3 7.4 Diameter: 1900 mm 7.5 Sense of Rotation: Clockwise 7.6 Settings: Low pitch setting: 14.5°± 0.2° (@0.75R) High pitch setting: 35°± 1.0° (@0.75R) 8. Fluids: 8.1 Fuel: Jet A, Jet A-1 (ASTM 1655) see note 6 8.2 Oil: Engine: Shell Helix Ultra 5W30 and 5W40 Gearbox: Shell SPIRAX GSX or S6 GXME 75W-80 8.3 Coolant: Water / Cooler Protection-Mixture for more details see AFM, Section 2 9. Fluid capacities: 9.1 Fuel: Standard Fuel Tank Total: 113.6 liters 30 US Gallons Usable: 106.0 liters 28 US Gallons Long Range Fuel Tank Total: 155.2 liters 41 US Gallons Usable: 147.6 liters 39 US Gallons 9.2 Oil: Maximum: 7.0 liters Minimum: 5.0 liters TCDS No. EASA.A.022 DA 40 Page 25 of 29 Issue 17, 28 August 2013 9.3 Coolant system capacity: Approx. 7 Liter 10. Air Speeds: Operating Manoeuvring Speed v O: up to 1080 kg 101 KIAS from 1080 to 1180 kg 108 KIAS above 1180 kg 113 KIAS Flap Extended Speed v FE : full flaps 98 KIAS take-off flaps 110 KIAS Maximum structural cruising speed vNO (= Maximum structural design speed vC): 130 KIAS Never exceed speed v NE : 172 KIAS 11. Maximum Operating Altitude: 5000 m (16 404 ft) 12. All-weather Operations Capability: Day-VFR Night VFR IFR Flight into expected or actual icing conditions is prohibited 13. Maximum Weights: Take-off: 1280 kg (2822 lb) Landing: 1216 kg (2681 lb) 1280 kg (2822 lb) see note 8 Minimum Flight: 940 kg (2072 Ib) Maximum Zero Fuel: 1200 kg (2646 Ib) 1265 kg (2789 Ib) see note 8 14. Centre of Gravity Range: Forward limit from 940 to 1080 kg 2.40 m behind Datum at 1280 kg 2.46 m behind Datum varying linearly with mass in between Rear limit 2.53 m behind Datum 15. Datum: 2.194 mm in front of leading edge of stub-wing at the wing joint 16. Control surface deflections: up 20º, ± 2º down 13º, +2/-2º up 21º, +0/-1º Aileron Elevator TCDS No. EASA.A.022 DA 40 Page 26 of 29 Issue 17, 28 August 2013 Trim tab (elevator neutral) Rudder Flaps down 17º, +1/-0º Trim nose up + 12º, ± 2º Trim nose down - 39º, ± 2º Left 24º, ± 1º Right 26º, ± 1º Take off flap setting 20º, ± 2º Landing flap setting 42º, ± 1º 17. Levelling Means: wedge 600 : 31 top surface of fuselage tube in front of dorsal fin 18. Minimum Flight Crew: 1 (Pilot) 19. Maximum Passenger Seating Capacity: 3 20. Baggage/Cargo Compartments: Location Max. allowable Load Behind Rear Seats 30 kg (66.14 lbs) Baggage Tube 5 kg (11.02 lbs) Short Baggage Extension 15 kg (33 lbs) see note 4 With Baggage Extension 45 kg (100 lbs) see note 4 21. Wheels and Tyres: Nose Wheel Tyre Size 5.00–5, 6 PR, 120mph OÄM 40-334: 6.00-6, 6 PR, see note 8 Main Wheel Tyre Size 15x6.0-6, 6 PR, 160 mph OÄM 40-334: 8.50-6, 6 PLY, see note 8 22. (Reserved): N/A TCDS No. EASA.A.022 DA 40 Page 27 of 29 Issue 17, 28 August 2013 D.IV. Operating and Service Instructions 1. Flight Manual: Airplane Flight Manual Doc. No. 6.01.15-E 2. Technical Manual: Airplane Maintenance Manual Doc. No. 6.02.15 (incl. Airworthiness Limitations) Service Informations and Service Bulletins 3. Spare Parts Catalogue: Illustrated Parts Catalogue Doc. No. 6.03.15 4. Instruments and aggregates: refer to AMM Doc. No. 6.02.15 Chapter 1 D.V. Notes: 1. This certification applies to Serial Numbers D4.111, D4.365, 40.N001 and subsequent, for the Production in Austria. DA 40 D airplanes with Serial Numbers 40.080, 40.084, D4.001 and subsequent manufactured in Austria may be converted to Model DA 40 NG by DAI approved Service Bulletin OSB D4-080. 2. Approved Noise Levels are part of the EASA Noise TCDS. 3. For approved E4 engine software version see DAI Service Bulletin MSB 40NG- 002, latest issue. 4. The baggage load in the short baggage extension is applicable if Optional Design Change OÄM 40-331 is installed. The increased baggage load of 45 kg (100 lbs) is applicable if the baggage extension, Optional Design Change OÄM 40-164, is installed. 5. For approved software version of the G1000 Integrated Avionic System see DAI Service Bulletin MSB 40NG-003, latest issue. 6. For additional approved Jet Fuel specifications see AFM Section 2. 7. Approved engine model configuration for installation in the DA 40 NG: E4-A 8. The Maximum Landing Mass of 1280 kg and Maximum Zero Fuel Mass of 1265 kg (MÄM 40-429/a) is only applicable, if Optional Design Change OÄM 40-334 (reinforcements, struts and large wheels) or Mandatory Design Change MÄM 40- 574 (reinforcements and struts) is installed. For approved wheel brands and types refer to the AFM and AMM. 9. For glider towing operation the optional design change OÄM 40-312 must be incorporated TCDS No. EASA.A.022 DA 40 Page 28 of 29 Issue 17, 28 August 2013 ADMINISTRATIVE SECTION I. Acronyms II. Type Certificate Holder Record DIAMOND AIRCRAFT INDUSTRIES GMBH N.A. OTTO-STR. 5 A-2700 WIENER NEUSTADT AUSTRIA III. Change Record Issue Date Changes TC Issue No. & Date Issue 1 18-Jan-2005 Transfer from JAA TCDS JAA/23/00-001 issue 12 to the EASA Type Design Landing mass 1150 kg 21-Jan-2005 Issue 2 15-Apr-2005 DA 40 F Variant 15-Apr-2005 Issue 3 28-Sep-2005 MÄM 40-071/c Fuel Capacity OÄM 40-193, 40-224 Garmin G1000 Integrated Avionic System MÄM 40-216 Engine Temp. Range Page 1: Issue 3 added Page 1: List of effective pages updated Page 4: CRI O-02 Name corrected Page 4, 5, 6, 9, 10, 11: Numbering / formatting corrected Page 5: Fuel tank capacity corrected Page 7, 13, 14, 15, 16: Formatting corrected Page 9: CRI F-07 and CRI F-08 added Page 9: Section 2.B.III.3 Reference to Notes added Page 10: “Distilled Water / Cooler Protection” changed to “Water / Cooler Protection-Mixture” Page 12: Section 2.B.V.5: Reference changed to DAI MSB Page 12: Section 2.B.V Note 9 and 10 added. Page 13: CRI O-02 Name corrected Page 14: Fuel tank capacity corrected Page 17: Numbering corrected Page 17: Issue 3 added - Issue 4 21-Dec-2006 MÄM 40-256 Engine TAE 125-02 in the DA40D Page 9: Section 2, BIII.5 : add engine TAE125-02 and Note 10 and 11 Page 11: Section 2, BV.2 : add noise level for engine TAE 125-02 Page 11: Section 2, BV.5 : engine TAE 125-02 Page 11: Section 2, BV.10 : add engine model Page 11 : Section 2, BV.11 : add engine retrofit - TCDS No. EASA.A.022 DA 40 Page 29 of 29 Issue 17, 28 August 2013 Issue 5 28-Mar-2007 OÄM 40-203 DA40F propeller MT188R135-4G OÄM 40-201 DA40F Intentional spin Deletion of conforming Serial Number 40.010 MÄM 40-227, DA40 T/O mass 1200 kg EASA Noise TCDS Page 14 : Section 3, CIII.7 : add propeller Page 6 : Section 1, A.V.1 : ex 40.010 Page 16 : Section 3, C.V. add. Note 6 Page 7 : Section 1, A.V. add Note 11 Page 4 : section 1, AII.10, add. CRI A-03 1200 kg Page 6 : Section 1, AV.2 delete noise data Page 11,12 : section 2 BV. Delete noise data Page 16 : section 3 CV. Delete noise data Page 16 : section 3, AV.3. note 3 deleted not valid for DA40F - Issue 6 11-Jun-2007 Engine redefinition from TAE 125-02 to TAE 125-02-99 Page 9: Section 2, BIII.5 : Page 11: Section 2, BV.2 : Page 11: Section 2, BV.5 : Page 11: Section 2, BV.10 : Page 11 : Section 2, BV.11 : Correction of the CG range for 1200 kg max Takeoff mass Page 5 : section 1, AIII.14, change fwd limit 2,48 at 1200 kg - Issue 7 China Production Delete experimental airplane D4.111 “Tall” main landing gear strut OÄM40-283 page 6 : Section 1, AV.8 page 11, 12 : Section 2. BV.1 page 8, 12 : Section 2, BI.4 page 10 : Section 2, BIII.7 page 4 : Section 1, AIII.7 page13 :Section 3, CI,4 - Issue 8 10-Jul-2009 Fuel TS-1 dir the DA40D , EASA Project P-EASA.A.C.12579 B.III 8.1 and B IV add Note 12 A.V. Note 11 editorial corrections - Issue 9 08-Apr-2010 Variant DA 40 NG; EASA Project No. P-EASA.A.C.09011 Section 4 added 08-Apr-2010 Issue 10 New Layout. Section D: Note 1 modified to include converted aircraft. EASA Project No. 0010006923 Baggage load for short baggage extension added. Note 4 modified. EASA Project No. 0010006848 TS-1 Fuel added to note 6, EASA Project No. 0010007198 - Issue 11 24-Mar-2011 Section D.III and D.V: Increased Maximum Landing Mass of 1280 kg, wheels, tyres and note 8 added, EASA Project No. 0010008884 - Issue 12 12-Apr-2011 Section D.V, Note 6: Additional Fuel Grades added, EASA Project No. 0010009256-001 - Issue 13 15-Sep-2011 Corrections Section B.V, Note 12; C.V, Note 6: General Ref. to AFM - Issue 14 17-Feb-2012 Section D.III.13: Increased Maximum Landing Mass of 1280 kg design Change MÄM 40-574, note 8 extended, EASA Project 0010007848 Section D.III.8.2: Gearbox Oil brand name corrected - Issue 15 18-April-2012 Section D, DIII.13, DV Note 8 Maximum Zero Fuel Mass 1265 kg Design Change MÄM 40-429/a EASA Project 0010015705 - Issue 16 23-August- 2013 Section D, DV Note 9 sdded Glider Towing DA 40 NG Design Change OÄM 40-312 EASA Project 0010004590 - Issue 17 28- August 2013 Section A, A.III. 8.1., A.V. Note 12 added Section C, C.III. 8.1., A.V. Note 7 added Additional Fuel Grades AVGAS 100 MÄM 40-617 EASA Project 0010020527 -