Garmin G1000 Cockpit Reference Guide for the Diamond Da42

with all air traffic control altitude regulations, requirements, instructions, and clearances. WaRNING: Do not use basemap information (land and water data) as the sole means of navigation. Basemap data is intended only to supplement other approved navigation data sources and should be considered only an aid to enhance situational awareness. WaRNING: Do not rely solely upon the display of traffic information to accurately depict all of the traffic within range of the aircraft. Due to lack of equipment, poor signal reception, and/or inaccurate information from aircraft or ground stations, traffic may be present that is not represented on the display. WaRNING: Do not use data link weather information for maneuvering in, near, or around areas of hazardous weather. Information contained within data link weather products may not accurately depict current weather conditions. WaRNING: Do not use the indicated data link weather product age to find the age of the weather information shown by the data link weather product. Due to time delays inherent in gathering and processing weather data for data link transmission, the weather information shown by the data link weather product may be older than the indicated weather product age. WaRNING: Do not use terrain avoidance displays as the sole source of information for maintaining separation from terrain and obstacles. Garmin obtains terrain and obstacle data from third party sources and cannot independently verify the accuracy of the information. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Warnings, Cautions & Notes WaRNING: Do not rely on the displayed minimum safe altitude (MSAs) as the sole source of obstacle and terrain avoidance information. Always refer to current aeronautical charts for appropriate minimum clearance altitudes. WaRNING: Do not use GPS to navigate to any active waypoint identified as a ‘NON WGS84 WPT’ by a system message. ‘NON WGS84 WPT’ waypoints are derived from an unknown map reference datum that may be incompatible with the map reference datum used by GPS (known as WGS84) and may be positioned in error as displayed. WaRNING: Do not rely on the autopilot to level the aircraft at the MDA/DH when flying an approach with vertical guidance. The autopilot will not level the aircraft at the MDA/DH even if the MDA/DH is set in the altitude preselect. WaRNING: Do not rely on the accuracy of attitude and heading indications in the following geographic areas (due to variations in the earth’s magnetic field): North of 72° North latitude at all longitudes; South of 70° South latitude at all longitudes; North of 65° North latitude between longitude 75° W and 120° W. (Northern Canada); North of 70° North latitude between longitude 70° W and 128° W. (Northern Canada); North of 70° North latitude between longitude 85° E and 114° E. (Northern Russia); South of 55° South latitude between longitude 120° E and 165° E. (Region south of Australia and New Zealand). WaRNING: Use appropriate primary systems for navigation, and for terrain, obstacle, and traffic avoidance. Garmin SVT™ is intended as an aid to situational awareness only and may not provide either the accuracy or reliability upon which to solely base decisions and/or plan maneuvers to avoid terrain, obstacles, or traffic. WaRNING: Do not use the Garmin SVT runway depiction as the sole means for determining the proximity of the aircraft to the runway or for maintaining the proper approach path angle during landing. WaRNING: Do not operate the weather radar in a transmitting mode when personnel or objects are within the MPEL boundary. WaRNING: Always position the weather radar gain setting to Calibrated for viewing the actual intensity of precipitation. Changing the gain in weather mode causes precipitation intensity to be displayed as a color not representative of the true intensity. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Warnings, Cautions & Notes WaRNING: Do not consider the overflight of thunderstorms to be safe, as extreme turbulence may exist significantly above observed returns. WaRNING: Do not rely on information from a lightning detection system display as the sole basis for hazardous weather avoidance. Range limitations and interference may cause the system to display inaccurate or incomplete information. Refer to documentation from the lightning detection system manufacturer for detailed information about the system. WaRNING: Do not use a QFE altimeter setting with this system. System functions will not operate properly with a QFE altimeter setting. Use only a QNH altimeter setting for height above mean sea level, or the standard pressure setting, as applicable. WaRNING: Do not use SurfaceWatch™ information as the primary method of flight guidance during airborne or ground operations. SurfaceWatch does not have NOTAM or ATIS information regarding the current active runway, condition, or information about the position of hold lines. CaUTIoN: Do not clean display surfaces with abrasive cloths or cleaners containing ammonia. They will harm the anti-reflective coating. CaUTIoN: Do not allow repairs to be made by anyone other than an authorized Garmin service center. Unauthorized repairs or modifications could void both the warranty and affect the airworthiness of the aircraft. CaUTIoN: Never disconnect power to the system when loading a database. Power interruption during the database loading process could result in maintenance being required to reboot the system. CaUTIoN: When downloading updates to the Jeppesen Navigation Database, copy the data to an SD card other than a Garmin Supplemental Data Card. Otherwise, data corruption can occur. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Warnings, Cautions & Notes CaUTIoN: Avoid areas on the radar display that appear “shadowed” (gray). The accuracy of the intensity of returns in the shaded areas should be treated as suspect. Exercise extreme caution, making maneuvering decisions with this information in mind. NoTE: All visual depictions contained within this document, including screen images of the system panel and displays, are subject to change and may not reflect the most current system and aviation databases. Depictions of equipment may differ slightly from the actual equipment. NoTE: Do not rely solely upon data link services to provide Temporary Flight Restric- tion (TFR) information. Always confirm TFR information through official sources such as Flight Service Stations or Air Traffic Control. NoTE: The United States government operates the Global Positioning System and is solely responsible for its accuracy and maintenance. The GPS system is subject to changes which could affect the accuracy and performance of all GPS equipment. Portions of the system utilize GPS as a precision electronic NAVigation AID (NAVAID). Therefore, as with all NAVAIDs, information presented by the system can be misused or misinterpreted and, therefore, become unsafe. NoTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NoTE: Use of polarized eyewear may cause the flight displays to appear dim or blank. NoTE: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This notice is being provided in accordance with California’s Proposition 65. If you have any questions or would like additional information, please refer to our web site at www.garmin.com/prop65. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Warnings, Cautions & Notes NoTE: Operating the system in the vicinity of metal buildings, metal structures, or electromagnetic fields can cause sensor differences that may result in nuisance mis- compare annunciations during start up, shut down, or while taxiing. If one or more of the sensed values are unavailable, the annunciation indicates no comparison is possible. NoTE: The system responds to a terminal procedure based on data coded within that procedure in the Navigation Database. Differences in system operation may be observed among similar types of procedures due to differences in the Navigation Database coding specific to each procedure. NoTE: The FAA has asked Garmin to remind pilots who fly with Garmin database- dependent avionics of the following: • It is the pilot’s responsibility to remain familiar with all FAA regulatory and advisory guidance and information related to the use of databases in the National Airspace System. • Garmin equipment will only recognize and use databases that are obtained from Garmin or Jeppesen. Databases obtained from Garmin or Jeppesen that have a Type 2 Letter of Authorization (LOA) from the FAA are assured compli- ance with all data quality requirements (DQRs). A copy of the Type 2 LOA is available for each applicable database and can be viewed at flygarmin.com by selecting ‘Aviation Database Declarations.’ • Use of a current Garmin or Jeppesen database in your Garmin equipment is required for compliance with established FAA regulatory guidance, but does not constitute authorization to fly any and all terminal procedures that may be presented by the system. It is the pilot’s responsibility to operate in accor- dance with established pertinent aircraft documents and regulatory guidance or limitations as applicable to the pilot, the aircraft, and installed equipment. NoTE: The pilot/operator must review and be familiar with Garmin’s database exclusion list as discussed in SAIB CE-14-04 to find what data may be incomplete. The database exclusion list can be viewed at flygarmin.com by selecting ‘Database Exclusions List.’ Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Warnings, Cautions & Notes NoTE: The pilot/operator must have access to Garmin and Jeppesen database alerts and consider their impact on the intended aircraft operation. The database alerts can be viewed at flygarmin.com by selecting ‘Aviation Database Alerts.’ NoTE: If the pilot/operator wants or needs to adjust the database, contact Garmin Product Support. NoTE: Garmin requests the flight crew report any observed discrepancies related to database information. These discrepancies could come in the form of an incorrect procedure; incorrectly identified terrain, obstacles and fixes; or any other displayed item used for navigation or communication in the air or on the ground. Go to flygarmin. com and select ‘Aviation Data Error Report’. NoTE: Electronic aeronautical charts displayed on this system have been shown to meet the guidance in AC 120-76D as a Type B Electronic Flight Bag (EFB) for FliteCharts® and ChartView™. The accuracy of the charts is subject to the chart data provider. Own-ship position on airport surface charts cannot be guaranteed to meet the accuracy specified in AC 120-76D. Possible additional requirements may make a secondary source of aeronautical charts, such as traditional paper charts or an additional electronic display, necessary on the aircraft and available to the pilot. If the secondary source of aeronautical charts is a Portable Electronic Device (PED), its use must be consistent with the guidance in AC 120-76D. NoTE: The navigation databases used in Garmin navigation systems contain Special Procedures. Before flying these procedures, pilots must have specific FAA authorization, training, and possession of the corresponding current, and legitimately-sourced chart (approach plate, etc.). Inclusion of the Special Procedure in the navigation database DOES NOT imply specific FAA authorization to fly the procedure. NoTE: Terrain and obstacle alerting is not available north of 89º North latitude and south of 89º South latitude. This is due to limitations present within the Terrain database and the system’s ability to process the data representing the affected areas. NoTE: The nose of the ‘own ship’ symbol represents the location of the aircraft. The center of any traffic symbol represents the location of that traffic. The traffic and own ship symbols are an abstract representation and do not reflect the physical extent of the aircraft/traffic, and should not replace other methods for identifying traffic. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Warnings, Cautions & Notes NoTE: The pilot/operator must review all portions of the flight plan following a flight plan import from any source. NoTE: When using Stormscope®, there are several atmospheric phenomena in addi- tion to nearby thunderstorms that can cause isolated discharge points in the strike display mode. However, clusters of two or more discharge points in the strike display mode do indicate thunderstorm activity if these points reappear after the screen has been cleared. NoTE: Intruder aircraft at or below 500 ft. AGL may not appear on the Garmin SVT display or may appear as a partial symbol. NoTE: Lamp(s) inside this product contain mercury (HG) and must be recycled or disposed of according to local, state, or federal laws. For more information, refer to our website at www.garmin.com/en-US/company/environment/recycling NoTE: Interference from GPS repeaters operating inside nearby hangars can cause an intermittent loss of attitude and heading displays while the aircraft is on the ground. Moving the aircraft more than 100 yards away from the source of the interference should alleviate the condition. NoTE: Operate the G1000® system power through at least one cycle in a period of four days of continuous operation to avoid an autonomous system reboot. NoTE: The purpose of this Cockpit Reference Guide is to provide the pilot a resource with which to find operating instructions on the major features of the system more easily. It is not intended to be a comprehensive operating guide. Complete operating procedures for the system are found in the Pilot’s Guide for this aircraft. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Warnings, Cautions & Notes Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Software License agreement SoFTWaRE LICENSE aGREEMENT BY USING THE DEVICE, COMPONENT OR SYSTEM MANUFACTURED OR SOLD BY GARMIN (“THE GARMIN PRODUCT”), YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY. Garmin Ltd. and its subsidiaries (“Garmin”) grants you a limited license to use the software embedded in the Garmin Product (the “Software”) in binary executable form in the normal operation of the Garmin Product. Title, ownership rights, and intellectual property rights in and to the Software remain with Garmin and/or its third-party providers. You acknowledge the Software is the property of Garmin and/or its third-party providers and is protected under the United States of America copyright laws and international copyright treaties. You further acknowledge the structure, organization, and code of the Software are valuable trade secrets of Garmin and/or its third-party providers and the Software in source code form remains a valuable trade secret of Garmin and/ or its third-party providers. You agree not to reproduce, decompile, disassemble, modify, reverse assemble, reverse engineer, or reduce to human readable form the Software or any part thereof or create any derivative works based on the Software. You agree not to export or re-export the Software to any country in violation of the export control laws of the United States of America. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Software License agreement Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Record of Revisions Record of Revisions Part Number Revision Date Page Range Description 190-00406-00 A 9/2004 All Initial Release B 10/2004 All Updated to new software revision number 190-00406-01 A 12/2004 All Added DME capability Added BRG1/BRG2 pointers Changed Airspeed Trend Vector Changed Altitude Trend Vector Added Checklist capability Added Flight ID capability B 1/2005 All Updated to new software revision number 190-00406-02 A 4/2005 All Reformatted manual to new format Added deicing capability Updated Annunciations and Alerts 190-00406-03 A 8/2005 All Added XM Weather capability Added TAWS-B Updated Message Advisories Added Lycoming engine parameters B 11/2005 All Changed System SW applicability to 0370.13 or later. Removed all references to the DA42L Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Record of Revisions Record of Revisions Part Number Revision Date Page Range Description 190-00406-04 A 12/2005 All Added TAS capability Various clerical changes B 3/2006 All Removed Ryan 9900BX Added Avidyne TAS600 Series Added Auxillary fuel tank note to EIS section Made various clerical changes 190-00406-05 A 10/2006 All Added GFC 700 Automatic Flight Control System Added GDU 6.13 parameters B 4/2007 All Added GWX 68 Color Weather Radar Added Check Gear message 190-00406-06 A 3/2008 All Added Airways, WAAS, VNAV & Charts Updated G1000 System Messages Removed GWX 68 Color Weather Radar Added other GDU 8.20 parameters Reformatted manual 190-00406-07 A 12/2009 All Added Synthetic Vision System Added Terrain-SVS Added other GDU 9.05 parameters B 01/2014 All Changed XM references to SiriusXM Added GWX 68 Airborne Color Weather Radar Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Record of Revisions Record of Revisions Part Number Revision Date Page Range Description 190-00406-08 A 03/2022 All Production Release for GDU 15.11 Updated WAAS Information Updated Database Information Added Smart Airspace® Updated Transponder Information Updated Traffic Information Updated Terrain Awareness Information Updated Approach Information Updated AFCS Information Added Bluetooth® Management Information Added Database Management Information Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A Record of Revisions Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A i Table of Contents FLIGHT INSTRUMENTS............................................................................................. 1 FLIGHT INSTRUMENTS ................................................................................................................ 1 airspeed Indicator ...................................................................................................................... 1 altimeter ...................................................................................................................................... 1 Horizontal Situation Indicator (HSI) ......................................................................................... 2 DME Information Window ......................................................................................................... 3 Course Deviation Indicator (CDI) .............................................................................................. 3 SUPPLEMENTaL FLIGHT DaTa ................................................................................................... 4 Generic Timer .............................................................................................................................. 4 outside air Temperature ............................................................................................................ 4 Wind Data .................................................................................................................................... 4 Synthetic Vision Technology (SVT) ............................................................................................ 5 PFD annunciations and alerting Functions.............................................................................. 6 ENGINE INDICaTIoN SySTEM (EIS) ................................................................... 7 EIS DISPLay.................................................................................................................................... 7 Engine Indicating System .......................................................................................................... 7 aUDIo aND CNS ....................................................................................................... 19 CoM oPERaTIoN ........................................................................................................................ 19 NaV oPERaTIoN ......................................................................................................................... 19 MoDE S TRaNSPoNDER ........................................................................................................... 21 aUDIo PaNEL PREFLIGHT PRoCEDURE ................................................................................ 21 FLIGHT MaNaGEMENT ......................................................................................... 23 USING MaP DISPLayS ............................................................................................................... 23 Map orientation........................................................................................................................ 23 Map Range................................................................................................................................. 24 Map Panning .............................................................................................................................. 24 Measuring Bearing and Distance ............................................................................................ 25 Topography ................................................................................................................................ 25 Map Display Symbols ............................................................................................................... 26 WayPoINTS .................................................................................................................................. 28 airports ...................................................................................................................................... 28 Non-airport and User Created Waypoints ............................................................................. 29 Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A ii Table of Contents aIRSPaCES .................................................................................................................................... 33 Smart airspace .......................................................................................................................... 34 FLIGHT PLaNNING...................................................................................................................... 34 Direct-To Navigation ................................................................................................................ 34 Flight Plan Display .................................................................................................................... 37 Creating a Basic Flight Plan..................................................................................................... 37 Flight Plan Waypoint and airway Modifications ................................................................... 38 Flight Plan Waypoint Constraints............................................................................................ 41 Flight Plan Vertical Navigation ............................................................................................... 43 Vertical Navigation Direct-To .................................................................................................. 44 Flight Plan operations.............................................................................................................. 44 Managing Flight Plans.............................................................................................................. 49 PRoCEDURES ............................................................................................................................... 56 Departures ................................................................................................................................. 57 arrivals ...................................................................................................................................... 59 approaches ............................................................................................................................... 61 TRIP PLaNNING........................................................................................................................... 69 RECEIVER aUToNoMoUS INTEGRITy MoNIToRING (RaIM) PREDICTIoN .................. 70 HaZaRD aVoIDaNCE ............................................................................................. 73 SIRIUSXM WEaTHER .................................................................................................................. 73 activating Services ................................................................................................................... 73 Using SiriusXM Weather Products .......................................................................................... 74 SToRMSCoPE LIGHTNING ........................................................................................................ 79 Setting Up Stormscope on the ‘MaP - NaVIGaTIoN MaP’ Page......................................... 79 aIRBoRNE CoLoR WEaTHER RaDaR .................................................................................... 80 Ground Mapping and Interpretation...................................................................................... 83 TERRaIN PRoXIMITy ................................................................................................................. 84 Displaying Terrain Proximity Data .......................................................................................... 84 ‘MaP-TERRaIN PRoXIMITy’ Page............................................................................................ 85 PRoFILE VIEW TERRaIN ............................................................................................................ 85 TERRaIN-SVT ............................................................................................................................... 86 Displaying Terrain-SVT Data .................................................................................................... 86 MaP-TERRaIN-SVS’ Page ......................................................................................................... 87 Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A iii Table of Contents TRaFFIC INFoRMaTIoN SERVICE (TIS).................................................................................. 88 Displaying TRaFFIC Data .......................................................................................................... 88 ‘MaP-TRaFFIC MaP’ Page ........................................................................................................ 89 TIS alerts .................................................................................................................................... 89 aVIDyNE TaS600 (TaS) (oPTIoNaL) ...................................................................................... 90 Displaying Traffic Data ............................................................................................................. 90 altitude Display ........................................................................................................................ 91 ‘MaP-TRaFFIC MaP’ Page Display Range .............................................................................. 91 TaS alerts ................................................................................................................................... 92 aUToMaTIC FLIGHT CoNTRoL SySTEM........................................................ 93 aFCS oVERVIEW ......................................................................................................................... 93 Basic autopilot operation ....................................................................................................... 93 FLIGHT DIRECToR oPERaTIoN................................................................................................ 94 activating the Flight Director ................................................................................................. 94 aFCS MoDES ............................................................................................................................... 95 Vertical Modes .......................................................................................................................... 95 Lateral Modes............................................................................................................................ 96 Combination Modes ................................................................................................................. 96 aDDITIoNaL FEaTURES ...................................................................................... 101 SaFETaXI .................................................................................................................................... 101 ELECTRoNIC CHaRTS (oPTIoNaL) ....................................................................................... 101 ChartView ................................................................................................................................ 102 FliteCharts ............................................................................................................................... 104 SIRIUSXM SaTELLITE RaDIo (oPTIoNaL) .......................................................................... 106 activating SiriusXM Satellite Radio Services ...................................................................... 106 Using SiriusXM Radio ............................................................................................................. 107 SCHEDULER ................................................................................................................................ 108 ELECTRoNIC CHECKLISTS (oPTIoNaL) ............................................................................... 109 BLUETooTH MaNaGEMENT .................................................................................................. 110 DaTaBaSE MaNaGEMENT ..................................................................................................... 111 PILoT PRoFILES ......................................................................................................................... 112 SCHEDULER ................................................................................................................................ 115 Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A iv Table of Contents aBNoRMaL oPERaTIoN .................................................................................... 117 Reversionary Mode ................................................................................................................. 117 abnormal GPS Conditions ..................................................................................................... 117 Garmin SVT Troubleshooting ................................................................................................. 118 SVT in Reversionary Mode ..................................................................................................... 118 Unusual attitudes ................................................................................................................... 118 SVT Unusual attitudes ............................................................................................................ 120 audio Panel Fail-Safe operation ........................................................................................... 120 Stuck Microphone ................................................................................................................... 120 CoM Tuning Failure ................................................................................................................. 120 Reversionary Mode ................................................................................................................. 121 Dead Reckoning ...................................................................................................................... 121 abnormal Radar Status annunciations ................................................................................ 121 Suspected autopilot Malfunction ......................................................................................... 122 overpowering autopilot Servos ........................................................................................... 122 Datalink Troubleshooting....................................................................................................... 122 aNNUNCIaTIoNS & aLERTS .............................................................................. 125 System annunciations ............................................................................................................ 125 Crew Profile Import/Export Messages ................................................................................. 126 FLIGHT PLaNNING.................................................................................................................... 127 Nearest airspace ..................................................................................................................... 127 Managing Flight Plans............................................................................................................ 127 RaDaR aNNUNCIaTIoNS........................................................................................................ 129 Radar Modes ........................................................................................................................... 129 antenna Stabilization annunciations ................................................................................... 129 TERRaIN/oBSTaCLE aNNUNCIaTIoNS ................................................................................ 129 Terrain-SVT alerts Summary .................................................................................................. 129 Terrain-SVT System Test Status annunciations ................................................................... 130 ‘MaP-TERRaIN-SVS’ Page Status annunciations................................................................. 130 TRaFFIC aNNUNCIaTIoNS ..................................................................................................... 131 TIS Failure annunciations ....................................................................................................... 131 TIS Modes ................................................................................................................................ 131 TIS Traffic Status annunciations ............................................................................................ 131 TaS Modes ............................................................................................................................... 132 Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A v Table of Contents TaS Failure annunciations...................................................................................................... 132 TaS Traffic Status annunciations ........................................................................................... 133 aFCS aLERTS .............................................................................................................................. 133 aFCS Status alerts .................................................................................................................. 133 CaS MESSaGES ......................................................................................................................... 134 Warning CaS Messages .......................................................................................................... 134 Caution CaS Messages ........................................................................................................... 135 advisory CaS Messages ......................................................................................................... 135 SySTEM aNNUNCIaTIoNS ...................................................................................................... 136 Message annunciations ......................................................................................................... 136 Voice alerts .............................................................................................................................. 136 SySTEM MESSaGE aDVISoRIES ........................................................................................... 136 aPPENDIX .................................................................................................................. 153 DaTaBaSE MaNaGEMENT ..................................................................................................... 153 Navigation Databases ............................................................................................................ 153 Dual Navigation Database Feature ..................................................................................... 154 Garmin Databases .................................................................................................................. 155 SoFTKEy MaPS ......................................................................................................................... 158 PFD Softkeys............................................................................................................................ 158 MFD Softkeys .......................................................................................................................... 161 FLIGHT MaNaGEMENT SyMBoLS........................................................................................ 162 PFD Navigation Status Box .................................................................................................... 162 Map Display Symbols ............................................................................................................. 163 Flight Planning ........................................................................................................................ 167 TERRaIN/oBSTaCLE SyMBoLS .............................................................................................. 169 Terrain Proximity ..................................................................................................................... 169 Profile View Terrain/obstacle Colors and Symbology ........................................................ 169 Terrain-SVT obstacle Colors and Symbology ...................................................................... 169 Terrain-SVT Potential Impact Point Symbols ...................................................................... 170 INDEX ...................................................................................................................... Index-1 INDEX ...................................................................................................................................... Index-1 Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A vi Table of Contents Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 1 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index FLIGHT INSTRUMENTS FLIGHT INSTRUMENTS aIRSPEED INDICaToR Changing Vspeeds and turning Vspeed bugs on/off: 1) Press the TMR/REF Softkey. 2) Turn the large FMS Knob to highlight the field of the desired Vspeed to be changed. 3) Turn the small FMS Knob to enter the desired value. When a speed has been changed from a default value, an asterisk appears next to the speed. 4) Press the ENT Key or turn the large FMS Knob to highlight the ON/OFF field. 5) Turn the small FMS Knob clockwise to ON or counterclockwise to OFF. 6) To remove the window, press the CLR Key or the TMR/REF Softkey. Turning all Vspeed bugs on/off: 1) Press the TMR/REF Softkey. 2) Press the MENU Key. 3) To activate all Vspeed bugs, press the ENT Key with All References On highlighted. 4) To remove all Vspeed bugs, turn the FMS Knob to highlight All References Off and press the ENT Key. Restoring all Vspeed defaults: 1) Press the TMR/REF Softkey. 2) Press the MENU Key. 3) Turn the FMS Knob to highlight Restore Defaults and press the ENT Key. aLTIMETER Setting the Selected altitude: Turn the aLT Knob to set the Selected Altitude (large knob for 1000-ft increments, small knob for 100-ft increments. If set, the Minimum Descent Altitude/Decision Height (MDA/DH) value is also available for the Selected Altitude. Displaying altitude in meters: 1) Press the PFD Softkey to display the second-level softkeys. 2) Press the aLT UNIT Softkey. 3) Press the METERS Softkey to turn on metric altitude displays. 4) Press the BaCK Softkey to return to the top-level softkeys. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 2 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Selecting the altimeter barometric pressure setting: Turn the BaRo Knob to select the desired setting. Selecting standard barometric pressure (29.92 in Hg): 1) Press the PFD Softkey to display the second-level softkeys.. 2) Press the STD BaRo Softkey; STD BARO is displayed in barometric setting box. Changing altimeter barometric pressure setting units: 1) Press the PFD Softkey to display the second-level softkeys. 2) Press the aLT UNIT Softkey. 3) Press the IN Softkey to display the barometric pressure setting in inches of mercury (in Hg). Or, press the HPa Softkey to display the barometric pressure setting in hectopascals (hPa). 4) Press the BaCK Softkey to return to the top-level softkeys. HoRIZoNTaL SITUaTIoN INDICaToR (HSI) Changing the HSI display format: 1) Press the PFD Softkey 2) Press the HSI FRMT Softkey. 3) Press the 360 HSI or aRC HSI Softkey. adjusting the selected heading: Turn the HDG Knob to set the selected heading. Push the HDG Knob to synchronize the bug to the current heading. adjusting the Selected Course: Turn the CRS Knob to set the Selected Course. Push the CRS Knob to re-center the CDI and return the course pointer to the bearing of the active waypoint or navigation station. Changing the navigation angle true/magnetic setting: 1) Use the FMS Knob to select the ‘AUX - SYSTEM SETUP’ Page on the MFD. 2) Push the FMS Knob to activate the cursor. 3) Turn the large FMS Knob to highlight Nav Angle in the Display Units box. 4) Turn the small FMS Knob to highlight the desired setting and press the ENT Key. • TRUE - References angles to true north (T) • MAGNETIC - Angles corrected to the computed magnetic variation (Mag Var) Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 3 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Bearing Pointers and Information Windows Selecting bearing display and changing sources: 1) Press the PFD Softkey. 2) Press a BRG Softkey to display the desired bearing pointer and information window with a NAV source. 3) Press the BRG Softkey again to change the bearing source to GPS. 4) Press the BRG Softkey again to change the bearing source to ADF. 5) To remove the bearing pointer and information window, press the BRG Softkey again. DME INFoRMaTIoN WINDoW Displaying the DME Information Window: 1) Press the PFD Softkey. 2) Press the DME Softkey to display the DME Information Window. 3) To remove the DME Information Window, press the DME Softkey again. CoURSE DEVIaTIoN INDICaToR (CDI) Changing navigation sources: 1) Press the CDI Softkey to change from GPS to VOR1 or LOC1. This places the cyan tuning box over the NAV1 standby frequency in the upper left corner of the PFD. 2) Press the CDI Softkey again to change from VOR1 or LOC1 to VOR2 or LOC2. This places the cyan tuning box over the NAV2 standby frequency. 3) Press the CDI Softkey a third time to return to GPS. Changing the selected GPS CDI setting: 1) Use the FMS Knob to select the ‘AUX - SYSTEM SETUP’ Page on the MFD. 2) Push the FMS Knob to activate the cursor. 3) Turn the large FMS Knob to highlight Selected in the GPS CDI box. 4) Turn the small FMS Knob to highlight the desired setting and press the ENT Key. 5) To cancel the selection, push the FMS Knob or press the CLR Key. Enabling/disabling oBS Mode while navigating a GPS flight plan: 1) Press the oBS Softkey to select OBS Mode. 2) Turn the CRS Knob to select the desired course to/from the waypoint. Push the CRS Knob to synchronize the Selected Course with the bearing to the next waypoint. 3) Press the oBS Softkey again to return to automatic waypoint sequencing. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 4 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index SUPPLEMENTaL FLIGHT DaTa GENERIC TIMER Using the Generic Timer: 1) Press the TMR/REF Softkey. 2) Turn the large FMS Knob to select the timer field (HH:MM:SS). 3) Use the small FMS Knob to enter the desired time. 4) Press the ENT Key. The UP/DN field is now highlighted. 5) Turn the small FMS Knob to display the ‘UP/DN’ Window. 6) Turn the small FMS Knob to select ‘UP’ or ‘DN’. 7) Press the ENT Key. ‘START?’ is now highlighted. 8) Press the ENT Key to start the timer. The field changes to ‘STOP?’. If the timer is counting down, it will start counting up after reaching zero. 9) To stop the timer, press the ENT Key with ‘STOP?’ highlighted. The field changes to ‘RESET?’. 10) To reset the timer, press the ENT Key with ‘RESET?’ highlighted. The field changes back to ‘START?’ and the digits are reset. 11) To remove the window, press the CLR Key or the TMR/REF Softkey. oUTSIDE aIR TEMPERaTURE Changing temperature display units: 1) Select the ‘AUX - SYSTEM SETUP’ Page on the MFD using the FMS Knob. 2) Push the FMS Knob to activate the cursor. 3) Turn the large FMS Knob to highlight the TEMP field in the Display Units box. 4) Turn the small FMS Knob to highlight either ‘CELSIUS (°C)’ or ‘FAHRENHEIT (°F)’ and press the ENT Key to confirm the selection. 5) To cancel the selection, push the FMS Knob or press the CLR Key. WIND DaTa Displaying wind data: 1) Press the PFD Softkey. 2) Press the WIND Softkey to display wind data below the selected heading. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 5 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 3) Press one of the oPTN Softkeys to change how wind data is displayed: • oPTN 1: Wind direction arrows with numeric headwind or tailwind and crosswind components • oPTN 2: Wind direction arrow and numeric speed • oPTN 3: Total wind direction arrow with numeric headwind or tailwind and crosswind speed components 4) To remove the window, press the oFF Softkey. SyNTHETIC VISIoN TECHNoLoGy (SVT) WaRNING: Use appropriate primary systems for navigation, and for terrain, obstacle, and traffic avoidance. SVT is intended as an aid to situational awareness only and may not provide either the accuracy or reliability upon which to solely base decisions and/or plan maneuvers to avoid terrain, obstacles, or traffic. activating and deactivating SVT: 1) Press the PFD Softkey. 2) Press the SyN VIS Softkey. 3) Press the SyN TERR Softkey. The SVT display will cycle on or off with the SyN TERR Softkey. activating and deactivating Pathways: 1) Press the PFD Softkey. 2) Press the SyN VIS Softkey. 3) Press the PaTHWay Softkey. The Pathway feature will cycle on or off with the PaTHWay Softkey. activating and deactivating Horizon Headings: 1) Press the PFD Softkey. 2) Press the SyN VIS Softkey. 3) Press the HRZN HDG Softkey. The horizon heading display will cycle on or off with the HRZN HDG Softkey. activating and deactivating airport Signs: 1) Press the PFD Softkey. 2) Press the SyN VIS Softkey. 3) Press the aPTSIGNS Softkey. Display of airport signs will cycle on or off with the aPTSIGNS Softkey. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 6 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Configuring field of view: 1) While viewing the ‘MAP - NAVIGATION MAP’ Page, press the MENU Key to display the ‘PAGE MENU’. 2) Turn the large FMS Knob to highlight Map Setup and press the ENT Key. 3) Turn the FMS Knob to select the Map Group and press the ENT Key. 4) Turn the large FMS Knob to scroll through the Map Group options to FIELD OF VIEW. 5) Turn the small FMS Knob to select On or Off. 6) Push the FMS Knob to return to the ‘MAP - NAVIGATION MAP’ Page. PFD aNNUNCIaTIoNS aND aLERTING FUNCTIoNS Setting the Minimum Descent altitude/Decision Height and bug: 1) Press the TMR/REF Softkey. 2) Turn the large FMS Knob to highlight the Minimums field. 3) Turn the small FMS Knob to select the desired altitude source: barometric (BARO) or temperature compensated (TEMP COMP). OFF is selected by default. Press the ENT Key or turn the large FMS Knob to highlight the next field. 4) Use the small FMS Knob to enter the desired altitude for minimums. 5) If using temperature compensated (TEMP COMP), use the small FMS Knob to enter destination air temperature. 5) To remove the window, press the CLR Key or the TMR/REF Softkey. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 7 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index ENGINE INDICaTIoN SySTEM (EIS) EIS DISPLay ENGINE INDICaTING SySTEM The Engine Indicating System (EIS) displays all engine, fuel, electrical, fuel calculation, and ice protection (optional) information. Level 1 Level 2 Level 3 Description ENGINE Displays Engine indication information and additional softkeys. SySTEM Displays Engine System indication information. FUEL Displays Engine Fuel indication information and additional softkeys DEC FUEL Decreases displayed fuel remaining in 1-gal increments. INC FUEL Increases displayed fuel remaining in 1-gal increments. RST FUEL Resets displayed fuel remaining to maximum fuel capacity for aircraft and fuel used to zero. BaCK Returns to Engine indication information and additional softkeys. EIS Softkeys Map Engine Display NoTE: Refer to the current version of the pertinent flight manual for specific values and operating limitations. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 8 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Engine Display 1 2 3 4 5 6 7 8 Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 9 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 1 Engine Load Indicator (LOAD %) Displays current engine loads as percentages. 2 Tachometer (RPM) Displays propeller speeds in revolutions per minute (rpm). The green band indicates the normal operating range. The red band indicates the warning range. If the indicated rpm is in the warning range, the ‘RPM’ and the digital indication will flash red and white. NOTE: RPM information is provided by the FADEC. 3 Fuel Flow Indicator (FUEL FLOW GPH) Displays fuel flow for each engine in gallons per hour (gph). 4 Oil Temperature Indicator (OIL TEMP) Displays engine oil temperature ranges. The green band indicates the normal operating range. The amber bands indicate the cautionary ranges. If the indicated temperature is in the cautionary range, the ‘OIL TEMP’ and the ‘L’ or ‘R’ arrow indicator will display solid amber and black. The red bands indicate the warning ranges. If the indicated temperature is in the warning range, the ‘OIL TEMP’ will flash red and white and the ‘L’ or ‘R’ arrow indicator will display solid red and white. 5 Oil Pressure Indicator (OIL PRES) Displays engine oil pressure ranges. The green band indicates the normal operating range. The amber bands indicate the cautionary ranges. If the indicated pressure is in the cautionary range, the ‘OIL PRES’ and the ‘L’ or ‘R’ arrow indicator will display solid amber and black. The red bands indicate the warning ranges. If the indicated temperature is in the warning range, the ‘OIL PRES’ will flash red and white and the ‘L’ or ‘R’ arrow indicator will display solid red and white. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 10 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 6 Coolant Temperature Indicator (COOLANT TEMP) Displays coolant temperature ranges. The green band indicates the normal operating range. The amber bands indicate the cautionary ranges. If the indicated temperature is in the cautionary range, the ‘COOLANT TEMP’ and the ‘L’ or ‘R’ arrow indicator will display solid amber and black. The red bands indicate the warning ranges. If the indicated temperature is in the warning range, the ‘COOLANT TEMP’ will flash red and white and the ‘L’ or ‘R’ arrow indicator will display solid red and white. 7 Fuel Temperature Indicator (FUEL TEMP) Displays fuel temperature ranges. The green band indicates the normal operating range. The amber bands indicate the cautionary ranges. If the indicated temperature is in the cautionary range, the ‘FUEL TEMP’ and the ‘L’ or ‘R’ arrow indicator will display solid amber and black. The red bands indicate the warning ranges. If the indicated temperature is in the warning range, the ‘FUEL TEMP’ will flash red and white and the ‘L’ or ‘R’ arrow indicator will display solid red and white. 8 Fuel Quantity Indicator (FUEL QTY GAL) Displays the fuel quantity in each tank in gallons (gal). The green band indicates the normal operating range. The red band indicates the warning range. If the indicated quantity is in the warning range, the ‘FUEL QTY GAL’ will flash red and white and the ‘L’ or ‘R’ arrow indicator will display solid red and white. System Display accessing the EIS System Display: 1) Press the ENGINE Softkey. 2) Press the SySTEM Softkey. 3) To return to the default Engine Display, press the ENGINE or BaCK Softkey. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 11 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index System Display 1 2 3 4 5 6 7 8 9 Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 12 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 1 Engine Load Indicator (LOAD %) Displays current engine loads as percentages. 2 Tachometer (RPM) Displays propeller speeds in revolutions per minute (rpm). The green band indicates the normal operating range. The red band indicates the warning range. If the indicated rpm is in the warning range, the ‘RPM’ and the digital indication will flash red and white. NOTE: RPM information is provided by the FADEC. 3 Voltmeter (VOLTS) Displays the primary bus voltage. The green band indicates the normal operating range. The amber bands indicate the cautionary range. If the indicated voltage is in the cautionary range, the ‘VOLTS’, the digital indication, and the ‘L’ or ‘R’ arrow indicator will display solid amber and black. The red band indicates the warning range. If the indicated voltage is in the warning range, the ‘VOLTS’ and the digital indication will flash red and white, and the ‘L’ or ‘R’ arrow indicator will display solid red and white. 4 Ammeter (AMPS) Displays each alternator load in amperes (amps). The green band indicates the normal operating range. The red band indicates the warning range. If the indicated amperes is in the warning range, the ‘AMPS’ and the digital indication will flash red and white, and the ‘L’ or ‘R’ arrow indicator will display solid red and white. 5 Gearbox Temperature Indicator (GEARBOX °C) Displays the temperature of each gearbox in degrees Celsius (°C). The green band indicates the normal operating range. The amber bands indicate the cautionary ranges. If the indicated pressure is in the cautionary range, the ‘GEARBOX °C’, digital indication, and the ‘L’ or ‘R’ arrow indicator will display solid amber and black. The red bands indicate the warning ranges. If the indicated temperature is in the warning range, the ‘GEARBOX °C’ and digital indication will flash red and white, and the ‘L’ or ‘R’ arrow indicator will display solid red and white. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 13 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 6 Coolant Temperature Indicator (COOLANT °C) Displays the coolant temperature of each side in °C. White digital indications display the normal operating range. If the indicated temperature is in the cautionary range, the ‘COOLANT °C’ and the digital indication will display solid amber and black. If the indicated temperature is in the warning range, the ‘COOLANT °C’ and the digital indication will flash red and white. 7 Oil Temperature Indicator (OIL °C) Displays oil temperature in °C. White digital indications display the normal operating range. If the indicated temperature is in the cautionary range, the ‘°C’ and the digital indication will display solid amber and black. If the indicated temperature is in the warning range, the ‘°C’ and the digital indication will flash red and white. 8 Oil Pressure Indicator (OIL BAR) Displays oil pressure in bars. White digital indications display the normal operating range. If the indicated pressure is in the cautionary range, the ‘BAR’ and the digital indication will display solid amber and black. If the indicated pressure is in the warning range, the ‘BAR’ and the digital indication will flash red and white. 9 Deice Fluid Indicator (DEICE FLUID) (Optional) Displays the quantity of deice fluid; tick marks are located at quarter intervals. The green band indicates the normal operating range. If the indication is in the warning range, the ‘DEICE FLUID’ and the arow indicator will flash red and white. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 14 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Fuel Display NoTE: Fuel calculations do not use the aircraft fuel quantity indicators and are calculated from the last time the fuel was reset. NoTE: If optional auxiliary fuel tanks are installed, the fuel remaining can be adjusted up to a maximum of 76.4 gal; the Fuel Quantity Indicator does not account for fuel in the auxiliary tanks. accessing the EIS Fuel Display: 1) Press the ENGINE Softkey. 2) Press the FUEL Softkey. 3) To return to the default Engine Display, press the ENGINE or BaCK Softkey. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 15 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Fuel Display 1 2 3 4 5 6 7 8 9 10 Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 16 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 1 Engine Load Indicator (LOAD %) Displays current engine loads as percentages. 2 Tachometer (RPM) Displays propeller speeds in revolutions per minute (RPM). The green band indicates the normal operating range. The red band indicates the warning range. If the indicated rpm is in the warning range, the ‘RPM’ and the digital indication will flash red and white. NOTE: RPM information is provided by the FADEC. 3 Fuel Quantity Indicator (FUEL GAL) Displays fuel in each tank in gallons (GAL). White digital indications display the normal operating range. If the indicated quantity is in the warning range, the digital indication and ‘GAL’ will flash red and white. 4 Fuel Flow Indicator (FUEL GPH) Displays fuel flow for each engine in gallons per hour (GPH). 5 Fuel Temperature Indicator (FUEL °C) Displays fuel temperature for each tank in degrees Celsius (°C). White digital indications display the normal operating range. If the indicated temperature is in the cautionary range, the ‘°C’ and the digital indication will display solid amber and black. If the indicated temperature is in the warning range, the ‘°C’ and the digital indication will flash red and white. 6 Set Fuel Remaining (GAL REM) Displays current fuel remaining (GAL) as set by the pilot and adjusted for fuel burn since last set. 7 Calculated Fuel Used (GAL USED) Displays quantity of fuel used (GAL) based on fuel flow since last reset. 8 Calculated Endurance (ENDUR) Displays flight time remaining (HH:MM) based on the calculated fuel remaining. 9 Calculated Range (RANGE NM) Displays aircraft range in nautical miles (NM) based on the calculated fuel remaining. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 17 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 10 Total Time in Service (TTL TIME IN SVC) Displays the aircraft’s total flight hours (HRS); activated when the aircraft becomes airborne. Fuel CalCulations NoTE: Fuel calculations do not use the aircraft fuel quantity indicators and are calculated from the last time the fuel was reset. NoTE: The Fuel Quantity Indicator shows 25 gallons per side when full. Fuel calculations are based on the fuel flow totalizer and the displayed fuel remaining (GAL REM), adjusted by the pilot using the following softkeys: adjusting the fuel totalizer quantity: From the Fuel Display, press the DEC FUEL or INC FUEL Softkey to obtain the desired number of gallons remaining (GAL REM). Resetting the fuel totalizer: From the Fuel Display, press the RST FUEL Softkey. This also resets the displayed fuel remaining (GAL REM) to zero. Enabling/disabling the Fuel Range Ring and selecting a reserve fuel time: 1) Display the ‘MAP - NAVIGATION MAP’ Page (press and hold the CLR Key for 2 seconds to quickly select this map). 2) Press the MENU Key. 3) Highlight ‘Map Setup’ and press the ENT Key. The ‘MAP SETUP’ Menu is displayed. 4) Use the small FMS Knob to select the ‘Map’ group and press the ENT Key. 5) Highlight the ‘FUEL RNG (RSV)’ Field. 6) Turn the small FMS Knob to select ‘On’ or ‘Off’. 7) Turn the large FMS Knob to highlight the reserve fuel time, how long the aircraft can fly after reaching the reserve fuel. 8) Enter the desired reserve fuel time (00+00 to 23+59; hours+minutes) and press the ENT Key. 9) Press the FMS Knob to return to the ‘MAP - NAVIGATION MAP’ Page. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 18 Engine Indication System Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 19 audio and CNS Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index aUDIo aND CNS CoM oPERaTIoN Manually tuning a CoM frequency: 1) Turn the CoM Knob to tune the desired frequency in the ‘COM TUNING’ Box (large knob for MHz; small knob for kHz). 2) Press the Frequency Transfer Key to transfer the frequency to the active field. 3) Adjust the volume level with the COM VoL/SQ Knob. 4) Push the COM VoL/SQ Knob to turn automatic squelch on and off. auto-tuning a CoM frequency for a nearby airport from the PFD: 1) Press the NRST Softkey on the PFD to open the ‘NEAREST AIRPORTS’ Window. A list of 25 nearest airport identifiers and COM frequencies is displayed. 2) Turn the FMS Knob to scroll through the list and highlight the desired COM frequency. 3) Press the ENT Key to load the COM frequency into the COM Standby Tuning Box. 4) Press the Frequency Transfer Key to transfer the frequency to the COM Active Frequency Field. auto-tuning a CoM frequency from the WPT and NRST Pages: 1) From any page the COM frequency can be auto-tuned, activate the cursor by pushing the FMS Knob or pressing the appropriate softkey. 2) Turn the FMS Knob to place the cursor on the desired COM frequency. 3) Press the ENT Key to load the COM frequency into the standby field of the selected COM radio. 4) Press the Frequency Transfer Key to transfer the frequency to the COM Active Frequency Field. Changing CoM frequency channel spacing: 1) Select the ‘AUX – SYSTEM SETUP’ Page. 2) Push the FMS Knob to activate the flashing cursor. 3) Turn the large FMS Knob to highlight the Channel Spacing Field in the ‘COM CONFIG’ Box. 4) Turn the small FMS Knob to select the desired channel spacing. 5) Press the ENT Key to complete the channel spacing selection. NaV oPERaTIoN Manually tuning a NaV frequency: 1) Turn the NaV Knob to tune the desired frequency in the NAV Tuning Box. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 20 audio and CNS Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 2) Press the Frequency Transfer Key to transfer the frequency to the NAV Active Frequency Field. 3) Adjust the volume level with the NAV VoL/ID Knob. 4) Push the NAV VoL/ID Knob to turn the Morse code identifier audio on and off. auto-tuning a NaV frequency from the WPT and NRST Pages: 1) From any page the NAV frequency can be auto-tuned, activate the cursor by pushing the FMS Knob or the appropriate softkey. 2) Turn the large FMS Knob to place the cursor on the desired NAV identifier or NAV frequency. 3) On the ‘WPT - VOR INFORMATION’ and ‘NRST - NEAREST AIRPORTS’ pages, press the FREQ Softkey to place the cursor on the NAV frequency. 4) Press the ENT Key to load the NAV frequency into the standby field of the selected NAV radio. 5) Press the Frequency Transfer Key to transfer the frequency to the NAV Active Frequency Field.Tuning an aDF frequency: 1) Press the aDF/DME Softkey to display the ‘ADF/DME TUNING’ Window. 2) Turn the large FMS Knob to place the selection cursor over the standby ADF frequency field. 3) Turn the small FMS Knob to begin data entry and change each digit. 4) Turn the large FMS Knob to move the cursor to the next digit position. 5) Press the ENT Key to complete data entry for the standby frequency. Transferring the active and standby aDF frequencies: 1) Turn the large FMS Knob to place the selection cursor over the standby ADF frequency field. 2) Press the ENT Key to complete the frequency transfer. Selecting an aDF receiver mode: 1) Turn the large FMS Knob to place the selection cursor over the ADF mode field. 2) Turn the small FMS Knob to select the desired ADF receiver mode. adjusting aDF receiver volume: 1) Turn the large FMS Knob to place the selection cursor over the ADF volume field. 2) Turn the small FMS Knob to adjust volume as desired. Selecting DME transceiver pairing: 1) Press the aDF/DME Softkey to display the ‘ADF/DME TUNING’ Window. 2) Turn the small FMS Knob to select the DME tuning mode. 3) Press the ENT Key to complete the selection. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 21 audio and CNS Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index MoDE S TRaNSPoNDER Selecting a transponder mode: 1) Press the XPDR Softkey to display the Transponder Mode Selection Softkeys. 2) Press the desired softkey to activate the transponder mode. Entering a transponder code with softkeys: 1) Press the XPDR Softkey to display the Transponder Mode Selection Softkeys. 2) Press the CoDE Softkey to display the Transponder Code Selection Softkeys, for digit entry. 3) Press the digit softkeys to enter the code in the code field. When entering the code, the next softkey in sequence must be pressed within 10 seconds, or the entry is cancelled and restored to the previous code. Pressing the BKSP Softkey moves the code selection cursor to the previous digit. Five seconds after the fourth digit has been entered, the transponder code becomes active. Entering a transponder code with the PFD FMS Knob: 1) Press the XPDR and the CoDE Softkeys as in the previous procedure to enable code entry. 2) Turn the small FMS Knob on the PFD to enter the first two code digits. 3) Turn the large FMS Knob to move the cursor to the next code field. 4) Enter the last two code digits with the small FMS Knob. 5) Press the ENT Key to complete code digit entry. Entering a Flight ID: 1) Press the TMR/REF Softkey to display the ‘REFERENCES’ Window. 2) Push the FMS Knob to activate the selection cursor, if not already activated. 3) Turn the large FMS Knob to scroll down to the Flight ID. 4) Turn the small FMS Knob to enter the desired Flight ID. 5) Press the ENT Key to complete Flight ID entry. aUDIo PaNEL PREFLIGHT PRoCEDURE Setting the audio Panel during preflight: 1) Verify the PILOT and COPLT Annunciations are extinguished. 2) Verify manual squelch is set to full open. 3) Turn the PILoT/PaSS Knobs clockwise two full turns. This sets the intercom level to max volume (least amount of attenuation). 4) Adjust radio volume levels (COM, NAV) to a suitable level. 5) Adjust the PILoT/PaSS Knob volume to the desired intercom level. 6) Reset squelch to automatic, or adjust to the appropriate level manually. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 22 audio and CNS Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Blank Page Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 23 Flight Management Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index FLIGHT MaNaGEMENT Changing a field in the MFD Navigation Data Bar: 1) Select the ‘AUX – SYSTEM SETUP ’ Page. 2) Push the FMS Knob momentarily to activate the flashing cursor. 3) Turn the large FMS Knob to highlight the desired field number in the ‘MFD DATA BAR FIELDS’ Box. 4) Turn the small FMS Knob to display and scroll through the data options list to select the desired data. 5) Press the ENT Key. Pressing the DFLTS Softkey returns all fields to the default setting. USING MaP DISPLayS MaP oRIENTaTIoN Changing the orientation for map displays: 1) With the ‘MAP – NAVIGATION MAP’ Page displayed, press the MENU Key. The cursor flashes on the ‘Map Setup’ option. 2) Press the ENT Key to display the ‘MAP SETUP’ Window. 3) Select the ‘Map’ Group. 4) Press the ENT Key. 5) Turn the small FMS Knob to select the desired orientation. 6) Press the ENT Key to select the new orientation. 7) Push the FMS Knob to return to the base page. Enabling/disabling auto North Up and selecting the minimum switching range: 1) With the ‘MAP – NAVIGATION MAP’ Page displayed, press the MENU Key. The cursor flashes on the ‘Map Setup’ option. 2) Press the ENT Key to display the ‘MAP SETUP’ Window. 3) Select the ‘Map’ Group. 4) Press the ENT Key. 5) Highlight the ‘AUTO NORTH UP’ Field. 6) Select ‘On’ or ‘Off’ using the small FMS Knob. 7) Press the ENT Key to accept the selected option. The flashing cursor highlights the Range Field. 8) Use the small FMS Knob to select the desired range. 9) Press the ENT Key to accept the selected option. 10) Push the FMS Knob to return to the ‘MAP – NAVIGATION MAP’ Page. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 24 Flight Management Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index MaP RaNGE Configuring automatic zoom: 1) Press the MENU Key with the ‘MAP – NAVIGATION MAP’ Page displayed. The cursor flashes on the ‘Map Setup’ option. 2) Press the ENT Key. The ‘MAP SETUP’ Window is displayed. 3) Turn the small FMS Knob to select the ‘Map’ Group. 4) Press the ENT Key. 5) Turn the large FMS Knob to highlight the ‘AUTO ZOOM’ On/Off Field, and select ‘Off’ or ‘On’ using the small FMS Knob. 6) Press the ENT Key to accept the selected option. The flashing cursor highlights the ‘AUTO ZOOM’ display selection Field. 7) Select ‘MFD’, ‘PFD’, or ‘ALL’ using the small FMS Knob. 8) Press the ENT Key to accept the selected option. The flashing cursor highlights the ‘MAX LOOK FWD’ Field. Times are from zero to 999 minutes. 9) Use the FMS Knob to set the time. Press the ENT Key. 10) Repeat Step 9 for ‘MIN LOOK FWD’ (zero to 99 minutes) and ‘TIME OUT’ (zero to 99 minutes). 11) Push the FMS Knob to return to the ‘MAP – NAVIGATION MAP’ Page. MaP PaNNING Panning the map: 1) With the desired map display shown on the MFD, push the Joystick to display the Map Pointer. 2) Move the Joystick to move the Map Pointer around the map. 3) Push the Joystick to remove the Map Pointer and recenter the map on the aircraft’s current position. Reviewing information for an airport, NaVaID, or user waypoint: 1) With the desired map display shown on the MFD, push the Joystick to display the Map Pointer and place the Map Pointer on a waypoint. 2) Press the ENT Key to display the information page for the selected waypoint. 3) Press the Go BaCK Softkey, the CLR Key, or the ENT Key to exit the information page and return to the ‘MAP – NAVIGATION MAP’ Page. Reviewing information for a special-use or controlled airspace: 1) With the desired map display shown on the MFD, push the Joystick to display the Map Pointer. Place the Map Pointer on the boundary of an airspace. Information about the airspace is displayed on the map next to the map pointer. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 25 Flight Management Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 2) Push the Joystick to remove the Map Pointer and center the map on the aircraft. or: 1) With the desired map display shown on the MFD, push the Joystick to display the Map Pointer and place the Map Pointer on an open area within the boundaries of an airspace. 2) Press the ENT Key to display an options menu. 3) ‘Review Airspaces’ should already be highlighted, if not select it. Press the ENT Key to view information for the airspace. 4) Push the FMS Knob, or press the CLR or ENT Key to return to the map display. MEaSURING BEaRING aND DISTaNCE Measuring bearing and distance between any two points: 1) Press the MENU Key (with the ‘MAP – NAVIGATION MAP’ Page displayed). 2) Use the FMS Knob to highlight the ‘Measure Bearing/Distance’ Field. 3) Press the ENT Key. A Measure Pointer is displayed on the map at the aircraft’s present position. 4) Move the Joystick to place the reference pointer at the desired location. The bearing and distance are displayed at the top of the map. Elevation at the current pointer position is also displayed. Pressing the ENT Key changes the starting point for measuring. 5) To exit the Measure Bearing/Distance option, push the Joystick; or select ‘Stop Measuring’ from the ‘PAGE MENU’ Window and press the ENT Key. ToPoGRaPHy Displaying/removing topographic data on MFD map displays: 1) Press the MaP Softkey on the ‘MAP – NAVIGATION MAP’ Page. 2) Press the ToPo Softkey. 3) Press the ToPo Softkey again to remove topographic data from the Navigation Map. When topographic data is removed from the page, all navigation data is presented on a black background. Displaying/removing topographic data on the Inset Map: 1) Press the INSET Softkey. 2) Press the ToPo Softkey. 3) Press the ToPo Softkey again to remove topographic data from the Inset Map. When topographic data is removed from the page, all navigation data is presented on a black background. Selecting a topographical data range: 1) Press the MENU Key with the ‘MAP – NAVIGATION MAP’ Page displayed. The cursor flashes on the ‘Map Setup’ option. 2) Press the ENT Key. The ‘MAP SETUP’ Window is displayed. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 26 Flight Management Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 3) Turn the small FMS Knob to select the ‘Map’ Group. 4) Press the ENT Key. 5) Use the large FMS Knob to highlight the TERRAIN DATA Range Field. Ranges are from 500 FT to 2000 nm. 6) To change the TERRAIN DATA Range setting, turn the small FMS Knob to display the range list. 7) Select the desired range using the small FMS Knob. 8) Press the ENT Key. 9) Push the FMS Knob to return to the ‘MAP – NAVIGATION MAP’ Page. Displaying/removing the topographic data scale: 1) Press the MENU Key with the ‘MAP – NAVIGATION MAP’ Page displayed. The cursor flashes on the ‘Map Setup’ option. 2) Press the ENT Key. The ‘MAP SETUP’ Window is displayed. 3) Turn the small FMS Knob to select the ‘Map’ Group and press the ENT Key. 4) Turn the large FMS Knob to highlight the ‘TOPO SCALE’ Field. 5) Turn the small FMS Knob to select ‘On’ or ‘Off’. Press the ENT Key. 6) Push the FMS Knob to return to the ‘MAP – NAVIGATION MAP’ Page. Displaying/removing Profile View: 1) Press the MaP Softkey on the ‘MAP – NAVIGATION MAP’ Page. 2) Press the PRoFILE Softkey to enable or disable Profile View. or: 1) Press the MENU Key. 2) Select ‘Show Profile View’ or ‘Hide Profile View’ and press the ENT Key. MaP DISPLay SyMBoLS Symbol Setup Setting up the ‘Land’, ‘aviation’, or ‘airways’ Group items: 1) Press the MENU Key with the ‘MAP – NAVIGATION MAP’ Page displayed. The cursor flashes on the ‘Map Setup’ option. 2) Press the ENT Key. The ‘MAP SETUP’ Window is displayed. 3) Turn the small FMS Knob to select the desired group. 4) Press the ENT Key. The cursor flashes on the first field. 5) Turn the large FMS Knob to select the desired option. 6) Turn the small FMS Knob to select the desired setting (e.g. On/Off or maximum range). 7) Press the ENT Key to accept the selected option and move the cursor to the next item. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 27 Flight Management Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 8) Repeat Steps 5 through 7 as necessary. 9) Push the FMS Knob to return to the ‘MAP – NAVIGATION MAP’ Page. Displaying/removing airways: 1) Press the MaP Softkey with the ‘MAP – NAVIGATION MAP’ Page displayed. 2) Press the aIRWayS Softkey. Both High and Low Altitude Airways are displayed (AIRWY On). 3) Press the softkey again to display Low Altitude Airways only (AIRWY LO). 4) Press the softkey again to display High Altitude Airways only (AIRWY HI). 5) Press the softkey again to remove High Altitude Airways. No airways are displayed. Selecting an airway range: 1) Press the MENU Key with the ‘MAP – NAVIGATION MAP’ Page displayed. The cursor flashes on the ‘Map Setup’ option. 2) Press the ENT Key. The ‘MAP SETUP’ Window is displayed. 3) Turn the small FMS Knob to select the ‘Airways’ Group, and press the ENT Key. 4) Turn the large FMS Knob to highlight the LOW ALT AIRWAY Range Field or HI ALT AIRWAY Range Field. 5) To change the range setting, turn the small FMS Knob to display the range list. 6) Select the desired range using the small FMS Knob. 7) Press the ENT Key. 8) Push the FMS Knob to return to the ‘MAP – NAVIGATION MAP’ Page. Map Declutter Decluttering the MFD map display: Press the DCLTR Softkey with the ‘MAP – NAVIGATION MAP’ Page displayed. The current declutter level is shown. With each softkey press, another level of map information is removed. Decluttering the PFD Inset Map: 1) Press the INSET Softkey. 2) Press the DCLTR Softkey. The current declutter level is shown. With each selection, another level of map information is removed. additional Map display Items Setting up additional ‘Map’ Group items: 1) Press the MENU Key with the ‘MAP – NAVIGATION MAP’ Page displayed. The cursor flashes on the ‘Map Setup’ option. 2) Press the ENT Key. The ‘MAP SETUP’ Window is displayed. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 28 Flight Management Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 3) Turn the small FMS Knob to select the ‘Map’ Group. 4) Press the ENT Key. The cursor flashes on the first field. 5) Turn the large FMS Knob to select the desired option. 6) Turn the small FMS Knob to select ‘On’ or ‘Off’. or: If it is a data field, use the FMS Knob to select the range or time value. 7) Press the ENT Key to accept the selected option and move the cursor to the next item. 8) Repeat Steps 5 through 7, as necessary. 9) Push the FMS Knob to return to the ‘MAP – NAVIGATION MAP’ Page. WayPoINTS aIRPoRTS Selecting an airport for review by identifier, facility name, or location: 1) From the ‘WPT – AIRPORT INFORMATION’ Page (INFo-1 Softkey), push the FMS Knob. 2) Use the FMS Knob and enter an identifier, facility name, or location within the ‘AIRPORT’ Box. 3) Press the ENT Key. 4) Push the FMS Knob to remove the flashing cursor. Selecting a runway: 1) With the ‘WPT – AIRPORT INFORMATION’ Page (INFo-1 Softkey) displayed, push the FMS Knob to activate the cursor. 2) Turn the large FMS Knob to place the cursor in the ‘RUNWAYS’ Box, on the runway designator. 3) Turn the small FMS Knob to display the desired runway (if more than one) for the selected airport. 4) To remove the flashing cursor, push the FMS Knob. Viewing a destination airport: From the ‘WPT – AIRPORT INFORMATION’ Page (INFo-1 Softkey) press the MENU Key. Select ‘View Destination Airport’. The Destination Airport is displayed. Viewing information for a nearest airport on the PFD: 1) Press the NRST Softkey to display the ‘NEAREST AIRPORTS’ Window 2) Highlight the airport identifier with the FMS Knob and press the ENT Key to display the ‘AIRPORT INFORMATION’ Window. Garmin G1000 Cockpit Reference Guide for the Diamond Da42 190-00406-08 Rev. A 29 Flight Management Flight Instruments EIS Nav/Com/ XPDR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS audio and CNS Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 3) To return to the ‘NEAREST AIRPORTS’ Window press the ENT Key (with the cursor on ‘BACK’) or press the CLR Key. The cursor is now on the next airport in the nearest airports list. (Repeatedly pressing the ENT Key moves through the airport list, alternating between the ‘NEAREST AIRPORTS’ Window and the ‘AIRPORT INFORMATION’ Window). 4) Press the CLR Key or the NRST Softkey to close the PFD ‘NEAREST AIRPORTS’ Window. Viewing information for a nearest airport on the MFD: 1) Turn the FMS Knob to select the ‘NRST – NEAREST AIRPORTS’ Page (it is the first page of the group, so it may already be selected). If there are no Nearest Airports available, “NONE WITHIN 200NM” is displayed. 2) Press the aPT Softkey; or push the FMS Knob; or press the MENU Key, highlight ‘Select Airport Window’ and press the ENT Key. The cursor is placed in the ‘NEAREST AIRPORTS’ Box. The first airport in the nearest airports list is highlighted. 3) Turn the FMS Knob to highlight the desired airport. (Pressing the ENT Key also moves to the next airport.) 4) Push the FM