SERVICE INFORMATION LETTER NO. 0183

Enstrom recommends replacing bellcrank P/N 28-16233-1 with P/N 28- 16233-3. Refer to Service Directive Bulletin (SDB) No. 0105. NOTE Reinstall the spring capsule assembly in reverse order (steps a through h in Section 11 of the F-28A/F-28C or 280/280C Series Maintenance Manual (pages MM-11-4 and MM-11-5)). 6.2.15 Check that there is no binding or stiffness in the system, then torque the collective stick socket bolts (Figure 1, Item 2) to full torque (12-15 in-lbs/1.4-1.7 Nm). Verify again that there is no binding or stiffness in the system. 6.2.16 Verify the collective trim rigging IAW Section 11 “Rigging”, page MM-11-6, of the F-28A/F-28C/280/280C Maintenance Manual. UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 5 of 18 6.2.17 Repair the hole in the cabin side wall per AC43.13-1B, Chapter 3. 6.2.18 Proceed to step 6.5. Figure 1. F-28/280 Series Illustrated Parts Catalog, Figure 8-15 Figure 2. F-28/280 Series Illustrated Parts Catalog, Figure 8-11 UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 6 of 18 6.3 F and FX Models – Copilot Collective Stick Socket – Removal 6.3.1 Remove the seats from the aircraft. NOTE Mark all fittings, washers and spacers so they can be properly indexed on reassembly. 6.3.2 Remove the seatbelts (para. 8-7, MM) and remove the seat deck (para. 8-8, MM). 6.3.3 Remove the pilot collective control stick (para. 12-4, MM). CAUTION Set friction on the collective controls to avoid injury if the spring capsule inadvertently releases. 6.3.4 Set friction on the collective controls. 6.3.5 Remove the throttle tie rod assembly (Figure 3). 6.3.6 Remove the copilot throttle bellcrank (Figure 3). Figure 3. Copilot Throttle Bellcrank and Tie Rod UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 7 of 18 6.3.7 Disconnect the throttle cable from the control linkage (Figure 4, and para. 13-12, MM). 6.3.8 Remove the throttle cable jam nut and slide the cable aft (Figure 4). 6.3.9 Remove the bolt securing the cable support assembly and slide aft (Figure 5). Figure 4. Throttle Linkage Figure 5. Support Assembly Removal NOTE For some early production helicopters that have a horizontally installed bolt, check for clearance between the bolt head and the throttle cable. If interference is evident, contact Enstrom Product Support for assistance. UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 8 of 18 CAUTION Failure to secure the spring capsule with special tool, T-0022, may cause serious injury or damage. Ensure the spring capsule is secure when disconnecting the collective bellcrank. WARNING With the capsule in compressed position, there is approximately 180 lbs of force exerted by the springs. Handle with extreme care. 6.3.10 Cage and remove the collective spring capsule (Figure 6 and para. 12-5, MM). Figure 6. Spring Capsule Caged with T-0022 6.3.11 Disconnect one bolt from the collective bellcrank attachment bracket. Take note of the shim and spacer stack when removing the hardware (Figure 7). 6.3.12 Remove the friction hardware and rod assembly (Figure 8). 6.3.13 Remove the four springs from the collective/correlator assembly (Figure 9). 6.3.14 Disconnect the starter wire plug (Figure 9). UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 9 of 18 Figure 7. Copilot Collective Socket/Collective Bellcrank Linkage Figure 8. Friction Control Disassembly UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 10 of 18 Figure 9. Correlator Springs and Starter Wire Plug 6.3.15 Remove the output lever bolt and associated hardware (Figure 10). Note the shim stack up during removal. Figure 10. Correlator Output Lever UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 11 of 18 6.3.16 Remove the two bolts securing the offset collective tube housing to the torque tube (Figure 11). Figure 11. Offset Collective Tube Housing 6.3.17 Index the locking sleeve and the end of the torque tube, then remove one locking sleeve bolt and remove the locking sleeve from the end of the torque tube (Figure 12). 6.3.18 Index the bearing housing, then remove the four bearing housing bolts and remove the bearing housing (Figure 12). Figure 12. Locking Sleeve and Bearing Housing UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 12 of 18 6.3.19 Index the locking sleeve, then remove one locking ring bolt (Figure 13). 6.3.20 Index the collective bellcrank, then remove one collective bellcrank bolt (Figure 13). Figure 13. Locking Sleeve and Collective Bellcrank NOTE Use care when sliding the torque tube to avoid damage to the limit switches or other sensitive components. 6.3.21 Slide the collective torque tube inboard toward the copilot side (Figure 14). Figure 14. Torque Tube Slid Toward the Copilot Seat UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 13 of 18 6.3.22 Remove the collective/correlator assembly from the torque tube (Figure 15). Figure 15. Collective/Correlator Assembly 6.3.23 Remove the four mounting bolts and the four countersunk mounting screws from the mounting plate (Figure 16). Figure 16. Mounting Plate Attachment Disassembly UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 14 of 18 6.3.24 Pivot the bottom of the mounting plate 90 degrees forward and remove (Figure 17). 6.3.25 Remove the locking sleeve from the end of the torque tube (Figure 18). 6.3.26 Remove the copilot-side strap retainer from the torque tube (Figure 18). Figure 17. Mounting Plate Pivot and Removal Figure 18. Locking Sleeve, Strap Retainers, Collective Bellcrank and Collective Stick Socket (bolts removed in a previous step) UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 15 of 18 6.3.27 Remove the bellcrank from the torque tube (Figure 18). 6.3.28 Remove the pilot-side strap retainer from the torque tube (Figure 18). NOTE It may be necessary to remove the chromate primer or rust on the torque tube to facilitate removal of the collective socket. 6.3.29 Remove the two copilot’s collective stick socket bolts and remove the socket (Figure 18). 6.4 F and FX Models – Copilot Collective Stick Socket – Installation NOTE For all bolts connecting the collective stick socket to the torque tube (Figure 1, Item 2), initially torque to shear nut torque (9-11 in-lbs/1-1.2 Nm). Torque to full torque (12-15 in-lbs/1.4-1.7 Nm) after all components are reinstalled and check that there is no binding and that the torque tube moves freely. NOTE Use standard torque unless stated otherwise. Refer to Table 2-5 of the F- 28F/280F Series Maintenance Manual. NOTE Enstrom recommends replacing bellcrank P/N 28-16233-1 with P/N 28- 16233-3. Refer to Service Directive Bulletin (SDB) No. 0105. 6.4.1 Install the new airworthy copilot collective stick socket. Do not overtorque the bolts. Torque the bolts initially to shear nut torque (9-11 in-lbs/1-1.2 Nm). 6.4.2 Reinstall the pilot side strap retainer (Figure 18). 6.4.3 Reinstall the collective bellcrank assembly on the torque tube (Figure 18). 6.4.4 Reinstall the copilot side strap retainer (Figure 18). Do not overtorque the bolts through the strap retainers. Torque to shear nut torque (9-11 in-lbs/1-1.2 Nm). UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 16 of 18 6.4.5 Reinstall the locking sleeve on the torque tube (match the index markings on the torque tube) (Figure 18). Do not overtorque the bolts through the locking ring. Torque to shear nut torque (9-11 in-lbs/1-1.2 Nm). 6.4.6 Slide the torque tube toward the copilot seat. 6.4.7 Reinstall the mounting plate on the torque tube (Figure 17 and Figure 16). 6.4.8 Slide the torque tube into the offset housing. Install the collective/correlator assembly onto the torque tube (Figure 15). 6.4.9 Reinstall the bearing housing on the torque tube (match the index markings on the torque tube) (Figure 12). Do not overtorque the bolts through the torque tube. Torque to shear nut torque (9-11 in-lbs/1-1.2 Nm). 6.4.10 Reinstall the outer locking sleeve on the torque tube (match the index markings on the torque tube) (Figure 12). Do not overtorque the bolts through the torque tube. Torque to shear nut torque (9-11 in-lbs/1-1.2 Nm). 6.4.11 Reinstall the offset collective tube housing to the torque tube (Figure 11). 6.4.12 Reinstall the output lever bolt and associated hardware (Figure 10). 6.4.13 Verify that the torque tube rotates freely before proceeding. 6.4.14 Reinstall the springs and starter wire plug (Figure 9). 6.4.15 Reattach the collective bellcrank to the collective socket arm (Figure 7). 6.4.16 Reinstall the friction assembly (Figure 8). 6.4.17 Reinstall the spring capsule assembly (para. 12-5, D, MM and Figure 6). 6.4.18 Reinstall the support assembly (Figure 5). 6.4.19 Reinstall the copilot collective throttle bellcrank (Figure 3). UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 17 of 18 6.2.20 Check that there is no binding or stiffness in the system, then torque the collective stick socket bolts (Figure 1, Item 2) to full torque (12-15 in-lbs/1.4-1.7 Nm). Verify again that there is no binding or stiffness in the system. 6.4.21 Reinstall the throttle tie rod (Figure 3). 6.4.22 Reinstall the throttle cable (para. 13-12, (2), MM). 6.4.23 Reinstall the pilot collective stick (para. 12-4, 3.B, MM). 6.4.24 Rig the collective trim system (para. 12-5, E, MM). 6.4.25 Rig the correlator (para. 13-12, MM). 6.4.26 Reinstall the seat deck (para. 8-8, B, MM) and the seatbelt (para. 8-7, B, MM). 6.4.27 Reinstall the seats. 6.4.28 Proceed to step 6.5. 6.5 Maintenance Preflight Check, Ground Run, and Test Flight 6.5.1 Preflight Collective Rigging Check 6.5.1.1 Place the collective control stick in full down position and tighten the friction. 6.5.1.2 Check that there is 1/8 to 3/16 inch clearance between the collective bearing housing spacer and the swashplate mount flange (Figure 19). 6.5.1.3 Verify that the correlator rigging has been complied with. 6.5.2 Limited Maintenance Ground Run 6.5.2.1 Verify that the manifold pressure is 16 to 18 inches. 6.5.2.2 Verify that the fuel flow is 50 to 65 lb/hr. UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates. SERVICE INFORMATION LETTER NO. 0183 August19, 2015 Page 18 of 18 6.5.3 Limited Maintenance Flight Check 6.5.3.1 Perform an autorotation and verify that the rotor speed RPM is within limits. Figure 19. Collective Bearing Housing Spacer and Swashplate Mount Flange Clearance 7. PARTS: Refer to the following table to select the new collective stick socket part number. Collective Stick Socket Position Collective Stick Socket P/N Quantity F-28A/280 F-28C/280C F-28F/280F/280FX Pilot Side (LH) 28-16186-3 28-16186-3 N/A 1 Copilot Side (RH) 28-16194-3 28-16194-3 28-16194-3 1 Pilot Side (RH) N/A 28-16377-3 28-16377-3 1 8. SPECIAL TOOLS: Enstrom Tool T-0022 (Collective Spring Capsule Holding Tool) 9. MAN-HOURS: Collective Stick Socket Position Man-Hours F-28A/280 F-28C/280C F-28F/280F/280FX Pilot Side (LH) 2 2 N/A Copilot Side (RH) 8 8 14 Pilot Side (RH) N/A 8 14 10. WARRANTY: N/A 11. WEIGHT CHANGE: N/A 12. LOG BOOK ENTRY: As required for maintenance actions 13. REPETITIVE ACTION: N/A UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED Visit www.enstromhelicopter.com to register for email notification of updates.