SERVICE BULLETIN M20-307B
Mooney M20R Ovation · Checklist
Overview
This service bulletin from Mooney Airplane Company addresses the software upgrade for the GARMIN G1000/GFC700 systems in various Mooney aircraft, including the M20R Ovation. It details the necessary steps for upgrading to software version 006-B0401-30, which enables the installation of the Optional Synthetic Vision System. The bulletin is intended for aircraft owners and maintenance personnel, providing critical instructions for ensuring compliance with the new software requirements. It emphasizes the importance of using compatible SD cards and following specific procedures to avoid issues during the software upload process.
- Software version 006-B0401-30 is required for G1000/GFC700 systems in Mooney aircraft.
- Use SanDisk or Toshiba SD cards for software uploads to avoid issues.
- The pilot's checklist file must be renamed to match the aircraft model for compatibility.
- A post-maintenance check flight is mandatory after software installation.
- This bulletin is applicable to M20M, M20R_Ovation2GX, M20TN, and M20R_Ovation3 models.
Document
Source
Originally published by mooney.com. Sprinkle hosts a reference copy with an added summary, specifications and searchable full text.
Document details
- Type
- Checklist
- Year
- 2008
- Pages
- 10
- File size
- 2.0 MB
- Publisher
- mooney.com
Common. Rarer than 17% of the aircraft models we track.
Most owners only have the POH. Here's the essential set for the Mooney M20R Ovation.
- Pilot's Operating Handbook / AFM
- Checklist
- Maintenance Manual
- Parts Catalog (IPC)
- Systems & Wiring
- Service Bulletins
- Type Certificate (TCDS)
Free — save the MOONEY M20R Ovation to your watchlist and track it in one place.
More Mooney M20R Ovationmanuals & documents
See all 24 →- SERVICE BULLETIN M20-344AEmergency Procedures
- Airworthiness Directive Schedule Aeroplanes Mooney M20 SeriesService Bulletins
- SERVICE BULLETIN M20-341AService Bulletins
- SERVICE INSTRUCTION SIM20-133Weight And Balance
- SERVICE BULLETIN M20-324Service Bulletins
- Comment-Response Document 2015-08Airworthiness Directives
- 2015 Mooney M20R Ovation 3Systems Description
- Garmin G1000 Pilot’s Guide for the Mooney M20M/M20R/M20TNChecklist
- SERVICE BULLETIN M20-318Service Bulletins
- Silent KillerAirworthiness Directives
- Silent KillerAirworthiness Directives
- Type Acceptance Report TAR 96/04 – Mooney M20 SeriesOther Documents
If you fly the Mooney M20R Ovation, you may also be researching these.
In this document
Introduction
The bulletin outlines the need for a software upgrade to the GARMIN G1000/GFC700 systems for Mooney aircraft equipped with earlier software versions. It highlights the requirement for this upgrade to enable the installation of optional features such as the Synthetic Vision System.
Instructions for Software Upgrade
The document provides detailed instructions for extracting and uploading the new software version. It emphasizes the importance of using SanDisk or Toshiba SD cards and ensuring that the aircraft is connected to a ground power unit during the upload process.
Pilot’s Checklist
The bulletin includes instructions for updating the pilot's checklist file on the SD card to ensure compatibility with the new software version. The checklist must be renamed according to the specific Mooney model to be recognized by the G1000 system.
Post Maintenance Check Flight
After the software installation, a post-maintenance check flight is required to verify the proper operation of the aircraft systems, including the Manual Electric Trim system.
Warranty and References
The bulletin states that warranty information is not applicable and provides references to the Garmin G1000 Cockpit Reference Guide and the G1000 System Maintenance Manual for further details.
Safety notes
- Ensure all power connections are secure during software loading to prevent loss of power.
- Loading incorrect software may cause inoperable conditions not covered by warranty.
Full document text
MOONEY AIRPLANE COMPANY, INC. SERVICE BULLETIN 165 Al Mooney Road Kerrville, Texas 78028 MOONEY AIRPLANE COMPANY, INC. 165 Al Mooney Road, Kerrville, Texas 78028 tel: 830-896-6000 www.mooney.com Page 1 of 10 THIS BULLETIN IS FAA APPROVED FOR ENGINEERING DESIGN SERVICE BULLETIN M20-307B Date: November 4, 2008 SUBJECT: GARMIN G1000/GFC700 006-B0401-30 SOFTWARE UPGRADE MODELS/ SN All GARMIN G1000/GFC-700 equipped aircraft with 0401-26 and earlier software. AFFECTED: TIME OF At Owners Discretion COMPLIANCE: INTRODUCTION: Aircraft will require new software load to be completed by a Mooney Authorized Service Center or a GARMIN Authorized Service Center who can access and load the new software revision required to comply with this Service Bulletin. The new software revision will allow the Aircraft to be eligible for the “Optional” Synthetic Vision System to be installed (Unlock Card purchased sep- arately), contact your Mooney Authorized Service Center for details. On software revision 0401-23 and prior, note that the system ID may change as part of the soft- ware upgrade process. Contact Garmin customer support for replacement database or unlock cards if they become inoperative as a result of a system ID change. For prior to 0401-26 software, the pilot’s A/C Checklist (if used) will need to be renamed as a result of the new 0401-30 software upgrade. The new software upgrade will only recognize the checklist file name as to each identified Mooney model (M20M, M20R_Ovation2GX, M20TN, M20R_Ovation3). This checklist gives the pilot basic information as contained the “Normal Pro- cedures” section of the AFM/POH. INSTRUCTIONS: Read entire procedures before beginning work. Identify all optional equipment before installing the software upload. Refer to the Aircraft Flight Manual Section IX - Optional Equipment Supplements (WX500, Fuel Capacity, Transducers, etc.). If the identity is unknown of the trans- ducers installed in the Aircraft, remove top cowl and locate the transducers mounted in the engine compartment on the LH upper engine mount (see Figure SB-307-1). Verify if any optional “Unlock Cards” have been previously installed (JEPP Charts, TAWS, SVS), these will need to be re-installed after the software 0401-30 upgrade. 1.1 - EXTRACT GARMIN 0401-30 SOFTWARE FILE: NOTE: The Service Center performing the work must extract the new software version (006-B0401-30) from the “GARMIN Dealer Website” or Mooney “WebPortal” to a compatible SD Loader Card and compat- ible SD Card Reader (SD Plus memory card reader or compatible) for Software Installation load. NOTE: Garmin recommends the use of SanDisk or Toshiba SD cards to load G1000 software and configura- tion files. If software loading problems occur when using another brand of card, replace the card with a SanDisk or Toshiba card and try the upload procedure again. 1. Download of new GARMIN configuration software (Version 006-B0401-30) will be required. Re- fer to S1.0 Software Download Instructions attached in this procedure. 1.2 VERIFY SYSTEM ID NUMBER (Before and After software upload) 1. Before software upload, note the SYSTEM ID number located on the last page of the Auxiliary page group (see Figure SB-307-2). On software revisions 0401-23 and prior, the customer (or dealer) may need to contact Garmin customer support for replacement database or unlock cards if they become inoperative as a result of a system ID change. MOONEY AIRPLANE COMPANY, INC. 165 Al Mooney Road, Kerrville, Texas 78028 tel: 830-896-6000 www.mooney.com Page 2 of 10 1.3 G1000 SOFTWARE AND CONFIGURATION UPLOAD NOTE: Garmin recommends the use of SanDisk or Toshiba SD cards to load G1000 software and configura- tion files. If software loading problems occur when using another brand of card, replace the card with a SanDisk or Toshiba card and try the upload procedure again. NOTE: Do not remove power from the G1000 during software loading. Do not rely solely on the aircraft bat- teries to prevent loss of power during the software loading process, connect a ground power unit to the aircraft, be sure that BATT 1 is selected. All GDU’s should be in the same mode (configuration or normal), unless instructed differently by the procedure. Remove power only when instructed by the procedure. S Perform these preliminary steps before up-loading software: S Remove supplemental data cards from the lower slot of the GDU’s before loading any software. Supplemental data cards left inserted can become corrupt making them unusable. Replacing corrupt cards is not covered under warranty. NOTE: Loading the wrong software into GIA units may cause an inoperable condition that is not covered by warranty. Identify which type of GIA (WAAS or non-WAAS) LRU is installed in the aircraft, and then choose the correct WAAS or non-WAAS software file before loading GIA software. Loading the incorrect software may necessitate returning the unit to Garmin for a non-warranty repair. The sys- tem may not provide a warning if the incorrect software is selected. 1. Connect a ground power unit to the external power receptacle, and turn on the ground power unit. a.) System Power Up - Apply power to the G1000 by doing the following: (make sure BATT 1 se- lected on Aircraft. Turn on the MASTER switch. Turn on the A/P POWER switch. b.) Note the System ID number as referenced in step 1.2 (see Figure SB M20-307-2) c.) Pull the MFD and PFD circuit breakers. d.) Pull Terrain/Obstacle Database Cards from lower slots in both PFD/MFD (if installed). 2. MFD & PFD Software Load: a.) Insert the 0401-30 Loader Card into the MFD top card slot. b.) While holding the ENT key on the MFD, restore power by closing the MFD circuit breaker. c.) When the words “INITIALIZING SYSTEM” appear in the upper left corner of the MFD, release the ENT key. d.) Press the ENT key to acknowledge the “UPDATE SYSTEM FILES” prompt. NOTE: A softkey labeled ’YES’ appears in the lower right corner and may be used in lieu of the ENT key
Show full textShow less
e.) The “UPDATING SYSTEM FILES. PLEASE WAIT” screen will be displayed. f.) New software is loaded to the MFD. When complete, the MFD starts in configuration mode. g.) When complete, power down the MFD. h.) Remove the 0401-30 Loader Card from the MFD, and re-start in configuration mode. i.) Insert 0401-30 Loader Card into the top card slot on the PFD. Repeat Step 2 for the PFD. j.) When PFD update is complete, it starts in the configuration mode. Do not remove power. - IMPORTANT - For the rest of the software/configuration procedure, do not operate the MFD while loading software or configuration files unless specifically instructed to do so. A failed or cancelled load may result. MOONEY AIRPLANE COMPANY, INC. 165 Al Mooney Road, Kerrville, Texas 78028 tel: 830-896-6000 www.mooney.com Page 3 of 10 1.4 BASE AIRFRAME CONFIGURATION OPTION: 1. Select the System Upload Page on the PFD. 2. Highlight the appropriate airframe in the AIRFRAME field. 3. Press the ENT key. 4. Highlight the appropriate full configuration (WAAS or Non-WAAS) in the FILE field. 5. Press the ENT key. 6. Press the CHK ALL softkey to select all loadable software and configuration files. 7. Press the LOAD softkey. 8. After “Upload Complete” prompt, press the ENT softkey to confirm. 1.5 OPTIONAL SYSTEM CONFIGURATION: NOTE: Ensure that the base airframe configuration option is selected and loaded first after a software upload, LRU replacement, or optional system installation. The optional system configuration (de- tailed below) will be overwritten by the base airframe configuration if the optional system configura- tion is completed first (see Figure SB-307-3) 1. PFD “Optional” Systems Software Load (Options) or (Autopilot): (see Figure SB-307-3) 2. Highlight the appropriate option. 3. Press the ENT key. 4. Highlight the appropriate installation option in the FILE field. 5. Press the ENT key. 6. Press the LOAD softkey. 7. Repeat steps 2 through 6 to load each (applicable) optional items. 8. After “Upload Complete” prompt, press the ENT softkey to confirm. 9. Power system down by turning the MASTER switch to off. 10. Pull 0401-30 Loader Card out of the PFD. 11. Turn on the MASTER switch. Turn on the A/P POWER switch. At this moment, all G1000 equip- ment is receiving power. 12. After software upload, note the SYSTEM ID number located on the last page of the Auxiliary page group (see Figure SB-307-2). On software revisions 0401-23 and prior, the customer (or dealer) may need to contact Garmin customer support for replacement database or unlock cards if the system ID changes as a result of the software upgrade (and the database cards consequently become unusable). 13. Power system down by turning the MASTER switch to off. MOONEY AIRPLANE COMPANY, INC. 165 Al Mooney Road, Kerrville, Texas 78028 tel: 830-896-6000 www.mooney.com Page 4 of 10 1.6 SPLASH SCREEN CONFIGURATION UPLOAD: 1. Insert the 0401-30 loader card into the top card slot of the MFD. 2. Press and hold the ENT key on MFD while applying power. 3. When the words “INITIALIZING SYSTEM” appear in the upper left corner of the MFD, release the ENT key. 4. When the words “Do you want to Update System Files” appear Select NO. 5. When the words “Update Splash Screen” appear Select YES. 6. When complete, one file will be updated (see FIGURES SB-307-4). 7. Power down the MFD and repeat steps 1 thru 6 on the PFD. NOTE: If splash screen is not loaded, the system will prompt a message that the splash screen file not found upon system power-up. 8 Power system down by turning the MASTER switch to off. 9 Pull 0401-30 loader card out of the PFD and store it in a safe place for future system mainte- nance. 1.7 OPTIONAL UNLOCK CARDS (If Previously Installed): 1. Re-Install any previously installed “Unlock Cards” (Jepp Charts, SVS, TAWS). The new software version will not recognize these until you (unlock) each feature. 2 Power system down by turning the MASTER switch to off. 3 Pull Optional Unlock Loader Card out of the PFD and store it in a safe place for future system maintenance. 4. Insert Terrain/Obstacle Database Cards into lower slots in both PFD/MFD. 5. Turn on the MASTER switch. Turn on the A/P POWER switch. At this moment, all G1000 equip- ment is receiving power. 6. Verify that all software systems (Options, Autopilot, Unlock Cards etc.) for your aircraft have been installed. 1.8 POST INSTALLATION GROUND CHECK: 1. Perform post-installation ground checks per Section 8 (only Steps 8.1 thru 8.5) of G1000 System Maintenance Manual P/N 190-00907-00 Revision B or Later Revision. 1.9 POST MAINTENANCE CHECK FLIGHT: 1. Return aircraft to service. 2. Perform a Post Maintenance Check Flight per GFC700 Flight Manual Supplement to check prop- er operation of the Manual Electric Trim system (refer to the M20M, M20R, M20TN aircraft POH/ AFM Supplement “GARMIN GFC 700 AUTOMATIC FLIGHT CONTROL SYSTEM AND TAWS OPTION”). 3. Complete log book entry for procedure. MOONEY AIRPLANE COMPANY, INC. 165 Al Mooney Road, Kerrville, Texas 78028 tel: 830-896-6000 www.mooney.com Page 5 of 10 1.10 PILOT’S CHECKLIST: (SD CARD) if prior to 0401-26 software installation: 1. Plug your SD card reader into a laptop or PC. 2. Insert the A/C Pilot’s Checklist “SD Card” (Mooney supplied) into the SD card reader. 3. The current checklist file on the SD card should have the filename as “chklist.ace” NOTE: Some Operating Systems will allow the user to view file names only and not file extensions. Make sure you rename the file based on the these settings. 4. Highlight file and rename according to the Models listed below: (see FIGURES SB-307-5 & 6) a.) M20M (or M20M.ace) b.) M20R_Ovation2GX (or M20R_Ovation2GX.ace) c.) M20R_Ovation3 (or M20R_Ovation3.ace) d.) M20TN (or M20TN.ace) 5. Insert your Pilot’s Checklist SD Card into top slot of MFD and power-up to verify the G1000 reads the renamed checklist. 6. Procedure complete. WARRANTY: N/A REFERENCE 1. Garmin G1000 Cockpit Reference Guide 190-00450-04 Revision A or Later FAA approved DATA: revision (Can be Downloaded from Garmin Dealer Resource or Mooney WebPortal). 2. Garmin G1000 System Maintenance Manual P/N 190-00907-00 Revision B or Later approved revision. 3. MAC AFM/POH Manual (applicable A/C) PARTS LIST: Mooney Airplane Company, Inc., Parts Kit: Item P/N Description Qty Software 006-B0401-30 GARMIN Software Revision (Rev 30) 1 (Download file) https://www8.garmin.com/dealerResource (Download file) http://manuals.mooney.com/ MOONEY AIRPLANE COMPANY, INC. 165 Al Mooney Road, Kerrville, Texas 78028 tel: 830-896-6000 www.mooney.com Page 6 of 10 KULITE TRANSDUCER KAVLICO TRANSDUCER KULITE TRANSDUCERS SHOWN Figure SB M20-307-1 - TRANSDUCER IDENTIFICATION BEFORE SOFTWARE UPLOAD Note the System ID Number Before and After Software Upload. Last Page of the Auxiliary page group FIGURE SB-307-2 - LOCATING THE SYSTEM ID NUMBER OPTIONS - SELECTION AUTOPILOT - SELECTION FIGURE SB-307-3 - VERIFY OPTIONS OR AUTOPILOT LIST MOONEY AIRPLANE COMPANY, INC. 165 Al Mooney Road, Kerrville, Texas 78028 tel: 830-896-6000 www.mooney.com Page 7 of 10 Old Style Splash Screen New Style Splash Screen FIGURE SB-307-4 - VERIFY THE SOFTWARE VERSION ON SPLASH SCREEN Rename file: M20TN Figure SB M20-307-5 - WINDOWS VIEW WITH FILENAME ONLY Rename file: M20TN.ace Figure SB M20-307-6 - WINDOWS VIEW WITH FILENAME AND EXTENSION MOONEY AIRPLANE COMPANY, INC. 165 Al Mooney Road, Kerrville, Texas 78028 tel: 830-896-6000 www.mooney.com Page 8 of 10 S1.0 Extracting the revised GARMIN Software (from Website): 1. Log in to the Garmin Dealer Website or Mooney WebPortal (both must have user name and password) web address is: https://www8.garmin.com/dealerResource or http://manuals.mooney.com/ 2. Read the Confidentiality Agreement page and select on the “I AGREE” button. 3. The screen will contain the Technical Resources options. Select on the Field Loadable Software link. This link will open the manufacturer front page, select on Mooney Aircraft Link. 4. Insert your SD Loader Card into the Card Reader. 5. Select on the link Software Revision (006-B0401-30_0A). A pop-up screen will prompt you to “Run” or “Save” the file. Select “Run” to acknowledge the following (example) prompt: Example Screen Shot xx MOONEY AIRPLANE COMPANY, INC. 165 Al Mooney Road, Kerrville, Texas 78028 tel: 830-896-6000 www.mooney.com Page 9 of 10 6. Some servers have Security Warnings (contact your System Administrator if an error occurs), Select “Run” to ac- knowledge the following (example) prompt: 7. To extract the required files, select “SetUp” to acknowledge the following (example) prompt: xx 8. Verify the Drive letter where the SD Card reader is plugged in, select “Next” to acknowledge the following (example) prompt: 9. Files will now extract to SD Card, monitor the download process: MOONEY AIRPLANE COMPANY, INC. 165 Al Mooney Road, Kerrville, Texas 78028 tel: 830-896-6000 www.mooney.com Page 10 of 10 10. When the download is complete, select “Finish” to acknowledge the following prompt: 11. When complete the SD Loader Card can now be ready for Software Installation to the Aircraft G1000 PFD/MFD.