SERVICE BULLETIN NO. 540B

PIPER Aztec PA-23-250 · Service Bulletins

Free account — keep the POHs & checklists you reference in one place.

Overview

This document is Service Bulletin No. 540B issued by Piper Aircraft, Inc., which mandates inspections and potential repairs of the stabilator tip tube and weight assembly for the Piper Aztec PA-23-250 aircraft. It supersedes the previous bulletin (SB 540A) and expands the serial number effectivity, emphasizing the importance of recurring inspections to ensure safety.

Compliance with SB 540B is mandatory.
Initial inspection should coincide with the next scheduled maintenance, not exceeding 10 hours of service.
Recurring inspections are required every 100 hours of service.
Cracks in the stabilator tip tube and weight assembly must be repaired before the next flight.
The bulletin applies to specific serial numbers of the PA-23-250 Aztec.
Engineering aspects of the bulletin are FAA approved.
Repairs must follow specific instructions outlined in the bulletin.
Documentation of compliance is required in the aircraft logbook.

Document

Source

Originally published by regulations.gov. Sprinkle hosts a reference copy with an added summary, specifications and searchable full text.

View original at regulations.gov

Report a problem or request removal

Document details

Type: Service Bulletins
Year: 2021
File size: 310 KB
Publisher: regulations.gov
Language: en

About this document

What is the SERVICE BULLETIN NO. 540B?

The SERVICE BULLETIN NO. 540B is a service bulletins for the PIPER Aztec PA-23-250, dated 2021.

Where does the SERVICE BULLETIN NO. 540B come from?

This copy of the SERVICE BULLETIN NO. 540B was originally published by regulations.gov and is hosted on Sprinkle as a free, searchable reference copy.

What year was the SERVICE BULLETIN NO. 540B published?

The SERVICE BULLETIN NO. 540B — the PIPER Aztec PA-23-250 service bulletins on file — is dated 2021.

Documentation completeness

5/7

Most owners only have the POH. Here's the essential set for the PIPER Aztec PA-23-250.

More PIPER Aztec PA-23-250manuals & documents

In this document

Purpose

The bulletin aims to prevent the separation of weight assemblies from stabilator tip tubes due to cracks, which could lead to unsafe flying conditions.

Compliance Time

Initial inspections must be completed during the next scheduled maintenance, not exceeding 10 hours of service, with recurring inspections every 100 hours.

Inspection Instructions

Detailed steps for inspecting the stabilator tip tube and weight assembly for cracks, including the use of specific tools and methods.

Repair Instructions

Instructions for repairing the stabilator tip tube and weight assembly, including necessary modifications and welding precautions.

Material Required

Lists materials needed for repairs, noting that some parts may not be available from Piper.

Documentation of Compliance

Instructions for making a logbook entry to document compliance with the service bulletin.

Safety notes

Any cracks discovered in the aircraft structure must be repaired prior to the next flight.
An airplane with cracks does not meet its type design and lacks required strength.
Use TIG or MIG welding to repair cracks near the lead weight; do not use oxy-acetylene.

Full document text

Date: February 9, 2021 (M) SERVICE BULLETIN NO. 540B PIPER CONSIDERS COMPLIANCE MANDATORY Piper Aircraft, Inc. 2926 Piper Drive Vero Beach, FL, U.S.A. 32960 (OVER) ATA/JASC: 5510 Service Bulletin (SB) 540B supersedes SB 540A in its entirety. Aircraft that were previously made compliant with SB 540A must continue the recurring inspections mandated by SB 540B, regardless of prior maintenance and repair history. SUBJECT: INSPECTION AND REINFORCEMENT OF STABILATOR TIP TUBE AND WEIGHT ASSEMBLY REASON FOR REVISION: SB 540B expands serial number effectivity and mandates a recurring inspection of all affected aircraft. Other changes are to bring the document up to current format. MODELS AFFECTED: SERIAL NUMBERS AFFECTED: PA-23-250 (Six-Place) Aztec “F” 27-7654001 through 27-7954121 COMPLIANCE TIME: If not already accomplished, the initial inspection is to coincide with the next regularly scheduled maintenance event, but not to exceed the next ten (10) hours time in service. Thereafter, inspection is on a recurring basis at a frequency interval not to exceed 100 hours time in service. APPROVAL: The engineering aspects of this service document have been shown to comply with the applicable Federal Aviation Regulations and are FAA approved. PURPOSE: Field reports indicate that cracks have been found in the stabilator tip tube and weight assembly installed on the affected aircraft, regardless of prior maintenance and repair history. If not identified and addressed, this condition could result in separation of the weight from the tube. This service bulletin provides instructions to inspect the stabilator tip tube and weight assembly for cracks, and provides options to address any cracks discovered. SAFETY INTENT: The safety intent of this service bulletin is to require inspections to prevent the separation of weight assemblies from the stabilator tip tubes, which could result in an unsafe flying condition. CONFIGURATION DESCRIPTION: Incorporating this service bulletin will ensure that if cracks should develop in stabilator tip tubes and weight assemblies, the cracks are repaired appropriately. SERVICE BULLETIN NO. 540B PAGE 2 of 6 INSTRUCTIONS: NOTE: Some steps in these instructions are identified as “required for compliance” (RC). If this service bulletin is mandated by an airworthiness directive (AD), the steps identified as RC must be done to comply with the AD. Steps not identified as RC are recommended and may be deviated from, done as a part of other actions, or done with accepted methods different from those given in this service bulletin, if the RC steps can be done and the airplane can be put back in a serviceable condition. WARNING: ANY CRACKS DISCOVERED IN THE AIRCRAFT STRUCTURE MUST BE REPAIRED PRIOR TO THE NEXT FLIGHT. AN AIRPLANE WITH CRACKS IN ITS STRUCTURE DOES NOT MEET ITS TYPE DESIGN AND NO LONGER POSSESSES ITS REQUIRED TYPE DESIGN STRENGTH. NOTE: The temporary removal of some components and/or access panels may be required in order to accomplish the instructions in this service bulletin. NOTE: These instructions apply to both the left and right stabilator tip tube and weight assemblies. NOTE: The kits and service replacements for some components mentioned in this service bulletin are not currently available. If repair or replacement is necessary, some other FAA approved replacement or repair may be required. Contact Piper Customer Service for assistance at (+1) 772-299-2141 or CustomerService@piper.com. Piper’s normal business hours are Monday through Friday, 7:30 a.m. to 4:30 p.m. (Eastern). Part I. Inspection NOTE: The repair or replacement of the tip tube and weight assembly does not alleviate the recurring inspection mandated by this service bulletin. 1. RC – Prior to inspection, wipe surfaces clean using a soft cloth dampened with isopropyl alcohol, mineral spirits, naphtha, or another suitable cleaning agent or method. 2. RC – If Stabilator Balance Weight Replacement Kit, Piper P/N 763-987, is installed, and Stabilator Nose Rib Installation Kit, P/N 761-141, is not, then modification of the nose rib may be required. Refer to Piper Service Letter 807, latest revision, to identify the affected aircraft. 3. RC – For serial numbers (S/Ns) 27-7654001 through 27-7954035 if Stabilator Balance Weight Replacement Kit, Piper P/N 763-987, is not installed: examine the inspection areas identified in Figure 1. Perform the inspection using a 10X magnifier, a mirror, and a suitable light source or other equipment capable of providing equal or better resolution. • If cracks are found, repair the tube and weight assembly as described in Part II, prior to next flight. • If no cracks are found, then proceed to Part III. NOTE: Figure 1 shows a stabilator tip tube and weight assembly after repair. NOTE: At the discretion of the owner/operator, the repair described in Part II may be accomplished on a stabilator tip tube and weight assembly without cracks. However, the recurring inspection mandated by this service bulletin shall still apply. If the repair described in Part II has already been accomplished, and repair is necessary, then some other FAA approved repair is required. Contact Piper Customer Service for assistance at (+1) 772- 299-2141 or CustomerService@piper.com. Piper’s normal business hours are Monday through Friday, 7:30 a.m. to 4:30 p.m. (Eastern). 4. RC – For S/Ns 27-7954036 through 27-7954121; and for S/Ns 27-7654001 through 27-7954035 if Stabilator Balance Weight Replacement Kit, P/N 763-987, is installed: examine the inspection areas identified in Figure 2. Perform the inspection using a 10X magnifier, a mirror, and a suitable light source or other equipment capable of providing equal or better resolution. • If cracks are found, then repair is necessary prior to next flight. Contact Piper Customer Service for assistance at (+1) 772-299-2141 or CustomerService@piper.com. Piper’s normal business hours are Mon-

Show full text

day through Friday, 7:30 a.m. to 4:30 p.m. (Eastern). • If no cracks are found, then proceed to Part III. SERVICE BULLETIN NO. 540B PAGE 3 of 6 Figure 1 Top View and Side View of Tube and Weight Assembly 0.25 HOLE THROUGH SQUARE TUBE ONLY. ROSETTE WELD AT TOP AND BOTTOM. (5 PLACES) 0.25 HOLE THROUGH SQUARE TUBE ONLY. ROSETTE WELD AT BOTH SIDES. TUBE ATTACHMENT PLATE LEAD WEIGHT 0.191 HOLE THROUGH SQUARE TUBE AND ROUND TUBE ROUND TUBE SQUARE TUBE SIDE VIEW APPLICABLE TO S/N 27-7654001 THROUGH 27-7954035 WITHOUT PIPER KIT P/N 763-987 END CUT WELD DETAIL INSPECTION AREAS FWD FWD TOP VIEW 1.50 2.75 5.00 7.25 9.50 10.00 NOTE: All measurements are in inches unless otherwise identified. SERVICE BULLETIN NO. 540B PAGE 4 of 6 Figure 2 Side View of Tube and Weight Assembly INSPECTION AREAS SIDE VIEW APPLICABLE TO S/N 27-7654001 THROUGH 27-7954035 WITH PIPER KIT P/N 763-987 INSTALLED, AND S/N 27-7954036 THROUGH 27-7954121 FWD TUBE ATTACHMENT PLATE LEAD WEIGHT SERVICE BULLETIN NO. 540B PAGE 5 of 6 Part II. Repair Instructions RC – These repair instructions are applicable only to S/Ns 27-7654001 through 27-7954035 without Kit P/N 763-987 installed. Refer to Figure 1. NOTE: All measurements are in inches, unless otherwise identified. NOTE: The repair or replacement of the tip tube and weight assembly does not alleviate the recurring inspection (Part I) mandated by this service bulletin. 1. RC – Remove the stabilator tip tube and weight assembly from the aircraft. 2. RC – Modify both tube and weight assemblies as follows: a. Remove the tube and weight assemblies from both stabilators. Retain screws, washers and nuts for reinstallation; replace any hardware on condition. b. Cut or drill a hole in the end of the tube attachment plate to allow a 5/8 inch diameter tube to be inserted into the square tube. c. Locate and drill twelve (12) 0.250 holes in the square tube as shown in Figure 1. d. Insert a 10-inch length of round steel tube (5/8 x 0.058 Type 4130 Cond. N) into the square tube and rosette weld the tubes together at the twelve (12) 0.250 holes. e. Weld shut the area around the hole in the attachment plate and the tubes. f. Weld shut any cracks that were discovered when inspecting the square tube. CAUTION: IF WELDING CRACKS NEAR THE LEAD WEIGHT, USE TIG OR MIG WELD TO REPAIR. DO NOT USE OXY-ACETYLENE. g. Drill a 0.191 hole through the round tube using existing hole in square tube as a guide. h. Clean, prime and paint tube and weight assembly. i. Reinstall the tube and weight assembly to the stabilator using existing attachment hardware. j. Reinstall the tip assembly to the stabilator. k. Refer to Piper Aztec Service Manual, P/N 753-564, paragraph 4-65, to balance the stabilator. NOTE: If the stabilator cannot be properly balanced with the trim weights at the stabilator balance arm, it is permissible to remove up to 1/4 inch of material from the forward ends of the lead weights on the stabilator tips. (Remove equal amounts from both lead weights.) 3. Proceed to Part III. Part III. Documentation of Compliance Make a logbook entry documenting compliance with this service bulletin. SERVICE BULLETIN NO. 540B PAGE 6 of 6 MATERIAL REQUIRED: Per aircraft, on condition: Per Part II: two (2) each, Round Steel Tube, 10 x 5/8 x 0.058 inch Type 4130 Cond. N. (The tube, P/N 15589-05, is unavailable from Piper Aircraft, Inc.) AVAILABILITY OF PARTS: Procure locally or from your Piper Approved Service Center EFFECTIVITY DATE: This service bulletin is effective upon receipt. SUMMARY: Please contact your Piper Approved Service Center to make arrangements for compliance with this service bulletin in accordance with the compliance time indicated. NOTE: Please notify the factory of any address/ownership corrections. Changes should include aircraft model, serial number, and current owner’s name and address. Corrections and/or changes should be directed to: PIPER AIRCRAFT, INC. Att’n: Customer Service 2926 Piper Drive Vero Beach, FL 32960 or: CustomerService@piper.com Please include in subject line: “Aircraft ownership update” 1 Aircraft Certification Service Compliance & Airworthiness Division Atlanta ACO Branch 1701 Columbia Ave. College Park, Georgia 30337 April 23, 2021 In Reply, Reference FAA Correspondence #: 7A0-21-5958 Mr. Mitch Cannon ODA Administrator Piper Aircraft 2626 Piper Drive Vero Beach, FL 32960 Ref: Piper Service Bulletin 540, revision B, dated February 9, 2021 Subject: Alternative Method of Compliance (AMOC) for Airworthiness Directive (AD) 78-02-03, Paragraph (a) which requires inspections and modifications to the stabilator tip tube and weight assemblies per Piper Service Bulletin 540, dated January 4, 1977 Dear Mr. Cannon, The Federal Aviation Administration (FAA) has received your proposal dated April 15, 2021, proposing an alternative method of compliance (AMOC) to paragraph (a) of Airworthiness Directive 78-02-03. The Atlanta Aircraft Certification Office approves your AMOC proposal regarding paragraph (a) of AD 78-02-03. Your proposal to accomplish the inspections and modifications as specified in Piper Service Bulletin 540, revision B as an alternate means of compliance (AMOC) to paragraph (a) of AD 78-02-03 is acceptable for the serial numbers applicable to Piper Service Bulletin 540, revision B. The following documentation provides the substantiating data used to establish the acceptable level of safety which was the basis for approving the AMOC. 1. Piper Letter dated April 15, 2021 indicating that Piper Service Bulletin 540, revision B meets the requirements of AD 78-02-03 paragraph (a) for PA23-250 aircraft with applicable serial numbers. 2. Piper Service Bulletin 540, revision B, dated February 9, 2021. This FAA AMOC is transferable with the aircraft to an operator who operates the aircraft under U.S. registry. 2 Before using this AMOC notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local Flight Standards District Office/Certificate Holding District Office. The preceding paragraph also applies to any applicable foreign-registered aircraft upon transfer of the aircraft to the U.S. registry if compliance with the AMOC has not been accomplished This AMOC only applies to the FAA AD listed above. The FAA does not have the authority to approve this as an AMOC to any AD issued by another civil aviation authority (CAA). Approval of an AMOC to another CAA’s AD must come from that CAA. A copy of this response will be forwarded to the CAA where these aircraft may be registered for their consideration All provisions of AD 78-02-03 that are not specifically referenced above remain fully applicable and must be complied with accordingly. The Atlanta Aircraft Certification Office (ACO) will revoke this AMOC if the Atlanta ACO later determines that this AMOC does not provide an acceptable level of safety. If you have any questions or need additional information, please contact John R. Marshall, PE at telephone 404-474-5524, fax 404-474-5566, or electronic mail at john.r.marshall@faa.gov. Sincerely, (for) Christina M. Underwood Manager, Atlanta ACO Branch

All PIPER Aztec PA-23-250 service bulletins