Service Bulletin Number : SB-AG-39

aircraft to service Rework: z 1.Gain access to the main spar splice fittings. Remove the spray pump and spray pump mounting brackets. z 2.Remove the 1/4, 5/16 and 1/2 inch bolts (first, second and fourth from the ends of the splice fittings). z 3.Thoroughly clean in and around the splice fittings and bolt holes. z 4.Remove the paint from the spot faces of the 1/2 inch holes in the splice fitting. z 5.With 250 grit or finer sand paper, clean the 1/2 inch bolt holes so that they easily accept the 1/2 bolts of the ESK 556-1 fixture assembly. z 6.Install the ESK 556-1 fixture. z 7.Lubricate the 0.2490 reamer and with the reamer bushing installed in the fixture, ream the 1/4 inch holes. z 8.Lubricate the 0.3110 reamer and with the reamer bushing installed in the fixture, ream the 5/16 inch holes. z 9.Remove the ESK 556-1 fixture. z 10.Using the attached Fatigue Technology, Inc. procedure described in F.T.I. Document No. 52373, cold expand the 1/4 and 5/16 inch holes. z 11.Install the ESK 556-1 fixture. z 12.Lubricate the 0.2646 reamer (smaller of the two 1/4 inch final reamers) and with the reamer bushing installed in the fixture, ream the 1/4 inch holes. z 13.Lubricate the 0.3268 reamer (smaller of the two 5/16 inch final reamers) and with the reamer bushing installed in the fixture, ream the 5/16 inch holes. *WARNING* If cracks or flaws are found, either replace the spar cap or wing prior to the next flight or reassemble the splice fittings and proceed with the rework if there is a possibility that oversizing the holes will remove the crack or flaw. Contact Ayres Corporation if a ferry flight to a suitable repair station is required. *WARNING* Under no circumstances attempt to ream a hole without the use of the ESK 556-1 fixture and bushings. *NOTE* The oversize repair bolts are manufactured to a tolerance of 0.2641 - 0.2651 for the "x" oversize 1/4 inch bolt and 0.3266 - 0.3276 for the "x" oversize 5/16 z 14.Insert an "x" oversize 1/4 inch bolt into one of the 1/4 inch holes. If resistance is encountered, encourage the installation with moderate taps of a 6 ounce plastic mallet. If further resistance is encountered or it appears that installation will remove the cadmium plate from the bolt, remove the bolt and ream the hole with the 0.2651 final reamer (larger of the two final reamers). z 15.In a similar manner, prepare the other 1/4 inch hole. z 16.Using similar technique and precautions, prepare the 5/16 inch holes for "x" oversize 5/16 inch bolts using the 0.3110 and 0.3276 inch reamers. z 17.Mark these 1/4 and 5/16 inch "x" oversize bolts and be sure to install them in their respective holes during reassembly. z 18.Remove the remaining spar splice bolts and the spar splice fittings per the attached removal procedure. z 19.Remove all corrosion from all of the bolt holes by mechanical and/or chemical means. z 20.Thoroughly clean the area in and around the 1/4 and 5/16 bolt holes and remove the paint from an area extending one inch from the center of each of these holes. z 21.If rust or corrosion is found anywhere on the spar cap or spar web, perform SB-AG-29 in conjunction with this bulletin. z 22.Inspect the walls of the 1/4 and 5/16 inch bolt holes in the lower spar cap for cracks or flaws using magnetic particle or equivalent flaw detection equipment. z 23.If no cracks or flaws are found, prime and repaint areas where the paint was removed. z 24.Drill or ream the MS20002C4 washers to 0.2720. Drill or ream the MS20002C5 to 0.332. z 25.Reassemble the splice fittings per the attached installation procedure. Use all new nuts, bolts and washers. z 26.Install the pump mount and brackets. z 27.Return the aircraft to its airworthy configuration, make appropriate log book entries and return the aircraft to service. inch bolt. The diameter of a reamed hole depends on reamer quality, operator technique, lubricant, RPM and other factors. Because of these variations in bolt diameter and hole size, bolt-in-hole fit will vary. Use caution when installing the bolts so as not to remove the bolt cadmium plating on installation. *NOTE* If the bolt is still excessively tight after using the larger final reamer, use a micrometer to check the mandrel for wear, the reamer for wear, and the bolt diameter, it may be required to select a bolt with a small diameter. *WARNING* If cracks or flaws are found, replace the spar cap or wing prior to the next flight. Contact Ayres Corporation if a ferry flight to a suitable repair station is required. WEIGHT AND BALANCE:No change. PUBLICATIONS AFFECTED:None. RECORD OF COMPLIANCE:Make appropriate airframe logbook entry. Complete the SB-AG-39 compliance card and mail to Ayres Corporation. LOWER SPLICE FITTING REMOVAL(Reference Figure 1) z 1.Park the aircraft in a closed door hangar and secure the aircraft for maintenance. z 2.Disconnect the battery and external power sources. z 3.Gain access to the wing splice area by removing the wing root fairings and the necessary aircraft side and belly panels. z 4.Support the wings at the jack points located approximately 6 feet from the wing tips and under various wing ribs to prevent wing movement when the attach bolts are removed. z 5.Back the locknuts off of the NAS bolts in the splice fittings far enough to conceal the end of the bolt threads. Spray the bolt shanks with WD-40 or an equivalent lubricant. z 6.Remove the AN5 bolts securing the tubes to the tube nuts and loosen the lower splice fitting tube nuts. As the nuts are loosened, the bolts will back out of the holes. Once the tube nuts are off of the lower bolts, loosen the upper tube nuts to back them out of the holes. If one of the bolts does not move, rethread the tube nut onto this bolt and place a spacer between the opposite end of the tube and the spar cap (or NAS bolt). Proceed, once again, to loosen the tube nut and back the bolt out of the hole. Remove the tubes and tube nuts once sufficient clearance has been obtained. z 7.Place an aluminum block on the smallest nut and with a 4X rivet gun, drive the nut flush to the splice fitting. Proceed in a similar manner with the remainder of the bolts working from the smallest to the largest. z 8.Remove all of the nuts and tube nuts from the NAS bolts. Place the aluminum block on the threaded end of the smallest bolt and with the 4X rivet gun, drive it flush with the splice fitting. Proceed in a similar manner with the remainder of the bolts working from the smallest to the largest. z 9.Pry the lower splice fitting (top half) off of the NAS bolts by tapping aluminum wedges between the lower splice fitting (top half) and the lower spar cap. Remove the top half of the lower splice fitting. z 10.Place the aluminum block on the threaded end of the smallest bolt in the lower splice fitting and with a 2X rivet gun, drive it flush with the spar cap. Proceed in a similar manner with the remainder of the bolts working from the smallest to the largest. *CAUTION* Extreme care must be taken to avoid damaging the spar cap and the surface finish of the holes through the spar cap. *NOTE* Adjusting the angle of the wings with the wing jacks may assist in wing bolt removal. z 11.Pry the lower splice fitting (bottom half) off of the lower spar cap by tapping aluminum wedges between the two. Remove the bottom half of the lower splice fitting along with the NAS bolts. z 12.Discard all used nuts, bolts and washers. z 13.Clean and remove corrosion from the splice fittings. LOWER SPLICE FITTING INSTALLATION (Reference Figure 1) z 1.Install the upper tube nuts and torque to specification in accordance with the Figure 2 torque chart. z 2.Grease the the 12 NAS wing splice attach bolts and the holes in the lower splice fittings (top and bottom halves) with Moly-Disulfide grease. Insert the two large NAS bolts with MS20002C countersunk washers installed into the lower splice fitting (bottom half). Be sure to mate the countersunk portion of the washer with the head of the bolt. Insert the remaining 10 NAS bolts with their respective, properly orientated, MS20002C washers into their respective holes and position all 12 bolts flush with the top face of the lower fitting (bottom half). z 3.Apply Moly-Disulfide grease to the matching holes in the lower spar cap and place the top splice fitting into position. Press the bolts through the holes in the lower spar cap. z 4.Place the lower splice fitting (top-half) into position and press the fitting downward over the bolts. Install MS20002 (no countersink) washers (12 places). Slip the 20240-1 tubes over the upper splice tube nuts and install the lower splice tube nuts. Bring the 20239-4 tube nuts (2 places) and the AN365 nuts (10 places) up snug. z 5.Torque the tube nuts and the AN365 locknuts on the NAS bolts through the lower splice fittings per Figure 2, 4 places and 20 places, respectively. z 6.Position the tubes equidistant between the upper and lower tube nuts. Drill 5/16 inch diameter holes (+0.003, -0.001), 2 places per tube, parallel to the spar web through the pilot holes in the tubes and through the tube nut shanks, 4 places total. Install AN5 bolts through these holes and secure with AN960 washers and AN365 locknuts. Torque locknuts per Figure 2. z 7.Remove the wing jacks. View Figure 1(350k) *WARNING* Under no circumstances should the bolts be turned while the threads are in the spar cap. This could damage the hole surface finish which could result in a stress concentration. *CAUTION* Use extreme care to avoid damaging the spar cap or the surface finish of the holes through the spar cap. Figure 2 Bolts Steel Tension Bolts Steel Tension Bolts Aluminum AN 3 thru AN20 MS 20004 thru MS 20024 AN 3DD thru AN 20DD AN 42 thru AN49 NAS 114 thru NAS 158 AN 173DD thru AN 186DD AN 73 thru AN81 NAS 333 thru NAS 340 AN 509DD AN 173 thru AN186 NAS 583 thru NAS 590 AN 525D MS 20033 thru MS20046 NAS 624 thru NAS 644 MS 27039D MS 20073 NAS 1303 thru NAS 1320 MS 24694DD MS 20074 NAS 172 AN 509 NK9 NAS 174 MS 24694 NAS 517 AN 525 NK 525 Steel shear bolt MS27039 NAS 464 Nuts Nuts Nuts Steel Tension Steel Shear Steel Tension Steel Shear Aluminum Tension Aluminum Shear AN 310 AN 320 AN 310 AN 320 AN 365D AN 320D AN 315 AN 364 AN 315 AN 364 AN 310D AN 364D AN 363 NAS 1022 AN 363 NAS 1022 NAS 1021D NAS 1022D AN 365 MS 17826 AN 365 MS 17826 NAS 1021 MS 20364 MS 17825 MS 20364 MS 17825 MS 20365 MS 21045 MS 21045 MS 20365 NAS 1021 MS 20500 NAS 679 NAS 679 NAS 1291 FINE THREAD SERIES Nut- Bolt Size Torque Limits In. - lbs. Torque Limits In. - lbs. Torque Limits In. - lbs. Torque Limits In. - lbs. Torque Limits In. - lbs. Torque Limits In. - lbs. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. 8 -36 12 15 7 9 5 10 3 6 8 -36 20 25 12 15 25 30 15 20 10 15 5 10 1/4 - 28 50 70 30 40 80 100 50 60 30 45 15 30 5/16 - 24 100 140 60 85 120 145 70 90 40 65 25 40 3/8 - 24 160 190 95 110 200 250 120 150 75 110 45 70 7/16 - 20 450 500 270 300 520 630 300 400 180 280 110 170 1/2 - 20 480 690 290 410 770 950 450 550 280 410 160 260 9/16 - 18 800 1,000 480 600 1,100 1,300 650 800 380 580 230 360 5/8 - 18 1,100 1,300 660 780 1,250 1,550 750 950 550 670 270 420 3/4 - 16 2,300 2,500 1,300 1,500 2,650 3,200 1,600 1,900 950 1,250 560 880 7/8 - 14 2,500 3,000 1,500 1,800 3,550 4,350 2,100 2,600 1,250 1,900 750 1,200 1 -14 3,700 4,500 2,000 3,300 4,500 5,500 2,700 3,300 1,600 2,400 950 1,500 1 1/8 -12 5,000 7,000 3,000 4,200 6,000 7,300 3,600 4,400 2,100 3,200 1,250 2,000 1 1/4 -12 9,000 11,000 5,400 6,600 11,000 13,400 6,600 8,000 3,900 5,600 2,300 3,650 COARSE THREAD SERIES 8 -32 12 15 7 9 10 - 24 20 25 12 15 1/4 - 20 40 50 25 30 5/16 - 18 80 90 48 55 3/8 - 16 160 185 95 110 7/16 - 14 235 255 140 155 1/2 - 13 400 480 240 290 9/16 - 12 500 700 300 420 5/8 - 11 700 900 420 540 3/4 - 10 1,150 1,600 700 950 7/8 -9 2,200 3,000 1,300 1,800 1 -8 3,700 5,000 2,200 3,000 1 1/8 -8 5,500 6,500 3,300 4,000 1 1/4 -8 6,500 8,000 4,000 5,000 service bulletin Service Bulletin Number : SB-AG-39 Rev. 1 December 12, 1997 SB-AG-39 Revised Compliance Options and Inspection Intervals Models Affected: Group 1 Airplanes Perform initial inspection at 2000 hours time in service (TIS). Group 2 Airplanes Model Serial Numbers S2R 5000 through 5099R S2R-R1340 R1340-011,R1340-012,R1340-019,R1340-020, R1340-024, R1340-025, and R1340-027 S2R-R1820 R1820-001 through 1820-035 S2R-T34 6000R through 6049R, T34-001 through T34-143, T34-145, T34-147 through T34-167, T34-171, T34-180, and T34-181* S2R-T15 T15-001 through T15-033** S2R-T11 T11-001 through T11-005 S2R-G1 G1-101 through G1-108 * The serial numbers of the Model S2R-T34 airplanes could incorporate T34-xxx, T36-xxx, or T41-xxx or T42-xxx. This Service Bulletin applies to all of these serial number designations, as they are Model S2R-T34 airplanes. ** The serial numbers of the Model S2R-T15 airplanes could incorporate T15-xx and T27-xx. This Service Bulletin applies to both of these serial number designations as they both Model S2R- T15 airplanes. Model Serial Numbers S2R-R1340 R1340-0028 through R1340-035 Perform initial inspection at 2200 hours time in service (TIS). Group 3 Airplanes* Perform initial inspection at 6400 hours time in service (TIS). S2R-R1820 R1820-036 S2R-T65 T65-001 through T65-017 S2RHG-T65 T65-002 through T65-017 S2R-T34 T34-144, T34-146, T34-168, T34-169,T34-172 through T34- 179, and T34-189 through T34-232, T34-234, & T34-236* S2R-T45 T45-001 through T45-014 S2R-G6 G6-101 through G6-147 S2R-G10 G10-101 through G10-141 S2R-G5 G5-101 through G5-105 * The serial numbers of the Model S2R-T34 airplanes could incorporate T35-xxx, T36-xxx, T41- xxx, or T42-xxx. This Service Bulletin applies to all of these serial number designations as they are all Model S2R-T34 airplanes. Model Serial Numbers 600 S2D All serial numbers beginning with 600-1311D S2R 1380 and 1416R through 4999R S2R-R1340 R1340-001 through 1340-010, R1340-013 through R1340-018, R1340-021 through R1340-023, and R1340-026 S2R-R3S R3S-001 through R3S-011 * Any Group # airplane that has been modified with a hopper over 400 gallons, a piston engine greater than 600 horsepower, or any gas turbine engine makes the airplane a Group 1 airplane for the purpose of this Service Bulletin. The owner/ operator must inspect the airplane at the group 1 compliance time specified in the Compliance section of this Service Bulletin. Reason for publication: Ayres Service Bulletin No.SB-AG-39 was published to detect before failure, cracks in the wing spar assemblies of Ayres Thrush Agricultural Airplanes. The revision to the Service Bulletin defines the re-inspection interval for certain models after rework and redefines model effectivity and grouping. Compliance: Options 1) Perform SB-AG-39 as originally written. 2) Perform Ayres CK-AG-29 Part 1if necessary. 3) Add the "big butterfly" P/N 20211-09 and –11 in accordance with CK-AG-29 Part 2. By whom work may be performed: A & P Mechanic or Equivalent Revised inspection requirements: Based on findings from accomplishment of SB-AG-39 and damage tolerance analysis, the following Inspections are acceptable for all Groups of airplanes: Aircraft records: SB-AG-39A, dated December 12, 1997 Entitled SB-AG-39 INSPECTION INTERVALS, Accomplished __________________(date). Approval: The FAA and Ayres Corporation Work performed/Technique Mag. Particle Ultrasonic EddyCurrent Inspect only 500 hours 400 hours 450 hours Inspect, no cracks, cold work 1500 hours 1200 hours 1300 hours Inspect, no cracks, cold work, install big butterfly 2500 hours 1950 hours 2150 hours Inspect, small crack, cold work, to remove crack, re-inspect 950 hours 750 hours 825 hours Inspect, small crack, cold work, to remove crack, re-inspect, install big butterfly 1550 hours 1200 hours 1350 hours Weight and Balance: N/A Publications affected: SB-AG-39 Record of Compliance: Make appropriate airframe logbook entry.