SAFA Ramp Inspections Guidance Material (Version 2.0)

European Aviation Safety Agency

European Aviation Safety Agency

Approvals & Standardisation Directorate SAFA Coordination Section

SAFA Ramp Inspections

Guidance material

Version 2.0

SAFA Coordination Section Page 1 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspections Guidance material Table of Contents SAFA Coordination Section Page 2 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material SAFA Coordination Section Page 3 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspections Guidance material

1 Introduction

SAFA inspections are part of a European Union safety programme and shall be executed in a harmonised and standardised way in all EU Member States, in Iceland, Norway, and Switzerland, and in all States with which EASA signed a working arrangement on SAFA. For this reason the Annex to the Commission Directive 2008/49/EC calls for guidance material to give clear guidance and instructions to the inspectors performing SAFA ramp inspections.

Inspectors must have received training in their relevant field of expertise before performing any SAFA inspections; details can be found in the EASA Guidance Material on the Qualification of Inspectors.

This procedure contains guidance material as required by the mentioned Annex as well as guidance material in addition to those required. The following table is a cross reference between the paragraphs of the Annex and the chapters of this procedure.

Paragraph of the Annex to CD 2008/49/EC Ramp inspection procedure chapter 1.1 3.1 1.2 No guidance material 1.3 3.1h, 3.3 1.4 3.1f 2 Transposed in “Guidance material on qualification of inspectors” published 29 September 2008 3 3.4 4.1 3.1h, 3.3 4.2 3.3, Appendix 2 4.3 Appendix 1 4.4 No guidance material 5 5, Appendix 1 6.1 6.1.1 6.2 6.1, 6.2 6.3 6.1.1 6.4 6.1.2, 6.2.1, 6.3 6.5 6.1.3, 6.2.2

1.1 Definitions

State of oversight Either the State of Operator, State of Registration or State of Licensing (whichever is applicable) responsible for the oversight in that area (possibly transferred by an Article 83bis agreement) AMM Aircraft Maintenance Manual ATLB, Aircraft Technical Log Book, sometimes also TLB, indicated as TLB or short the aircraft’s Tech Tech Log Log CDL Configuration Deviation List CMM Component Maintenance Manual MEL Minimum Equipment List N/A Not available PDF or PDFs Pre-Described Findings POI Proof of Inspection SAFA Coordination Section Page 4 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material SDR Special Drawing Rights SRM Structural Repair Manual UDF User Described Finding U/S Unserviceable WSPM/WDM Wiring Diagram Manual

1.2 Standard Reports

1.2.1 Introduction Directive 2004/36/CE (“SAFA Directive”) in its Article 3 requires Member States to put in place a mechanism to collect any information deemed useful to establish and maintain a high uniform level of civil aviation safety in Europe. Such information shall include important safety information as referred to in Article 3(a), collected through several means and shall be kept using the Standard Report form.

The Standard Reports shall be exchanged with the Commission and the Member States as required by Article 5 of the SAFA Directive. In addition, those reports shall, in accordance with article 3.2 of Regulation (EC) No 768/2006, be communicated to the Agency. The Standard Reports are one of the sources of information to be taken into account when identifying which aircraft shall be subject to a ramp inspection.

Although Article 3 of the SAFA directive also requires that follow-up information as described under (b) and (c) of that Article shall be kept as Standard Reports, it is considered to be compliant if such information is recorded in the concerned Ramp Inspection Report and the monthly report on the status of follow-up actions (as referred to in Paragraph 6.4 of the Annex to Directive 2008/49/EC).

1.2.2 Exchanging Standard Reports Like Ramp Inspection Reports, Standard Reports can be entered into the centralised SAFA Database. By doing so, Members States are meeting the requirement of both using the Standard Report format and exchanging it with the other stakeholders. Any useful information like documents, pictures, etc. can also be stored in the database and linked to the Standard Report.

1.2.3 Disidentification of the source Important safety information might be received from passengers or whistleblowers. Although not specifically addressed by Article 6.4 of the SAFA directive, it is self-explanatory that information in the Standard Report should be disidentified to such extent that the source cannot be identified.

Examples of important safety related information could be, but not limited to, ATC reports on level- busts, communication failure or difficulties, and abnormal take-off lengths, information received from maintenance organisations concerning lack of AD compliance or maintenance work performed incorrectly, reports from the general public/whistleblowers concerning perceived unsafe situations, reports from pilots on incorrect use of radio-telephony phraseology, reports from airport personnel on observed unsafe practices, factual information concerning accidents and incidents which occurred in Member States’ airspace.

SAFA Coordination Section Page 5 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material SAFA Coordination Section Page 6 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspections Guidance material

2 SAFA Ramp Inspection and related processes - overview

2.1 General

Inspection Finding(s) Categorisation Follow-up a) The inspection process consists of different elements like the preparation of the inspection, the determination of which items need to be inspected and which standards to use. Chapter 3 contains guidance on these elements.

b) If during the Ramp Inspection a deviation from the applicable Standards is established, it is considered a finding. Guidance on findings can be found in chapter 4.

c) There are three different categories of findings, depending on the impact the finding has on the safety of the aircraft and/or its occupants. Chapter 5 provides guidance on the categorisation of findings.

d) Based on the outcome of the inspection and subsequent categorisation, follow-up actions and classifications have been defined. Details can be found in chapter 6.

2.2 SAFA National Coordinator

The SAFA programme coordination is performed by EASA in accordance with Commission Regulation (EC) No 768/2006. To facilitate the implementation of SAFA activities within each Member State, a coordination function is needed at a national level. A National Coordinator should therefore be appointed by each Member State tasked with the day-to-day coordination of the program at national level. The position of the “SAFA national coordinator” should not be confused with the “National coordinator” as mentioned in Regulation (EC) No 736/2006 (on the working methods for Standardisation inspections); however, as reflected in Appendix 7, it is strongly recommended that with regard to the domain of SAFA, the SAFA national coordinator should be taking up the role of the “standardisation” national coordinator.

The tasks and obligations that could be allocated to the SAFA National Coordinator are listed in Appendix 7. Please note that these duties may be allocated to different persons within the SAFA Coordination Section Page 7 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material SAFA participating State, however it is deemed important that the coordination of these duties is executed by the SAFA National Coordinator.

Besides appointing a SAFA National Coordinator, it is advisable to nominate a “Coordinator National Operators”. This person would, with regard to the operators under the oversight of his/her NAA, act as the focal point for the other SAFA Participating States.

SAFA Coordination Section Page 8 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspections Guidance material

3 SAFA Ramp Inspection

3.1 General instructions

a) The SAFA Ramp Inspection should preferably be performed by at least 2 inspectors. The main elements of the inspection, the visual inspection of the aircraft exterior, the inspection on the flight deck and the inspection of the passenger cabin and/or cargo compartments can be divided among the inspectors.

b) Inspectors are entitled to perform a SAFA inspection and search the aircraft according to Article 16 of the Convention on International Civil Aviation (search of aircraft): “… the appropriate authorities of each of the contracting States shall have the right … to search aircraft of other contracting States…”.

c) Should an operator refuse to permit the performance of a SAFA inspection without a valid reason, the competent authority should consider the detention of the aircraft (provided that the national legislative framework allows for this). In such a case, the competent authority must immediately inform the State of oversight.

d) In order to be able to inspect foreign aircraft operators, each authority should arrange direct access to the ramp or other relevant areas for their inspectors, or have made an arrangement with the applicable airport authorities on how to get such access. The authority should provide the inspectors with the necessary tools (e.g. flashlights, digital camera, mobiles) and protective clothing suitable for the environmental circumstances (e.g. fluorescent vests, ear protection, anti-static clothing).

e) Inspectors must show tact and diplomacy when performing a SAFA Ramp Inspection.

Any unnecessary contact with passengers should be avoided; however, this may be justified so as to be able to inspect certain elements in the cabin, such as: a. proper stowage of cabin baggage under the seat, b. overweight in overhead luggage bins, c. baggage in front of emergency exit, d. infants/children over the minimum age determined by the State of oversight should have their own seat, e. passengers repartition in the cabin, compared to the loadsheet data, f. sufficient number of seats, g. observing the boarding process during normal operations, during refuelling in progress.

f) Departure delay of an aircraft should be avoided. However, when an inspector discovers an issue which may have a major effect on flight safety or requires further investigation to be clarified, a delay may be justified, for example: a. the tyres appear to be worn beyond the limits (central groove no longer visible), however reference must be made to the applicable AMM to determine the actual limit; b. an oil leakage (e.g. 5 drops/minute) must be checked against the applicable AMM to determine the actual limit; c. a flight crew member cannot produce his/her licence. Clarification must be sought from the operator to confirm that the flight crew member has a valid licence by requesting, for instance, a copy of the licence to be sent to the inspectors for verification.

Note: the limitations quoted in the examples are here for illustration purposes and should not be applied during a ramp inspection, knowing that the defects raised must be studied in SAFA Coordination Section Page 9 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material respect of the limitations enacted in the applicable documentation of the inspected airline g) A certain amount of inconvenience to flight and cabin crews, handling agents and other personnel involved in ground handling activities may arise, but inspectors must do everything possible to reduce hindrance to the minimum, for example: a. they should try to be as precise and complete as possible when asking for A/C documents from flight crew. This should result in a minimum of discussion time allowing the flight crew to deal with their primary task of flight preparation; b. they should ask the senior cabin crew member to dedicate one crew member to assist them with the inspection tasks; c. they should debrief the commander of the aircraft after the inspection task is completed; d. they should inform cargo loading staff of possible hindrance due to inspection task in cargo compartment; e. when carrying out inspections on the flight deck, the flight crew should be allowed to give priority to staff directly involved in the flight preparation (e.g.

fuel master, load-planning agent, handling agent pax. info, etc.).

h) SAFA inspectors should try to perform all of the SAFA checklist items. When circumstances prevent this (time, manpower, etc.), try to inspect those elements which, according to inspectors’ preparation and experience, are likely to be more safety critical: this is depending on the particularities of the inspected flight. Elements to be taken into account are: a. In general, certain elements are less safety critical. E.g. a noise certificate has far less impact on safety than incorrectly completed Mass & Balance documentation (or incorrect calculation) and should therefore be given a lower priority.

b. The difference in the aircraft configuration. Whereas for a cargo configuration the securing of the cargo and the segregation of the dangerous goods is important, for a passenger configuration refuelling with passengers on board could have a higher priority.

c. Previous SAFA results. If serious and/or recurrent findings were raised during previous inspections on e.g. the MEL, this might become more important than the flight preparation on which previously no non-compliances were found.

d. Type and age of the aircraft. Some aircraft types are known to have issues with e.g. leakages or missing screws. Age of the aircraft could be of influence as well.

i) Nothing should be done in the course of a SAFA Ramp Inspection that hinders the crew/passengers that could just as well be inspected on another aircraft of the same operator without causing delay/hindrance.

j) Whenever possible, it is advised to contact the operator’s representative at the airport so that he/she can be present during the SAFA Ramp Inspection. Experience shows that the operator’s representative may be helpful in providing support especially in facilitating communication with the crew or operator home base.

3.2 Inspection preparation

The inspection preparation procedure includes three main elements:  selection of the aircraft/operator to be inspected;  information gathering about the aircraft and the operator;  preparation of the inspection itself.

SAFA Coordination Section Page 10 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material The inspection preparation procedure described above is designed primarily to cater for pre- planned inspection, however for non-planned inspections (e.g. spot-check, focussed and follow-up inspections) the same procedure should be followed as far as practical.

3.2.1 Selection criteria According to Article 4 of the Directive 2004/36/EC, Member States “shall put in place the appropriate means to ensure that third-country aircraft suspected of non-compliance with International safety standards (…) shall be subject to ramp inspections”. This can be achieved by long term planning (for those operators of which the suspicion as well as the arrival date is known well in advance) or a short term planning (where information leading to the suspicion and/or information on the arrival date and time is not known on the long term). The information sources which could be useful for identifying the suspected aircraft are mentioned in Article 4.1 of the before mentioned Directive, and the most useful ones for establishing a schedule are repeated under points a. and b. below. In addition to this obligation, Member States may also perform checks at random (“Spot checks” in the absence of any suspicion).

Notwithstanding the above, Member States shall prioritise their ramp inspections on the subjects included in the list referred to in Article 3 of Commission Regulation (EC) No 351/2008, since the aircraft/operators in this list are by definition “suspected”. The SAFA Database contains a module where information about prioritised subjects can be easily retrieved.

Member States should plan their activities by establishing a schedule for the performance of SAFA inspections. This schedule is the competent authority’s responsibility.

The schedule may consist of: a. Long term planned inspections Operators performing scheduled operations could be selected on a long-term basis for inspections, since their schedule is known to the competent authority. Information leading to a suspicion could originate from (e.g.): o previous ramp inspections performed on this operator; o previous prioritisation lists, indicating that the operator or the State of operator is already suspected for a longer time; o Standard Reports according to Paragraph 1.2.

b. Short term planning Short term planning should be used when information, leading to a suspicion, is received on a short-term. Such information might be originating from (but not limited to): o previous inspections done by the Member State; o the SAFA database (inspections performed by other Member States); o passenger complaints; o Air Navigation Services Providers (reports that an aircraft has performed abnormal manoeuvres which give rise to serious safety concerns since entering the airspace of the Member State); o “whistleblowers”(ground handling or maintenance personnel) regarding poor maintenance, obvious damage or defects, incorrect loading, etc.; o evidence that the State in which an aircraft is registered may not be exercising proper safety oversight; or SAFA Coordination Section Page 11 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material o concerns about the operator of the aircraft which have arisen from occurrence reporting information.

Short term planning should also be used to verify compliance, in absence of any suspicion, when new operators, any new type of operations or new type of aircraft being introduced, following information received from the department granting traffic rights.

c. Spot checks Provided that the Member State has established rules to carry out random (spot check) inspections, Ramp Inspections may be carried out in the absence of any suspicion of non-compliance. Such rules should contain at least the following principles: o repetitive inspections should be avoided on those operators on which previous inspections have not revealed safety deficiencies, unless they form part of a series of partial inspections (due to time limitations) with the intention to cover the complete checklist; o the selection would enable the widest possible sampling rate of the operator population flying into their territory; however, some airlines are only operating flights to a very limited number of States (if not even to only one sometimes).

The involved States should consider inspecting regularly those subjects – even more if these airlines also appear on the prioritisation list; o no discrimination based on the nationality of the operator, the type of operation or type of aircraft.

3.2.2 Data collection Using the information sources in 3.2.1b, the competent authority should build a knowledge file on the operator. Such a file would enable the inspector to:  Verify the rectification of previously found non-compliances  Select the items to be inspected if the time available does not permit a full inspection The SAFA database has a special “preparation of inspections” module to allow for a comparison between operators in a given span of time as well as a quick determination of the number and type of findings on a specific operator over a specific time. This might be useful when the inspector has to choose between several operators arriving at the same time.

3.2.3 Preparation of the inspection After the aircraft/operator has been selected and all the available information is collected, the next step is the preparation of the inspection itself.

The following steps should be taken shortly before the planned inspection:  Last update of the operating schedule for the selected operator should be obtained from airport, operators, or ground handling officials ( see Note 1 );  Distribute the tasks between the SAFA inspectors involved, especially in the case of a limited inspection time and/or the size and the complexity of the aircraft; SAFA Coordination Section Page 12 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material  Select the checklist items to focus on taking into account the General instructions in paragraph 3.1h;  There should be co-operation with security, ground and all other officials involved in airport activities, to enable the SAFA team to reach the aircraft to be inspected (see Note 2 );  For planning purposes, EUROCONTROL has a special module in which you will be able to find relevant flight information concerning any targeted operators. The application form to request access to the CFMU system can be found on their website .

Note 1 : In general, the operators issue operating schedules twice per year. However, there might be “last minute changes” to these; therefore, SAFA team members should ensure they have the latest update of the schedule. A valuable source can be the internet; most airports have a website displaying information on arrival and departure times of scheduled flights.

Schedule information on special flights such as cargo, unscheduled or private flights, may need to be specifically requested from the airport.

Note 2: Where officials from different organisations (i.e. customs, security, DG inspectorate) have to work in co-operation during the inspection, a procedure on cooperation may need to be developed at a National level. There is no standardised method as most Member States have different airport procedures for SAFA inspectors.

3.3 SAFA inspection items

The SAFA Ramp Inspection checklist (mentioned in Annex II to Commission Directive 2008/49/EC) contains a total of 54 items. Of these checklist items, 24 relate to operational requirements (A-items) to be checked on the flight deck, 14 items address safety and cabin items (B-items), 12 items are concerning the aircraft condition (C-items) and 3 items (D- items) are related to the inspection of cargo and the cargo compartment. In case of any findings not related to the other items of the checklist, they may be administered by the E- item (General) of the checklist.

The inspection findings and subsequent categorisation have to be reported on the SAFA Ramp Inspection Report after completion of the inspection, even if there are no findings raised. The instructions on the completion of the Ramp Inspection Report can be found in Appendix 2.

Depending on the time available for the SAFA Ramp Inspection not all items but a limited number of items may be checked (see General instructions in 3.1 h).

Depending on the items to be inspected, a SAFA Ramp Inspection may be performed on landing or on departure of the aircraft. Fuel remaining and cargo area (overloading, restraining, segregation, etc.), are examples of items that could be checked on landing.

Flight preparation and storage of baggage in the cabin could be checked on departure.

However, inspectors should be aware of the following constraints; an inspection after http://www.cfmu.eurocontrol.int/cfmu/public/standard_page/userdocs_forms_sysaccess_fornonansp.html .

SAFA Coordination Section Page 13 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material landing should not jeopardise the total resting time of the flight crew and an inspection prior to departure should not lead to a departure delay unless there is a good reason (see paragraph 3.1.f).

For each inspection item of the SAFA Ramp inspection report detailed guidance has been established (see appendix 1, SAFA PDFs). This guidance specifies in more detail what to inspect and how to categorise it. In addition, references are made to the applicable standard(s). The list of PDFs is not exhaustive and other findings may be raised by the inspector (see Chapter 5c).

3.4 Standards

a) The purpose of a SAFA inspection is to check the compliance with international standards (i.e. Chicago convention, its Annexes and ICAO regional standards) which are the minimum standards to be observed by any aircraft engaged in international navigation. In addition, when inspecting the technical condition of an aircraft, it should be checked against the aircraft certification specifications and manufacturer’s standards . Furthermore, compliance with national standards that are declared applicable to all operators flying to that state may be checked.

b) The applicable standard has to be reported on the ramp inspection input form when a finding has been raised. When other standards are being checked during a SAFA Ramp Inspection and a finding has been raised, the standard should explicitly be stated in the Ramp Inspection Report (e.g. when a Ramp Inspection Report is included in the SAFA database containing a finding which is a non-compliance with a national standard, the competent authority should ensure that the standard is marked as ‘N’ = national standard).

c) The SAFA database has the possibility to incorporate findings not (yet) contained within the PDFs. When making a new description mention should be made of the applicable standard and its correct reference, for example: found cracked bearing in nose gear retraction cylinder, standard M, reference AMM 32.xxx.

d) For findings where a PDF is available, and especially for UDF, the applicable standard reference (when not already specified) should be entered as precisely as possible. This should be particularly applied when findings are raised against manufacturer's standards or aircraft certification specifications.

Contained in a set of documents issued by the aircraft TC holder which detail the conditions for the serviceability of the systems and components installed on an aircraft, e.g. AMM, SRM, CMM, SWPM/WDM.

SAFA Coordination Section Page 14 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspections Guidance material

4 SAFA Findings

4.1 General

A finding is a non-compliance with an applicable standard (see paragraph 3.4 [STANDARDS]). Inspectors, when raising a finding, must avoid using “best practices”, company procedures or standards other than international safety standards they were used to in any other duty or employment.

When a deviation from a standard has been determined, the inspector should be certain that the finding is applicable to the specifics of the inbound and/or outbound flight. For instance, having no electric torch on board is only a finding during night-flight operation and not enough life-vests only when required as per the provisions of Annex 6, part I, Chapter 6.5.2.1 and 6.5.2.2 (i.e. flight over water on a distance greater than 50 NM from the coastline…). Nevertheless, such kind of information should be reported as a General Remark.

When a Contracting State finds it impracticable to comply with an international standard, it is entitled to notify a difference to ICAO in accordance with Art. 38 of the Chicago Convention . However, a third country notification of a difference has no effect within the territory of another Contracting State, and merely constitutes information to other Contracting States which might accept or not such lower standard: SAFA ramp inspectors should indeed raise a finding in case of non-compliances .These differences may however be taken into account in the follow-up process of the ramp inspection report (as detailed in the follow-up procedures). Whenever EU standards are lower than ICAO standards, then the EU standards should be applied to EU and non-EU operators .

If after the inspection the operator or its State of oversight is providing documented evidence objectively indicating that the finding is erroneous or incorrectly categorised, then the inspecting authority should make the necessary corrections in the SAFA Database and inform the operator and/or its State of oversight accordingly.

Art. 38 Chicago Convention has the purpose to protect the sovereignty of a Contracting State by granting the right to derive from an international standard. International standards cannot become binding against the will of ICAO Contracting States. However, ICAO contracting States are not bound by or obliged to accept a lower standard of another State’s aircraft in their territory even if the latter notified the difference according to Art. 38.

On another State’s territory the differing State is obliged to: fulfil the international (ICAO) standard (Art.

37 in conjunction with Art. 33 of the Chicago Convention), or to get permission (ex-ante authorisation) by the State in whose territory the aircraft intends to enter to participate in air navigation with a certificate or license that was issued although the aircraft (respectively person) failed to satisfy an international (ICAO) standard at the time of its certification (respectively issuance of the license), see Art. 39 in conjunction with Art. 40 of the Chicago Convention. If the above-mentioned permission has been duly requested and delivered by the Inspecting NAA, the non-compliance should however be reported as a General Remark - cat G.

For instance, EU-OPS is requiring the presence of a copy of the AOC to be on board of an aircraft, while ICAO standards require the presence of a certified true copy of the AOC. Absence of certified true copy should not constitute a finding (provided a non-certified copy is available on board).

SAFA Coordination Section Page 15 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material When following the procedure as described in chapter 4.2 f) below, the category 2 findings raised (failure to identify, report and or assess significant technical defects) should be grouped as long as it concerns the same system and “root cause”; if not, findings should be reported separately with the exception of missing fasteners. The number of (out of limits) missing fasteners (and therefore the related category 3 findings) found during one inspection could be considerable. However, this high number of cat 3 findings would not reflect the perceived impact on safety. Therefore, findings on missing fasteners in the primary structure should be grouped and reported as one finding; the same for the missing fasteners in the secondary structure.

With regard to non-compliances on missing fasteners, findings can only be raised if the maintenance documentation contains clear limits and/or dispatch conditions. In the absence of such clear manufacturer standards, inspectors should only raise findings if their expert judgement (possibly supported by licensed maintenance personnel) is such that similar circumstances on comparable aircraft would be considered to be out of limits.

A SAFA ramp inspection aims at assessing the compliance with the applicable international standards of an aircraft used in operations. It should be noted that several other entities are playing a crucial part in this process, such as the authority of oversight of the AOC, the authority issuing the flight crew Licences, the authority of oversight of the airworthiness of the aircraft. Therefore, some non-compliances may be highlighted in fields where the inspected airline may not be the responsible entity (e.g. issue of certificates of registration, issue and oversight of the AOC or Licences). Nevertheless, as part of the ramp inspection process, these non-compliances will be raised by the inspectors in accordance with the SAFA ramp inspection procedures, and recorded as such in the final report of the airline’s inspection.

When inspectors are raising issues on the ramp that may lead to the identification of findings, they should, as much as possible, document and keep records of the non- compliances detected. This could be done, for instance, by taking pictures of the deficiency itself, as well as pictures of the manufacturer references used to assess the technical defects, pictures or copy of the TLB entries performed. These elements could be very useful in the follow-up phases of the ramp inspection either to explain in details and illustrate the finding detected, or to be able to exchange appropriate documented evidence when findings are challenged.

Note 1: In exceptional cases, a single fault may give rise to more than one finding under different inspection items, for example: a tyre worn beyond limits whilst the commander refuses to enter the defect in the Technical Log (or equivalent) would give rise to findings under C04 and A23.

Note 2: On manufacturer standards, a finding to these standards should always be demonstrated in relation with aircraft technical documentation (AMM, SRM, CDL, SWPM, etc.)

and MEL references. If significant defects are suspected, the operator should be asked to demonstrate compliance with the standards. Deviations from these standards can only be acceptable if the State of oversight has issued a formal waiver/concession detailing conditions and/or limitations to allow the aircraft to continue to operate for a specific period of time before final repair, unless the aircraft will perform a ferry flight and the validity of the CofA is not affected. In case the deviation leads to a temporary invalidation of the Certificate of Airworthiness, the operator will be required to obtain a permit to fly from the State of Registry, and the relevant permission from the affected States (departure, arrival and every overflown States).

SAFA Coordination Section Page 16 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material Note 3: Certain States may have national standards applicable to foreign operators when operating in their territory. Deviations from such standards should be reported as findings only if: - the national standards have been published (e.g. AIP) and are applicable to foreign operators flying into their territory; - a deviation from those standards has an impact on safety.

For such findings the report should indicate ‘N’ in the column Std. and the appropriate reference should be included in the column Ref .

Any other deviation from national standards which does not have an impact on safety (e.g.

insurance certificate in USD instead of SDR) should be recorded as cat. G (General Remark).

A participating State should issue internal procedures for the use of its inspectors on what national standards and how compliance with those standards should be checked, and how any possible findings should be categorised.

4.2 Detection/reporting/assessment of significant technical

defects

A technical defect is considered to be any material fault pertaining to the aircraft, its systems or components. Minor defects are typically without influence on safety. Although minor defect are not considered to be findings, they should be brought to the attention of the operator using general remarks (cat. G). Those defects which are potentially out of limits are considered to be significant defects. Further assessment is required to determine if the significant defect is within or outside the applicable limits. Such defects should be known to the operator since they should have been detected during regular maintenance, aircraft acceptance procedure or pre-flight inspections.

Care should be taken when dealing with technical defects which did not necessarily had to be detected by the operator since the approved maintenance programme (AMP) does not require the operator to detect such issues during turn-around inspections; examples are missing fasteners, bonding wires and the cabin emergency lighting which are normally not part of the pre-flight inspection. Therefore, no finding should be raised under A23/A24 that such defect was not detected/reported/assessed. However, inspectors should not ignore cases where those defects led to an out of limits situation; apparently the AMP failed to ensure that the aircraft is in an dispatchable condition and therefore such non-compliance should be raised as a cat. 3 finding.

Since significant defects might have appeared during the inbound flight, the inspector must give the operator the opportunity to identify and assess a significant defect during the preflight inspection before he raises a finding. However, this does not mean that the inspector should wait with his inspection of the aircraft condition until the operator performed/completed the preflight inspection.

A “defect within limits but not recorded” should not be raised as a technical finding. If the significant defect appeared to be within limits, the safety focus changes from the defect itself to the concern that the defect was not detected/assessed by the operator.

The following procedure should be used (see also the flowchart below) in particular when inspecting the Aircraft Condition. In addition, the same procedure may also be applied when inspecting items A, B or D: a) If time allows, the inspector should inspect the aircraft condition after the operator has completed the preflight inspection.

b) The inspector may perform the aircraft condition inspection (C-Items) in advance of the operator’s inspection in order to make best use of the time available for the whole SAFA Coordination Section Page 17 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material inspection. In that case the inspector should wait with reporting the defects identified until the operator has completed the pre-flight inspection.

c) The inspector should subsequently check if the operator detected the significant defects found by the inspector. Examples of significant defects are, but not limited to, multiple screws missing in the corner area or in the leading edge of panels, running/dropping leaks, dents in pressurised areas of the fuselage. A single screw missing in the middle of a fairing, traces of old leaks and non-structural damages to e.g. fairings can, in many cases, considered to be “minor defects”. Such defects should be brought to the attention of the operator as general remarks (cat. G).

d) If the operator detected the significant defect, but did not properly report and/or assess it, the operator should assess the defect. If the defect appears to be within limits, a finding should be raised under A23 (Defect notification and rectification) mentioning “Known defect not reported/assessed”. The inspector should however, when collecting the evidence for this finding, take into account the reporting system used by the operator. For instance, if the operator uses a Technical Logbook and/or a damage chart, a finding could be raised if the defect was not entered. Additionally, a category “G” (general) remark should be created for the defect. If the defect is outside limits, a category 3 finding should be raised under the respective inspection item. In order not to penalise the operator twice, no supplementary finding, related to this defect, should be raised in that case under A23.

e) If the operator did not detect the significant defect, the inspector should inform the crew on the non-identified defects. Subsequently, the operator should assess the defect in order to determine if the defect is within or outside dispatch limits. If the defect is within limits, a category 2 finding mentioning “Pre-flight inspection performed but without noticing significant defects” should be raised under A24 (pre-flight inspection) addressing the deficiency that the defect was not detected. Additionally, a category “G” (general) remark should be created for the defect. If the defect is outside limits, a category 3 finding should be raised under the respective inspection item. In order not to penalise the operator twice, no supplementary finding, related to this defect, should be raised in that case under A24.

f) Multiple (Cat 2) findings on the same system (e.g. hydraulic leakage, fuel leakage, dents) and “root cause” (not identified, not reported or not assessed) raised under A23 or A24 should be grouped. E.g. dents on the LH wing and the #2 engine intake which were not identified should be grouped, as well as hydraulic leakages which were identified but not assessed. On the other hand, a fuel leakage on the left wing which was not identified and a fuel leak on Engine #2 which was reported but not assessed should be noted as two findings. As described in chapter 4.1.

g) An unnecessary delay of the aircraft should be avoided. However, if the aircraft suffers a delay caused by the assessment of not properly assessed/not identified findings, such a delay is justified according to paragraph 1.4 of the Annex to the Commission Directive 2008/49/EC where it is mentioned that possible causes for delay could be “(…) doubts regarding the (…) airworthiness of the aircraft (…)”.

Even when operators are carrying out their pre-flight inspection (aircraft acceptance) procedures only briefly before the departure of the aircraft, the inspector should wait until these procedures have been completed before reporting to the operator the identified defects. Although an investigation, which may trigger delays, might subsequently be required once the inspector has informed the airline of the missed technical defect, the airline procedure would have resulted in the same delays if the flight crew would have identified the same defect requiring the associated investigation. Therefore, it is the operator which takes the risk to perform the pre-flight inspection close to departure; as Inspectors should use the ATA system taxonomy (e.g. Chapter 28 Fuel, Chapter 32 Landing gear) to determine if findings are related to the same system.

SAFA Coordination Section Page 18 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material long as the SAFA ramp inspectors are acting in accordance with the §3.1f) of this guidance material, the operator is responsible for any consequences linked to delays (including cancellation of flights) imposed by the assessment of missed technical defects.

SAFA Coordination Section Page 19 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material SAFA Coordination Section Page 20 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material

4.3 Assessment of findings on certificates and licenses prior to

categorisation

The procedure described in Chapter 4.2 already applies the principle that, before categorising findings, a proper assessment of the encountered situation should be done. Only when it is clear to the inspector the extent to which the non-compliance deviates from the requirements, can a proper category of the finding be chosen. This implies that inspectors should not raise category 3 findings with the only intent to enforce further investigation/assessment.

The before-mentioned principle should be applied in other inspection areas as well. E.g. in some cases, the absence of a licence or certificate could potentially have a major impact on safety; however, after receiving the appropriate evidence , it may become clear that the impact on safety is less than initially foreseen. A typical example is where the licence of a member of the flight crew is not on board. If before departure evidence is provided that the crew member is indeed holding an appropriate and valid licence, but simply did not carry this licence, the impact on safety is lesser and the category 1 finding “Flight crew holding appropriate Licence but not carried on board at the time of the inspection” should be raised. If such evidence is not provided before departure, the category 3 finding “Flight crew without appropriate licence” requiring corrective actions before the flight is authorised. Under no circumstances, a flight crew member should be permitted to perform flying duties without receiving confirmation that s/he has been issued an appropriate and valid licence.

A similar approach could be used for the aircraft documents (certificate of registration, airworthiness, radio station licence) and the airline’s authorisations (AOC and OPS Specs), although issues detected on these certificates may not always lead to the identification of category 3 finding on the ramp (certificate of registration or radio station license for instance).

4.4 Deficiencies under the control of the operator

Non-compliances which are under control of the operator (in accordance with the applicable requirements) are not to be raised as findings. If e.g. an aircraft diverted because of technical defects and the aircraft is inspected upon arrival, such defects should not be raised during a ramp inspection following the diversion as long as the defect is properly reported (e.g. through the TLB) and subsequently assessed.

9 th See also chapter 6.1.3, 4 paragraph.

SAFA Coordination Section Page 21 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspections Guidance material

5 SAFA - Categorisation

If d uring the inspection it is established that a certain situation is not in compliance with the relevant standards, this is then considered a finding as defined in Chapter 4.

a) For each inspection item, 3 categories of possible deviations from the standards have been defined. The findings are categorised according to the perceived influence on flight safety. This means that a category 1 finding is considered to have a minor influence on safety. A category 2 finding may have a significant influence and a category 3 finding may have a major influence on safety.

Note: Any other safety relevant issues identified during a SAFA inspection, although not constituting a finding, can be reported as a General Remark (Cat G) under each inspection item, for example: an electrical torch missing or unserviceable during a flight conducted entirely in daylight.

b) The finding should be categorised according to the list of PDFs in appendix 1. In the SAFA PDF list the description, categorisation and reference to the applicable standard is given. Although the list of PDFs is as complete as possible, it cannot cover all possible deviations that may occur.

c) The SAFA PDF list is intended to be used by the inspector to guarantee a common description and categorisation of findings. The inspector should make use of this list in the majority of situations and should always privilege the use of PDF while reporting SAFA findings in the SAFA database. In those cases where there is no appropriate PDF, the inspector should, based upon his proficiency and the impact on aviation safety, make a sound judgement into which category the finding needs to be placed. The SAFA database allows for findings to be entered by the user. While inserting an UDF in the SAFA database, the inspector should make sure to always report the associated Standard Reference representing the basis for the identification of the finding. These UDFs will be monitored by EASA periodically and after evaluation may become part of the existing PDF list. Therefore the PDF list will be updated periodically. Notice of updates will be given via the appropriate channels to the SAFA community.

d) Findings on arrival flights being identical to the findings raised for departure flights should lead to the same categorisation, although the corrective action might not be possible when the flight has been completed. For example, an incorrect mass and balance sheet (outside operational limits) found on arrival should be categorised as a cat. 3. Obviously this cannot be corrected; however the appropriate class 3 action could be to confirm that the mass and balance calculations are within operational limits for the outbound flight.

e) In exceptional cases, where multiple findings have such an interrelation that the impact on safety is higher, the category of such findings may be increased to reflect the impact on safety. The increase in category should be explained in the detailed description of the finding.

SAFA Coordination Section Page 22 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspections Guidance material

6 SAFA – Follow-up actions

Chapter 6 of Annex II to the Directive 2004/36 (as amended by the Directive 2008/49) requires that follow up actions will be taken after the SAFA Ramp Inspection. The follow-up actions may be distinguished in two stages. The first stage is the follow-up action directly resulting from the findings, the second stage is the monitoring and follow-up of any correspondence, sent out to the operator and the State of oversight, which should result in closure of the findings.

6.1 Actions resulting from an inspection

Based on the results of the inspection and on how the findings have been categorised, common follow-up actions have been defined. The relations between the category of findings and the resulting class of actions to take are given in Chapter 7, Appendix 3 (class of actions matrix).

This chapter repeats the requirements to hand over the Proof of Inspection to the flight crew and to have a written communication with the operator and its competent authority. Although crews, operators and authorities become more and more familiar with the SAFA programme, it might be necessary to inform them about the SAFA programme and to explain them what is expected from their side when an inspection has been performed. For this purpose two templates for information leaflets are proposed in Appendix 4; one for the operator and its competent authority and one for the general public. These leaflets may be e.g. handed out to the flight crew, may be attached to the written communication sent to the operator or handed out to the passengers in case they raise questions about the inspection performed.

The inspecting authorities are invited to adhere as much as possible to these templates in the interest of standardisation and harmonisation. Contact details for the inspecting authority should be added to the last paragraph of the leaflet.

6.1.1 Class 1 action: information to the captain A class 1 action is to be taken after each inspection, and consists of providing information about the results of that SAFA inspection, regardless of whether findings have been identified or not. In accordance with article 6.3 of the before mentioned Annex, this is achieved by a verbal debriefing and the delivery of the Proof of Inspection (POI) to the aircraft commander (or, in his/her absence, to another member of the flight crew or the most senior representative of the operator). When completing the POI, the following should be taken into account:  The POI does not require the category of the finding to be mentioned. However, every Member State may decide to include more information to be shown on the POI than the minimum required (e.g. the delay incurred as a result of the inspection). Member States may choose to add the category of the finding in order to inform the flight crew as complete as possible on the inspection results.

 Only the issues mentioned in the POI should be reported as findings in the final SAFA ramp inspection report. Any other relevant information which was not included in the POI should only be reported in the final SAFA RI report as a General Remark or in the additional information box.

 When handing over the POI to the commander/operator representative, the inspector should ask him/her to sign the POI whilst explaining that the signature does not mean that he/she agrees with the findings. The signature only confirms that the POI has been received by the commander/operator representative.

SAFA Coordination Section Page 23 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material 6.1.2 Class 2 action: Information to the authority and the operator Category 2 and 3 findings are considered to have a significant and major influence on safety. Therefore, when category 2 and/or 3 findings have been raised, written communications must be made in accordance – with Article 6.4 of the above mentioned Annex – to both:  The operator: The communication should request that corrective actions are taken (or alternatively the provision of a corrective action plan) and evidence supporting the corrective actions taken; in case of no focal point is known for the inspected operator, its Quality department might be the most suitable point of contact.

 The state of oversight: The communication shall contain, where appropriate, a request for confirmation that they are satisfied with the corrective actions taken by the operator. This might be appropriate, for example, but not limited to: i. a high number of findings, ii. repetitive findings, iii. lack of appropriate response from the operator, iv. where there is evidence of consistently poor standards demonstrated by operators from that State, v. where action by the State of oversight may be required given the seriousness of the findings.

The state of oversight should also be informed when certain findings indicate possible shortcomings at state level (e.g. medical certificate does not indicate the medical class).

Note: In Appendix 5, guidance is given on the content of the written communication and templates are provided for written communication to the operator and its authority.

The primary source of information to enable an operator to take swift action to address safety deficiencies is the POI. In order to inform the states of oversight in sufficient time to permit appropriate action to be taken and to confirm to the operator the findings made, these communications should be made not later than 30 working days after the inspection.

In the case where the operator has already replied, to the satisfaction of the competent inspecting authority, based on the information contained in the POI, the written communication to the operator might not be required to be sent.

Note: In exceptional cases where multiple category 2 findings have been found and the accumulation of these findings or their interaction justifies a corrective action, the class of action may be increased to a class 3 action.

6.1.3 Class 3 actions: Restrictions or corrective actions A class 3 action follows a category 3 finding which are considered to have a potential major effect on the safe operation of the aircraft. For that reason, Article 6.5 of the said Annex requires that action(s) need to be taken before the departure of the aircraft. On the ramp inspection report only the actions required/imposed by the inspector should be mentioned.

If the operator voluntary corrected a cat. 1 or 2 finding before the flight, this should not be reported as a class 3b action. Instead, such voluntary action should be mentioned in the “Additional information box”.

SAFA Coordination Section Page 24 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material If the category 3 (major) findings that have been established during the SAFA Ramp Check concern damage of a nature such that the aircraft is no longer airworthy, this has to be communicated immediately to the State responsible for overseeing the airworthiness of the aircraft. Although the first contact may be, as a matter of urgency, accomplished by telephone, it is advisable to use written communication procedures. For ICAO guidance on this matter, refer to ICAO Annex 8 Part II Chapter 3.5 – Temporary Loss of Airworthiness.

Evidence related to findings on licences and certificates should be provided by the issuing authority. However, if the inspection is performed outside regular opening hours of the issuing authority, the inspecting State may decide to accept evidence from other sources as well, provided that the inspecting State seeks confirmation of the validity of such evidence at the earliest opportunity with the issuing authority. The ramp inspection report should mention which evidence was provided and by whom, including subsequent confirmation from the issuer.

The class 3 action is divided into 4 sub-actions: Class 3a. Restriction on the aircraft flight operation The inspector(s) performing the ramp inspection have concluded that, as a result of some deficiencies identified during the inspection, the aircraft may depart only under certain restrictions. Some examples of class 3a actions are:  restrictions on flight altitudes if oxygen system deficiencies have been found,  a non-revenue flight to the home base if allowed for by the MEL,  some seats that may not be used by passengers,  a cargo area that may not be used.

Class 3b. Corrective actions before flight The ramp inspector(s) have identified some deficiencies that require corrective action(s) before the intended flight. Such corrective actions may be:  (temporary) repairs to defects according to the AMM,  recalculation of mass and balance, performance calculations and/or fuel figures,  a copy of a missing Licence/document to be sent by fax or other electronic means,  proper restraining of cargo.

Class 3c. Aircraft detained by inspecting National Aviation Authority An aircraft is grounded in a situation where the category 3 (major) findings are not corrected by the operator before flight. Because the safety of the aircraft and its occupants is at stake, the aircraft has to be prevented from resuming its flight and has to be ‘grounded’ until the safety hazard is removed. This class of action should be imposed only if the crew refused to take the necessary corrective actions or to respect the restrictions on the aircraft flight operation. A class 3c action would also be appropriate when an operator refuses to permit the performance of a SAFA inspection without a valid reason (see paragraph 3.1 c), provided that the Inspecting NAA has set forth provisions in its national regulation covering this case.

Class 3d. Immediate operating ban In case of an immediate and obvious safety hazard a competent authority may react by imposing an operating ban on an operator or an aircraft.

SAFA Coordination Section Page 25 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material

6.2 Further follow-up

In the case where category 2 or 3 findings have been found, the related action(s) should have been taken. The follow-up however does not end there, further follow-up and/or monitoring is required.

Based on the acceptance by the Inspecting Member State of the differences notified to ICAO by other States, the finding raised during this ramp inspection could be considered as closed in the follow-up part of the process of the ramp inspection, without being provided with detailed corrective and/or preventive actions from the inspected airline or its associated competent authority. As far as the SAFA ramp inspections are concerned, acceptance by Member States of differences has to be done in a uniform and harmonised manner and should be coordinated by the Agency with all the SAFA States.

6.2.1 Class 2 action The class 2 actions comprise of communications to be made to the operator and to the State of oversight.

 Communication to operators: This communication always need further follow-up since they should contain a request for corrective actions taken or planned. The Member State should monitor if a reply is received and if it gives sufficient reason to close the finding(s) or prompts the need to request further information. In order to close the finding, the reply of the operator does not necessarily need to contain evidence that the deficiency has been corrected; the “corrective action taken” by the operator might also be the implementation of a corrective action plan. It is up to the Member State to decide, based on the related risk and impact, whether or not a finding may be closed based on future corrective actions taking into account the severity and recurrence of the detected findings. Depending on the severity and recurrence of the findings detected, the Inspecting NAA may consider the actual closure of the associated report(s) only after having received satisfactory documented evidence of appropriate implementation of preventive actions.

 Communication to authorities: The communication is primarily meant to inform the State of oversight; no reply is expected to these communications. Only where appropriate, the State of Oversight should be asked for “confirmation that they are satisfied with the corrective actions taken” by the operator. In this case, the Member States should monitor if such a reply is received and if the content is satisfactory.

Any follow-up communication from the operators and the authorities should be acknowledged and they should be informed about the closure of findings. Any request for clarification should equally be responded by the inspecting authority. The feedback or clarifications from the Inspecting authority should be performed within 30 working days.

If communications are taking place with the operator only, the State of oversight should, as much as possible, be copied with the associated replies from the Inspecting authority, as these elements can be very valuable in its oversight activities. It is especially the case for the information on the closure of ramp inspections findings sent by the inspecting authority to the inspected operator (when the latest is sent either by e-mail or official letter).

The operator should be allowed 30 days to reply. In case the operator does not react to the initial communication, the contact details should be verified followed by another attempt to obtain a reply from the operator whilst copying the competent authority in the State of Oversight. If this is again unsuccessful, that competent authority of the operator should be requested to intervene by encouraging the operator to reply. In the request, the inspecting SAFA Coordination Section Page 26 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material authority should explain that no reaction from the operator could be interpreted as a “lack of ability and/or willingness of an air carrier to address safety deficiencies”.

Findings should remain “open” as long as no satisfactory response of the operator and/or the competent authorities in the State of Oversight was received; alternatively, findings could be closed if a re-inspection confirms that the appropriate corrective action was taken. In the SAFA Centralised Database, a comment should be added to each open finding that despite several reminders (possibly including date and means) no response was required. Evidence of the communication could be uploaded as report attachments.

If the inspecting authority received confirmation that the operator does not exist anymore, findings could be closed whilst explaining this reason for closure in the justification.

6.2.2 Class 3 actions Depending on which class 3 of action has been taken when a cat 3 finding has been found, certain further follow-up actions may be deemed necessary to verify if the restrictions are respected or if corrective actions have been taken. Although it is preferred to perform such verification, this might not always be required (e.g. if the inspector has indications satisfying him/her that appropriate actions will be taken) or possible (e.g. for flight segments outside the EUROCONTROL area). It is up to the Member State to determine if verification is feasible and needs to be done. Especially for restrictions imposed during a ramp inspection, if the a posteriori verification shows that the airline did not respect them, this information should be mentioned in the final ramp inspection report or should be reported by means of a Standard Report (see §1.2).

 Class 3a (restrictions on the aircraft operation) Restrictions have been agreed/imposed. Verification of adherence to the restrictions might be considered. E.g. adherence to a restricted flight altitude may be checked by checking the ATC flight plans and/or the actual altitude flown as reported by the EUROCONTROL CFMU system. If some seats were to be blocked for their usage by passengers, this might be checked just before departure to confirm that the seats are not occupied;  Class 3b (Corrective actions before flight) A corrective action is required from the operator before the flight is commenced, therefore it should be possible to verify the corrective actions taken (e.g. if the tyre has been changed, if the recalculation of mass and balance has been done [correctly], etc.);  Class 3c (Aircraft grounded by inspecting NAA) At first, the inspecting state has to make sure that the aircraft will not depart as long as the reasons for the grounding remain.

Secondly, the grounding needs to be communicated immediately to the state of oversight and the operator home base. Any records of communication and other evidence should be gathered as evidential material.

Before lifting a grounding prompted by a deficiency which continues to affect the validity of the certificate of airworthiness for the aircraft, and for which an appropriate permit to flight has been issued, the inspecting State shall verify that the operator obtained the relevant permission from any State which will be overflown [art. 7.2 of Directive 2004/36/CE Grounding of aircraft].

Aircraft with a permit to fly from a competent authority of an EASA State of registry (if covered by Regulation (EC) No 216/2008, Commission Regulation (EC) No 1702/2003 and Commission Regulation (EC) No 2042/2003) do not need permission from EASA member States overflown.

SAFA Coordination Section Page 27 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material  Class 3d (Immediate operating ban) When class 3d action is imposed it is usually in addition to a Class 3a, 3b or 3c action.

Therefore, the further follow-up for the SAFA programme is considered to be covered by the follow-up of those actions. However, when class 3d action is taken, Member States should be mindful of their obligations under Regulation (EC) No 2111/2005.

6.3 Monthly report

Article 2.4 of the Commission Regulation (EC) No 768/2006 requires the Agency to:  advise the European Commission and the Member States on immediate actions or follow-up policy,  report potential safety problems, and  propose coordinated actions to the European Commission and the Member States when necessary on safety grounds and ensure co-ordination at the technical level of such actions.

For that reason, the Agency needs to be informed on follow-up actions taken by the Member States. Therefore, Member States are required by paragraph 6.4 of the Annex to Commission Directive 2008/49/EC to make available to the Agency a monthly report on the status of follow-up actions taken pursuant to ramp inspections.

In order to standardise the format of the data of such report, Member States are requested to use the template as shown in appendix 6.

As of version 2.0 of the centralised SAFA Database, the follow-up of inspections can be done electronically. Member States which make full use of these functionalities of the Database are considered to meet the requirement to send a monthly report since they provide all the information in “real time”.

6.3.1 Monthly report form instructions The report will contain an overview of all the correspondence related to follow-up actions, sent out or received by the Member States during the previous calendar month. The report shall be sent in a spreadsheet format (i.e. Microsoft® Excel) to the Agency (SAFA Coordination Section) by Email (safa@easa.europa.eu) within two weeks. The monthly reports should be sent aggregated (i.e. the monthly report for April will include also the reports for January, February and March).

With the introduction of the new database on 21 September 2011, the new follow-up functionality became available. When fully using this functionality, States are considered to meet the requirement to send the monthly report to EASA.

Once authorities and operators have registered to the database and are consequently using the follow-up feature, all required data will be stored by and can be retrieved from the database. However, since not all authorities and operators have obtained access we are still in a transition phase; nevertheless, information such as: a. date of notification b. means of notification c. follow-up information (by creating entries specifying/quoting the actions proposed/taken by the operator and/or its authority) can be entered manually in the Database instead of entering this into the monthly report.

At this stage, for all reports entered until 21 September 2011, as well as for replies to previously sent communications, you should either: • update the monthly report and continue to send it to us until all inspections have been closed; or SAFA Coordination Section Page 28 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material • transfer the above mentioned data on inspections with open findings to the database follow-up module which renders the monthly report obsolete.

Since providing the information “real time” via the SAFA Database is considered to meet the requirement to send a monthly report, there is no need to send any subsequent monthly report anymore as soon as the open inspections have been transferred to the database, or all inspections on the previous monthly report were closed. EASA should be informed as soon as you stop sending the monthly report for one of the above-mentioned reasons.

Explanatory comments to the form:  General o The electronic template will be made available to the Member States. By using the electronic version, the user is able to simply add new cells (e.g. when correspondence has been sent to both the State of operator and State of registry if different) to a row or add more rows to the form.

o Not the date of inspection, but the correspondence date determines in which monthly report the correspondence should be listed.

o Columns 2 and 4 are considered to be optional. For maximum efficiency and monitoring ability, Member States are encouraged to fill out the information in these columns as well.

Header and Footer:  State: the official name of the Member State;  NAA: the official name of the competent authority;  Month: the concerned calendar month including the calendar year.

OPERATOR SECTION Column (1) “Ramp inspection report number(s)”:  Every row should represent the information related to a certain ramp inspection.

Column (2) “Operator Code” (optional)  List the 3 letter ICAO operator code as in the SAFA database Column (3) “Operator Name”  List the operator’s name as in the SAFA database Column (4) “Findings” (optional)  List the findings raised in the respective report using the following format (x number of category 1 findings – y number of category 2 findings – z number of category 3 findings) (e.g. 3-1-2 = 3 category 1 findings; 1 category 2 finding and 2 category 3 findings) Column (5) “Written communication to operator (date)”  List the date when the written communication to the operator was sent (format: dd- mm-yyyy). Leave blank if no communication was sent because the operator/authority reacted already based on POI.

Column (6) “Receipt confirmed”  Indicate (Y/N) whether the receipt of the written communication is confirmed (this could be in the form of a fax receipt, e-mail read confirmation or a receipt confirmation in the case of registered mail).

Column (7) “Received on”  List the date when the operator reply was received (format: dd-mm-yyyy) Column (8) “Answer Satisfactory”  Indicate if the answer given by the operator is satisfactory (Y/N/P = Yes/No/Partially) Column (9) “Findings closed/Supplemental Communication”  Indicate, based on the reply of operator, whether the findings in the report have been closed I or if a supplemental communication was sent (S). Such supplemental communication should also be sent to the State of oversight. If a supplemental communication was sent, add an additional line filling-in the required fields (1, 5-17).

SAFA Coordination Section Page 29 of 217 © European Aviation Safety Agency, 2012 V 2.0 SAFA Ramp Inspections Guidance material STATE OF OVERSIGHT SECTION Column (10) “State of Oversight”  List the State (ICAO Code) ensuring oversight.

Note: If the State of Registry/Licensing is different than the State of Operator and written communication are sent to those States, add additional line(s) indicating all the concerned States using the following format: R-State of Registry L-State of Licensing Examples: State of Operator Brazil: SB State of registry Bermuda: R-TX State of Licensing United Kingdom: L-EG Column (11) “Written communication to NAA (date)”  List the date when the written communication to the NAA was sent (format: dd-mm- yyyy) Column (12) “Receipt confirmed”  Indicate (Y/N) whether the receipt of the written communication is confirmed (this could be in the form of a fax receipt, e-mail read confirmation or a receipt confirmation in the case of registered mail).

Column (13) “Reply requested”  Indicate (Y/N) whether it was requested from the State of oversight a “confirmation that they are satisfied with the corrective actions taken” as provided by article 6.4 (2) of the Annex to Commission Directive 2008/49/EC.

STATE OF OVERSIGHT REPLY Column (14) “Received on”  List the date when the NAA reply was received (format: dd-mm-yyyy); Column (15) “Answer Satisfactory”  Indicate if the answer given by the NAA is satisfactory (Y/N/P = Yes/No/Partially); Column (16) “Findings closed/Supplemental communication”  Indicate, based on the reply of the NAA, whether the findings in the report have been closed (C) or if a supplemental communication was sent (S). Such supplemental communication should also be sent to the operator. If a supplemental communication was sent add an additional line filling-in the required fields (1, 5-17).

Note: 1. If a reply (column 13) is not requested from the State of oversight then the fields 14-16 may be left empty. In this case, when the findings of a report are considered closed this should be reflected by entering ‘C’ in the column 9 only.

2. If a reply (column 13) is requested from the State of oversight the closure of the findings should be reflected by entering ‘C’ in both columns 9 and 16.

Column (17) “Additional Information”  Please indicate any additional information relevant to the follow-up of the inspection (e.g. operator reacted based on the POI, closure of findings confirmed/not confirmed by re-inspection).

SAFA Coordination Section Page 30 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspections

Guidance material

7 LIST OF APPENDICES

Appendix 1: List of Pre-described SAFA Findings (International Commercial Operations –Aeroplanes); Appendix 2: Instructions for the completion of the SAFA inspection report Appendix 3: Class of Actions matrix Appendix 4: Information leaflet templates Appendix 5: Follow-up written communication templates Appendix 6: Template for the monthly report on follow-up actions Appendix 7: SAFA National Coordinator tasks SAFA Coordination Section Page 31 of 217 © European Aviation Safety Agency, 2012 V 2.0 V 2.0 Page 32 of 217 Edition, Amendment 5, July 2011) th

Appendix 1

Edition, July 2006, Amendment 86) Edition, July 2011) th th Edition, July 2010, Amendment 35, October 2011) V (6 th Edition, July 2010, Amendment 36) Edition, July 2011, Amendment 10 incorporated) Edition, July 2011, Amendment 170) Edition, July 2005, Amendment 42, July 2009) Edition, July 2010, Amendment 103) I (9 th th Edition, July 2003 and Amendment 2 to the Supplement dated August 2007 incorporated) th th th th

Detailed inspection instructions including pre-described findings

7 (5

SAFA Ramp Inspection Procedures Guidance material

ICAO Annex 1 (11 ICAO Annex 2 (10 ICAO Annex 6, Part ICAO Annex ICAO Annex 8 (11 ICAO Annex 10, Volume ICAO Annex 15 (13 ICAO Annex 16, Volume I (6 ICAO Annex 18, (4 European (EUR) Regional Supplementary Procedures (ICAO Doc 7030) (5 ICAO Doc 9284, Technical Instructions for the Safe Transport of Dangerous Goods by Air, 2011-2012 Edition, Addendum No. 3/Corrigendum No. 2 A6-I-4.3.1 means Annex 6, Part I, Chapter 4.3.1 CC29 means Article 29 of the Chicago Convention EUR 2.1.6.2 means European (EUR) Regional Supplementary Procedures (ICAO Doc 7030), chapter 2.1.6.2 - - - - - - - - - - - SAFA Coordination Section © European Aviation Safety Agency, 2012 This document is using standard references contained in the following documents: The Convention on International Civil Aviation (also known as Chicago Convention), 9th Edition, 2006 Note: References to international standards are coded as in the following examples:

SAFA Ramp Inspection Procedures

Guidance material Insp. Item Insp. Item Description Page A Flight Deck A01 General Condition 34 A02 Emergency Exit 39 A03 Equipment 41 A04 Manuals 45 A05 Checklists 48 A06 Radio Navigation Charts 50 A07 Minimum Equipment List 53 A08 Certificate of Registration 57 A09 Noise certificate 59 A10 AOC or equivalent 61 A11 Radio license 64 A12 Certificate of Airworthiness 65 A13 Flight Preparation 67 A14 Weight and balance sheet 77 A15 Hand fire extinguishers 81 A16 Life jackets/flotation device 84 A17 Harness 86 A18 Oxygen equipment 87 A19 Flash light 90 A20 Flight crew license 91 A21 Journey log book 110 A22 Maintenance release 112 A23 Defect notification and rectification 113 A24 Preflight inspection 121 B Safety/Cabin B01 General Internal Condition 122 B02 Cabin Attendant’s Station/Crew Rest Area 127 B03 First Aid Kit/Emergency Medical Kit 130 B04 Hand fire extinguishers 133 B05 Life jackets/Flotation devices 135 B06 Seat belt and seat condition 138 B07 Emergency exit, lightning and marking, Torches 141 B08 Slides/Life Rafts, ELT 151 B09 Oxygen Supply 155 B10 Safety instructions 161 B11 Cabin crew members 166 B12 Access to emergency exits 168 B13 Safety of passenger baggage 174 B14 Seat capacity 175 C Aircraft Condition C01 General External Condition 176 C02 Doors and Hatches 179 C03 Flight Controls 180 C04 Wheels, tyres and brakes 181 C05 Undercarriage, skids/floats 182 C06 Wheel well 183 C07 Powerplant and Pylon 184 C08 Fan blades 185 C09 Propellers, rotors (main/tail) 186 C10 Obvious repairs 187 C11 Obvious unrepaired damage 188 C12 Leakage 189 D Cargo D01 General Condition of Cargo Compartment 190 D02 Dangerous Goods 193 D03 Safety of Cargo on Board 200 E General E01 General 202 SAFA Coordination Section © European Aviation Safety Agency, 2012 V 2.0 Page 34 of 217 some cases it can be proven (or at least reasonably assumed) that the manuals were not stored during flight since e.g. there is no suitable storage area. However, in those cases where it cannot be excluded that the crew indeed stores the manuals during flight, no finding should be raised. Such manuals and cases may have indeed been used by the crew during taxi and the turn-around before the inspector enters the flight deck.

Check general condition. Check the stowage of interior equipment, suitcases, navigation chart cases etc. Note: inspectors should make sure that manuals, flight cases etc. were indeed not appropriately stored during the incoming flight. In If a flight crew compartment door is installed, check the door locking/unlocking mechanism. On passenger carrying aeroplanes with MTOW > 45.500 kg (or with a passenger seating capacity more than 60 pax) check for installation and serviceability of the reinforced cockpit door. Check the means to monitor the door area from either pilots seat. Some means will fully satisfy the requirements, such as CCTV systems. However, means such as the spyhole do not enable the crew to monitor the door area from their seat and lead to a cat. 2 finding. The visual monitoring of the door area from the cockpit is of paramount importance, therefore alternative procedures such as an audio signalling code in addition to a spyhole are also considered to be not in compliance as they do not provide for an actual visual monitoring; therefore, a cat. 2 finding should be raised in such a situation as well. However, when this has been compensated during critical phases of the flight, for instance by the use of an additional crew member to monitor the area on behalf of the flight crew, or by denying access to the flight deck during these phases, it still constitutes a finding, but with a lesser impact on safety (hence the cat. 1 should be used). The presence in the cockpit of an additional crew member during all phases of the flight is considered to fully meet ICAO requirements. Check the condition of the flight deck windows (e.g. windshield cracks, possible delamination,…) Check if the crew composition meets the minimum crew requirements (available in the AFM) Check that no equipment is installed such that it obviously does not meet the systems design features and emergency landing provisions in Annex 8 Part IIIA/B, Chapter 4 (e.g. when equipment installed on the glare shield significantly impairs the pilots vision). Check the presence and serviceability of the windshield wipers (if required for the flight). Check if any electrical cables/wires are unintentionally exposed. Check the serviceability of the warning panel lights. When circumstances dictate (e.g. aircraft undergoes significant delay), check whether the crew members are in compliance with the flight and duty time rules contained within the Operations Manual.

Inspecting Instructions Inspections Item Title General Condition

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Part 1 Operations International Commercial Air Transport – Aeroplanes Inspection Item A01 V 2.0 Page 35 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Describe nature and extent of damage PDF code A01- 01 A01- 02 A01- 03 A01- 04 A01- 05 A01- 06 A01- 07 Pre-described Finding Door (un)locking mechanism at (Co)Pilot station N/A or U/S No means provided for crew notification Means to monitor the door area not available from either pilot’s station (but alternative operational procedures established for the critical phases of the flight) Means to monitor the door area not available from either pilot’s station (and no alternative operational procedures established) Means to monitor the door area not available or U/S (outside MEL limits) Cockpit door lock N/A or U/S (outside MEL limits) Damages to flight deck windows outside AMM limits Standard’s Text From 1 November 2003, all passenger-carrying aeroplanes of a maximum certificated take-off mass in excess of 45 500 kg or with a passenger seating capacity greater than 60 shall be equipped with an approved flight crew compartment door that is designed to resist penetration by small arms fire and grenade shrapnel, and to resist forcible intrusions by unauthorized persons. This door shall be capable of being locked and unlocked from either pilot's station. door, this door shall be capable of being locked, and means shall be provided by which cabin crew can discreetly notify the flight crew in the event of suspicious activity or security breaches in the cabin. In all aeroplanes which are equipped with a flight crew compartment door in accordance with 13.2.2: b) means shall be provided for monitoring from either pilot’s station the entire door area outside the flight crew compartment to identify persons requesting entry and to detect suspicious behaviour or potential threat. In all aeroplanes which are equipped with a flight crew compartment door in accordance with 13.2.2: b) means shall be provided for monitoring from either pilot’s station the entire door area outside the flight crew compartment to identify persons requesting entry and to detect suspicious behaviour or potential threat. In all aeroplanes which are equipped with a flight crew compartment door in accordance with 13.2.2: b) means shall be provided for monitoring from either pilot’s station the entire door area outside the flight crew compartment to identify persons requesting entry and to detect suspicious behaviour or potential threat. door, this door shall be capable of being locked, and means shall be provided by which cabin crew can discreetly notify the flight crew in the event of suspicious activity or security breaches in the cabin.

In all aeroplanes which are equipped with a flight crew compartment In all aeroplanes which are equipped with a flight crew compartment Std. ref. A6-I-13.2.2 A6-I-13.2.1 A6-I-13.2.3 A6-I-13.2.3 A6-I-13.2.3 A6-I-13.2.1 Cat. 1 2 3 3 1 2 3 Std. I I I I I I M

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A01 A01 A01 A01 A01 A01 A01 V 2.0 Page 36 of 217 Instructions for completing the detailed description Describe the observed situation vs. the requirements in the OPS Manual Describe the observed situation vs. the requirements in the OPS Manual Indicate what interior equipment/object( s) was not secured Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A01- 08 A01- 09 A01- 10 A01- 11 A01- 12 A01- 13 Pre-described Finding Insufficient number of flight crew members Flight Crew member not in compliance with the flight and duty time rules Interior equipment and/or other object(s) not correctly secured or stowed during flight Reinforced cockpit door not installed (on passenger flights) Lights U/s in warning panel (outside MEL limits) Cockpit installations significantly decreasing pilots vision Standard’s Text The number and composition of the flight crew shall not be less than that specified in the operations manual. The flight crews shall include flight crew members in addition to the minimum numbers specified in the flight manual or other documents associated with the certificate of airworthiness, when necessitated by considerations related to the type of aeroplane used, the type of operation involved and the duration of flight between points where flight crews are changed. An operator shall formulate rules to limit flight time and flight duty periods and for the provision of adequate rest periods for all its crew members. These rules shall be in accordance with the regulations established by the State of the Operator, or approved by that State, and included in the operations manual. Provisions shall be made in the design of the aeroplane to protect the occupants, in the event of an emergency landing, from fire and from the direct effects of deceleration forces as well as from injuries arising from the effect of deceleration forces on the aeroplane’s interior equipment. Crew environment. The design of the flight crew compartment shall be such as to minimize the possibility of incorrect or restricted operation of the controls by the crew, due to fatigue, confusion or interference From 1 November 2003, all passenger-carrying aeroplanes of a maximum certificated take-off mass in excess of 45 500 kg or with a passenger seating capacity greater than 60 shall be equipped with an approved flight crew compartment door that is designed to resist penetration by small arms fire and grenade shrapnel, and to resist forcible intrusions by unauthorized persons. This door shall be capable of being locked and unlocked from either pilot’s station. Pilot vision. The arrangement of the pilot compartment shall be such as to afford a sufficiently extensive, clear and undistorted field of vision for the safe operation of the aeroplane, and to prevent glare and reflections that would interfere with the pilot’s vision. The design Std. ref. A6-I-9.1.1 A6-I-2.2.10.2 A8-IIIA- 4.1.7.1 A8-IIIB-4.6.1 A8-IIIA- 4.1.6.(c) A8-IIIB- 4.2.(c) A6-I-13.2.2 A8-IIIA- 4.1.6d, A8-IIIB-4.2d Cat. 3 3 3 2 3 3 Std. I I I I M I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A01 A01 A01 A01 A01 A01 V 2.0 Page 37 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A01- 14 A01- 15 A01- 16 Pre-described Finding Windshield wipers/cleaning/drying system not installed or inoperative and their usage required due to precipitation (outside MEL limits) Equipment installations obviously not in compliance with Annex 8, Part IIIA/B, Chapter 4 Operational flight deck markings and/or placards missing or incorrect Standard’s Text features of the pilot windshield shall permit, under precipitation conditions, sufficient vision for the normal conduct of flight and for the execution of approaches and landings. Pilot vision. The arrangement of the pilot compartment shall be such as to afford a sufficiently extensive, clear and undistorted field of vision for the safe operation of the aeroplane, and to prevent glare and reflections that would interfere with the pilot’s vision. The design features of the pilot windshield shall permit, under precipitation conditions, sufficient vision for the normal conduct of flight and for the execution of approaches and landings. Under all anticipated operating conditions, the aeroplane shall not possess any feature or characteristic that renders it unsafe. Compliance with the appropriate airworthiness requirements shall be based on evidence either from tests, calculations, or calculations based on tests, provided that in each case the accuracy achieved will ensure a level of airworthiness equal to that which would be achieved were direct tests conducted. The tests of 1.5.1 shall be such as to provide reasonable assurance that the aeroplane, its components and equipment are reliable and function correctly under the anticipated operating conditions. The operating limitations within which compliance with the Standards of this Annex is determined, together with any other information necessary to the safe operation of the aeroplane, shall be made available by means of an aeroplane flight manual, markings and placards, and such other means as may effectively accomplish the purpose. The limitations and information shall include at least those prescribed in 9.2, 9.3 and 9.4. The operating limitations within which compliance with the Standards of this Annex is determined, together with any other information necessary to the safe operation of the aeroplane, shall be made available by means of a flight manual, markings and placards, and such other means as may effectively accomplish the purpose. The limitations and information shall include at least those prescribed in this sub-part.

Std. ref. A8-IIIA- 4.1.6d, A8-IIIA-1.4, A8-IIIB-1.3 A8-IIIA-1.5, A8-IIIB-1.4 A8-IIIA-9.1 A8-IIIB-7.1 Cat. 3 3 Std. I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A01 A01 A01 V 2.0 Page 38 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A01- 17 A01- 18 Pre-described Finding Inadvertently exposed electrical cables/wires in the cockpit Windshield delamination outside AMM limits Standard’s Text Unsafe features and characteristics Under all anticipated operating conditions, the aeroplane shall not possess any feature or characteristic that renders it unsafe.

Std. ref. A8-IIIA-1.4 A8-IIIB-1.3 Cat. 2 3 Std. I M

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A01 A01 V 2.0 flight Page 39 of 217 during Instructions for completing the detailed description Indicate why the access to emergency exit is impeded condition PDF code A02- 01 A02- 02 unsecured an in temporarily Pre-described Finding Access to emergency exit impeded Emergency exits U/S placed be may equipment/luggage that aware be should Inspectors preparation. In such cases the inspectors should seek confirmation that the equipment/luggage will be securely stowed before flight. If the crew is unable to confirm this, a finding may be appropriate.

Inspecting Instructions Check serviceability of exits and, when ropes are installed, check that they are secured. Check whether access to emergency exits is restricted or impeded. Note: Standard’s Text The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits, shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane and shall be shown to be suitable for their intended purpose. On aeroplanes certificated for ditching conditions, provisions shall be made in the design to give maximum practicable assurance that safe evacuation from the aeroplane of passengers and crew can be executed in case of ditching. Safety and survival equipment. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. Safety and survival equipment. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of Std. ref. A8-IIIA-4.1.7.3 A8-IIIA-4.1.7.2 A8-IIIA-8.3 A8-IIIB-4.6.2 A8-IIIB-4.6.4 A8-IIIB-6.3 A8-V-6.3 Cat. 3 3

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Emergency Exit Std. I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A02 Inspection Item A02 A02 V 2.0 Page 40 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed (e.g. what emergency facilities are not available or unserviceable) PDF code A02- 03 Pre-described Finding If applicable, flight deck escape facilities (ropes, hatches, harnesses) not available or unserviceable (outside MEL) Standard’s Text operation shall be plainly marked. Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane and shall be shown to be suitable for their intended purpose. On aeroplanes certificated for ditching conditions, provisions shall be made in the design to give maximum practicable assurance that safe evacuation from the aeroplane of passengers and crew can be executed in case of ditching. Safety and survival equipment. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. Safety and survival equipment. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked.

Std. ref. A8-IIIA-4.1.7.2 A8-IIIA-8.3 A8-IIIB-4.6.2 A8-IIIB-4.6.4 A8-IIIB-6.3 A8-V-6.3 Cat. 3

SAFA Ramp Inspection Procedures Guidance material

Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A02 V 2.0 Page 41 of 217 finding. requirements regarding the E-GPWS. Only the 7-channel (SRPBZ) with forward looking terrain avoidance function meets the ICAO requirements. finding. finding.

Inspecting Instructions All Flights: a) TAWS (E-GPWS) Check if installed and serviceable. If unserviceable check if properly deferred (reported in the ATLB) and check if still within MEL dispatch limits. Verify that the installed GPWS has a forward looking terrain avoidance function. If the terrain database is found to be expired, verify against the MEL the dispatch conditions. When an operational test can be performed by the pilot, it should be requested Note: On certain aircraft such a test cannot be performed by the pilots but only by maintenance personnel: this does not constitute a Note: some CIS-built aircraft are equipped with GPWS systems like the SSOS or SPPZ (SPBZ) that do not fulfil the ICAO In the case where an aircraft is found not to have TAWS (E-GPWS) installed then the competent authority should consider imposing an immediate operating ban on that aircraft. The aircraft should be allowed to depart only on a non-revenue flight. b) ACAS II (TCAS) Check if installed and serviceable. If unserviceable check if properly deferred (reported in the ATLB) and check if still within MEL dispatch limits. When an operational test can be performed by the pilot, it should be requested. Note: On certain aircraft such a test cannot be performed by the pilots but only by maintenance personnel: this does not constitute a In the case where an aircraft is found not to be fitted with a compliant TCAS/ACAS II system then the competent authority should consider imposing an immediate operating ban on that aircraft. The aircraft should be allowed to depart only on a non-revenue flight. For aircraft with their first CoA issued on or after 1 March 2012, check if ACAS II, software version 7.1 is installed. This can be done by performing a test of aural warnings; version 7.1 will have the extra resolution advisory “Level off, level off” (this requirement is only applicable in the territory of the EU Member States, Iceland, Norway and Switzerland). c) Cockpit Voice Recorder When an operational test can be performed by the pilot, it should be requested. Note: On certain aircraft such a test cannot be performed by the pilots but only by maintenance personnel: this does not constitute a Flights in designated airspace: a) RVSM Check whether the equipment unserviceability (if any) renders the aircraft non-RVSM capable (check with Doc 9614). Area of applicability (ICAO Doc 7030):

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Equipment SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A03 V 2.0 Kharkiv, Page 42 of 217 Kaliningrad, Instructions for completing the detailed description Indicate the particulars of the situation PDF code A03- 01 Istanbul, Hannover, Frankfurt, France, Pre-described Finding Required equipment installed but clearly not being used during operation by crew Düsseldorf, Chisinau, Budapest, Bucuresti, Bruxelles, Brindisi, used, e.g. if an equipment is found to be covered and therefore rendered unusable, this should result in a cat. 3 finding. If equipment is found to be obstructed (e.g. by a manual) during flight preparation phase, this should not lead to a finding.

2.1.1 RVSM shall be applicable in that volume of airspace between FL 290 and FL 410 inclusive in the following flight information regions/upper flight information regions (FIRs/UIRs): Amsterdam, Ankara, Athinai, Barcelona, Beograd, Berlin, Bodo, Bratislava, Bremen, Brest, KØbenhavn, Kyiv, Lisboa, Ljubljana, London, L‘viv, Madrid, Malmö, Malta, Milano, Minsk, München, Nicosia, Odesa, Oslo, Praha, Rhein, Riga, Roma, Rovaniemi, Sarajevo, Scottish, Shannon, Simferopol, Skopje, Sofia, Stavanger, Stockholm, Sundsvall, Switzerland, Tallinn, Tampere, Tirana, Trondheim, Varna, Vilnius, Warszawa, Wien, Zagreb. 2.1.2 RVSM shall be applicable in either all, or part of, that volume of airspace between FL 290 and FL 410 inclusive in the following FIRs/UIRs: Canaries (AFI Region), Casablanca, Tunis. b) RNAV Check that the aircraft is equipped with RNAV equipment. For operations in airspace designated as B-RNAV or P-RNAV check if the aircraft meets the Required Navigation Performance (RNP) requirements. c) MNPS Check whether the equipment unserviceability (if any) renders the aircraft non-MNPS capable. Area of applicability (ICAO Doc 7030): The MNPS shall be applicable in that volume of airspace between FL 285 and FL 420 within the Oceanic Control Areas of Santa Maria, Shanwick, Reykjavik, Gander Oceanic and New York, excluding the area west of 60°W and south of 38°30'N. d) 8.33 kHz channel spacing Check that radio equipment is 8.33 kHz channel spacing capable. This can be checked by requesting to select an 8.33 kHz channel, for example, 132.055 kHz on the radio control panel. The panel should normally show 6 digits – however some radio control panels may omit the leading “1” and display only 5 digits, e.g. 32.055. Area of applicability: The carriage of 8.33 kHz channel spacing capable radio equipment is mandatory for operations in the specified ICAO EUR region for flights above FL 195. Note: Inspectors, while checking this inspection item, should also assess whether the required equipment is obviously not being Standard’s Text In addition to the minimum equipment necessary for the issuance of a certificate of airworthiness, the instruments, equipment and flight documents prescribed in the following paragraphs shall be installed or carried, as appropriate, in aeroplanes according to the aeroplane used and to the circumstances under which the flight is to be conducted. The prescribed instruments and equipment, including their installation, shall be approved or accepted by the State of Std. ref. A6-I-6.1.1 Cat. 3

SAFA Ramp Inspection Procedures Guidance material

Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A03 V 2.0 Page 43 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate if no system at all was found or if the forward looking function is missing. If unserviceable, specify the reason.

PDF code A03- 02 A03- 03 A03- 04 A03- Pre-described Finding ACAS II N/A or U/S (outside MEL limits) Aircraft with first CoA issued on or after 1 March 2012 not equipped with ACAS II, software version 7.1 GPWS with forward looking terrain avoidance function not installed or unserviceable (outside MEL limits) Radio channel spacing does 1) gear not locked down; 2) flaps not in a landing position; and Standard’s Text Registry From 1 January 2005, all turbine-engined aeroplanes of a maximum certificated take-off mass in excess of 5 700 kg or authorized to carry more than 19 passengers shall be equipped with an airborne collision avoidance system (ACAS II). 2.3.1 Responsibility of pilot-in-command The pilot-in-command of an aircraft shall, whether manipulating the controls or not, be responsible for the operation of the aircraft in accordance with the rules of the air, except that the pilot-in-command may depart from these rules in circumstances that render such departure absolutely necessary in the interests of safety. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in command is satisfied that: b) the instruments and equipment prescribed in Chapter 6, for the particular type of operation to be undertaken, are installed and are sufficient for the flight. From 1 January 2007, all turbine-engined aeroplanes of a maximum certificated take-off mass in excess of 5 700 kg or authorized to carry more than nine passengers shall be equipped with a ground proximity warning system which has a forward looking terrain avoidance function. From 1 January 2007, all piston-engined aeroplanes of a maximum certificated take-off mass in excess of 5 700 kg or authorized to carry more than nine passengers shall be equipped with a ground proximity warning system which provides the warnings in 6.15.8 a) and c), warning of unsafe terrain clearance and a forward looking terrain avoidance function. A ground proximity warning system shall provide, unless otherwise specified herein, warnings of the following circumstances: a) excessive descent rate; b) excessive terrain closure rate; c) excessive altitude loss after take-off or go-around; d) unsafe terrain clearance while not in landing configuration: e) excessive descent below the instrument glide path. All aircraft operating above FL 195 in the European Region shall be Std. ref. A6-I-6.18.2 A2-2.3.1 A6-I-4.3.1 A6-I-6.15.4 A6-I-6.15.6 A6-I-6.15.8 EUR 3.2.1 Cat. 3 2 3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A03 A03 A03 A03 V 2.0 Page 44 of 217 Instructions for completing the detailed description Indicate what equipment was N/A or U/S and type of operation PDF code 05 A03- 06 A03- 07 Pre-described Finding not meet the airspace requirements for the filed flight plan Required navigation equipment N/A or U/S (outside MEL limits) Cockpit Voice Recorder inoperative (outside MEL limits) Standard’s Text equipped with 8.33 kHz channel spacing capable radio equipment. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in command is satisfied that: b) the instruments and equipment prescribed in Chapter 6, for the particular type of operation to be undertaken, are installed and are sufficient for the flight; An aeroplane shall be provided with navigation equipment which will enable it to proceed: a) in accordance with the flight plan; and b) in accordance with the requirements of air traffic services; except when, if not so precluded by the appropriate authority, navigation for flights under the visual flight rules is accomplished by visual reference to landmarks. All aeroplanes of a maximum certificated take-off mass of over 5 700 kg for which the individual certificate of airworthiness is first issued on or after 1 January 2003, shall be equipped with a CVR capable of retaining the information recorded during at least the last two hours of its operation. All aeroplanes of a maximum certificated take-off mass of over 5 700 kg for which the individual certificate of airworthiness is first issued on or after 1 January 1987 shall be equipped with a CVR. All turbine-engined aeroplanes, for which the individual certificate of airworthiness was first issued before1 January 1987, with a maximum certificated take-off mass of over 27 000 kg that are of types of which the prototype was certificated by the appropriate national authority after 30 September 1969 shall be equipped with a CVR.

Std. ref. A6-I-4.3.1 A6-I-7.2.1 A6-I-6.3.2.1.3 A6-I-6.3.2.1.4 A6-I-6.3.2.1.5 Cat. 3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A03 A03 V 2.0 Page 45 of 217 Instructions for completing the detailed description Indicate what information is missing PDF code A04-01 Pre-described Finding No or incomplete parts of the Operations Manual pertaining to flight operations on board presence of instructions and data for mass and balance control. the list of the navigational equipment to be carried including any requirements relating to operations where performance- based navigation is prescribed. Presence of data that enables the crew to carry out performance calculations Information on fuel planning Flight and duty time requirements Safety precautions during refuelling with passengers on board. Instructions on the carriage of dangerous goods (with DG on board)” flight operations. unless it is obvious that the pilot(s) do not understand the language in which the manuals are written. is not understood by any of the flight crew members. This is reflected in the respective cat 2 and cat 3 pre-described findings. does not require that proof of such approval be contained in the manual itself. It is up to each and every Contracting State to determine how they approve a manual and whether evidence of such approval is required in the manual. The absence of a specific approval does not constitute a finding.

- - - - - - - Inspecting Instructions Check for presence of Operations Manual and Aircraft Flight Manual. (Note: flight manual data may be included in the operations manual). Check if their content complies with the requirements and is up to date (e.g. with the latest revision of the AFM). Note: Not all parts of the OPS Manual have to be carried on board. As a minimum there shall be available those parts pertaining to Note: in the Ops. manual the following subjects, in particular, could be checked: Check if the flight crew is able to understand the language in which the OPS Manual and/or AFM are written. Note: ICAO standards do not require the manuals to be written in English language. Such a case does not constitute a finding Note: the impact on safety is different in case only one flight crew member is not able to understand the language of the OM, or if it Note: Annex 6 does require that specific parts of the Operations Manual be approved by the National Authority. However, the Annex Standard’s Text An aeroplane shall carry: a) the operations manual prescribed in 4.2.3, or those parts of it that pertain to flight operations; b) the flight manual for the aeroplane, or other documents containing performance data required for the application of Chapter 5 and any other information necessary for the operation Std. ref. A6-I-6.2.3ab Cat.

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Manuals Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A04 Inspection Item A04 V 2.0 Page 46 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate what performance or limitations data is missing Indicate the particulars of the situation observed PDF code A04-02 A04-03 A04-04 A04-05 A04-06 A04-07 Pre-described Finding No rules on flight time, flight duty and rest time limitations in the Operations manual Operations manual not up to date Operations manual not issued by the operator Operations Manual published in a language not understood by a member of the flight crew No or incomplete performance and limitations data on board No information and instructions in Operations Manual on the actions to be taken in the event of an emergency (DG on board) Standard’s Text of the aeroplane within the terms of its certificate of airworthiness, unless these data are available in the operations manual; An operator shall formulate rules to limit flight time and flight duty periods and for the provision of adequate rest periods for all its crew members. These rules shall be in accordance with the regulations established by the State of the Operator, or approved by that State, and included in the operations manual. An operator shall provide, for the use and guidance of operations personnel concerned, an operations manual in accordance with Appendix 2. The operations manual shall be amended or revised as is necessary to ensure that the information contained therein is kept up to date. All such amendments or revisions shall be issued to all personnel that are required to use this manual. An operator shall provide, for the use and guidance of operations personnel concerned, an operations manual in accordance with Appendix 2. The operations manual shall be amended or revised as is necessary to ensure that the information contained therein is kept up to date. All such amendments or revisions shall be issued to all personnel that are required to use this manual. An operator shall provide, for the use and guidance of operations personnel concerned, an operations manual in accordance with Appendix 2. The operations manual shall be amended or revised as is necessary to ensure that the information contained therein is kept up to date. All such amendments or revisions shall be issued to all personnel that are required to use this manual. An aeroplane shall carry: a) the operations manual prescribed in 4.2.3, or those parts of it that pertain to flight operations; b) the flight manual for the aeroplane, or other documents containing performance data required for the application of Chapter 5 and any other information necessary for the operation of the aeroplane within the terms of its certificate of airworthiness, unless these data are available in the operations manual; The operator shall provide such information in the Operations Manual as will enable the flight crew to carry out its responsibilities with regard to the transport of dangerous goods and shall provide instructions as to the action to be taken in the event of emergencies arising involving dangerous goods.

Std. ref. A6-I-2.2.10.2 A6-I-4.2.3.1 A6-I-4.2.3.1 A6-I-4.2.3.1 A6-I-6.2.3ab A18-9.2 Cat. 2 2 2 2 3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I I I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A04 A04 A04 A04 A04 A04 V 2.0 Page 47 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code A04-08 Pre-described Finding Operations Manual published in a language not understood by any of the flight crew members Standard’s Text An operator shall provide, for the use and guidance of operations personnel concerned, an operations manual in accordance with Appendix 2. The operations manual shall be amended or revised as is necessary to ensure that the information contained therein is kept up to date. All such amendments or revisions shall be issued to all personnel that are required to use this manual.

Std. ref. A6-I-4.2.3.1 Cat. 3

SAFA Ramp Inspection Procedures Guidance material

Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A04 V 2.0 Page 48 of 217 Instructions for completing the detailed description Indicate what details do not conform Indicate the particulars of the situation observed PDF code A05- 01 A05- 02 A05- 03 Pre-described Finding Checklists do not conform with the checklist details in the operations manual No checklist details in the operations manual Normal and emergency checklists not readily accessible to all relevant flight crew members provided that the crew can demonstrate access to such checklists and they are correctly documented in the Operations manual. inspectors may find separate checklists for each phase of the flight, which is fully compliant. checklist only.

Inspecting Instructions Note: Most modern aircraft have some checklists held electronically, e.g. the Airbus ECAM system. This should not constitute a finding Check if the OPS Manual contains the required checklists. Compare the version in OPS Manual with the ones available to the crew. Check if their content is in compliance with the operating manual covering all flight phases, in normal and emergency operations. Note: Normal, non-normal and emergency checklists are sometimes combined in a “Quick Reference Handbook”. Nevertheless, Check if the checklists are identical for all members of the flight crew. Note: If checklists with a different number of revision/different dates are present, check if the content is identical. Note: On some ex-Soviet built aircraft only the flight engineer has a checklist. The pilot and co-pilot may be working from a memorised Standard’s Text aircraft operating manual, for each aircraft type operated, containing the normal, abnormal and emergency procedures relating to the operation of the aircraft. The manual shall include details of the aircraft systems and of the checklists to be used. The design of the manual shall observe Human Factors principles. Note: - Guidance material on the application of Human Factors principles can be found in the Human Factors Training Manual (Doc 9683). aircraft operating manual, for each aircraft type operated, containing the normal, abnormal and emergency procedures relating to the operation of the aircraft. The manual shall include details of the aircraft systems and of the checklists to be used. The design of the manual shall observe Human Factors principles. Note: - Guidance material on the application of Human Factors principles can be found in the Human Factors Training Manual (Doc 9683). crews prior to, during and after all phases of operations, and in emergency, to ensure compliance with the operating procedures contained in the aircraft operating manual and the aeroplane flight manual or other documents associated with the certificate of Check if checklists are available and easily accessible. The operator shall provide operations staff and flight crew with an The operator shall provide operations staff and flight crew with an The checklists provided in accordance with 6.1.4 shall be used by flight Std. ref. A6-I-6.1.4 A6-I-6.1.4 A6-I-4.2.6 Cat. 2 2 2

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Checklists Std. I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A05 Inspection Item A05 A05 A05 V 2.0 Page 49 of 217 Instructions for completing the detailed description Indicate the flight phases are not covered Indicate the particulars of the situation observed PDF code A05- 04 A05- 05 A05- 06 Pre-described Finding Checklists not covering all flight phases Different versions of checklists used by captain and co-pilot No normal and emergency checklists available Standard’s Text airworthiness and otherwise in the operations manual, are followed … The checklists provided in accordance with 6.1.4 shall be used by flight crews prior to, during and after all phases of operations, and in emergency, to ensure compliance with the operating procedures contained in the aircraft operating manual and the aeroplane flight manual or other documents associated with the certificate of airworthiness and otherwise in the operations manual, are followed. The design and utilization of checklists shall observe Human Factors principles. crews prior to, during and after all phases of operations, and in emergency, to ensure compliance with the operating procedures contained in the aircraft operating manual and the aeroplane flight manual or other documents associated with the certificate of airworthiness and otherwise in the operations manual, are followed ... crews prior to, during and after all phases of operations, and in emergency, to ensure compliance with the operating procedures contained in the aircraft operating manual and the aeroplane flight manual or other documents associated with the certificate of airworthiness and otherwise in the operations manual, are followed … The checklists provided in accordance with 6.1.4 shall be used by flight The checklists provided in accordance with 6.1.4 shall be used by flight Std. ref. A6-I-4.2.6 A6-I-4.2.6 A6-I-4.2.6 Cat. 2 3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A05 A05 A05 V 2.0 Page 50 of 217 Instructions for completing the detailed description Indicate the expiration date of the database Indicate the expiration date of the database PDF code A06- 01 A06- 02 Pre-described Finding Navigation database out of date (within MEL limits) Navigation database out of date (outside MEL limits) to be flown, including associated diversions, are up to date to the latest AIRAC amendments. as a General Remark.

Inspecting Instructions Check if the required departure, en-route, approach and aerodrome charts are available, within reach, up-to-date to the latest AIRAC amendments (including those for the alternate aerodromes). Note: one or two amendments missing in the chart library could still be acceptable provided the charts to cover the route flown, or about Note: If other charts are not updated, but the required ones are, this does not constitute a finding. Such a case should be reported though Check the validity of the FMS/GPS database; in case of expiration, check the MEL. Standard’s Text An operator shall implement procedures that ensure the timely distribution and insertion of current and unaltered electronic navigation data to all aircraft that require it. Information concerning the circumstances listed in Appendix 4, Part 1, shall be distributed under the regulated system (AIRAC), i.e. basing establishment, withdrawal or significant changes upon a series of common effective dates at intervals of 28 days, including 14 January 2010. The information notified therein shall not be changed further for at least another 28 days after the effective date, unless the circumstance notified is of a temporary nature and would not persist for the full period. An operator shall implement procedures that ensure the timely distribution and insertion of current and unaltered electronic navigation data to all aircraft that require it. Information concerning the circumstances listed in Appendix 4, Part 1, shall be distributed under the regulated system (AIRAC), i.e. basing establishment, withdrawal or significant changes upon a series of common effective dates at intervals of 28 days, including 14 January 2010. The information notified therein shall not be changed further for at least another 28 days after the effective date, unless the circumstance notified is of a temporary nature and would not persist for the full period.

Std. ref. A6-I-7.4.2 A15-6.1.1 A6-I-7.4.2 A15-6.1.1 Cat. 2 3

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Radio Navigation Charts Std. I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A06 Inspection Item A06 A06 V 2.0 Page 51 of 217 what charts are not up to date the date/number of revision of the inspected charts the date/number of revision of the current applicable charts what charts are not up to date the expiration date of the database what charts are not up to date the date/number of revision of the inspected charts the date/number of Indicate: Instructions for completing the detailed description Indicate:      Indicate what charts are missing Indicate:    PDF code A06- 03 A06- 04 A06- 05 A06- 06 Pre-described Finding Required en-route charts out of date (navigation database up to date) Required en-route charts and navigation database out of date Required instrument charts not on board Required instrument charts (except en-route) out of date c) current and suitable charts to cover the route of the proposed flight c) current and suitable charts to cover the route of the proposed flight c) current and suitable charts to cover the route of the proposed flight c) current and suitable charts to cover the route of the proposed flight Standard’s Text and any route along which it is reasonable to expect that the flight may be diverted. Information concerning the circumstances listed in Appendix 4, Part 1, shall be distributed under the regulated system (AIRAC), i.e. basing establishment, withdrawal or significant changes upon a series of common effective dates at intervals of 28 days, including 14 January 2010. The information notified therein shall not be changed further for at least another 28 days after the effective date, unless the circumstance notified is of a temporary nature and would not persist for the full period. An aeroplane shall carry: and any route along which it is reasonable to expect that the flight may be diverted. An operator shall implement procedures that ensure the timely distribution and insertion of current and unaltered electronic navigation data to all aircraft that require it and any route along which it is reasonable to expect that the flight may be diverted. Information concerning the circumstances listed in Appendix 4, Part 1, shall be distributed under the regulated system (AIRAC), i.e. basing establishment, withdrawal or significant changes upon a series of common effective dates at intervals of 28 days, including 14 January 2010. The information notified therein shall not be changed further for at least another 28 days after the effective date, unless the circumstance notified is of a temporary nature and would not persist for the full period. and any route along which it is reasonable to expect that the flight may be diverted. Information concerning the circumstances listed in Appendix 4, Part 1, shall be distributed under the regulated system (AIRAC), i.e. basing establishment, withdrawal or significant changes upon a series of common effective dates at intervals of 28 days, including 14 January An aeroplane shall carry: An aeroplane shall carry: An aeroplane shall carry: Std. ref. A6-I-6.2.3c A15-6.1.1 A6-I-6.2.3c A6-I-7.4.2 A6-I-6.2.3c A15-6.1.1 A6-I-6.2.3c A15-6.1.1 Cat. 2 3 3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A06 A06 A06 A06 V 2.0 Page 52 of 217 revision of the current applicable charts what charts are not up to date the date/number of revision of the inspected out of date charts Instructions for completing the detailed description Indicate:   PDF code A06- 07 Pre-described Finding Several sets of required instrument charts available in the flight deck, of which one (not in use)is out of date c) current and suitable charts to cover the route of the proposed flight Standard’s Text 2010. The information notified therein shall not be changed further for at least another 28 days after the effective date, unless the circumstance notified is of a temporary nature and would not persist for the full period. An aeroplane shall carry: and any route along which it is reasonable to expect that the flight may be diverted. Information concerning the circumstances listed in Appendix 4, Part 1, shall be distributed under the regulated system (AIRAC), i.e. basing establishment, withdrawal or significant changes upon a series of common effective dates at intervals of 28 days, including 14 January 2010. The information notified therein shall not be changed further for at least another 28 days after the effective date, unless the circumstance notified is of a temporary nature and would not persist for the full period.

Std. ref. A6-I-6.2.3c A15-6.1.1 Cat. 2

SAFA Ramp Inspection Procedures Guidance material

Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A06 V 2.0 Page 53 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed ATA 23 Communication PDF code A07- 01 Pre-described Finding MEL does not reflect aircraft configuration or the operations specifications ) but should mention the actual required number.

an acceptable alternative. might not have to be updated. A missing revision number is no reason to raise a finding; the document control process is to be agreed by the overseeing authority. If it is found that a MEL is not up to date resulting in a less restrictive document, questions may be raised in the follow-up phase on the appropriate document control. at least 4 months (since publication of the revised MMEL) for the revision of a MEL. configuration control. approval be contained in the MEL itself or has to be carried on board. It is up to each and every Contracting State to determine how they approve a manual and whether evidence of such approval is required in the manual. The absence of a specific approval of the MEL on board of the aircraft does not constitute a finding.

Inspecting Instructions Check if the MEL is available. Note: An increasing number of operators do not have the MEL on board, but available via a data downlink. This should be considered as Check if the MEL is not less restrictive than MMEL. Note: If it is found that the MEL does not incorporate the latest revision of the MMEL, this should be reported as a General Remark (cat. G). Note: Checking the revision status of the MEL might not be enough; in case the last revision introduced less restrictive conditions, the MEL Note: It takes time before more strict requirements introduced by a new MMEL will be implemented. Inspectors should allow a timeframe of Check if MEL content reflects actual equipment installed on the aircraft and takes into account the special approvals in the operations specifications. Check if the MEL contains the (M) maintenance and/or (O) operational procedures. Check if the MEL is fully customised. For example, the MEL should not contain a reference to regulatory material (“ systems – Any in excess of those required by 14 CFR may be inoperative provided it is not powered by Standby Bus and is not required for emergency procedures.” Note: Mainly for passenger cabin related items, the number may be missing, provided that the MEL reflects an alternate means of Check if the deferred defects (if any) are in accordance with the MEL instructions. Note: Annex 6 does require that the MEL is approved by the State of Operator. However, the Annex 6 does not require that proof of such Standard’s Text The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator Std. ref. A6-I-6.1.3 Cat. 2

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Minimum Equipment List Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A07 Inspection Item A07 V 2.0 Page 54 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A07- 02 A07- 03 A07- 04 A07- 05 (O) and/or requiring such (M) lacking Pre-described Finding MEL lacking (M) and/or (O) procedures when required (no deferred defect requiring such procedure) MEL procedures when required (with deferred defect procedure) MEL less restrictive than the MMEL (with deferred defects affected by the lower restrictions) MEL less restrictive than the MMEL (without deferred defects affected by the lower restrictions) Standard’s Text shall ensure that the MEL does not affect the aeroplane's compliance with the airworthiness requirements applicable in the State of Registry. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the airworthiness requirements applicable in the State of Registry. Note: - Attachment F contains guidance on the minimum equipment list. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the airworthiness requirements applicable in the State of Registry. Note: - Attachment F contains guidance on the minimum equipment list. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the airworthiness requirements applicable in the State of Registry. Note: - Attachment F contains guidance on the minimum equipment list. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the airworthiness requirements applicable in the State of Registry. Note: - Attachment F contains guidance on the minimum equipment list.

Std. ref. A6-I-6.1.3 A6-I-6.1.3 A6-I-6.1.3 A6-I-6.1.3 Cat. 2 3 3 2

SAFA Ramp Inspection Procedures Guidance material

Std. I I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A07 A07 A07 A07 V 2.0 Page 55 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A07- 06 A07- 07 A07- 08 A07- 09 A07- 10 Pre-described Finding MEL not available (no deferred defects) Some MEL items not fully customised (but no defects affecting those items) MMEL instead of MEL Some MEL items not fully customised (with defects affecting those items) MEL not available (with deferred defects) Standard’s Text The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the airworthiness requirements applicable in the State of Registry. Note: - Attachment F contains guidance on the minimum equipment list. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the airworthiness requirements applicable in the State of Registry. Note: - Attachment F contains guidance on the minimum equipment list. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the airworthiness requirements applicable in the State of Registry. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the airworthiness requirements applicable in the State of Registry. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State Std. ref. A6-I-6.1.3 A6-I-6.1.3 A6-I-6.1.3 A6-I-6.1.3 A6-I-6.1.3 Cat. 2 2 2 3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A07 A07 A07 A07 A07 V 2.0 Page 56 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the airworthiness requirements applicable in the State of Registry. Note: - Attachment F contains guidance on the minimum equipment list.

Std. ref.

Cat.

SAFA Ramp Inspection Procedures Guidance material

Std.

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 57 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A08- 01 A08- 02 A08- 03 A08- 04 A08- 05 Pre-described Finding CofR format not in accordance with Annex 7 No English translation No fireproof identification plate Mismatch of data on CofR and identification plate No valid CofR or cannot be shown by crew somewhere else on the aircraft. Although it is not compliant to the requirements, the safety relevance is rather low and therefore no finding should be raised. certified by the issuing authority is carried on board. follow-up process the appropriate evidence is received that a valid document was issued at the time of the inspection, the finding should be downgraded to the Category 1 finding created for this purpose (see Chapter 4.3 above).

a) Its certificate of registration; cannot be shown by crew”.

Inspecting Instructions Check for presence and accuracy. In the case where only a photocopy is on board a finding should be made against “No valid CofR or Check if its format and content are in accordance with the requirements and whether translated into the English language. Check for fireproof identification plate (usually near the left forward door). Compare the data on the plate with that on the C of R. Note: Annex 7 requires that a fireproof plate needs to be installed near the main entrance. It is often found that the plate is located Note: Although ICAO does not specifically allow to carry other than the original of the document, it is considered acceptable if a copy Note: If the CofR was not found on board during the inspection, the Category 2 PDF reflecting this shall be used. However, if during the Standard’s Text The certificate of registration, in wording and arrangement, shall be a replica of the certificate shown in Figure 1. Note: - The size of the form is at the discretion of the State of Registry or common mark registering authority. When certificates of registration are issued in a language other than English, they shall include an English translation. An aircraft shall carry an identification plate inscribed with at least its nationality or common mark and registration mark. The plate shall be made of fireproof metal or other fireproof material of suitable physical properties and shall be secured to the aircraft in a prominent position near the main entrance or, in the case of an unmanned free balloon, affixed conspicuously to the exterior of the payload. An aircraft shall carry an identification plate inscribed with at least its nationality or common mark and registration mark. The plate shall be made of fireproof metal or other fireproof material of suitable physical properties and shall be secured to the aircraft in a prominent position near the main entrance or, in the case of an unmanned free balloon, affixed conspicuously to the exterior of the payload. Documents carried in aircraft Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention.

Std. ref. A7-7.1 A7-7.2 A7-8 A7-8 CC-29a Cat. 1 1 1 1 2

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Certificate of Registration Std. I I I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A08 Inspection Item A08 A08 A08 A08 A08 V 2.0 Page 58 of 217 Instructions for completing the detailed description PDF code A08- 06 Pre-described Finding A valid CofR was issued but not carried on board.

a) Its certificate of registration; Standard’s Text Documents carried in aircraft Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention.

Std. ref. CC-29a Cat. 1

SAFA Ramp Inspection Procedures Guidance material

Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A08 V 2.0 Page 59 of 217 Instructions for completing the detailed description PDF code A09- 01 Pre-described Finding Documents attesting noise certification inaccurate, not on board or cannot be produced by the crew Airworthiness. Such cases are in compliance with the ICAO requirements and do not constitute a finding. certified by the issuing authority is carried on board.

certification and whether translated in English language.

Inspecting Instructions Check for presence, accuracy (e.g. cross check MTOM, S/N with the ones specified in the C of R) of the document attesting noise Note: Certain States (e.g. United States, China) incorporate the noise certification data in the Aircraft Flight Manual and/or the Certificate of Note: Although ICAO does not specifically allow to carry other than the original of the document, it is considered acceptable if a copy Standard’s Text The documents attesting noise certification shall be approved by the State of Registry and shall be required by that State to be carried on the aircraft. 1.5 The documents attesting noise certification for an aircraft shall provide at least the following information: Item 1. Name of State. Item 2. Title of the noise document. Item 3. Number of the document. Item 4. Nationality or common mark and registration marks. Item 5. Manufacturer and manufacturer’s designation of aircraft. Item 6. Aircraft serial number. Item 7. Engine manufacturer, type and model. Item 8. Propeller type and model for propeller-driven aeroplanes. Item 9. Maximum take-off mass in kilograms. Item 10. Maximum landing mass, in kilograms, for certificates issued under Chapters 2, 3, 4, 5 and 12 of this Annex. Item 11. The chapter and section of this Annex according to which the aircraft was certificated. Item 12. Additional modifications incorporated for the purpose of compliance with the applicable noise certification Standards. Item 13. The lateral/full-power noise level in the corresponding unit for documents issued under Chapters 2, 3, 4, 5 and 12 of this Annex. Item 14. The approach noise level in the corresponding unit for documents issued under Chapters 2, 3, 4, 5, 8 and 12 of this Annex.

Std. ref. A16-I-II-1.4 A16-I-II-1.5 Cat. 1

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Noise Certificate Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A09 Inspection Item A09 V 2.0 Page 60 of 217 Instructions for completing the detailed description PDF code A09- 02 Pre-described Finding No English translation Standard’s Text Item 15. The flyover noise level in the corresponding unit for documents issued under Chapters 2, 3, 4, 5 and 12 of this Annex. Item 16. The overflight noise level in the corresponding unit for documents issued under Chapters 6, 8 and 11 of this Annex. Item 17. The take-off noise level in the corresponding unit for documents issued under Chapters 8 and 10 of this Annex. Item 18. Statement of compliance, including a reference to Annex 16, Volume I. Item 19. Date of issuance of the noise certification document. Item 20. Signature of the officer issuing it. An aeroplane shall carry a document attesting noise certification. When the document, or a suitable statement attesting noise certification as contained in another document approved by the State of Registry, is issued in a language other than English, it shall include an English translation. Note.- The attestation may be contained in any document, carried on board, approved by the State of Registry.

Std. ref. A6-I-6.13 Cat. 1

SAFA Ramp Inspection Procedures Guidance material

Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A09 V 2.0 Page 61 of 217 Instructions for completing the detailed description PDF code A10-01 Pre-described Finding Layout of the AOC and/or the OPS Specs not in accordance with provisions of Annex 6 compliance with the ICAO requirements, but the layout is different. dangerous goods or not. In case nothing is mentioned, and no other official document is available on board indicating the authorisation to transport dangerous goods, no finding should be raised for this reason only and the operator should be considered to be not approved. In the case the operator was actually or intending to transporting DG, a cat. 3 finding can be raised (“Commercial Air Transport operations not in accordance with the operations specifications”). copy, EU-OPS requires in OPS 1.125 that “the original or copy” is carried during each flight. Therefore, if an inspector finds a non-certified copy of the AOC on board this may not constitute a finding (however may be recorded as a cat. G remark). used. If no document is provided during the time of inspection, the aircraft can still be released as a non-commercial General Aviation flight. However, if during the follow-up process the appropriate evidence is received that a valid document was issued at the time of the inspection, the finding should be downgraded to the Category 1 finding created for this purpose (see Chapter 4.3 above).

Inspecting Instructions Check for presence and accuracy (including the Operations Specifications). Check if format (layout and content) of AOC and OPS Specs is in compliance with Annex 6 (including English translation if written in another language). If the AOC is not carried on board while engaged in commercial operations, apply the procedure described in chapter 4.3 above. Note 1: although ICAO requires a specific layout, no finding but a Category G remark should be raised if the content is in Note 2: ICAO Annex 6 requires that the operations specifications specifically mention whether the operator is entitled to transport If the AOC contains an expiration date, check if within the validity period. Check if the aircraft operation (inbound and outbound) is in compliance with the Operations Specifications (limitations, special authorisations: Low Visibility Operations (LVO), (B/P)RNAV, RVSM, MNPS, ETOPS, dangerous goods, and others required for the particular type of operation). Note: EU-OPS is less restrictive than ICAO on the carriage of a copy of the AOC on board: where ICAO requires a certified true Note: If the AOC and/or OPS Specs were not found on board during the inspection, the Category 3 PDF reflecting this shall be Standard’s Text The air operator certificate shall contain at least the following information and, from 1 January 2010, shall follow the layout of Appendix 6, paragraph 2: a) the State of the Operator and the issuing authority; b) the air operator certificate number and its expiration date; c) the operator name, trading name (if different) and address of the principal place of business; d) the date of issue and the name, signature and title of the authority representative; and e) the location, in a controlled document carried on board, where the contact details of operational management can be found.

Std. ref. A6-I-4.2.1.5/ A6-I- 4.2.1.6/ A6-I- 4.2.1.7 Cat. G

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title AOC or equivalent Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A10 Inspection Item A10 V 2.0 Page 62 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code A10-02 A10-03 A10-04 Pre-described Finding Information in the operations specifications not in accordance with Annex 6 Information in AOC incorrect No English translation Standard’s Text The operations specifications associated with the air operator certificate shall contain at least the information listed in Appendix 6, paragraph 3, and, from 1 January 2010, shall follow the layout of Appendix 6, paragraph 3. Air operator certificates and their associated operations specifications first issued from 20 November 2008 shall follow the layouts of Appendix 6, paragraphs 2 and 3 The operations specifications associated with the air operator certificate shall contain at least the information listed in Appendix 6, paragraph 3, and, from 1 January 2010, shall follow the layout of Appendix 6, paragraph 3. For each aircraft model in the operator’s fleet, identified by aircraft make, model and series, the following list of authorizations, conditions and limitations shall be included: issuing authority contact details, operator name and AOC number, date of issue and signature of the authority representative, aircraft model, types and area of operations, special limitations and authorizations. Note.— If authorizations and limitations are identical for two or more models, these models may be grouped in a single list. The air operator certificate shall contain at least the following information and, from 1 January 2010, shall follow the layout of Appendix 6, paragraph 2: a) the State of the Operator and the issuing authority; b) the air operator certificate number and its expiration date; c) the operator name, trading name (if different) and address of the principal place of business; d) the date of issue and the name, signature and title of the authority representative; and e) the location, in a controlled document carried on board, where the contact details of operational management can be found. An aeroplane shall carry a certified true copy of the air operator certificate specified in 4.2.1, and a copy of the operations specifications relevant to the aeroplane type, issued in conjunction with the certificate. When the certificate and the associated operations specifications are issued by the State of the Operator in a language other than English, an English translation Std. ref. A6-I-4.2.1.6 A6-I-APP6.3.1 A6-I-4.2.1.5 A6-I-6.1.2 Cat. 2 2 2

SAFA Ramp Inspection Procedures Guidance material

Std. I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A10 A10 A10 V 2.0 Page 63 of 217 Instructions for completing the detailed description Please provide additional information (specific type of operation) Indicate the particulars of the situation observed PDF code A10-05 A10-06 A10-07 A10-08 Pre-described Finding Commercial Air Transport operations not in accordance with the operations specifications Commercial Air Transport operations without a valid AOC No original nor copy of the AOC, and/or of the operations specifications on board or cannot be shown by the crew A valid AOC and/or operations specifications for the flights performed was issued but not carried on board at the time of the inspection.

Standard’s Text shall be included. Note.— Provisions for the content of the air operator certificate and its associated operations specifications are contained in 4.2.1.5 and 4.2.1.6. The air operator certificate shall authorize the operator to conduct commercial air transport operations in accordance with the operations specifications. Note.— Provisions for the content of the air operator certificate and its associated operations specifications are contained in 4.2.1.5 and 4.2.1.6. An operator shall not engage in commercial air transport operations unless in possession of a valid air operator certificate issued by the State of the Operator. An aeroplane shall carry a certified true copy of the air operator certificate specified in 4.2.1, and a copy of the operations specifications relevant to the aeroplane type, issued in conjunction with the certificate. When the certificate and the associated operations specifications are issued by the State of the Operator in a language other than English, an English translation shall be included. Note.— Provisions for the content of the air operator certificate and its associated operations specifications are contained in 4.2.1.5 and 4.2.1.6. An aeroplane shall carry a certified true copy of the air operator certificate specified in 4.2.1, and a copy of the operations specifications relevant to the aeroplane type, issued in conjunction with the certificate. When the certificate and the associated operations specifications are issued by the State of the Operator in a language other than English, an English translation shall be included. Note.— Provisions for the content of the air operator certificate and its associated operations specifications are contained in 4.2.1.5 and 4.2.1.6.

Std. ref. A6-I-4.2.1.2 A6-I-4.2.1.1 A6-I-6.1.2 A6-I-6.1.2 Cat. 3 3 3 1

SAFA Ramp Inspection Procedures Guidance material

Std. I I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A10 A10 A10 A10 V 2.0 ICAO Page 64 of 217 Instructions for completing the detailed description Indicate what is incorrect PDF code A11-01 A11-02 A11-03 A11-04 Pre-described Finding Incorrect information on the Radio Station Licence A valid Radio Station Licence was issued but not carried on board at the time of the inspection. No Radio Station Licence issued Radio Station Licence on board expired does not specify the information to be mentioned on the Radio Licence. The requirement to have a radio licence is originating from Article 18 of the Radio Regulations from the International Telecommunications Union, which requires the issuing State to include, besides the name/callsign, “the general characteristics of the installation” into the licence. However, the exact content of such a licence is only given by the ITU as a recommendation only (Recommendation 7 Rev. WRC-97). Therefore no finding should be raised on the content of the radio licence, unless the mentioned information is incorrect. by the issuing authority is carried on board. described in Chapter 4.3 above. only.

Inspecting Instructions Check for presence and accuracy. Check for the correct name/callsign. Note: Following the Articles 29e and 30 of the Chicago Convention, a radio licence is a licence to install radio transmitting apparatus. Note: Although ICAO does not specifically allow to carry other than the original of the document, it is considered acceptable if a copy certified Note: If the Radio Licence is not carried on board during the inspection while engaged in commercial operations, apply the procedure Note: Certain Radio Licences contain expiration date. If a Radio Licence if found to be expired, this should be recorded as a General Remark Standard’s Text Aircraft of each contracting State may, in or over the territory of other contracting States, carry radio transmitting apparatus only if a Licence to install and operate such apparatus has been issued by the appropriate authorities of the State in which the aircraft is registered. The use of radio transmitting apparatus in the territory of the contracting State whose territory is flown over shall be in accordance with the regulations prescribed by that State. Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention: e) If it is equipped with radio apparatus, the aircraft radio station licence. Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention: e) If it is equipped with radio apparatus, the aircraft radio station licence. Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention: e) If it is equipped with radio apparatus, the aircraft radio station licence.

Std. ref. CC-30a CC-29e CC-29e CC-29e Cat. 1 1 2 G

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Radio Licence Std. I I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A11 Inspection Item A11 A11 A11 A11 V 2.0 Page 65 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A12- 01 A12- 02 A12- 03 A12- 04 A12- 05 Pre-described Finding Format of CofA not in accordance with Annex 8 requirements No English translation CofA not issued nor rendered valid by the State of registry A valid CofA was issued but not carried on board at the time of the inspection. Endorsed CofA without permission of the State of inspection 3 finding. The aircraft should be allowed to depart only after receiving positive confirmation from the State of registry that the aircraft has a valid CofA. are usually supplemented by a separate document (ARC – Airworthiness Review Certificate) which should indicate its validity. certified by the issuing authority is carried on board. the follow-up process (including the required action to be taken by the airline during the course of the ramp inspection) the appropriate evidence is received that a valid document was issued at the time of the inspection, the finding should be downgraded to the Category 1 finding created for this purpose (see Chapter 4.3 above).

Chapter 4.3 above.

Inspecting Instructions Check for presence, accuracy and validity. If no original (or certified copy) CoA is carried on board, apply the procedure described in Check if its content is in compliance with the requirement (including English translation if written in another language). Note: In the case where an aircraft is identified without an original (or certified true copy) and valid CofA then this is considered a cat. Note: Certain States (e.g. EASA states) issue Certificates of Airworthiness which do not mention an expiration date. Such certificates Note: Although ICAO does not specifically allow to carry other than the original of the document, it is considered acceptable if a copy Note: If the CofA was not found on board during the inspection, the Category 3 PDF reflecting this shall be used. However, if during Standard’s Text The Certificate of Airworthiness shall contain the information shown in Figure 1 and shall be generally similar to it. When Certificates of Airworthiness are issued in a language other than English, they shall include an English translation. Note - Article 29 of the Convention on International Civil Aviation requires that the Certificate of Airworthiness be carried on board every aircraft engaged in international air navigation. Every aircraft engaged in international navigation shall be provided with a certificate of airworthiness issued or rendered valid by the State in which it is registered. Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention: b) Its certificate of airworthiness; Endorsement of certificates and licences a) Any aircraft or part thereof with respect to which there Std. ref. A8-II-3.3.1 A8-II-3.3.2 CC-31 CC-29b CC-39a Cat. 1 3 1 2 3 Inspections Item Title Certificate of Airworthiness Std. I I I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A12 Inspection Item A12 A12 A12 A12 A12 V 2.0 Page 66 of 217 Instructions for completing the detailed description PDF code A12- 06 Pre-described Finding No valid CofA on board.

Standard’s Text exists an international standard of airworthiness or performance, and which failed in any respect to satisfy that standard at the time of its certification, shall have endorsed on or attached to its airworthiness certificate a complete enumeration of the details in respect of which it so failed. Validity of endorsed certificates and licences No aircraft or personnel having certificates or licences so endorsed shall participate in international navigation, except with the permission of the State or States whose territory is entered. The registration or use of any such aircraft, or of any certificated aircraft part, in any State other than that in which it was originally certificated shall be at the discretion of the State into which the aircraft or part is imported. Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention: b) Its certificate of airworthiness; Std. ref. CC-40 CC-29b Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A12 V 2.0 Page 67 of 217 calculations, this should not be raised as a finding. If it was not taken into account, a finding should be raised on the performance and/or mass and balance calculation. of ground and/or water facilities. As long as the flight crew is aware of it, there is no requirement to carry on board the Notams and no finding should be raised. In order to verify if the crew is indeed aware (in the absence of Notams on board, the inspector could verify the awareness of the information in the Notams published for the airport of inspection (or the alternates). operation, edited as required. of repetitive flight plans (RPL). In the latter case, a contact should be mentioned on the flight plan where ATC can obtain information with regard to the selected alternates for the concerned flight (see Doc. 4444, Chapter 16.4.2.2).

the take-off of the aircraft.

Inspecting Instructions Check for presence and accuracy of Operational Flight Plan (including signature of PIC). Compare with the relevant instructions the OPS Manual. Check for proper filing system (retaining of all relevant flight preparation documents). Check for proper performance and fuel calculation. Note: In case the actual fuel on board is more than calculated, but it is taken into account in the performance and mass and balance Check the fuel consumption monitoring of the incoming flight (if required by the OPS manual). Check if the operator has selected appropriate alternate aerodromes (if required). Check whether the flight crew has reviewed all the meteorological information (including for alternate aerodromes). Note: in line with the previous note, A6-I-4.3.5.2 only requires that the IFR flight “(…) shall not be commenced unless information is available which indicates that (…)”; there is no requirement that the information needs to be on board. The inspector could verify if such information is/was available to the flight crew before departure for the outbound flight. Check if the crew ensured that the weather forecast at the destination or the destination alternate aerodrome is above minima. Check whether the flight crew has reviewed the applicable NOTAMS and/or pre-flight information bulletins (including those for alternate aerodromes). Note: From the standard A6-I-4.1.1 it results that the operator/flight crew has to be aware of the availability (usually published in Notams) Note: Operators with a flight dispatch department may only provide the crew with NOTAMS considered necessary for their particular In case of ground icing conditions, check if the proper de/anti-icing procedures have been carried out or planned to be carried out prior to Check for the presence and accuracy of the ATC flight plan. Note: Alternate airports do not always need to be mentioned on the ATC flight plan, e.g. flight allowed without an alternate or in the case Note: depending of the type of operations, the item 10 of the flight plan shall contain the following designators: “R” for B-RNAV operations; “P” for P-RNAV operations (in addition to “R”); “Y” for flights in (portions of) airspace where the carriage of 8.33 KHz capable radio equipment is mandatory; “W” for RVSM operations; “S” for aircraft equipped with Mode-S Transponder.

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Flight Preparation SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A13 V 2.0 Page 68 of 217 Instructions for completing the detailed description Indicate why the ATC flight plan is incorrect PDF code A13- 01 A13- 02 A13- 03 Pre-described Finding No copy of the operational flight plan retained on the ground Operational flight plan not signed by the PIC ATC Flight plan incorrect Standard’s Text flight. The operational flight plan shall be approved and signed by the pilot-in-command and, where applicable, signed by the flight operations officer/flight dispatcher, and a copy shall be filed with the operator or a designated agent, or, if these procedures are not possible, it shall be left with the aerodrome authority or on record in a suitable place at the point of departure. flight. The operational flight plan shall be approved and signed by the pilot-in-command and, where applicable, signed by the flight operations officer/flight dispatcher, and a copy shall be filed with the operator or a designated agent, or, if these procedures are not possible, it shall be left with the aerodrome authority or on record in a suitable place at the point of departure. A flight plan shall comprise information regarding such of the following items as are considered relevant by the appropriate ATS authority: — Aircraft identification — Flight rules and type of flight — Number and type(s) of aircraft and wake turbulence category — Equipment — Departure aerodrome (see Note 1) — Estimated off-block time (see Note 2) — Cruising speed(s) — Cruising level(s) — Route to be followed — Destination aerodrome and total estimated elapsed time — Alternate aerodrome(s) — Fuel endurance — Total number of persons on board — Emergency and survival equipment — Other information. Operators of aircraft approved for basic area navigation (B-RNAV) operations, as set out in 4.1.1.5.2, shall insert the designator “R” in Item 10 of the flight plan. Operators of aircraft approved for precision area navigation (P- RNAV) operations, as set out in 4.1.1.5.2, shall, in addition to the An operational flight plan shall be completed for every intended An operational flight plan shall be completed for every intended Std. ref. A6-I-4.3.3.1 A6-I-4.3.3.1 A2-3.3.2 EUR 2.1.2.1 EUR 2.1.2.2 Cat. 1 1 2

SAFA Ramp Inspection Procedures Guidance material

Std. I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A13 A13 A13 V 2.0 Page 69 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text designator “R”, also insert the designator “P” in Item 10 of the flight plan. to meet the P-RNAV functionality and accuracy requirements of 4.1.1.5.2.4 before departure, the operator of the aircraft shall not insert the designator “P” in Item 10 of the flight plan. Subsequently, for a flight for which a flight plan has been submitted, an appropriate new flight plan shall be submitted and the old flight plan cancelled. For a flight operating based on a repetitive flight plan (RPL), the RPL shall be cancelled and an appropriate new flight plan shall be submitted. being unable to meet the B-RNAV functionality and accuracy requirements of 4.1.1.5.2.6 before departure, the operator of the aircraft shall not insert the designators “S” or “R” or “P” in Item 10 of the flight plan. Since such flights require special handling by ATC, Item 18 of the flight plan shall contain STS/RNAVINOP. Subsequently, for a flight for which a flight plan has been submitted, an appropriate new flight plan shall be submitted and the old flight plan cancelled. For a flight operating based on an RPL, the RPL shall be cancelled and an appropriate new flight plan shall be submitted. For flights conducted wholly or partly in the volume of airspace where the carriage of 8.33 kHz channel spacing radio equipment is mandatory, as specified in 3.2.1, in addition to the letter S and/or any other letters, as appropriate, the letter Y shall be inserted in Item 10 of the flight plan for aircraft equipped with 8.33 kHz channel spacing capable radio equipment, or the indicator STS/EXM833 shall be included in Item 18 for aircraft not equipped but which have been granted exemption from the mandatory carriage requirement. Aircraft normally capable of operating above FL 195 but planning to fly below this level shall include the letter Y as specified above. In case of a change in the 8.33 kHz capability status for a flight planned to operate in the area specified in 3.2.1, a modification message shall be sent with the appropriate indicator inserted in the relevant Item. Operators of RVSM approved aircraft shall indicate the approval status by inserting the letter W in Item 10 of the ICAO flight plan Where a failure or degradation results in the aircraft being unable In addition, where a failure or degradation results in the aircraft Std. ref. EUR 2.1.2.4 EUR 2.1.2.5 EUR 2.1.8.1 EUR 2.1.8.2 EUR 2.1.5.1 Cat.

SAFA Ramp Inspection Procedures Guidance material

Std.

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 70 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text form, regardless of the requested flight level. Operators of RVSM approved aircraft shall also include the letter W in Item Q of the RPL, regardless of the requested flight level. If a change of aircraft operated in accordance with an RPL results in a modification of the RVSM approval status as stated in Item Q, a modification message (CHG) shall be submitted by the operator. Operators of non-RVSM approved aircraft intending to operate from a departure aerodrome outside the lateral limits of RVSM airspace at a cruising level of FL 290 or above to a destination aerodrome within the lateral limits of RVSM airspace shall include the following in Item 15 of the flight plan form: a) the entry point at the lateral limits of RVSM airspace; and b) the requested flight level below FL 290 for that portion of the route commencing at the entry point. Note.— Refer to 6.10.2.4.1 for related ATC requirements. Operators of non-RVSM approved aircraft intending to operate from a departure aerodrome to a destination aerodrome, both of which are within the lateral limits of RVSM airspace, shall include in Item 15 of the ICAO flight plan form, a requested cruising level below FL 290. Note.— Refer to 6.10.2.4.2 for related ATC requirements. Operators of non-RVSM approved aircraft intending to operate from a departure aerodrome within the lateral limits of RVSM airspace to a destination aerodrome outside the lateral limits of RVSM airspace at a cruising level of FL 290 or above shall include the following in Item 15 of the ICAO flight plan form: a) a requested flight level below FL 290 for that portion of the route within the lateral limits of RVSM airspace; and b) the exit point at the lateral limits of RVSM airspace and the requested flight level for that portion of the route commencing at the exit point. Note.— Refer to 6.10.2.4.3 for related ATC requirements.

Std. ref. EUR 2.1.5.2 EUR 2.1.6.2 EUR 2.1.6.3 EUR 2.1.6.4 Cat.

SAFA Ramp Inspection Procedures Guidance material

Std.

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 71 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A13- 04 A13- 05 Pre-described Finding Content and use of the Operational Flight plan not in accordance with the operations manual Fuel on board less than minimum ICAO requirements Standard’s Text A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in command is satisfied that: f) a check has been completed indicating that the operating limitations of Chapter 5 can be complied with for the flight to be undertaken; and g) the Standards of 4.3.3 relating to operational flight planning have been complied with. Before beginning a flight, the pilot-in-command of an aircraft shall become familiar with all available information appropriate to the intended operation. Pre-flight action for flights away from the vicinity of an aerodrome, and for all IFR flights, shall include a careful study of available current weather reports and forecasts, taking into consideration fuel requirements and an alternative course of action if the flight cannot be completed as planned. A flight shall not be commenced unless, taking into account both the meteorological conditions and any delays that are expected in flight, the aeroplane carries sufficient fuel and oil to ensure that it can safely complete the flight. In addition, a reserve shall be carried to provide for contingencies. In computing the fuel and oil required in 4.3.6.1 at least the following shall be considered: a) meteorological conditions forecast; b) expected air traffic control routings and traffic delays; c) for IFR flight, one instrument approach at the destination aerodrome, including a missed approach; d) the procedures prescribed in the operations manual for loss of pressurization, where applicable, or failure of one power-unit while en route; and e) any other conditions that may delay the landing of the aeroplane or increase fuel and/or oil consumption. A flight shall not be commenced unless the performance information provided in the flight manual indicates that the Standards of 5.2.6 to 5.2.11 can be complied with for the flight to be undertaken.

Std. ref. A6-I- 4.3.1(f)(g) A2-2.3.2 A6-I-4.3.6.1 A6-I-4.3.6.4 A6-I-5.2.5 Cat. 2 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A13 A13 V 2.0 Page 72 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate why the OFP is incorrect Indicate the selected aerodrome(s) and why they are unsuitable PDF code A13- 06 A13- 07 A13- 08 A13- 09 A13- 10 A13- 11 Pre-described Finding Flight crew unaware of the applicable departure, destination or alternate airports NOTAMs. Flight operated in known icing conditions without suitable certification and/or equipment No icing inspection performed by crew or ground staff with ground icing conditions Incorrect Operational Flight Plan No Operational Flight Plan No or unsuitable alternate(s) airports selected Standard’s Text commenced unless it has been ascertained by every reasonable means available that the ground and/or water facilities available and directly required on such flight, for the safe operation of the aeroplane and the protection of the passengers, are adequate for the type of operation under which the flight is to be conducted and are adequately operated for this purpose. Note.- "Reasonable means" in this Standard is intended to denote the use, at the point of departure, of information available to the operator either through official information published by the aeronautical information services or readily obtainable from other sources. A flight to be operated in known or expected icing conditions shall not be commenced unless the aeroplane is certificated and equipped to cope with such conditions. known ground icing conditions shall not take off unless the aeroplane has been inspected for icing and, if necessary, has been given appropriate de-icing/anti-icing treatment. Accumulation of ice or other naturally occurring contaminants shall be removed so that the aeroplane is kept in an airworthy condition prior to take-off. flight. The operational flight plan shall be approved and signed by the pilot-in-command and, where applicable, signed by the flight operations officer/flight dispatcher, and a copy shall be filed with the operator or a designated agent, or, if these procedures are not possible, it shall be left with the aerodrome authority or on record in a suitable place at the point of departure. flight. The operational flight plan shall be approved and signed by the pilot-in-command and, where applicable, signed by the flight operations officer/flight dispatcher, and a copy shall be filed with the operator or a designated agent, or, if these procedures are not possible, it shall be left with the aerodrome authority or on record in a suitable place at the point of departure. 4.3.4.1.1 A take-off alternate aerodrome shall be selected and specified in the operational flight plan if the weather conditions at the aerodrome of departure are at or below the applicable An operator shall ensure that a flight will not be A flight to be planned or expected to operate in suspected or An operational flight plan shall be completed for every intended An operational flight plan shall be completed for every intended Std. ref. A6-I-4.1.1 A6-I-4.3.5.3 A6-I-4.3.5.4 A6-I-4.3.3.1 A6-I-4.3.3.1 A6-I-4.3.4.1 Cat. 3 3 3 2 3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I I I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A13 A13 A13 A13 A13 A13 V 2.0 Page 73 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text aerodrome operating minima or it would not be possible to return to the aerodrome of departure for other reasons. 4.3.4.1.2 The take-off alternate aerodrome shall be located within the following distance from the aerodrome of departure: a) aeroplanes having two power-units. Not more than a distance equivalent to a flight time of one hour at the single-engine cruise speed; and b) aeroplanes having three or more power-units. Not more than a distance equivalent to a flight time of two hours at the one-engine inoperative cruise speed. 4.3.4.1.3 For an aerodrome to be selected as a take-off alternate the available information shall indicate that, at the estimated time of use, the conditions will be at or above the aerodrome operating minima for that operation. range operations by aeroplanes with two turbine engines, shall be selected and specified in the operational and air traffic services (ATS) flight plans. For a flight to be conducted in accordance with the instrument flight rules, at least one destination alternate aerodrome shall be selected and specified in the operational and ATS flight plans, unless: a) the duration of the flight and the meteorological conditions prevailing are such that there is reasonable certainty that, at the estimated time of arrival at the aerodrome of intended landing, and for a reasonable period before and after such time, the approach and landing may be made under visual meteorological conditions; or b) the aerodrome of intended landing is isolated and there is no suitable destination alternate aerodrome.

En-route alternate aerodromes, required by 4.7 for extended Std. ref. A6-I-4.3.4.2 A6-I-4.3.4.3 Cat.

SAFA Ramp Inspection Procedures Guidance material

Std.

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 74 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A13- 12 A13- 13 Pre-described Finding No weather forecast available indicating that the destination or destination alternate aerodrome conditions are at or above minima Performance and/or fuel calculation not available or significantly incorrect for the flight Standard’s Text A flight to be conducted in accordance with instrument flight rules shall not be commenced unless information is available which indicates that conditions at the aerodrome of intended landing or, where a destination alternate is required, at least one destination alternate aerodrome will, at the estimated time of arrival, be at or above the aerodrome operating minima. Note.- It is the practice in some States to declare, for flight planning purposes, higher minima for an aerodrome when nominated as a destination alternate than for the same aerodrome when planned as that of intended landing. become familiar with all available information appropriate to the intended operation. Pre-flight action for flights away from the vicinity of an aerodrome, and for all IFR flights, shall include a careful study of available current weather reports and forecasts, taking into consideration fuel requirements and an alternative course of action if the flight cannot be completed as planned. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in command is satisfied that: f) a check has been completed indicating that the operating limitations of Chapter 5 can be complied with for the flight to be undertaken; and g) the Standards of 4.3.3 relating to operational flight planning have been complied with. the meteorological conditions and any delays that are expected in flight, the aeroplane carries sufficient fuel and oil to ensure that it can safely complete the flight. In addition, a reserve shall be carried to provide for contingencies. following shall be considered: a) meteorological conditions forecast; b) expected air traffic control routings and traffic delays; c) for IFR flight, one instrument approach at the destination aerodrome, including a missed approach; Before beginning a flight, the pilot-in-command of an aircraft shall A flight shall not be commenced unless, taking into account both In computing the fuel and oil required in 4.3.6.1 at least the Std. ref. A6-I-4.3.5.2 A2-2.3.2 A6-I- 4.3.1(f)(g) A6-I-4.3.6.1 A6-I-4.3.6.4 Cat. 3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A13 A13 V 2.0 Page 75 of 217 Instructions for completing the detailed description Indicate what en-route alternate(s) was not available PDF code A13- 14 A13- 15 Pre-described Finding Required en-route alternate(s) (ETOPS) not available Actual weather and weather forecast not checked before departure Standard’s Text d) the procedures prescribed in the operations manual for loss of pressurization, where applicable, or failure of one power-unit while en route; and e) any other conditions that may delay the landing of the aeroplane or increase fuel and/or oil consumption. information provided in the flight manual indicates that the Standards of 5.2.6 to 5.2.11 can be complied with for the flight to be undertaken. shall not be commenced unless, during the possible period of arrival, the required en-route alternate aerodrome(s) will be available and the available information indicates that conditions at those aerodromes will be at or above the aerodrome operating minima approved for the operation. become familiar with all available information appropriate to the intended operation. Pre-flight action for flights away from the vicinity of an aerodrome, and for all IFR flights, shall include a careful study of available current weather reports and forecasts, taking into consideration fuel requirements and an alternative course of action if the flight cannot be completed as planned. the meteorological conditions and any delays that are expected in flight, the aeroplane carries sufficient fuel and oil to ensure that it can safely complete the flight. In addition, a reserve shall be carried to provide for contingencies. following shall be considered: a) meteorological conditions forecast; b) expected air traffic control routings and traffic delays; c) for IFR flight, one instrument approach at the destination aerodrome, including a missed approach; d) the procedures prescribed in the operations manual for loss of pressurization, where applicable, or failure of one power-unit while en route; and e) any other conditions that may delay the landing of the aeroplane or increase fuel and/or oil consumption.

A flight shall not be commenced unless the performance A flight to be conducted in accordance with 4.7.1 Before beginning a flight, the pilot-in-command of an aircraft shall A flight shall not be commenced unless, taking into account both In computing the fuel and oil required in 4.3.6.1 at least the Std. ref. A6-I-5.2.5 A6-I-4.7.3 A2-2.3.2 A6-I-4.3.6.1 A6-I-4.3.6.4 Cat. 3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A13 A13 V 2.0 Page 76 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the applicable reference in the OPS Manual requiring the flight crew to carry out in- flight fuel consumption monitoring PDF code A13- 16 A13- 17 A13- 18 Pre-described Finding Weather on required en-route alternate(s) below ETOPS minima Alternate airport(s) (or indication of operators’ contacts in case of RPL) considered in OFP but not specified in the ATS flight plan No fuel consumption monitoring performed when required by the OPS Manual Standard’s Text information provided in the flight manual indicates that the Standards of 5.2.6 to 5.2.11 can be complied with for the flight to be undertaken. shall not be commenced unless, during the possible period of arrival, the required en-route alternate aerodrome(s) will be available and the available information indicates that conditions at those aerodromes will be at or above the aerodrome operating minima approved for the operation. range operations by aeroplanes with two turbine power-units, shall be selected and specified in the operational and air traffic services (ATS) flight plans. En-route alternate aerodromes, required by 4.7 for extended range operations by aeroplanes with two turbine engines, shall be selected and specified in the operational and air traffic services (ATS) flight plans. Destination alternate aerodromes For a flight to be conducted in accordance with the instrument flight rules, at least one destination alternate aerodrome shall be selected and specified in the operational and ATS flight plans, unless: a) the duration of the flight and the meteorological conditions prevailing are such that there is reasonable certainty that, at the estimated time of arrival at the aerodrome of intended landing, and for a reasonable period before and after such time, the approach and landing may be made under visual meteorological conditions; or b) the aerodrome of intended landing is isolated and there is no suitable destination alternate aerodrome.

A flight shall not be commenced unless the performance A flight to be conducted in accordance with 4.7.1 En-route alternate aerodromes, required by 4.7 for extended Std. ref. A6-I-5.2.5 A6-I-4.7.3 A6-I-4.3.4.2 A6-I-4.3.4.2 A6-I-4.3.4.3 Cat. 3 2 G

SAFA Ramp Inspection Procedures Guidance material

Std. I I O SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A13 A13 A13 V 2.0 Page 77 of 217 Instructions for completing the detailed description Provide further information as to why the calculations are incorrect.

PDF code A14-01 Pre-described Finding Incorrect mass and/or balance calculations, within a/c limits, and having no effect on the performance calculations.

performance calculations.

calculations. noise certification.

Inspecting Instructions Check for presence of a completed mass and balance sheet (either paper or digital format) and accuracy of the mass and balance Check if the actual load distribution is properly reflected in the M&B Sheet. If mass and/or balance calculations are found to be incorrect check whether still within the a/c limits and check the influence on the Note: If additional fuel was loaded, check that it is included on the Weight and balance documentation. Check if the crew has sufficient data available (in the OPS manual or AFM) to verify the Mass & balance calculations. Check whether the mass and balance calculations account for any operational (MTOM) restriction as a result of reduced MTOM for Standard’s Text a) The mass of the aeroplane at the start of take-off shall not exceed the mass at which 5.2.8 is complied with, nor the mass at which 5.2.9, 5.2.10 and 5.2.11 are complied with, allowing for expected reductions in mass as the flight proceeds, and for such fuel jettisoning as is envisaged in applying 5.2.9 and 5.2.10 and, in respect of alternate aerodromes, 5.2.7 c) and 5.2.11. b) In no case shall the mass at the start of take-off exceed the maximum take-off mass specified in the flight manual for the pressure-altitude appropriate to the elevation of the aerodrome, and, if used as a parameter to determine the maximum take-off mass, any other local atmospheric condition. c) In no case shall the estimated mass for the expected time of landing at the aerodrome of intended landing and at any destination alternate aerodrome, exceed the maximum landing mass specified in the flight manual for the pressure- altitude appropriate to the elevation of those aerodromes, and if used as a parameter to determine the maximum landing mass, any other local atmospheric condition. d) In no case shall the mass at the start of take-off, or at the expected time of landing at the aerodrome of intended landing and at any destination alternate aerodrome, exceed the relevant maximum masses at which compliance has been demonstrated with the applicable noise certification Std. ref. A6-I-5.2.7 Cat. 2

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Weight and Balance sheet Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A14 Inspection Item A14 V 2.0 Page 78 of 217 Instructions for completing the detailed description Provide further information as to why the calculations are incorrect.

PDF code A14-02 Pre-described Finding Incorrect mass and/or balance calculations, within a/c limits, but affecting the performance calculations.

Standard’s Text Standards in Annex 16, Volume I, unless otherwise authorized in exceptional circumstances for a certain aerodrome or a runway where there is no noise disturbance problem, by the competent authority of the State in which the aerodrome is situated. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: d) the mass of the aeroplane and centre of gravity location are such that the flight can be conducted safely, taking into account the flight conditions expected; e) any load carried is properly distributed and safely secured. a) The mass of the aeroplane at the start of take-off shall not exceed the mass at which 5.2.8 is complied with, nor the mass at which 5.2.9, 5.2.10 and 5.2.11 are complied with, allowing for expected reductions in mass as the flight proceeds, and for such fuel jettisoning as is envisaged in applying 5.2.9 and 5.2.10 and, in respect of alternate aerodromes, 5.2.7 c) and 5.2.11. b) In no case shall the mass at the start of take-off exceed the maximum take-off mass specified in the flight manual for the pressure-altitude appropriate to the elevation of the aerodrome, and, if used as a parameter to determine the maximum take-off mass, any other local atmospheric condition. c) In no case shall the estimated mass for the expected time of landing at the aerodrome of intended landing and at any destination alternate aerodrome, exceed the maximum landing mass specified in the flight manual for the pressure- altitude appropriate to the elevation of those aerodromes, and if used as a parameter to determine the maximum landing mass, any other local atmospheric condition. d) In no case shall the mass at the start of take-off, or at the expected time of landing at the aerodrome of intended landing and at any destination alternate aerodrome, exceed the relevant maximum masses at which compliance has been demonstrated with the applicable noise certification Std. ref. A6-I-4.3.1(d)(e) A6-I-5.2.7 Cat. 3

SAFA Ramp Inspection Procedures Guidance material

Std. I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A14 V 2.0 Page 79 of 217 Instructions for completing the detailed description Provide further information as to what in particular cannot be checked by the crew on the Mass & balance calculations Indicate the particulars of the situation observed PDF code A14-03 A14-04 Pre-described Finding Insufficient data to enable the crew to check the Mass & balance calculations Mass & balance outside operational limits Standard’s Text Standards in Annex 16, Volume I, unless otherwise authorized in exceptional circumstances for a certain aerodrome or a runway where there is no noise disturbance problem, by the competent authority of the State in which the aerodrome is situated. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: d) the mass of the aeroplane and centre of gravity location are such that the flight can be conducted safely, taking into account the flight conditions expected; e) any load carried is properly distributed and safely secured. a) The mass of the aeroplane at the start of take-off shall not exceed the mass at which 5.2.8 is complied with, nor the mass at which 5.2.9, 5.2.10 and 5.2.11 are complied with, allowing for expected reductions in mass as the flight proceeds, and for such fuel jettisoning as is envisaged in applying 5.2.9 and 5.2.10 and, in respect of alternate aerodromes, 5.2.7 c) and 5.2.11. b) In no case shall the mass at the start of take-off exceed the maximum take-off mass specified in the flight manual for the pressure-altitude appropriate to the elevation of the aerodrome, and, if used as a parameter to determine the maximum take-off mass, any other local atmospheric condition. c) In no case shall the estimated mass for the expected time of landing at the aerodrome of intended landing and at any destination alternate aerodrome, exceed the maximum landing mass specified in the flight manual for the pressure- altitude appropriate to the elevation of those aerodromes, and if used as a parameter to determine the maximum landing mass, any other local atmospheric condition. d) In no case shall the mass at the start of take-off, or at the expected time of landing at the aerodrome of intended landing and at any destination alternate aerodrome, exceed the relevant maximum masses at which compliance has been demonstrated with the applicable noise certification Standards in Annex 16, Volume I, unless otherwise authorized in exceptional circumstances for a certain Std. ref. A6-I-4.3.1(d)(e) A6-I-5.2.7 Cat. 2 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A14 A14 V 2.0 Page 80 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code A14-05 A14-06 A14-07 Pre-described Finding Load sheet does not reflect actual load distribution but within A/C limits No mass and balance calculations performed No completed mass and balance sheet on board Standard’s Text aerodrome or a runway where there is no noise disturbance problem, by the competent authority of the State in which the aerodrome is situated. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: d) the mass of the aeroplane and centre of gravity location are such that the flight can be conducted safely, taking into account the flight conditions expected; e) any load carried is properly distributed and safely secured. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: d) the mass of the aeroplane and centre of gravity location are such that the flight can be conducted safely, taking into account the flight conditions expected; e) any load carried is properly distributed and safely secured. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: d) the mass of the aeroplane and centre of gravity location are such that the flight can be conducted safely, taking into account the flight conditions expected; e) any load carried is properly distributed and safely secured.

Std. ref. A6-I-4.3.1(d)(e) A6-I-4.3.1(d)(e) A6-I-4.3.1(d)(e) Cat. 2 3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A14 A14 A14 V 2.0 Page 81 of 217 Instructions for completing the detailed description Provide further information as to where the HFE was found and where it is its indicated location PDF code A15-01 A15-02 Pre-described Finding HFE not at indicated location HFE not marked with the appropriate operating instructions to verify compliance with the applicable (M) and/or (O) provisions. If the latter MEL actions have not been applied, a finding should be raised using the "detection/reporting/assessment of significant technical defect" procedure (see chapter 4.2 of the ramp inspection procedure). systems to monitor the condition of the extinguishers. An extinguisher without a date does not necessarily constitute a finding. However, if the expiry date (or next inspection date) is overdue, consider as unserviceable.

gauge (if installed), check expiration date (if any)). If considerably low weight consider unserviceable.

Inspecting Instructions Check if the installed extinguisher(s) is at the indicated location and easily accessible. Check if the installed extinguisher(s) is marked with the appropriate operating instructions. Check if the installed extinguisher(s) (including the extinguishing agent release mechanism) is serviceable (check pressure Note: Often HFEs in excess of those required (by MEL provisions) may be U/S, however in such a case, check against the MEL Note: ICAO does not require hand fire extinguishers to have an expiration (or next check) date. Operators may employ various Standard’s Text An aeroplane shall be equipped with: b) portable fire extinguishers of a type which, when discharged, will not cause dangerous contamination of the air within the aeroplane. At least one shall be located in: 1) the pilot's compartment; and 2) each passenger compartment that is separate from the pilot's compartment and that is not readily accessible to the flight crew; Note.- Any portable fire extinguisher so fitted in accordance with the certificate of airworthiness of the aeroplane may count as one prescribed. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. An aeroplane shall be equipped with: b) portable fire extinguishers of a type which, when discharged, will not cause dangerous contamination of the air within the aeroplane. At least one shall be located in: 1) the pilot's compartment; and Std. ref. A6-I-6.2.2b A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 A6-I-6.2.2b Cat.

2 2

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Hand Fire Extinguishers Std. I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A15 Inspection Item A15 A15 V 2.0 Page 82 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code A15-03 A15-04 Pre-described Finding HFE empty, unserviceable or missing (outside MEL limits) HFE not accessible Standard’s Text 2) each passenger compartment that is separate from the pilot's compartment and that is not readily accessible to the flight crew; Note.- Any portable fire extinguisher so fitted in accordance with the certificate of airworthiness of the aeroplane may count as one prescribed. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. An aeroplane shall be equipped with: b) portable fire extinguishers of a type which, when discharged, will not cause dangerous contamination of the air within the aeroplane. At least one shall be located in: 1) the pilot's compartment; and 2) each passenger compartment that is separate from the pilot's compartment and that is not readily accessible to the flight crew; Note.- Any portable fire extinguisher so fitted in accordance with the certificate of airworthiness of the aeroplane may count as one prescribed. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. An aeroplane shall be equipped with: b) portable fire extinguishers of a type which, when discharged, will not cause dangerous contamination of the air within the aeroplane. At least one shall be located in: 1) the pilot's compartment; and 2) each passenger compartment that is separate from the pilot's compartment and that is not readily accessible to the flight crew; Note.- Any portable fire extinguisher so fitted in accordance with the certificate of airworthiness of the aeroplane may count as one prescribed.

Std. ref. A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 A6-I-6.2.2b A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 A6-I-6.2.2b Cat.

3 3

SAFA Ramp Inspection Procedures Guidance material

Std. I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A15 A15 V 2.0 Page 83 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked.

Std. ref. A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 Cat.

SAFA Ramp Inspection Procedures Guidance material

Std.

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 84 of 217 Instructions for completing the detailed description Provide further clarification as to why the required life jackets/flotation devices are not easily accessible Indicate the particulars of the situation observed PDF code A16-01 A16-02 Pre-described Finding Life jackets/flotation devices not easily accessible when required for the type of flight Insufficient number of life jackets/flotation devices available and required for the type of flight the condition of the life jackets. A life jacket or flotation device without a date does not necessarily constitute a finding. However, if the expiry date (or next inspection date) is overdue, consider as unserviceable. neither the inbound nor the outbound flight or series of flights are over-water flights, then findings should not be raised for this inspection item.

Inspecting Instructions Check for presence, access, sufficient number and serviceability. Note: ICAO does not require life jackets to have an expiration (or next check) date. Operators may employ various systems to monitor Note: ICAO requires the carriage of life jackets/flotation devices only for over-water flights (see the Annex 6 references below). If Note: In the case where spare life jackets have been found to be unserviceable this should reported as General Remark (Cat. G). Standard’s Text Landplanes shall carry the equipment prescribed in 6.5.2.2: a) when flying over water and at a distance of more than 93 km (50 NM) away from the shore, in the case of landplanes operated in accordance with 5.2.9 or 5.2.10; b) when flying en route over water beyond gliding distance from the shore, in the case of all other landplanes; and c) when taking off or landing at an aerodrome where, in the opinion of the State of the Operator, the take-off or approach path is so disposed over water that in the event of a mishap there would be a likelihood of a ditching. The equipment referred to in 6.5.2.1 shall comprise one life jacket or equivalent individual flotation device for each person on board, stowed in a position easily accessible from the seat or berth of the person for whose use it is provided. Note.- "Landplanes" includes amphibians operated as landplanes. Landplanes shall carry the equipment prescribed in 6.5.2.2: a) when flying over water and at a distance of more than 93 km (50 NM) away from the shore, in the case of landplanes operated in accordance with 5.2.9 or 5.2.10; b) when flying en route over water beyond gliding Std. ref. A6-I-6.5.2.1 A6-I-6.5.2.2 A6-I-6.5.2.1 Cat.

2 3

SAFA Ramp Inspection Procedures Guidance material

Inspections Item Title Life jackets/flotation device Std. I I SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A16 Inspection Item A16 A16 V 2.0 Page 85 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text distance from the shore, in the case of all other landplanes; and c) when taking off or landing at an aerodrome where, in the opinion of the State of the Operator, the take-off or approach path is so disposed over water that in the event of a mishap there would be a likelihood of a ditching. The equipment referred to in 6.5.2.1 shall comprise one life jacket or equivalent individual flotation device for each person on board, stowed in a position easily accessible from the seat or berth of the person for whose use it is provided. Note.- "Landplanes" includes amphibians operated as landplanes.

Std. ref. A6-I-6.5.2.2 Cat.

SAFA Ramp Inspection Procedures Guidance material

Std.

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 86 of 217 Instructions for completing the detailed description PDF code A17-01 A17-02 A17-03 Pre-described Finding Pilot harness does not incorporate an automatic restraining device No or unserviceable safety harness for a flight crew seat other than the pilot seats (e.g. large crew configurations) No or unserviceable safety harness for each pilot seat (outside MEL limits) harness is installed.

Inspecting Instructions Check for presence and availability for all flight crew members. Check serviceability (including the automatic restraining device). If unserviceable, check the dispatch conditions in MEL. Note: If the proper functioning of the harness is restricted by the seat covering, consider it unserviceable. Note: If the automatic restraining device is unserviceable, consider the harness as unserviceable. Note: A seat belt only does not meet the ICAO requirements for a safety harness and it should be considered that no safety Standard’s Text 3) A safety harness for each flight crew seat. The safety harness for each pilot seat shall incorporate a device, which will automatically restrain the occupant's torso in the event of rapid deceleration; Note: - Safety harness includes shoulder straps and a seat belt, which may be used independently. 3) A safety harness for each flight crew seat. The safety harness for each pilot seat shall incorporate a device, which will automatically restrain the occupant's torso in the event of rapid deceleration; Note: - Safety harness includes shoulder straps and a seat belt, which may be used independently. 3) A safety harness for each flight crew seat. The safety harness for each pilot seat shall incorporate a device, which will automatically restrain the occupant's torso in the event of rapid deceleration; Note: - Safety harness includes shoulder straps and a seat belt, which may be used independently.

An aeroplane shall be equipped with: An aeroplane shall be equipped with: An aeroplane shall be equipped with: Std. ref. A6-I-6.2.2.c3 A6-I-6.2.2.c3 A6-I-6.2.2.c3 Cat. 2 2 3 Inspections Item Title Harness Std. I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A17 Inspection Item A17 A17 A17 V 2.0 as Page 87 of 217 consider Instructions for completing the detailed description Provide further information as to why the required oxygen equipment is not readily accessible Indicate the particulars of the situation observed overdue, is date) PDF code A18-01 A18-02 Feet 10 000 13 000 25 000 inspection next (or Metres 3 000 4 000 7 600 date expiry the Pre-described Finding Oxygen equipment not readily accessible and required for the type of flight Insufficient number of serviceable quick donning masks available if PSI 10.152642 8.99234 5.453419 However, finding.

a mm Hg 525.043178 465.038243 282.023193 Absolute pressure constitute mBar 700 620 376 employ various systems to monitor the condition of the oxygen masks. An oxygen mask or bottle without a date does not necessarily unserviceable. Remark (Cat. G). follows: hPa/ 700 620 376 Inspecting Instructions Check for presence, access and condition. Check if the oxygen masks allow for a quick donning (rapid fitment). Note: ICAO does not provide a detailed definition of what is a “quick donning” mask. The inspector must therefore act carefully when raising a finding on this matter. Masks that do not meet all the FAA or EU-OPS criteria (place on the face with one hand, less than 5 sec…) must be reported as general remark (G). However, a legitimate finding on the lack of quick donning masks can be raised if the flight crew is unable to prove that : - the masks are serviceable for all the flight crew members, - the masks enable radio communication, - the masks do not represent an hindrance to flight crew members wearing glasses. Check oxygen cylinder pressure. In case of low pressure, check the minimum required according to the OPS manual. Flight Crew can be asked to perform an operational functional check of the combined oxygen and communication system, as this will reveal the status of its integrity. Note: ICAO does not require oxygen masks or oxygen bottles to have an expiration (or next check) date. Operators may Note: In the case where the inspection reveals that the smoke goggles are unserviceable this should be reported as a General Note: Approximate altitude in the Standard Atmosphere corresponding to the value of absolute pressure used in this text is as Standard’s Text Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. All flight crew members of pressurized aeroplanes operating above an altitude where the atmospheric pressure is less than 376 hPa shall have available at the flight duty station a quick- donning type of oxygen mask which will readily Std. ref. A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 A6-I-4.4.5.2 Cat. 3 3 Inspections Item Title Oxygen equipment Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A18 Inspection Item A18 A18 V 2.0 Page 88 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of PDF code A18-03 A18-04 Pre-described Finding Insufficient oxygen and/or serviceable oxygen masks Unserviceable oxygen system Standard’s Text supply oxygen upon demand. A flight to be operated at flight altitudes at which the atmospheric pressure in personnel compartments will be less than 700 hPa shall not be commenced unless sufficient stored breathing oxygen is carried to supply: a) all crew members and 10 per cent of the passengers for any period in excess of 30 minutes that the pressure in compartments occupied by them will be between 700 hPa and 620 hPa; and b) the crew and passengers for any period that the atmospheric pressure in compartments occupied by them will be less than 620 hPa. A flight to be operated with a pressurized aeroplane shall not be commenced unless a sufficient quantity of stored breathing oxygen is carried to supply all the crew members and passengers, as is appropriate to the circumstances of the flight being undertaken, in the event of loss of pressurization, for any period that the atmospheric pressure in any compartment occupied by them would be less than 700 hPa. In addition, when an aeroplane is operated at flight altitudes at which the atmospheric pressure is less than 376 hPa, or which, if operated at flight altitudes at which the atmospheric pressure is more than 376 hPa and cannot descend safely within four minutes to a flight altitude at which the atmospheric pressure is equal to 620 hPa, there shall be no less than a 10-minute supply for the occupants of the passenger compartment. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 700 hPa in personnel compartments shall be equipped with oxygen storage and dispensing apparatus capable of storing and dispensing the oxygen supplies required in Annex 6 Part I Chapter 4.3.8.1. A flight to be operated at flight altitudes at which Std. ref. A6-I-4.3.8.1 A6-I-4.3.8.2 A6-I-6.7.1 A6-I-4.3.8.1 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A18 A18 V 2.0 Page 89 of 217 Instructions for completing the detailed description the situation observed PDF code Pre-described Finding Standard’s Text the atmospheric pressure in personnel compartments will be less than 700 hPa shall not be commenced unless sufficient stored breathing oxygen is carried to supply: a) all crew members and 10 per cent of the passengers for any period in excess of 30 minutes that the pressure in compartments occupied by them will be between 700 hPa and 620 hPa; and b) the crew and passengers for any period that the atmospheric pressure in compartments occupied by them will be less than 620 hPa. A flight to be operated with a pressurized aeroplane shall not be commenced unless a sufficient quantity of stored breathing oxygen is carried to supply all the crew members and passengers, as is appropriate to the circumstances of the flight being undertaken, in the event of loss of pressurization, for any period that the atmospheric pressure in any compartment occupied by them would be less than 700 hPa. In addition, when an aeroplane is operated at flight altitudes at which the atmospheric pressure is less than 376 hPa, or which, if operated at flight altitudes at which the atmospheric pressure is more than 376 hPa and cannot descend safely within four minutes to a flight altitude at which the atmospheric pressure is equal to 620 hPa, there shall be no less than a 10-minute supply for the occupants of the passenger compartment. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 700 hPa in personnel compartments shall be equipped with oxygen storage and dispensing apparatus capable of storing and dispensing the oxygen supplies required in Annex 6 Part I Chapter 4.3.8.1.

Std. ref. A6-I-4.3.8.2 A6-I-6.7.1 Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 90 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A19-01 A19-02 A19-03 Pre-described Finding Serviceable electric torch for both pilots but not for other flight crew members during night operation Electric torches not readily available during night operation Insufficient number of serviceable electric torches for all pilots during night operation into the night, and aircraft departed at night and arrived in daytime. When inspecting daylight only flights, the absence or unserviceability of any electric torch does not constitute a finding. This should however be reported as General Remark (Cat. G). flight crew from their normal positions. This should however be reported as General Remark (Cat. G).

Inspecting Instructions Check that appropriate electric torches are readily available at all crew member stations. Check their condition, serviceability and access. Please note that flights departing in daylight, but extending into the night, shall meet this requirement. Note: Only aircraft operated at night require electric torches for the crew. This includes flights departing in daylight but extending Note: If the proper functioning of the torch is significantly affected as a result of weak batteries, consider it unserviceable. Note: If only personal torches are available this should not be considered as a finding provided they are readily available to the Standard’s Text Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. All aeroplanes, when operated at night shall be equipped with: f) An electric torch for each crew member station. All aeroplanes, when operated at night shall be equipped with: f) An electric torch for each crew member station. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. All aeroplanes, when operated at night shall be equipped with: f) An electric torch for each crew member station. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked.

Std. ref. A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 A6-I-6.10f A6-I-6.10f A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 A6-I-6.10f A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 Cat. 1 3 3 Inspections Item Title Flash light Std. I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A19 Inspection Item A19 A19 A19 V 2.0 ICAO the Page 91 of 217 meeting not although authority), issuing the by (certified licences crew flight of copies Certified as finding. However, in the case when there is indicated a level lower than level 4 this should be considered a finding. The same is for the expiry date of level 4 and 5 endorsements: they are not required to be mentioned, but if they are mentioned and expired, a finding can be raised. A36-11, can be found on the ICAO FSIX web-page: http://www.icao.int/fsix/lp.cfm . implementation plans for language proficiency. Therefore, for those States no cat. 3 findings should be raised. Language proficiency findings on licences issued by States which did not file a corrective action plan shall be categorised as cat. 3 findings. in communicating in English, this should be reported as a General Remark. ways such as a suitably titled separate certificate, a statement on the licence, a national regulation stipulating that the Medical Assessment is an integral part of the licence, etc. . requirements, should not be accepted, unless it is clear that the original is with the issuer for the purpose of renewal, etc. – in this cases a finding should not be raised. this shall be used. However, if before departure the appropriate evidence is received that the crew member is indeed holding an appropriate and valid licence, but simply did not carry this licence, the category 1 finding “Flight crew holding appropriate Licence but not carried on board at the time of the inspection” should be raised. If such evidence is not provided before departure, the category 3 finding “Flight crew without appropriate licence” requiring corrective carried on board at the time of the inspection, apply the procedure described in Chapter 4.3 above. Certificate of flight crew member is not carried on board at the time of the inspection, apply the procedure described in Chapter 4.3 above.

Inspecting Instructions Check for presence and validity of crew licences and appropriate ratings. If the licence of a flight crew member is not Check for presence and validity of the Medical Certificate and, if appropriate, for the privileges exercised. If the Medical Check if form and content (including English translation) is in compliance with ICAO Annex 1. Check if the flight crew members are meeting the age requirements (pilots over 60 years). In case of licences issued by an authority other than the one of the State of Registry, check the validation of the licence. Check for spare correcting spectacles (in case a flight crew member is required to wear corrective lenses). Check for endorsement of English language proficiency (ELP) in the licence. Note: The explicit mentioning of the ELP Level in the licence is not mandatory and such a case should not be considered Note: Information about the countries which have filed a corrective action plan with ICAO, as requested by the Resolution Note: ICAO urges Contracting States to take a flexible approach towards States which made progress with regard to their Note: If during a ramp inspection a pilot is found to be properly endorsed with the required ELP, but has obvious difficulties Note: The appropriate Class 1, Class 2 or Class 3 Medical Assessment can be issued to the licence holder in several Note: Note: If the licence of a flight crew member was not found on board during the inspection, the Category 3 PDF reflecting Inspections Item Title Flight Crew Licence

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 V 2.0 link: Page 92 of 217 following Instructions for completing the detailed description Indicate what document (licence, medical certificate) the at PDF code A20-01 available is document This Pre-described Finding Form and/or content not in compliance with ICAO standard (licence, medical certificate) States.

European several amongst actions before the flight is authorised. Under no circumstances, a flight crew member should be permitted to perform flying duties without receiving confirmation that s/he has been issued an appropriate and valid licence). licences http://easa.europa.eu/approvals-and-standardisation/mutual-recognition.php . Moreover, licences issued under Part FCL enjoy automatic mutual recognition in all EASA states (27 EU Member States + Iceland, Norway, Switzerland) (e.g. a person holding a licence issued by one of the EASA states can exercise his/her privileges on any aircraft registered in any EASA state without any additional need for validation).

Note: Inspectors have to take into account, when inspecting European flight crew licences, the mutual recognition of those Standard’s Text The following details shall appear on the licence: I) Name of State (in bold type); II) Title of licence (in very bold type); III) Serial number of the licence, in Arabic numerals, given by the authority issuing the licence; IV) Name of holder in full (in Roman alphabet also if script of national language is other than Roman); IVa) Date of birth; V) Address of holder if desired by the State; VI) Nationality of holder; VII) Signature of holder; VIII) Authority and, where necessary, conditions under which the licence is issued; IX) Certification concerning validity and authorization for holder to exercise privileges appropriate to licence; X) Signature of officer issuing the licence and the date of such issue; XI) Seal or stamp of authority issuing the licence; XII) Ratings, e.g. category, class, type of aircraft, airframe, aerodrome control, etc.; XIII) Remarks, i.e. special endorsements relating to limitations and endorsements for privileges, including from 5 March 2008 an endorsement of language proficiency, and other information required in pursuance to Article 39 of the Chicago Convention; XIV) Any other details desired by the State issuing the licence. Three classes of Medical Assessment shall be established as follows: Std. ref. A1-5.1.1.2 A1-6.1.1a,b Cat. 2 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 V 2.0 Page 93 of 217 Instructions for completing the detailed description Indicate expiry date, the assignment of the involved pilot (captain, co-pilot) and / or ELP level, if available PDF code A20-02 A20-03 A20-04 Pre-described Finding No crewmember holds a valid R/T licence/rating No declaration of licence differences compared to ICAO standards ELP endorsment expired Standard’s Text a) Class 1 Medical Assessment; applies to applicants for, and holders of: - commercial pilot licences - aeroplane, airship, helicopter and powered-lift - multi-crew pilot licences - aeroplane - airline transport pilot licences - aeroplane, helicopter and powered-lift b) Class 2 Medical Assessment; applies to applicants for, and holders of: - flight navigator licences - flight engineer licences - private pilot licences - aeroplane, airship, helicopter and powered-lift - glider pilot licences - free balloon pilot licences The flight crew shall include at least one member who holds a valid licence, issued or rendered valid by the State of Registry, authorizing operation of the type of radio transmitting equipment to be used. Endorsement of certificates and licences b) Any person holding a licence who does not satisfy in full the conditions laid down in the international standard relating to the class of licence or certificate which he holds shall have endorsed on or attached to his licence a complete enumeration of the particulars in which he does not satisfy such conditions. As of 5 March 2008, aeroplane, airship, helicopter and powered-lift pilots, air traffic controllers and aeronautical station operators shall demonstrate the ability to speak and understand the language used for radiotelephony communications to the level specified in the language proficiency requirements in Appendix 1. General: To meet the language proficiency requirements contained in Chapter 1, Section 1.2.9, an applicant for a licence or a licence holder shall demonstrate, in a manner acceptable to the licensing authority, compliance with Std. ref. A6-I-9.1.2 CC-39b A1-1.2.9.4 A1-APP 1 Cat. 3 2 2 Std. I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 A20 A20 V 2.0 Page 94 of 217 Instructions for completing the detailed description Indicate the assignment of the involved pilot (captain, co-pilot) and / or ELP level, if available PDF code A20-05 Pre-described Finding No endorsement of the required English language proficiency and / or level lower than Level 4 (but corrective action plan filed by the licensing State to ICAO).

Standard’s Text the holistic descriptors at Section 2 and with the ICAO Operational Level (Level 4) of the ICAO Language Proficiency Rating Scale in Attachment A. The following details shall appear on the licence: I) Name of State (in bold type); II) Title of licence (in very bold type); III) Serial number of the licence, in Arabic numerals, given by the authority issuing the licence; IV) Name of holder in full (in Roman alphabet also if script of national language is other than Roman); IVa) Date of birth; V) Address of holder if desired by the State; VI) Nationality of holder; VII) Signature of holder; VIII) Authority and, where necessary, conditions under which the licence is issued; IX) Certification concerning validity and authorization for holder to exercise privileges appropriate to licence; X) Signature of officer issuing the licence and the date of such issue; XI) Seal or stamp of authority issuing the licence; XII) Ratings, e.g. category, class, type of aircraft, airframe, aerodrome control, etc.; XIII) Remarks, i.e. special endorsements relating to limitations and endorsements for privileges, including from 5 March 2008 an endorsement of language proficiency, and other information required in pursuance to Article 39 of the Chicago Convention; XIV) Any other details desired by the State issuing the licence. As of 5 March 2008, aeroplane, airship, helicopter and powered-lift pilots, air traffic controllers and aeronautical station operators shall demonstrate the ability to speak and understand the language used for radiotelephony communications to the level specified in the language proficiency requirements in Appendix 1.

Std. ref. A1-5.1.1.2 A1-1.2.9.4 Cat. 2 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 V 2.0 Page 95 of 217 Instructions for completing the detailed description Indicate the assignment of the involved pilot (captain, PDF code A20-06 Pre-described Finding No endorsement of the required English language proficiency and / or level lower than Level 4 Standard’s Text General: To meet the language proficiency requirements contained in Chapter 1, Section 1.2.9, an applicant for a licence or a licence holder shall demonstrate, in a manner acceptable to the licensing authority, compliance with the holistic descriptors at Section 2 and with the ICAO Operational Level (Level 4) of the ICAO Language Proficiency Rating Scale in Attachment A. The following details shall appear on the licence: I) Name of State (in bold type); II) Title of licence (in very bold type); III) Serial number of the licence, in Arabic numerals, given by the authority issuing the licence; IV) Name of holder in full (in Roman alphabet also if script of national language is other than Roman); IVa) Date of birth; V) Address of holder if desired by the State; VI) Nationality of holder; VII) Signature of holder; VIII) Authority and, where necessary, conditions under which the licence is issued; IX) Certification concerning validity and authorization for holder to exercise privileges appropriate to licence; X) Signature of officer issuing the licence and the date of such issue; XI) Seal or stamp of authority issuing the licence; XII) Ratings, e.g. category, class, type of aircraft, airframe, aerodrome control, etc.; XIII) Remarks, i.e. special endorsements relating to limitations and endorsements for privileges, including from 5 March 2008 an endorsement of language proficiency, and other information required in pursuance to Article 39 of the Chicago Convention; XIV) Any other details desired by the State issuing the licence. As of 5 March 2008, aeroplane, airship, helicopter and powered-lift pilots, air traffic controllers and aeronautical station operators shall demonstrate the Std. ref. A1-APP 1 A1-5.1.1.2 A1-1.2.9.4 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 V 2.0 Page 96 of 217 Instructions for completing the detailed description co-pilot) and / or ELP level, if available PDF code Pre-described Finding (and no corrective action plan filed by the licensing State to ICAO).

Standard’s Text ability to speak and understand the language used for radiotelephony communications to the level specified in the language proficiency requirements in Appendix 1. General: To meet the language proficiency requirements contained in Chapter 1, Section 1.2.9, an applicant for a licence or a licence holder shall demonstrate, in a manner acceptable to the licensing authority, compliance with the holistic descriptors at Section 2 and with the ICAO Operational Level (Level 4) of the ICAO Language Proficiency Rating Scale in Attachment A. The following details shall appear on the licence: I) Name of State (in bold type); II) Title of licence (in very bold type); III) Serial number of the licence, in Arabic numerals, given by the authority issuing the licence; IV) Name of holder in full (in Roman alphabet also if script of national language is other than Roman); IVa) Date of birth; V) Address of holder if desired by the State; VI) Nationality of holder; VII) Signature of holder; VIII) Authority and, where necessary, conditions under which the licence is issued; IX) Certification concerning validity and authorization for holder to exercise privileges appropriate to licence; X) Signature of officer issuing the licence and the date of such issue; XI) Seal or stamp of authority issuing the licence; XII) Ratings, e.g. category, class, type of aircraft, airframe, aerodrome control, etc.; XIII) Remarks, i.e. special endorsements relating to limitations and endorsements for privileges, including from 5 March 2008 an endorsement of language proficiency, and other information required in pursuance to Article 39 of the Chicago Convention; XIV) Any other details desired by the State issuing the Std. ref. A1-APP 1 A1-5.1.1.2 Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 97 of 217 Instructions for completing the detailed description Indicate the assignment of the involved pilot (captain, co-pilot) and / or ELP level, if available PDF code A20-07 Pre-described Finding No endorsement of the required English language proficiency and / or level lower than Level 4 (whilst the licensing State filed compliance to ICAO) Standard’s Text licence. As of 5 March 2008, aeroplane, airship, helicopter and powered-lift pilots, air traffic controllers and aeronautical station operators shall demonstrate the ability to speak and understand the language used for radiotelephony communications to the level specified in the language proficiency requirements in Appendix 1. General: To meet the language proficiency requirements contained in Chapter 1, Section 1.2.9, an applicant for a licence or a licence holder shall demonstrate, in a manner acceptable to the licensing authority, compliance with the holistic descriptors at Section 2 and with the ICAO Operational Level (Level 4) of the ICAO Language Proficiency Rating Scale in Attachment A. The following details shall appear on the licence: I) Name of State (in bold type); II) Title of licence (in very bold type); III) Serial number of the licence, in Arabic numerals, given by the authority issuing the licence; IV) Name of holder in full (in Roman alphabet also if script of national language is other than Roman); IVa) Date of birth; V) Address of holder if desired by the State; VI) Nationality of holder; VII) Signature of holder; VIII) Authority and, where necessary, conditions under which the licence is issued; IX) Certification concerning validity and authorization for holder to exercise privileges appropriate to licence; X) Signature of officer issuing the licence and the date of such issue; XI) Seal or stamp of authority issuing the licence; XII) Ratings, e.g. category, class, type of aircraft, airframe, aerodrome control, etc.; XIII) Remarks, i.e. special endorsements relating to limitations and endorsements for privileges, including Std. ref. A1-1.2.9.4 A1-APP 1 A1-5.1.1.2 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 V 2.0 Page 98 of 217 Instructions for completing the detailed description PDF code A20-08 A20-09 Pre-described Finding No English translation of ICAO required items of the licence No mention of ICAO medical class Standard’s Text from 5 March 2008 an endorsement of language proficiency, and other information required in pursuance to Article 39 of the Chicago Convention; XIV) Any other details desired by the State issuing the licence. When licences are issued in a language other than English, the licence shall include an English translation of at least items I), II), VI), IX), XII), XIII) and XIV). When provided in a language other than English, authorizations issued in accordance with 1.2.2.1 shall include an English translation of the name of the State issuing the authorization, the limit of validity of the authorization and any restriction or limitation that may be established. The following details shall appear on the licence: I) Name of State (in bold type); II) Title of licence (in very bold type); III) Serial number of the licence, in Arabic numerals, given by the authority issuing the licence; IV) Name of holder in full (in Roman alphabet also if script of national language is other than Roman); IVa) Date of birth; V) Address of holder if desired by the State; VI) Nationality of holder; VII) Signature of holder; VIII) Authority and, where necessary, conditions under which the licence is issued; IX) Certification concerning validity and authorization for holder to exercise privileges appropriate to licence; X) Signature of officer issuing the licence and the date of such issue; XI) Seal or stamp of authority issuing the licence; XII) Ratings, e.g. category, class, type of aircraft, airframe, aerodrome control, etc.; XIII) Remarks, i.e. special endorsements relating to limitations and endorsements for privileges, including from 5 March 2008 an endorsement of language proficiency, and other information required in pursuance to Article 39 of the Chicago Convention; Std. ref. A1-5.1.3 A1-5.1.1.2 Cat. 2 2 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 A20 V 2.0 Page 99 of 217 Instructions for completing the detailed description PDF code A20-10 Pre-described Finding No proper validation issued by the State of registry Standard’s Text XIV) Any other details desired by the State issuing the licence. Three classes of Medical Assessment shall be established as follows: a) Class 1 Medical Assessment; applies to applicants for, and holders of: - commercial pilot licences - aeroplane, airship, helicopter and powered-lift - multi-crew pilot licences - aeroplane - airline transport pilot licences - aeroplane, helicopter and powered-lift b) Class 2 Medical Assessment; applies to applicants for, and holders of: - flight navigator licences - flight engineer licences - private pilot licences - aeroplane, airship, helicopter and powered-lift - glider pilot licences - free balloon pilot licences A person shall not act as a flight crew member of an aircraft unless a valid licence is held showing compliance with the specifications of this Annex and appropriate to the duties to be performed by that person. The licence shall have been issued by the State of Registry of that aircraft or by any other Contracting State and rendered valid by the State of Registry of that aircraft. Note.— Article 29 of the Convention on International Civil Aviation requires that the flight crew members carry their appropriate licences on board every aircraft engaged in international air navigation. When a Contracting State renders valid a licence issued by another Contracting State, as an alternative to the issuance of its own licence, it shall establish validity by suitable authorization to be carried with the former licence accepting it as the equivalent of the latter. When a State limits the authorization to specific privileges, the authorization shall specify the privileges of the licence which are to be accepted as Std. ref. A1-6.1.1a,b A1-1.2.1 A1-1.2.2.1 Cat. 2 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 V 2.0 Page 100 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code A20-11 Pre-described Finding Spare correcting spectacles not available (for multi-pilot operations) Standard’s Text its equivalent. The validity of the authorization shall not extend beyond the period of validity of the licence. The authorization ceases to be valid if the licence upon which it was issued is revoked or suspended. Note.- This provision is not intended to preclude the State that issued the licence from extending, by a suitable notification, the period of validity of the licence without necessarily requiring either the physical return of the licence or the appearance of the licence holder before the Authorities of that State. Documents carried in aircraft Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention. c) The appropriate licences for each member of the crew. Licences of personnel a) The pilot of every aircraft and the other members of the operating crew of every aircraft engaged in international navigation shall be provided with certificates of competency and licences issued or rendered valid by the State in which the aircraft is registered. Validity of endorsed certificates and licences No aircraft or personnel having certificates or licences so endorsed shall participate in international navigation, except with the permission of the State or States whose territory is entered. The registration or use of any such aircraft, or of any certificated aircraft part, in any State other than that in which it was originally certificated shall be at the discretion of the State into which the aircraft or part is imported. Distant visual acuity with or without correction shall be 6/9 or better in each eye separately, and binocular visual acuity shall be 6/6 or better. No limits apply to uncorrected visual acuity. Where this standard of visual acuity can be obtained only with correcting lenses, the applicant may be assessed as fit provided Std. ref. CC-29c CC-32a CC-40 A1-6.3.3.2 Cat. 2 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 V 2.0 Page 101 of 217 Instructions for completing the detailed description PDF code A20-12 A20-13 Pre-described Finding Both pilots older than 60 years Flight crew member without appropriate licence Standard’s Text that: a) such correcting lenses are worn during the exercise of the privileges of the licence or rating applied for or held; and b) in addition, a pair of suitable correcting spectacles is kept readily available during the exercise of the privileges of the applicant's licence. Note 1.- 6.3.3.2 b) is the subject of Standards in Annex 6, Part I. Note 2.- An applicant accepted as meeting these provisions is deemed to continue to do so unless there is reason to suspect otherwise, in which case an ophthalmic report is required at the discretion of the Licensing Authority. Both uncorrected and corrected visual acuity are normally measured and recorded at each re-examination. Conditions which indicate a need to obtain an ophthalmic report include: a substantial decrease in the uncorrected visual acuity, any decrease in best corrected visual acuity, and the occurrence of eye disease, eye injury or eye surgery. A Contracting State, having issued pilot licences, shall not permit the holders thereof to act as pilot-in- command of an aircraft engaged in international commercial air transport operations if the licence holders have attained their 60th birthday or, in the case of operations with more than one pilot where the other pilot is younger than 60 years of age, their 65th birthday. A person shall not act as a flight crew member of an aircraft unless a valid licence is held showing compliance with the specifications of this Annex and appropriate to the duties to be performed by that person. The licence shall have been issued by the State of Registry of that aircraft or by any other Contracting State and rendered valid by the State of Registry of that aircraft. Note.— Article 29 of the Convention on International Civil Aviation requires that the flight crew members carry their appropriate licences on board every aircraft Std. ref. A1-2.1.10.1 A1-1.2.1 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 A20 V 2.0 Page 102 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text engaged in international air navigation When a Contracting State renders valid a licence issued by another Contracting State, as an alternative to the issuance of its own licence, it shall establish validity by suitable authorization to be carried with the former licence accepting it as the equivalent of the latter. When a State limits the authorization to specific privileges, the authorization shall specify the privileges of the licence which are to be accepted as its equivalent. The validity of the authorization shall not extend beyond the period of validity of the licence. The authorization ceases to be valid if the licence upon which it was issued is revoked or suspended. Note.- This provision is not intended to preclude the State that issued the licence from extending, by a suitable notification, the period of validity of the licence without necessarily requiring either the physical return of the licence or the appearance of the licence holder before the Authorities of that State. Documents carried in aircraft Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention. c) The appropriate licences for each member of the crew. Licences of personnel a) The pilot of every aircraft and the other members of the operating crew of every aircraft engaged in international navigation shall be provided with certificates of competency and licences issued or rendered valid by the State in which the aircraft is registered. Validity of endorsed certificates and licences No aircraft or personnel having certificates or licences so endorsed shall participate in international navigation, except with the permission of the State or States whose territory is entered. The registration or Std. ref. A1-1.2.2.1 CC-29c CC-32a CC-40 Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 103 of 217 Instructions for completing the detailed description PDF code A20-14 Pre-described Finding Medical certificate invalid for the privileges being exercised Standard’s Text use of any such aircraft, or of any certificated aircraft part, in any State other than that in which it was originally certificated shall be at the discretion of the State into which the aircraft or part is imported. Except as provided in 1.2.5.2.1, 1.2.5.2.2, 1.2.5.2.3, 1.2.5.2.4, 1.2.5.2.5 and 1.2.5.2.6, a Medical Assessment issued in accordance with 1.2.4.6 and 1.2.4.7 shall be valid from the date of the medical examination for a period not greater than: 60 months for the private pilot licence - aeroplane, airship, helicopter and powered-lift; 12 months for the commercial pilot licence - aeroplane, airship, helicopter and powered-lift; 12 months for the multi-crew pilot licence - aeroplane; 12 months for the airline transport pilot licence - aeroplane, helicopter and powered-lift; 60 months for the glider pilot licence; 60 months for the free balloon pilot licence; 12 months for the flight navigator licence; 12 months for the flight engineer licence; 48 months for the air traffic controller licence. Note 1.- The periods of validity listed above may be extended by up to 45 days in accordance with 1.2.4.3.1. Note 2.- When calculated in accordance with 1.2.5.2 and its sub-paragraphs, the period of validity will, for the last month counted, include the day that has the same calendar number as the date of the medical examination or, if that month has no day with that number, the last day of that month. When the holders of airline transport pilot licences - aeroplane, helicopter and powered-lift, and commercial pilot licences - aeroplane, airship, helicopter and powered-lift, who are engaged in single-crew commercial air transport operations carrying passengers, have passed their 40th birthday, the period of validity specified in 1.2.5.2 shall be reduced to six months. When the holders of airline transport pilot licences - Std. ref. A1-1.2.5.2 A1-1.2.5.2.2 A1-1.2.5.2.3 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 V 2.0 Page 104 of 217 Instructions for completing the detailed description PDF code A20-15 Pre-described Finding No appropriate type rating on flight crew member’s licence Standard’s Text aeroplane, helicopter and powered-lift, commercial pilot licences - aeroplane, airship, helicopter and powered lift, and multi-crew pilot licences - aeroplane, who are engaged in commercial air transport operations, have passed their 60th birthday, the period of validity specified in 1.2.5.2 shall be reduced to six months. A person shall not act as a flight crew member of an aircraft unless a valid licence is held showing compliance with the specifications of this Annex and appropriate to the duties to be performed by that person. The licence shall have been issued by the State of Registry of that aircraft or by any other Contracting State and rendered valid by the State of Registry of that aircraft. Note.— Article 29 of the Convention on International Civil Aviation requires that the flight crew members carry their appropriate licences on board every aircraft engaged in international air navigation. When a Contracting State renders valid a licence issued by another Contracting State, as an alternative to the issuance of its own licence, it shall establish validity by suitable authorization to be carried with the former licence accepting it as the equivalent of the latter. When a State limits the authorization to specific privileges, the authorization shall specify the privileges of the licence which are to be accepted as its equivalent. The validity of the authorization shall not extend beyond the period of validity of the licence. The authorization ceases to be valid if the licence upon which it was issued is revoked or suspended. Note.- This provision is not intended to preclude the State that issued the licence from extending, by a suitable notification, the period of validity of the licence without necessarily requiring either the physical return of the licence or the appearance of the Std. ref. A1-1.2.1 A1-1.2.2.1 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 V 2.0 Page 105 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code A20-16 Pre-described Finding No correcting lenses available when required Standard’s Text licence holder before the Authorities of that State. Documents carried in aircraft Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention. c) The appropriate licences for each member of the crew. Licences of personnel a) The pilot of every aircraft and the other members of the operating crew of every aircraft engaged in international navigation shall be provided with certificates of competency and licences issued or rendered valid by the State in which the aircraft is registered. Validity of endorsed certificates and Licences No aircraft or personnel having certificates or licences so endorsed shall participate in international navigation, except with the permission of the State or States whose territory is entered. The registration or use of any such aircraft, or of any certificated aircraft part, in any State other than that in which it was originally certificated shall be at the discretion of the State into which the aircraft or part is imported. Distant visual acuity with or without correction shall be 6/9 or better in each eye separately, and binocular visual acuity shall be 6/6 or better. No limits apply to uncorrected visual acuity. Where this standard of visual acuity can be obtained only with correcting lenses, the applicant may be assessed as fit provided that: a) such correcting lenses are worn during the exercise of the privileges of the licence or rating applied for or held; and b) in addition, a pair of suitable correcting spectacles is kept readily available during the exercise of the privileges of the applicant's licence. Note 1.- 6.3.3.2 b) is the subject of Standards in Std. ref. CC-29c CC-32a CC-40 A1-6.3.3.2 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 V 2.0 Page 106 of 217 Instructions for completing the detailed description PDF code A20-17 A20-18 Pre-described Finding PIC over 60 in single pilot operations PIC over 65 in multipilot operations Standard’s Text Annex 6, Part I. Note 2.- An applicant accepted as meeting these provisions is deemed to continue to do so unless there is reason to suspect otherwise, in which case an ophthalmic report is required at the discretion of the Licensing Authority. Both uncorrected and corrected visual acuity are normally measured and recorded at each re-examination. Conditions which indicate a need to obtain an ophthalmic report include: a substantial decrease in the uncorrected visual acuity, any decrease in best corrected visual acuity, and the occurrence of eye disease, eye injury or eye surgery. Applicants may use contact lenses to meet this requirement provided that: a) the lenses are monofocal and non-tinted; b) the lenses are well tolerated; and c) a pair of suitable correcting spectacles is kept readily available during the exercise of the licence privileges. Note.- Applicants who use contact lenses may not need to have their uncorrected visual acuity measured at each re-examination provided the history of their contact lens prescription is known. A Contracting State, having issued pilot licences, shall not permit the holders thereof to act as pilot-in- command of an aircraft engaged in international commercial air transport operations if the licence holders have attained their 60th birthday or, in the case of operations with more than one pilot where the other pilot is younger than 60 years of age, their 65th birthday. A Contracting State, having issued pilot licences, shall not permit the holders thereof to act as pilot-in- command of an aircraft engaged in international commercial air transport operations if the licence holders have attained their 60th birthday or, in the case of operations with more than one pilot where the other pilot is younger than 60 years of age, their 65th Std. ref. A1-6.3.3.2.1 A1-2.1.10.1 A1-2.1.10.1 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 A20 V 2.0 Page 107 of 217 Instructions for completing the detailed description PDF code A20-19 A20-20 Pre-described Finding Spare correcting spectacles not available (for single pilot operations) A valid and appropriate Flight crew licence was issued but not carried on board at the time of the inspection.

Standard’s Text birthday. Distant visual acuity with or without correction shall be 6/9 or better in each eye separately, and binocular visual acuity shall be 6/6 or better. No limits apply to uncorrected visual acuity. Where this standard of visual acuity can be obtained only with correcting lenses, the applicant may be assessed as fit provided that: a) such correcting lenses are worn during the exercise of the privileges of the licence or rating applied for or held; and b) in addition, a pair of suitable correcting spectacles is kept readily available during the exercise of the privileges of the applicant's licence. Note 1.- 6.3.3.2 b) is the subject of Standards in Annex 6, Part I. Note 2.- An applicant accepted as meeting these provisions is deemed to continue to do so unless there is reason to suspect otherwise, in which case an ophthalmic report is required at the discretion of the Licensing Authority. Both uncorrected and corrected visual acuity are normally measured and recorded at each re-examination. Conditions which indicate a need to obtain an ophthalmic report include: a substantial decrease in the uncorrected visual acuity, any decrease in best corrected visual acuity, and the occurrence of eye disease, eye injury or eye surgery. A person shall not act as a flight crew member of an aircraft unless a valid licence is held showing compliance with the specifications of this Annex and appropriate to the duties to be performed by that person. The licence shall have been issued by the State of Registry of that aircraft or by any other Contracting State and rendered valid by the State of Registry of that aircraft. Note.— Article 29 of the Convention on International Civil Aviation requires that the flight crew members carry their appropriate licences on board every aircraft engaged in international air navigation Std. ref. A1-6.3.3.2 A1-1.2.1 Cat. 3 1 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A20 A20 V 2.0 Page 108 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text When a Contracting State renders valid a licence issued by another Contracting State, as an alternative to the issuance of its own licence, it shall establish validity by suitable authorization to be carried with the former licence accepting it as the equivalent of the latter. When a State limits the authorization to specific privileges, the authorization shall specify the privileges of the licence which are to be accepted as its equivalent. The validity of the authorization shall not extend beyond the period of validity of the licence. The authorization ceases to be valid if the licence upon which it was issued is revoked or suspended. Note.- This provision is not intended to preclude the State that issued the licence from extending, by a suitable notification, the period of validity of the licence without necessarily requiring either the physical return of the licence or the appearance of the licence holder before the Authorities of that State. Documents carried in aircraft Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention. c) The appropriate licences for each member of the crew. Licences of personnel a) The pilot of every aircraft and the other members of the operating crew of every aircraft engaged in international navigation shall be provided with certificates of competency and licences issued or rendered valid by the State in which the aircraft is registered. Validity of endorsed certificates and licences No aircraft or personnel having certificates or licences so endorsed shall participate in international navigation, except with the permission of the State or States whose territory is entered. The registration or use of any such aircraft, or of any certificated aircraft part, in any State other than that in which it was Std. ref. A1-1.2.2.1 CC-29c CC-32a CC-40 Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 109 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text originally certificated shall be at the discretion of the State into which the aircraft or part is imported.

Std. ref.

Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 110 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A21-01 A21-02 Pre-described Finding Inconsistent data entered into the Journey Log Book Flight details not recorded in a journey logbook or General Declaration information listed in Annex 6, Part I, 11.4.1).

Inspecting Instructions Check for presence. Note: In some cases the Journey Log Book may be replaced by a document called General Declaration (provided it contains the Check if content of Journey logbook/General Declaration complies with the requirement and if properly filled in. Standard’s Text The pilot-in-command shall be responsible for the journey log book or the general declaration containing the information listed in 11.4.1. Note.- By virtue of Resolution A10-36 of the Tenth Session of the Assembly (Caracas, June-July 1956) "the General Declaration, [described in Annex 9] when prepared so as to contain all the information required by Article 34 [of the Convention on International Civil Aviation] with respect to the journey log book, may be considered by Contracting States to be an acceptable form of journey log book". There shall be maintained in respect of every aircraft engaged in international navigation a journey log book in which shall be entered particulars of the aircraft, its crew and of each journey, in such form as may be prescribed from time to time pursuant to this Convention. journey log book or the general declaration containing the information listed in 11.4.1. Note.- By virtue of Resolution A10-36 of the Tenth Session of the Assembly (Caracas, June-July 1956) "the General Declaration, [described in Annex 9] when prepared so as to contain all the information required by Article 34 [of the Convention on International Civil Aviation] with respect to the journey log book, may be considered by Contracting States to be an acceptable form of journey log book". There shall be maintained in respect of every aircraft engaged in international navigation a journey log book in which shall be entered particulars of the The pilot-in-command shall be responsible for the Std. ref. A6-I-4.5.5 CC-34 A6-I-4.5.5 CC-34 Cat. 1 2 Inspections Item Title Journey Log Book, or equivalent Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A21 Inspection Item A21 A21 V 2.0 Page 111 of 217 Instructions for completing the detailed description PDF code A21-03 Pre-described Finding Journey logbook or General Declaration not on board Standard’s Text aircraft, its crew and of each journey, in such form as may be prescribed from time to time pursuant to this Convention. Every aircraft of a contracting State, engaged in international navigation, shall carry the following documents in conformity with the conditions prescribed in this Convention. d) Its journey log book; Std. ref. CC-29d Cat. 2 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A21 V 2.0 Page 112 of 217 Instructions for completing the detailed description PDF code A22-01 Pre-described Finding PIC did not certify that s/he is satisfied that a maintenance release has been issued how the PIC satisfied himself that the aeroplane is airworthy and the maintenance release has been issued.

Inspecting Instructions Check that the PIC certified that a maintenance release has been issued (usually by accepting the aeroplane). Note: A Maintenance Release following scheduled maintenance is not required to be carried on board the aeroplane. Check Standard’s Text A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in- command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; Std. ref. A6-I-4.3.1(a)(c) Cat. 3 Inspections Item Title Maintenance Release Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A22 Inspection Item A22 V 2.0 Page 113 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A23-01 A23-02 Pre-described Finding Defect deferred with a wrong MEL/CDL reference Item closed but not reported as such in the deferred defect list / crew has to be able to understand the entries in the ATLB.

Inspecting Instructions Check for any deferred defects (specify in the report where necessary). Check that all defects (minor, major, dents, damages etc.) have been properly reported and assessed. Check if the associated maintenance actions have been properly reported, e.g. description of the action, AMM/SRM references. When defect deferments include time limits check that the open deferred defects remain within those stated. Where applicable, check compliance with the aircraft MEL. Check that the rectification intervals stated in the ATLB do not exceed those required by the MEL. Note: There is no requirement for the ATLB (Technical Log) to contain entries in a specific language. In any case the flight Standard’s Text A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; The pilot-in-command shall be responsible for reporting all known or suspected defects in the aeroplane, to the operator, at the termination of the flight. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the Airworthiness requirements applicable in the State of Registry. A flight shall not be commenced until flight preparation Std. ref. A6-I-4.3.1(a)(c) A6-I-4.5.4 A6-I-6.1.3 A6-I-4.3.1(a)(c) Cat. 1 1 Inspections Item Title Defect notification and rectification (incl. Tech Log) Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A23 Inspection Item A23 A23 V 2.0 Page 114 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code A23-03 Pre-described Finding hold item list Maintenance action not properly reported Standard’s Text forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; The pilot-in-command shall be responsible for reporting all known or suspected defects in the aeroplane, to the operator, at the termination of the flight. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the Airworthiness requirements applicable in the State of Registry. 8.4.1 An operator shall ensure that the following records are kept for the periods mentioned in 8.4.2: a) the total time in service (hours, calendar time and cycles, as appropriate) of the aeroplane and all life-limited components; b) the current status of compliance with all mandatory continuing airworthiness information; c) appropriate details of modifications and repairs; d) the time in service (hours, calendar time and cycles, as appropriate) since the last overhaul of the aeroplane or its components subject to a mandatory overhaul life; Std. ref. A6-I-4.5.4 A6-I-6.1.3 A6-I-8.4 Cat. 2 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A23 V 2.0 Page 115 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text e) the current status of the aeroplane’s compliance with the maintenance programme; and f) the detailed maintenance records to show that all requirements for the signing of a maintenance release have been met. 8.4.2 The records in 8.4.1 a) to e) shall be kept for a minimum period of 90 days after the unit to which they refer has been permanently withdrawn from service, and the records in 8.4.1 f) for a minimum period of one year after the signing of the maintenance release. 8.4.3 In the event of a temporary change of operator, the records shall be made available 8.5.1 The operator of an aeroplane over 5 700 kg maximum certificated take-off mass shall monitor and assess maintenance and operational experience with respect to continuing airworthiness and provide the information as prescribed by the State of Registry and report through the system specified in Annex 8, Part II, 4.2.3 f) and 4.2.4. 8.5.2 The operator of an aeroplane over 5 700 kg maximum certificated take-off mass shall obtain and assess continuing airworthiness information and recommendations available from the organization responsible for the type design and shall implement resulting actions considered necessary in accordance with a procedure acceptable to the State of Registry.

Std. ref. A6-I-8.5 Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 116 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A23-04 A23-05 Pre-described Finding Deferred defect closed after the deadline Known defect(s) not reported/assessed Standard’s Text The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the Airworthiness requirements applicable in the State of Registry. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; The pilot-in-command shall be responsible for reporting all known or suspected defects in the aeroplane, to the operator, at the termination of the flight. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the Airworthiness requirements applicable in the State of Registry.

Std. ref. A6-I-6.1.3 A6-I-4.3.1(a)(c) A6-I-4.5.4 A6-I-6.1.3 Cat. 2 2 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A23 A23 V 2.0 Page 117 of 217 Instructions for completing the detailed description Indicate the nature and extent of the defect Indicate the defect and the rectification deadline PDF code A23-06 A23-07 Pre-described Finding No evidence of identification nor monitoring of significant defect Deferred defect open while the MEL rectification interval has expired Standard’s Text A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; The pilot-in-command shall be responsible for reporting all known or suspected defects in the aeroplane, to the operator, at the termination of the flight. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the Airworthiness requirements applicable in the State of Registry. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; The pilot-in-command shall be responsible for reporting all known or suspected defects in the aeroplane, to the operator, at the termination of the flight.

Std. ref. A6-I-4.3.1(a)(c) A6-I-4.5.4 A6-I-6.1.3 A6-I-4.3.1(a)(c) A6-I-4.5.4 Cat. 2 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A23 A23 V 2.0 Page 118 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code A23-08 Pre-described Finding Technical logbook entry not understood by the flight crew members Standard’s Text The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the Airworthiness requirements applicable in the State of Registry. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; The pilot-in-command shall be responsible for reporting all known or suspected defects in the aeroplane, to the operator, at the termination of the flight. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the Airworthiness requirements applicable in the State of Registry.

Std. ref. A6-I-6.1.3 A6-I-4.3.1(a)(c) A6-I-4.5.4 A6-I-6.1.3 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A23 V 2.0 Page 119 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code A23-09 A23-10 A23-11 A23-12 Pre-described Finding Rectification interval set in the ATLB exceeding the rectification interval prescribed by the MEL (but still within the MEL rectification interval) Required maintenance action not performed or not in accordance with applicable (MEL/AMM/SRM) instructions. Maintenance action not performed by appropriately qualified personnel. Defect deferred but without applying (correctly) the required (M), (O) and/or other procedures prescribed by the MEL.

A flight shall not be commenced until flight Standard’s Text The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the Airworthiness requirements applicable in the State of Registry. preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; An operator shall employ a person or group of persons to ensure that all maintenance is carried out in accordance with the maintenance control manual. The maintenance organization shall employ the necessary personnel to plan, perform, supervise, inspect and release the work to be performed. A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; The pilot-in-command shall be responsible for reporting all known or suspected defects in the A6-I-4.3.1(a) Std. ref. A6-I-6.1.3 A6-I-8.1.4 A6-I-8.7.6.2 A6-I-4.3.1(a)(c) A6-I-4.5.4 Cat. 2 3 3 3 Std. I I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A23 A23 A23 A23 V 2.0 Page 120 of 217 Instructions for completing the detailed description PDF code A23-13 Pre-described Finding Maintenance personnel working on the aircraft without using appropriate tooling and/or technical data Standard’s Text aeroplane, to the operator, at the termination of the flight. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in-command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane's compliance with the Airworthiness requirements applicable in the State of Registry. The maintenance organization shall have the necessary technical data, equipment, tools and material to perform the work for which it is approved. An operator shall not operate an aeroplane unless it is maintained and released to service by an organization approved in accordance with 8.7, or under an equivalent system, either of which shall be acceptable to the State of Registry.

Std. ref. A6-I-6.1.3 A6-I-8.7.5.2 A6-I-8.1.2 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A23 V 2.0 Page 121 of 217 Instructions for completing the detailed description Indicate the defect unnoticed PDF code A24-01 A24-02 A24-03 A24-04 Pre-described Finding Pre-flight inspection performed but the pilot in command did not certify that he is satisfied that the aircraft is airworthy Pilot in command certified that he is satisfied that the aircraft is airworthy before the pre-flight inspection was performed Pre-flight inspection performed but without recording significant defects Pre-flight inspection not performed Inspecting Instructions Check that the pre-flight or equivalent inspection is performed and duly certified. Standard’s Text A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; c) a maintenance release as prescribed in 8.8 has been issued in respect of the aeroplane; Std. ref. A6-I-4.3.1(a)(c) A6-I-4.3.1(a)(c) A6-I-4.3.1(a)(c) A6-I-4.3.1(a)(c) Cat. 1 2 2 3 Inspections Item Title Pre-flight Inspection Std. I I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item A24 Inspection Item A24 A24 A24 A24 V 2.0 Page 122 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B01-01 B01-02 Pre-described Finding Equipment installations obviously not in compliance with Annex 8, Part IIIA/B, Chapter 4 Cabin interior layout obviously not furnished in accordance with certified design specifications concerning flammable materials Inspecting Instructions Check general condition, including lavatories, general condition and smoke detection systems, the condition of the overhead bins, flammable furnishings, Check the stowage of baggage/equipment, or heavy/hard pointed objects which might be stored in the toilets (waste bags temporarily stowed in a locked toilet is considered acceptable). Check the service carts manufactured after 4 November 2005 for proper braking action. Note: findings should only be raised in those cases where the braking action is obviously not meeting the standard. Carts with defective brakes may be used as storage carts in the galley as long as such defective carts are properly labelled. Standard’s Text Under all anticipated operating conditions, the aeroplane shall not possess any feature or characteristic that renders it unsafe. Compliance with the appropriate airworthiness requirements shall be based on evidence either from tests, calculations, or calculations based on tests, provided that in each case the accuracy achieved will ensure a level of airworthiness equal to that which would be achieved were direct tests conducted. The tests of 1.5.1 shall be such as to provide reasonable assurance that the aeroplane, its components and equipment are reliable and function correctly under the anticipated operating conditions. Instrument and equipment installations shall comply with the Standards of Chapter 4. Fire precautions. The design of the aeroplane and the materials used in its manufacture, including cabin interior furnishing materials replaced during major refurbishing, shall be such as to minimize the possibility of in-flight and ground fires and also to minimize the production of smoke and toxic gases in the event of a fire. Means shall be provided to contain or to detect and extinguish such fires as might occur in such a way that no additional danger to the aeroplane is caused.

Std. ref. A8-IIIA-1.4, A8-IIIB-1.3 A8-IIIA-1.5, A8-IIIB-1.4 A8-IIIA-8.2, A8-IIIB-6.2 A8-IIIA-4.1.6 (f) Cat. 2 2 Inspections Item Title General Internal Condition Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B01 Inspection Item B01 B01 V 2.0 Page 123 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B01-03 Pre-described Finding Lavatory(s) not equipped with smoke detection system .

The design of the aeroplane and the materials used in its manufacture shall be such as to minimize the possibility of in-flight and ground fires, to minimize the production of smoke and toxic gases in the event of a fire and to delay the occurrence of flashover in the cabin. Means shall be provided to contain or to detect and extinguish such fires as might occur in such a way that no additional danger to the aeroplane is caused. Lavatories installed in aeroplanes shall be equipped with a smoke detection system and a built-in fire extinguisher system for each receptacle intended for the disposal of towels, paper or waste. The design of the aeroplane and the materials used in its manufacture shall be such as to minimize the possibility of in-flight and ground fires, to minimize the production of smoke and toxic gases in the event of a fire and to delay the occurrence of flashover in the cabin. Means shall be provided to contain or to detect and extinguish such fires as might occur in such a way that no additional danger to the aeroplane is caused. Lavatories installed in aeroplanes shall be equipped with a smoke detection system and a built-in fire extinguisher system for each receptacle intended for the disposal of towels, paper or waste.

1) 1) Standard’s Text Fire precautions. Part IIIB. Aeroplanes over 5700 KG for which application for certification was submitted on or after March 2004 Subpart D. Design and construction D.2 Systems design features Fire precautions.

Std. ref. A8-IIIB-4.2 (f) A8-IIIB-4.2(f) Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B01 V 2.0 Page 124 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B01-04 B01-05 B01-06 Pre-described Finding Disposal receptacles not equipped with a built-in fire extinguisher system Crew carry-on baggage not adequately and securely stowed during flight Loose or heavy objects in the cabin/galleys .

The design of the aeroplane and the materials used in its manufacture shall be such as to minimize the possibility of in-flight and ground fires, to minimize the production of smoke and toxic gases in the event of a fire and to delay the occurrence of flashover in the cabin. Means shall be provided to contain or to detect and extinguish such fires as might occur in such a way that no additional danger to the aeroplane is caused. Lavatories installed in aeroplanes shall be equipped with a smoke detection system and a built-in fire extinguisher system for each receptacle intended for the disposal of towels, paper or waste.

1) Standard’s Text Part IIIB. Aeroplanes over 5700 KG for which application for certification was submitted on or after March 2004 Subpart D. Design and construction D.2 Systems design features f) Fire precautions. The operator shall ensure that all baggage carried onto an aeroplane and taken into the passenger cabin is adequately and securely stowed. Provisions shall be made in the design of the aeroplane to protect the occupants, in the event of an emergency landing, from fire and from the direct effects of deceleration forces as well as from injuries arising from the effect of deceleration forces on the aeroplane's interior equipment.

Std. ref. A8-IIIB-4.2(f) A6-I-4.8 A8-IIIA-4.1.7.1 A8-IIIB-4.6.1 Cat. 3 3 3 Std. I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B01 B01 B01 V 2.0 Page 125 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B01-07 B01-08 B01-09 B01-10 Pre-described Finding Cabin equipment not properly secured Inappropriate stowage of luggage or loose articles in the toilets Lavatory smoke detection system obstructed Lavatory inoperative (not placarded as such and not confirmed with MEL restrictions if any) .

The design of the aeroplane and the materials used in its manufacture shall be such as to minimize the possibility of in-flight and ground fires, to minimize the production of smoke and toxic gases in the event of a fire and to delay the occurrence of flashover in the cabin. Means shall be provided to contain or to detect and extinguish such fires as might occur in such a way that no additional danger to the aeroplane is caused. Lavatories installed in aeroplanes shall be equipped with a smoke detection system and a built-in fire extinguisher system for each receptacle intended for the disposal of towels, paper or waste.

1) Standard’s Text Provisions shall be made in the design of the aeroplane to protect the occupants, in the event of an emergency landing, from fire and from the direct effects of deceleration forces as well as from injuries arising from the effect of deceleration forces on the aeroplane's interior equipment. The operator shall ensure that all baggage carried onto an aeroplane and taken into the passenger cabin is adequately and securely stowed. Part IIIB. Aeroplanes over 5700 KG for which application for certification was submitted on or after March 2004 Subpart D. Design and construction D.2 Systems design features f) Fire precautions. The operator shall include in the operations manual a minimum equipment list (MEL), approved by the State of the Operator which will enable the pilot-in- command to determine whether a flight may be commenced or continued from any intermediate stop should any instrument, equipment or systems become Std. ref. A8-IIIA-4.1.7.1 A8-IIIB-4.6.1 A6-I-4.8 A8-IIIB-4.2(f) A6-I-6.1.3 Cat. 3 3 3 3 Std. I I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B01 B01 B01 B01 V 2.0 Page 126 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B01-11 B01-12 B01-13 B01-14 B01-15 Pre-described Finding Galley/lavatory waste receptacle access door cover inoperative (outside MEL limits) Damaged wall panels Obviously defective brakes of service cart(s) Covers damaged/missing exposing sharp edges and/or cables and wires Overhead bins unserviceable (and not identified as such) Standard’s Text inoperative. Where the State of the Operator is not the State of Registry, the State of the Operator shall ensure that the MEL does not affect the aeroplane’s compliance with the airworthiness requirements applicable in the State of Registry. For new models of carts identified and manufactured after 4 November 2005: The brake system shall hold the fully loaded cart, in the forward and aft orientation, stationary on an 11 degree slope carpeted with low-pile carpet representative of that used by the airlines.

Std. ref. (E)TSO-C175 SAE AS8056 EUROCAE ED- 121 Cat. 3 1 3 3 3 Std. M M M M M

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B01 B01 B01 B01 B01 V 2.0 Page 127 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B02-01 B02-02 B02-03 Pre-described Finding Strap or buckle worn or damaged Cabin Crew seat(s) not equipped with safety harness (only seat belt) Cabin Crew life jackets (when required) not easily accessible accommodate the minimum required number of cabin crew members (information available in the Operations Manual). emergency, this finding should be addressed under the item B12 – Access to emergency exit. for the use of cabin crew members.

1 January 1981 1 January 1981 Inspecting Instructions Check general condition and serviceability of the cabin crew seats. Note: If a cabin crew seat is found unserviceable check against MEL and check if the number of serviceable ones can Note: If a cabin crew seat is found not to retract automatically impeding the rapid evacuation of the aeroplane in an Check presence and condition of the safety harness and/or belt. Note: Aeroplanes for which the individual CofA was issued on or after 1 January 1981 must be fitted with safety harnesses Check accessibility of life jackets. Check the serviceability of the communication system (Cockpit to Cabin and Cabin to Cabin). In case of unserviceability, check against the MEL. Standard’s Text 6.16.1 Aeroplanes for which the individual certificate of airworthiness is first issued on or after All aeroplanes shall be equipped with a forward or rearward facing (within 15 degrees of the longitudinal axis of the aeroplane) seat, fitted with a safety harness for the use of each cabin crew member required to satisfy the intent of 12.1 in respect of emergency evacuation. 6.16.1 Aeroplanes for which the individual certificate of airworthiness is first issued on or after All aeroplanes shall be equipped with a forward or rearward facing (within 15 degrees of the longitudinal axis of the aeroplane) seat, fitted with a safety harness for the use of each cabin crew member required to satisfy the intent of 12.1 in respect of emergency evacuation. 6.5.2.1 Landplanes shall carry the equipment prescribed in 6.5.2.2: Std. ref. A6-I-6.16.1 A6-I-6.16.1 A6-I-6.5.2 Cat. 1 2 2 Inspections Item Title Cabin Attendant's Station/Crew Rest Area Std. I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B02 Inspection Item B02 B02 B02 V 2.0 Page 128 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B02-04 B02-05 Pre-described Finding Cabin Crew seat(s) unserviceable (outside MEL limits) Cabin crew harness/seat belt not available or unserviceable 1 January 1981 1 January 1981 Standard’s Text a) when flying over water and at a distance of more than 93 km (50 NM) away from the shore, in the case of landplanes operated in accordance with 5.2.9 or 5.2.10; b) when flying en route over water beyond gliding distance from the shore, in the case of all other landplanes; and c) when taking off or landing at an aerodrome where, in the opinion of the State of the Operator, the take-off or approach path is so disposed over water that in the event of a mishap there would be a likelihood of a ditching. 6.5.2.2 The equipment referred to in 6.5.2.1 shall comprise one life jacket or equivalent individual flotation device for each person on board, stowed in a position easily accessible from the seat or berth of the person for whose use it is provided. Note.- "Landplanes" includes amphibians operated as landplanes. 6.16.1 Aeroplanes for which the individual certificate of airworthiness is first issued on or after All aeroplanes shall be equipped with a forward or rearward facing (within 15 degrees of the longitudinal axis of the aeroplane) seat, fitted with a safety harness for the use of each cabin crew member required to satisfy the intent of 12.1 in respect of emergency evacuation. 6.16.1 Aeroplanes for which the individual certificate of airworthiness is first issued on or after All aeroplanes shall be equipped with a forward or rearward facing (within 15 degrees of the Std. ref. A6-I-6.16.1 A6-I-6.16.1 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B02 B02 V 2.0 Page 129 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B02-06 B02-07 B02-08 Pre-described Finding Cabin Crew seat(s) obviously not installed correctly (more than 15 degrees from the longitudinal axis) Cabin Crew seats not correctly located Communication equipment unserviceable (outside MEL limits) 1 January 1981 Standard’s Text longitudinal axis of the aeroplane) seat, fitted with a safety harness for the use of each cabin crew member required to satisfy the intent of 12.1 in respect of emergency evacuation. 6.16.1 Aeroplanes for which the individual certificate of airworthiness is first issued on or after All aeroplanes shall be equipped with a forward or rearward facing (within 15 degrees of the longitudinal axis of the aeroplane) seat, fitted with a safety harness for the use of each cabin crew member required to satisfy the intent of 12.1 in respect of emergency evacuation. 6.16.3 Cabin crew seats provided in accordance with 6.16.1 and 6.16.2 shall be located near floor level and other emergency exits as required by the State of Registry for emergency evacuation.

Std. ref. A6-I-6.16.1 A6-I-6.16.3 Cat. 3 3 3 Std. I I M

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B02 B02 B02 V 2.0 Page 130 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B03-01 B03-02 Pre-described Finding Medical supplies not at the indicated location Contents of the medical kit past expiration date check) date. A First Aid Kit, Emergency Medical Kit, Universal precaution kit without a date does not constitute a finding. However, if stated expiry date has been exceeded, then this should be reported as a finding.

Inspecting Instructions Check for presence, accessibility, and identification of medical supplies. Note: A First-Aid kit or a Medical kit or a universal precaution kit is only an ICAO recommendation. Note: ICAO does not require First Aid Kits / Emergency Medical Kits/Universal precaution kits to have an expiration (or next Standard’s Text The operator shall inform the passengers of the location and general manner of use of the principal emergency equipment carried for collective use. 6.2.2 An aeroplane shall be equipped with: a) accessible and adequate medical supplies; Recommendation.- Medical supplies should comprise: 1) one or more first-aid kits for the use of cabin crew in managing incidents of ill health; and 2) for aeroplanes required to carry cabin crew as part of the operating crew, one universal precaution kit (two for aeroplanes authorized to carry more than 250 passengers) for the use of cabin crew members in managing incidents of ill health associated with a case of suspected communicable disease, or in the case of illness involving contact with body fluids; and. 3) for aeroplanes authorized to carry more than 100 passengers, on a sector length of more than two hours, a medical kit, for the use of medical doctors or other qualified persons in treating in- flight medical emergencies. Note.- Guidance on the types, number, location and contents of the medical supplies is given in Attachment B.

Std. ref. A6-I-4.2.12.2 A6-I-6.2.2 Cat. 1 3 Inspections Item Title First Aid Kit / Emergency Medical Kit Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B03 Inspection Item B03 B03 V 2.0 Page 131 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B03-03 B03-04 B03-05 Pre-described Finding Contents of the first aid kit/universal precaution kit past expiration date Medical supplies not identified as such Medical supplies not available or not accessible during flight Note.- Guidance on the types, number, location Standard’s Text 6.2.2 An aeroplane shall be equipped with: a) accessible and adequate medical supplies; Recommendation.- Medical supplies should comprise: 1) one or more first-aid kits for the use of cabin crew in managing incidents of ill health; and 2) for aeroplanes required to carry cabin crew as part of the operating crew, one universal precaution kit (two for aeroplanes authorized to carry more than 250 passengers) for the use of cabin crew members in managing incidents of ill health associated with a case of suspected communicable disease, or in the case of illness involving contact with body fluids; and. 3) for aeroplanes authorized to carry more than 100 passengers, on a sector length of more than two hours, a medical kit, for the use of medical doctors or other qualified persons in treating in- flight medical emergencies. and contents of the medical supplies is given in Attachment B. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. 6.2.2 An aeroplane shall be equipped with: a) accessible and adequate medical supplies; Recommendation.- Medical supplies should comprise: Std. ref. A6-I-6.2.2 A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A6-I-6.2.2 Cat. 1 2 3 Std. I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B03 B03 B03 V 2.0 Page 132 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text 1) one or more first-aid kits for the use of cabin crew in managing incidents of ill health; and 2) for aeroplanes required to carry cabin crew as part of the operating crew, one universal precaution kit (two for aeroplanes authorized to carry more than 250 passengers) for the use of cabin crew members in managing incidents of ill health associated with a case of suspected communicable disease, or in the case of illness involving contact with body fluids; and. 3) for aeroplanes authorized to carry more than 100 passengers, on a sector length of more than two hours, a medical kit, for the use of medical doctors or other qualified persons in treating in- flight medical emergencies. Note.- Guidance on the types, number, location and contents of the medical supplies is given in Attachment B.

Std. ref.

Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 133 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B04-01 B04-02 B04-03 Pre-described Finding HFE not at indicated location HFE not marked with the appropriate operating instructions HFE empty, unserviceable or missing (outside MEL limits) MEL to verify compliance with the applicable (M) and/or (O) procedures. If the latter MEL actions have not been applied, a finding should be raised using the "detection / reporting / assessment of significant technical defect" procedure (see Chapter 4.2 above). systems to monitor the condition of the extinguishers. An extinguisher without a date does not necessarily constitute a finding. However, if the expiry date (or next inspection date) is overdue, consider it as unserviceable.

gauge (if installed), check expiration date (if any). If considerably low weight, consider it unserviceable.

Inspecting Instructions Check if the installed extinguisher(s) is at the indicated location and easily accessible. Check if the installed extinguisher is correctly secured in its bracket. Check if the installed extinguisher(s) is marked with the appropriate operating instructions. Check if the installed extinguisher(s), including the extinguishing agent release mechanism, is serviceable – check pressure Note: Often HFEs in excess of those required (by MEL provisions) may be U/S, however in such a case, check against the Note: ICAO does not require hand fire extinguishers to have an expiration (or next check) date. Operators may employ various Standard’s Text Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. An aeroplane shall be equipped with: b) portable fire extinguishers of a type which, when discharged, will not cause dangerous contamination of the air within the aeroplane. At least one shall be located in: 2) each passenger compartment that is separate from the pilot's compartment and that is not readily accessible to the flight crew; Note.- Any portable fire extinguisher so fitted in Std. ref. A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 A8-IIIA-8.3 A8-IIIB-.6.3 A8-V-6.3 A6-I-.2.2(b)(2) 2 2 3 Cat.

Hand Fire extinguishers I I I Inspections Item Title Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 B04 Inspection Item Inspection Item B04 B04 B04 V 2.0 Page 134 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B04-04 B04-05 Pre-described Finding HFE not correctly secured HFE not readily accessible Standard’s Text accordance with the certificate of airworthiness of the aeroplane may count as one prescribed. Provisions shall be made in the design of the aeroplane to protect the occupants, in the event of an emergency landing, from fire and from the direct effects of deceleration forces as well as from injuries arising from the effect of deceleration forces on the aeroplane’s interior equipment. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked.

Std. ref. A8-IIIA-4.1.7.1 A8-IIIB-4.6.1 A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 3 3 Cat.

I I Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B04 B04 V 2.0 Page 135 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B05-01 Pre-described Finding Life jackets / Flotation devices not easily accessible and required for the type of flight monitor the condition of the life jackets. A life jacket or flotation device without a date does not necessarily constitute a finding. However, if the expiry date (or next inspection date) is overdue, consider it as unserviceable. neither the inbound nor the outbound flight or series of flights are over-water flights, then findings should not be raised for this inspection item. G).

Standard’s Text All seaplanes for all flights shall be equipped with: Inspecting Instructions Check for presence, access, sufficient number and serviceability. Note: ICAO does not require life jackets to have an expiration (or next check) date. Operators may employ various systems to Note: ICAO requires the carriage of life jackets/flotation devices only for over-water flights (see Annex 6 references below). If Note: In the case where spare life jackets have been found to be unserviceable, this should reported as a General Remark (Cat. a) one life jacket, or equivalent individual flotation device, for each person on board, stowed in a position easily accessible from the seat or berth of the person for whose use it is provided; Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. 6.5.2.1 Landplanes shall carry the equipment prescribed in 6.5.2.2: a) when flying over water and at a distance of more than 93 km (50 NM) away from the shore, in the case of landplanes operated in accordance with 5.2.9 or 5.2.10; b) when flying en route over water beyond gliding distance from the shore, in the case of all other landplanes; and c) when taking off or landing at an aerodrome where, in the opinion of the State of the Operator, the take-off or Std. ref.

A6-I-6.5.1(a) A8-IIIA-8.3 A8-IIIB-6.3 A8-V-6.3 A6-I-6.5.2 Cat.

Inspections Item Title Life jackets / Flotation devices Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B05 Inspection Item B05 V 2.0 Page 136 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B05-02 Pre-described Finding Insufficient number of serviceable Life jackets / Flotation devices available and required for the type of flight Standard’s Text All seaplanes for all flights shall be equipped with: 6.5.2.1 Landplanes shall carry the equipment approach path is so disposed over water that in the event of a mishap there would be a likelihood of a ditching. 6.5.2.2 The equipment referred to in 6.5.2.1 shall comprise one life jacket or equivalent individual flotation device for each person on board, stowed in a position easily accessible from the seat or berth of the person for whose use it is provided. Note.- "Landplanes" includes amphibians operated as landplanes. a) one life jacket, or equivalent individual flotation device, for each person on board, stowed in a position easily accessible from the seat or berth of the person for whose use it is provided; Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. prescribed in 6.5.2.2: a) when flying over water and at a distance of more than 93 km (50 NM) away from the shore, in the case of landplanes operated in accordance with 5.2.9 or 5.2.10; b) when flying en route over water beyond gliding distance from the shore, in the case of all other landplanes; and c) when taking off or landing at an aerodrome where, in the opinion of the State of the Operator, the take-off or approach path is so disposed over water that in the event of a mishap there would be a likelihood of a ditching.

Std. ref.

A6-I-6.5.1(a) A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A6-I-6.5.2 Cat.

I Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B05 V 2.0 Page 137 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text 6.5.2.2 The equipment referred to in 6.5.2.1 shall comprise one life jacket or equivalent individual flotation device for each person on board, stowed in a position easily accessible from the seat or berth of the person for whose use it is provided. Note.- "Landplanes" includes amphibians operated as landplanes.

Std. ref.

Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 138 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B06-01 B06-02 Pre-described Finding No extension belts available on board and required Passenger seats in poor condition Inspecting Instructions Check condition of seats and belts. Check for the availability and condition of extension belts (if needed). Standard’s Text An aeroplane shall be equipped with: c) 1) a seat or berth for each person over an age to be determined by the State of the Operator; 2) a seat belt for each seat and restraining belts for each berth; Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. 4.4.1 Seating and restraints Adequate seating and restraints shall be provided for the occupants, taking account of the likely flight and emergency landing loads to be encountered. Attention shall be paid to minimizing injury to occupants due to contact with surrounding structure during the operation of the aeroplane. An aeroplane shall be equipped with: c) 1) a seat or berth for each person over an age to be determined by the State of the Operator; 2) a seat belt for each seat and restraining belts for each berth; Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. 4.4.1 Seating and restraints Adequate seating and restraints shall be provided for the occupants, taking account of the likely flight and emergency landing loads to be encountered. Attention shall be paid to minimizing injury to occupants due to Std. ref. A6-I-6.2.2(c) A8-IIIB-4.4.1 A6-I-6.2.2(c) A8-IIIB-4.4.1 Cat. 3 1 Inspections Item Title Seat belt and seat condition Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B06 Inspection Item B06 B06 V 2.0 Page 139 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B06-03 B06-04 Pre-described Finding Strap or buckle worn out or damaged No serviceable seat belt available for each passenger on board Standard’s Text contact with surrounding structure during the operation of the aeroplane. An aeroplane shall be equipped with: c) 1) a seat or berth for each person over an age to be determined by the State of the Operator; 2) a seat belt for each seat and restraining belts for each berth; Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. D.4.1 Seating and restraints Adequate seating and restraints shall be provided for the occupants, taking account of the likely flight and emergency landing loads to be encountered. Attention shall be paid to minimizing injury to occupants due to contact with surrounding structure during the operation of the aeroplane. An aeroplane shall be equipped with: c) 1) a seat or berth for each person over an age to be determined by the State of the Operator; 2) a seat belt for each seat and restraining belts for each berth; Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. 4.4.1 Seating and restraints Adequate seating and restraints shall be provided for the occupants, taking account of the likely flight and emergency landing loads to be encountered. Attention shall be paid to minimizing injury to occupants due to contact with surrounding structure during the operation of the aeroplane.

Std. ref. A6-I-6.2.2(c) A8-IIIB-4.4.1 A6-I-6.2.2(c) A8-IIIB-4.4.1 Cat. 2 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B06 B06 V 2.0 Page 140 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B06-05 B06-06 Pre-described Finding Seat(s) unserviceable and not identified as such Baby berth(s) used without restraining belts Standard’s Text An aeroplane shall be equipped with: c) 1) a seat or berth for each person over an age to be determined by the State of the Operator; 2) a seat belt for each seat and restraining belts for each berth; Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. 4.4.1 Seating and restraints Adequate seating and restraints shall be provided for the occupants, taking account of the likely flight and emergency landing loads to be encountered. Attention shall be paid to minimizing injury to occupants due to contact with surrounding structure during the operation of the aeroplane. An aeroplane shall be equipped with: c) 1) a seat or berth for each person over an age to be determined by the State of the Operator; 2) a seat belt for each seat and restraining belts for each berth; Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. 4.4.1 Seating and restraints Adequate seating and restraints shall be provided for the occupants, taking account of the likely flight and emergency landing loads to be encountered. Attention shall be paid to minimizing injury to occupants due to contact with surrounding structure during the operation of the aeroplane.

Std. ref. A6-I-6.2.2(c) A8-IIIB-4.4.1 A6-I-6.2.2(c) A8-IIIB-4.4.1 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B06 B06 V 2.0 Page 141 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B07-01 Pre-described Finding Emergency exit sign(s) lens/cover missing or broken path to emergency exits in smoke filled cabins. Aeroplanes over 5 700 kg, for which application for certification was submitted before 13 June 1960, are not required to have an illumination of the escape path and exits. Aeroplanes over 5 700 kg, for which application for certification was submitted before 2 March 2004, are not required to have the visual indication of the path to emergency exits in smoke filled cabins. If an illuminated visual indication system is used, by means of low-mounted lights or the photoluminescent system, both requirements are met. Although the visual indication is not required by ICAO for most aircraft, the vast majority of aircraft is already equipped with such indications. Any defects of such means of indication should be governed by the MEL; the finding should make reference to the MEL. into the night, and aircraft departed at night and arrived in daytime. When inspecting daylight only flights, the absence or unserviceability of any electric torch does not constitute a finding. This should however be reported as General Remark (Cat. G). cabin crew from their normal positions. This should however be reported as a General Remark (Cat. G).

Inspecting Instructions Check for presence and condition of the emergency exit signs, lighting and marking and torches. Check for presence and condition of an escape path illumination system. Check for presence and condition of the visual indication of the path to emergency exits in smoke filled cabins. Check for the presence of operating instructions on the emergency exits. Note: Inspectors should be reminded that there is a difference between illuminated escape paths and a visual indication of the Check for appropriate flashlights are readily available at all crew member stations. Check their condition, serviceability and access. Please note that flights departing in daylight, but extending into the night, shall meet this requirement. Note: Only aircraft operated at night require electric torches for the crew. This includes flights departing in daylight but extending Note: If the proper functioning of the torch is significantly affected as a result of weak batteries, consider it unserviceable. Note: If only personal torches are available, this should not be considered as a finding provided they are readily available to the Standard’s Text Ch. 4.1.7 - Emergency landing provisions 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. 4.1.7.3 The interior layout of the cabin and the position and Std. ref. A8-IIIA-4.1.7 Cat. 1 Inspections Item Title Emergency exit, lighting and marking, Torches Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B07 Inspection Item B07 V 2.0 Page 142 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text number of emergency exits, including the means of locating and illuminating the escape paths and exits shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts.

Std. ref. A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A8-IIIB-8.4 Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 143 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B07-02 B07-03 Pre-described Finding Insufficient number of serviceable torches for each cabin crew member during night operations Electric torches not readily accessible for some of the cabin crew during night operations Standard’s Text 4.6.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane and shall be shown to be suitable for their intended purpose. 4.6.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits, shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. 4.6.4 On aeroplanes certificated for ditching conditions, provisions shall be made in the design to give maximum practicable assurance that safe evacuation from the aeroplane of passengers and crew can be executed in case of ditching. All aeroplanes, when operated at night shall be equipped with: f) an electric torch for each crew member station. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. All aeroplanes, when operated at night shall be equipped with: f) an electric torch for each crew member station. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked.

Std. ref. A8-IIIB- 4.6.2-4 A6-I- 6.10(f) A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A6-I- 6.10(f) A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 Cat. 2 2 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B07 B07 V 2.0 Page 144 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B07-04 Pre-described Finding Emergency exit sign(s) out of order (outside MEL limits).

Standard’s Text Ch. 4.1.7 - Emergency landing provisions 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. 4.1.7.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. 8.4 Evacuation The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. 4.6.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an Std. ref. A8-IIIA-4.1.7 A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A8-IIIB-8.4 A8-IIIB- 4.6.2-4 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B07 V 2.0 Page 145 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B07-05 Pre-described Finding No means for illuminating the escape paths Standard’s Text emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane and shall be shown to be suitable for their intended purpose. 4.6.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits, shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. 4.6.4 On aeroplanes certificated for ditching conditions, provisions shall be made in the design to give maximum practicable assurance that safe evacuation from the aeroplane of passengers and crew can be executed in case of ditching. Ch. 4.1.7 - Emergency landing provisions 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. 4.1.7.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. Emergency lighting shall be provided and shall have the following characteristics: a) independence from main electrical supply; b) automatic activation upon loss of normal power/impact; c) visual indication of the path to emergency exits in smoke- filled cabin conditions; d) illumination both inside and outside the aeroplane during evacuation; and e) no additional hazard in the event of fuel spillage.

Std. ref. A8-IIIA-4.1.7 A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A8-IIIB-8.5 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B07 V 2.0 Page 146 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed and the MEL reference Indicate the particulars of the situation observed PDF code B07-06 B07-07 Pre-described Finding System for visually indicating the escape path(s) unserviceable (outside MEL limits). Emergency exit(s) not marked with the appropriate operating instructions Standard’s Text 4.6.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane and shall be shown to be suitable for their intended purpose. 4.6.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits, shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. 4.6.4 On aeroplanes certificated for ditching conditions, provisions shall be made in the design to give maximum practicable assurance that safe evacuation from the aeroplane of passengers and crew can be executed in case of ditching. Ch. 4.1.7 - Emergency landing provisions 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. 4.1.7.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. 4.6.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane and shall be Std. ref. A8-IIIB- 4.6.2-4 A8-IIIA-4.1.7 A8-IIIB- 4.6.2-4 Cat. 3 2 Std. M I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B07 B07 V 2.0 Page 147 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B07-08 B07-09 Pre-described Finding Cabin crew members’ electric torches not readily accessible during night operations Emergency exit(s), lighting and marking unserviceable (outside MEL) Standard’s Text shown to be suitable for their intended purpose. 4.6.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits, shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. 4.6.4 On aeroplanes certificated for ditching conditions, provisions shall be made in the design to give maximum practicable assurance that safe evacuation from the aeroplane of passengers and crew can be executed in case of ditching. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. All aeroplanes, when operated at night shall be equipped with: f) an electric torch for each crew member station. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. Ch. 4.1.7 - Emergency landing provisions 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. 4.1.7.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing.

Std. ref. A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A6-I- 6.10(f) A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A8-IIIA-4.1.7 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B07 B07 V 2.0 Page 148 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B07-10 Pre-described Finding Number of passengers on board exceeds the maximum allowed in case of unserviceable Standard’s Text 8.4 Evacuation The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. 4.6.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane and shall be shown to be suitable for their intended purpose. 4.6.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits, shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. 4.6.4 On aeroplanes certificated for ditching conditions, provisions shall be made in the design to give maximum practicable assurance that safe evacuation from the aeroplane of passengers and crew can be executed in case of ditching. Ch. 4.1.7 - Emergency landing provisions 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an Std. ref. A8-IIIB-8/.4 A8-IIIB- 4.6.2-4 A8-IIIA-4.1.7 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B07 V 2.0 Page 149 of 217 Instructions for completing the detailed description PDF code Pre-described Finding emergency exit(s) Standard’s Text emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. 4.1.7.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. 8.4 Evacuation The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. 4.6.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane and shall be shown to be suitable for their intended purpose. 4.6.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits, shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. 4.6.4 On aeroplanes certificated for ditching conditions, Std. ref. A8-IIIB-8.4 A8-IIIB- 4.6.2-4 Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 150 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text provisions shall be made in the design to give maximum practicable assurance that safe evacuation from the aeroplane of passengers and crew can be executed in case of ditching.

Std. ref.

Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 151 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B08-01 Pre-described Finding No equipment for making the pyrotechnical distress signals when required for long-range over water flights by checking the expiry (or next inspection) date. If the expiry (or next inspection) date is overdue consider unserviceable and check against the aeroplane MEL. the inbound nor the outbound flight or series of flights are over-water flights, then findings should not be raised for this inspection item. Remark (Cat. G). MHZ, whereas the required one(s) does, this should be reported as a General Remark (Cat. G). understood as the first certificate of airworthiness delivered to the aircraft after production.

Radio Station Licence (although there is no requirement for the frequency to be listed there), or in the Operations Manual (included in the list containing the emergency and survival equipment).

Inspecting Instructions Check number and serviceability of slides/slide rafts/life rafts. Note: Serviceability of the slides/slide rafts may be assessed by checking the pressure gauge (if installed) or, when available, Note: ICAO requires the carriage of floatation devices only for over-water flights (see the Annex 6 references below). If neither Check presence and type of ELT (s) and serviceability. So as to verify that an ELT is broadcasting on 406 MHz, evidence may be found on the ELT itself (if portable) ,on the Aircraft Note: If no evidence could be found as to what frequency the ELT is broadcasting, then this should be reported as a General Note: In case any ELT(s) in excess of those required are not capable of simultaneously transmitting on 406 MHz and 121.5 Note: Where the ICAO references mention "the first issue of the individual certificate of airworthiness", this should be Check equipment for pyrotechnical distress signals (if required and easily accessible). Standard’s Text 6.5.3.1 In addition to the equipment prescribed in 6.5.1 or 6.5.2 whichever is applicable, the following equipment shall be installed in all aeroplanes when used over routes on which the aeroplane may be over water and at more than a distance corresponding to 120 minutes at cruising speed or 740 km (400 NM), whichever is the lesser, away from land suitable for making an emergency landing in the case of aircraft operated in accordance with 5.2.9 or 5.2.10, and 30 minutes or 185 km (100 NM), whichever is the lesser, for all other aeroplanes: b) equipment for making the pyrotechnical distress signals described in Annex 2.; Std. ref. A6-I-6.5.3.1(b) Cat. 2 Inspections Item Title Slides/Life-Rafts (as required), ELT Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B08 Inspection Item B08 V 2.0 Page 152 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B08-02 B08-03 Pre-described Finding Insufficient number of serviceable slides/slide rafts Insufficient number of serviceable rafts and required for long-range over water flights Standard’s Text Ch. 4.1.7 - Emergency landing provisions 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. 4.1.7.3 The interior layout of the cabin and the position and number of emergency exits, including the means of locating and illuminating the escape paths and exits shall be such as to facilitate rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. 6.5.3.1 In addition to the equipment prescribed in 6.5.1 or 6.5.2 whichever is applicable, the following equipment shall be installed in all aeroplanes when used over routes on which the aeroplane may be over water and at more Std. ref. A8-IIIA-4.1.7 A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A8-IIIB-8.4 A6-I-6.5.3.1(a) Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B08 B08 V 2.0 Page 153 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B08-04 B08-05 B08-06 Pre-described Finding Insufficient number of compliant ELTs (outside MEL limits) No ELT capable of simultaneously transmitting on 406 MHz and 121.5 MHZ Portable ELT not at indicated location Standard’s Text than a distance corresponding to 120 minutes at cruising speed or 740 km (400 NM), whichever is the lesser, away from land suitable for making an emergency landing in the case of aircraft operated in accordance with 5.2.9 or 5.2.10, and 30 minutes or 185 km (100 NM), whichever is the lesser, for all other aeroplanes: a) life-saving rafts in sufficient numbers to carry all persons on board, stowed so as to facilitate their ready use in emergency, provided with such life-saving equipment including means of sustaining life as is appropriate to the flight to be undertaken; Except as provided for in 6.17.9, from 1 July 2008, all aeroplanes authorized to carry more than 19 passengers shall be equipped with at least one automatic ELT or two ELTs of any type. All aeroplanes authorized to carry more than 19 passengers for which the individual certificate of airworthiness is first issued after 1 July 2008 shall be equipped with at least two ELTs, one of which shall be automatic. Except as provided for in 6.17.11, from 1 July 2008, all aeroplanes authorized to carry 19 passengers or less shall be equipped with at least one ELT of any type. All aeroplanes authorized to carry 19 passengers or less for which the individual certificate of airworthiness is first issued after 1 July 2008 shall be equipped with at least one automatic ELT. ELT equipment carried to satisfy the requirements of 6.17.7, 6.17.8, 6.17.9, 6.17.10 and 6.17.11 shall operate in accordance with the relevant provisions of Annex 10,Volume III. From 1 January 2005, emergency locator transmitters shall operate on 406 MHz and 121.5 MHz simultaneously. Except as provided for in 6.17.9, from 1 July 2008, all aeroplanes authorized to carry more than 19 passengers shall be equipped with at least one automatic ELT or two ELTs of any type.

Std. ref. A6-I-6.17.8 A6-I-6.17.9 A6-I-6.17.10 A6-I-6.17.11 A6-I-6.17.12 A10-III-Ch.2- 5.1.4 A6-I-6.17.8 Cat. 3 3 3 Std. I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B08 B08 B08 V 2.0 Page 154 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text All aeroplanes authorized to carry more than 19 passengers for which the individual certificate of airworthiness is first issued after 1 July 2008 shall be equipped with at least two ELTs, one of which shall be automatic. Except as provided for in 6.17.11, from 1 July 2008, all aeroplanes authorized to carry 19 passengers or less shall be equipped with at least one ELT of any type. All aeroplanes authorized to carry 19 passengers or less for which the individual certificate of airworthiness is first issued after 1 July 2008 shall be equipped with at least one automatic ELT. ELT equipment carried to satisfy the requirements of 6.17.7, 6.17.8, 6.17.9, 6.17.10 and 6.17.11 shall operate in accordance with the relevant provisions of Annex 10,Volume III. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked.

Std. ref. A6-I-6.17.9 A6-I-6.17.10 A6-I-6.17.11 A6-I-6.17.12 A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 155 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B09-01 Feet 10 000 13 000 25 000 Metres 3 000 4 000 7 600 Pre-described Finding Portable breathing equipment not at indicated location PSI 10.152642 8.99234 5.453419 mm Hg 525.043178 465.038243 282.023193 Absolute pressure mBar 700 620 376 ft. to carry sufficient oxygen supply for 10% of the passengers, whereas ICAO requires this for all passengers. All operators should be treated equally, therefore the lower EU OPS requirements should apply. follows: hPa/ 700 620 376 Inspecting Instructions Check if the PBE is at the indicated location and adequately marked with its operating instructions. Check cabin oxygen quantity (pressure gauge or electronic display) when stored oxygen is used. Check portable breathing equipment for serviceability and minimum number (against MEL). Check number / serviceability of oxygen dispensing units or oxygen masks (when possible). Note: if the oxygen masks and bottle fittings are not compatible, consider the oxygen mask as unserviceable. Note: inspectors should take into account that EU OPS 1.770 b.2(v) requires for aircraft not certified to operate above 25.000 Note: Approximate altitude in the Standard Atmosphere corresponding to the value of absolute pressure used in this text is as Standard’s Text A flight to be operated at flight altitudes at which the atmospheric pressure in personnel compartments will be less than 700 hPa shall not be commenced unless sufficient stored breathing oxygen is carried to supply: a) all crew members and 10 per cent of the passengers for any period in excess of 30 minutes that the pressure in compartments occupied by them will be between 700 hPa and 620 hPa; and b) the crew and passengers for any period that the atmospheric pressure in compartments occupied by them will be less than 620 hPa. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 700 hPa in personnel compartments shall be equipped with oxygen storage and dispensing apparatus capable of storing and dispensing the oxygen supplies required in Annex 6 Part I Chapter 4.3.8.1. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked.

Std. ref. A6-I-4.3.8.1 A6-I-6.7.1 A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 Cat. 2 Inspections Item Title Oxygen Supply Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B09 Inspection Item B09 V 2.0 Page 156 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B09-02 B09-03 B09-04 Pre-described Finding Oxygen equipment not readily accessible and required for the type of flight Aeroplane not equipped with an automatic deployable oxygen system (individual CofA issued on or after 9 November 1998) and flight planned above FL 250 Insufficient number of required serviceable automatic deployable oxygen dispensing units - individual CofA Standard’s Text A flight to be operated at flight altitudes at which the atmospheric pressure in personnel compartments will be less than 700 hPa shall not be commenced unless sufficient stored breathing oxygen is carried to supply: a) all crew members and 10 per cent of the passengers for any period in excess of 30 minutes that the pressure in compartments occupied by them will be between 700 hPa and 620 hPa; and b) the crew and passengers for any period that the atmospheric pressure in compartments occupied by them will be less than 620 hPa. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 700 hPa in personnel compartments shall be equipped with oxygen storage and dispensing apparatus capable of storing and dispensing the oxygen supplies required in Annex 6 Part I Chapter 4.3.8.1. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 376 hPa, or which, if operated at flight altitudes at which the atmospheric pressure is more than 376 hPa, cannot descend safely within four minutes to a flight altitude at which the atmospheric pressure is equal to 620 hPa and for which the individual certificate of airworthiness is first issued on or after 9 November 1998, shall be provided with automatically deployable oxygen equipment to satisfy the requirements of Annex 6 Part I Chapter 4.3.8.2. The total number of oxygen dispensing units shall exceed the number of passenger and cabin crew seats by at least 10 per cent. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 376 hPa, or which, if operated at flight altitudes at which the atmospheric pressure is more than 376 hPa, cannot descend safely within four minutes to a flight altitude at Std. ref. A6-I-4.3.8.1 A6-I-6.7.1 A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A6-I-6.7.5 A6-I-6.7.5 Cat. 2 3 3 Std. I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B09 B09 B09 V 2.0 Page 157 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B09-05 Pre-described Finding issued on or after 9 November 1998 (outside MEL limits) Oxygen equipment not adequately marked with its operating instructions Standard’s Text which the atmospheric pressure is equal to 620 hPa and for which the individual certificate of airworthiness is first issued on or after 9 November 1998, shall be provided with automatically deployable oxygen equipment to satisfy the requirements of Annex 6 Part I Chapter 4.3.8.2. The total number of oxygen dispensing units shall exceed the number of passenger and cabin crew seats by at least 10 per cent. A flight to be operated with a pressurized aeroplane shall not be commenced unless a sufficient quantity of stored breathing oxygen is carried to supply all the crew members and passengers, as is appropriate to the circumstances of the flight being undertaken, in the event of loss of pressurization, for any period that the atmospheric pressure in any compartment occupied by them would be less than 700 hPa. In addition, when an aeroplane is operated at flight altitudes at which the atmospheric pressure is less than 376 hPa, or which, if operated at flight altitudes at which the atmospheric pressure is more than 376 hPa and cannot descend safely within four minutes to a flight altitude at which the atmospheric pressure is equal to 620 hPa, there shall be no less than a 10-minute supply for the occupants of the passenger compartment. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 700 hPa but which is provided with means of maintaining pressures greater than 700 hPa in personnel compartments shall be provided with oxygen storage and dispensing apparatus capable of storing and dispensing the oxygen supplies required in Annex 6 Part I Chapter 4.3.8.2.

Std. ref. A6-I-4.3.8.2 A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A6-I-6.7.2 Cat. 2 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B09 V 2.0 Page 158 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B09-06 Pre-described Finding Insufficient oxygen quantity and/or serviceable oxygen masks required for the type of flight Standard’s Text A flight to be operated at flight altitudes at which the atmospheric pressure in personnel compartments will be less than 700 hPa shall not be commenced unless sufficient stored breathing oxygen is carried to supply: a) all crew members and 10 per cent of the passengers for any period in excess of 30 minutes that the pressure in compartments occupied by them will be between 700 hPa and 620 hPa; and b) the crew and passengers for any period that the atmospheric pressure in compartments occupied by them will be less than 620 hPa. A flight to be operated with a pressurized aeroplane shall not be commenced unless a sufficient quantity of stored breathing oxygen is carried to supply all the crew members and passengers, as is appropriate to the circumstances of the flight being undertaken, in the event of loss of pressurization, for any period that the atmospheric pressure in any compartment occupied by them would be less than 700 hPa. In addition, when an aeroplane is operated at flight altitudes at which the atmospheric pressure is less than 376 hPa, or which, if operated at flight altitudes at which the atmospheric pressure is more than 376 hPa and cannot descend safely within four minutes to a flight altitude at which the atmospheric pressure is equal to 620 hPa, there shall be no less than a 10-minute supply for the occupants of the passenger compartment. Prescribed safety and survival equipment that the crew or passengers are expected to use or operate at the time of an emergency shall be reliable, readily accessible and easily identified, and its method of operation shall be plainly marked. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 700 hPa in personnel compartments shall be equipped with oxygen storage and dispensing apparatus capable of storing and dispensing the oxygen supplies required in Annex 6 Part I Chapter 4.3.8.1.

Std. ref. A6-I-4.3.8.1 A6-I-4.3.8.2 A8-IIIA-8.3 A8-V-6.3 A8-IIIB-6.3 A6-I-6.7.1 Cat. 3 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B09 V 2.0 Page 159 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B09-07 B09-08 Pre-described Finding Insufficient oxygen masks for all cabin crew and 10% of passengers (and required for the type of flight) (non-pressurized flight between FL 100 and FL 130,in excess of 30 min) Automatic oxygen deploying system unserviceable (damaged/taped drop-out panels) outside MEL limits Standard’s Text An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 700 hPa but which is provided with means of maintaining pressures greater than 700 hPa in personnel compartments shall be provided with oxygen storage and dispensing apparatus capable of storing and dispensing the oxygen supplies required in Annex 6 Part I Chapter 4.3.8.2. A flight to be operated at flight altitudes at which the atmospheric pressure in personnel compartments will be less than 700 hPa shall not be commenced unless sufficient stored breathing oxygen is carried to supply: a) all crew members and 10 per cent of the passengers for any period in excess of 30 minutes that the pressure in compartments occupied by them will be between 700 hPa and 620 hPa; and b) the crew and passengers for any period that the atmospheric pressure in compartments occupied by them will be less than 620 hPa. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 700 hPa but which is provided with means of maintaining pressures greater than 700 hPa in personnel compartments shall be provided with oxygen storage and dispensing apparatus capable of storing and dispensing the oxygen supplies required in Annex 6 Part I Chapter 4.3.8.2. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 376 hPa, or which, if operated at flight altitudes at which the atmospheric pressure is more than 376 hPa, cannot descend safely within four minutes to a flight altitude at which the atmospheric pressure is equal to 620 hPa and for which the individual certificate of airworthiness is first issued on or after 9 November 1998, shall be provided with automatically deployable oxygen equipment to satisfy the requirements of Annex 6 Part I Chapter 4.3.8.2. The total number of oxygen dispensing units shall exceed the number of passenger and cabin crew seats by at least 10 per cent.

Std. ref. A6-I-6.7.2 A6-I-4.3.8.1 A6-I-6.7.1 A6-I-6.7.5 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B09 B09 V 2.0 Page 160 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B09-09 B09-10 Pre-described Finding Oxygen dispensing equipment unserviceable (low pressure, clearly overdue, damaged) and not identified as such and required for the type of flight Oxygen bottles not correctly secured Standard’s Text A flight to be operated at flight altitudes at which the atmospheric pressure in personnel compartments will be less than 700 hPa shall not be commenced unless sufficient stored breathing oxygen is carried to supply: a) all crew members and 10 per cent of the passengers for any period in excess of 30 minutes that the pressure in compartments occupied by them will be between 700 hPa and 620 hPa; and b) the crew and passengers for any period that the atmospheric pressure in compartments occupied by them will be less than 620 hPa. An aeroplane intended to be operated at flight altitudes at which the atmospheric pressure is less than 700 hPa but which is provided with means of maintaining pressures greater than 700 hPa in personnel compartments shall be provided with oxygen storage and dispensing apparatus capable of storing and dispensing the oxygen supplies required in Annex 6 Part I Chapter 4.3.8.2. Provisions shall be made in the design of the aeroplane to protect the occupants, in the event of an emergency landing, from fire and from the direct effects of deceleration forces as well as from injuries arising from the effect of deceleration forces on the aeroplane’s interior equipment. Provisions shall be made in the design of the aeroplane to protect the occupants, in the event of an emergency landing, from fire and from the direct effects of deceleration forces as well as from injuries arising from the effect of deceleration forces on the aeroplane’s interior equipment.

Std. ref. A6-I-4.3.8.1 A6-I-6.7.1 A8-IIIA-4.1.7.1 A8-IIIB-4.6.1 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B09 B09 V 2.0 Page 161 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B10-01 B10-02 Pre-described Finding Insufficient Aircraft Briefing Cards for all passengers on board Aircraft briefing cards in poor condition determined by the operator (ABC, oral briefing, video demonstration, or a combination of these methods). Therefore, briefing cards may not always be on board or may not always contain all relevant safety information, and this may not constitute a finding unless evidence is available that not all relevant information is conveyed.

provisions of the MEL.

Inspecting Instructions Note: ICAO requires that certain safety relevant information is conveyed to the passengers. The method used may be If ABCs are on board, check for their accuracy and that sufficient numbers are available. If no ABCs are on board, verify if the alternative method used conveys the required information. Note: ABC = Aircraft Briefing Cards Check the serviceability of the Fasten seat belt and Return to seat (lavatories) signs. If unserviceable, check the associated Standard’s Text An operator shall ensure that passengers are made familiar with the location and use of: a) seat belts; b) emergency exits; c) life jackets, if the carriage of life jackets is prescribed; d) oxygen dispensing equipment, if the provision of oxygen for the use of passengers is prescribed; and e) other emergency equipment provided for individual use, including passenger emergency briefing cards. An aeroplane shall be equipped with: d) means of ensuring that the following information and instructions are conveyed to passengers: 1) when seat belts are to be fastened; 2) when and how oxygen equipment is to be used if the carriage of oxygen is required; 3) restrictions on smoking; 4) location and use of life jackets or equivalent individual floatation devices where their carriage is required; and 5) location and method of opening emergency exits; An operator shall ensure that passengers are made familiar with the location and use of: a) seat belts; b) emergency exits; Std. ref. A6-I-4.2.12.1 A6-I-6.2.2 (d) A6-I-4.2.12.1 Cat. 1 1 Inspections Item Title Safety Instructions Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B10 Inspection Item B10 B10 V 2.0 Page 162 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed PDF code B10-03 Pre-described Finding Aircraft briefing cards contain inaccurate information Standard’s Text c) life jackets, if the carriage of life jackets is prescribed; d) oxygen dispensing equipment, if the provision of oxygen for the use of passengers is prescribed; and e) other emergency equipment provided for individual use, including passenger emergency briefing cards. An aeroplane shall be equipped with: d) means of ensuring that the following information and instructions are conveyed to passengers: 1) when seat belts are to be fastened; 2) when and how oxygen equipment is to be used if the carriage of oxygen is required; 3) restrictions on smoking; 4) location and use of life jackets or equivalent individual floatation devices where their carriage is required; and 5) location and method of opening emergency exits; An operator shall ensure that passengers are made familiar with the location and use of: a) seat belts; b) emergency exits; c) life jackets, if the carriage of life jackets is prescribed; d) oxygen dispensing equipment, if the provision of oxygen for the use of passengers is prescribed; and e) other emergency equipment provided for individual use, including passenger emergency briefing cards. An aeroplane shall be equipped with: d) means of ensuring that the following information and instructions are conveyed to passengers: 1) when seat belts are to be fastened; 2) when and how oxygen equipment is to be used if the carriage of oxygen is required; 3) restrictions on smoking; 4) location and use of life jackets or equivalent individual floatation devices where their carriage is required; and 5) location and method of opening emergency exits; Std. ref. A6-I-6.2.2 (d) A6-I-4.2.12.1 A6-I-6.2.2 (d) Cat. 2 Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B10 V 2.0 Page 163 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B10-04 B10-05 Pre-described Finding 'Fasten seat belt' sign(s) unserviceable 'Return to Seat' signs in lavatory unserviceable (outside MEL limits) Standard’s Text An operator shall ensure that passengers are made familiar with the location and use of: a) seat belts; b) emergency exits; c) life jackets, if the carriage of life jackets is prescribed; d) oxygen dispensing equipment, if the provision of oxygen for the use of passengers is prescribed; and e) other emergency equipment provided for individual use, including passenger emergency briefing cards. An aeroplane shall be equipped with: d) means of ensuring that the following information and instructions are conveyed to passengers: 1) when seat belts are to be fastened; 2) when and how oxygen equipment is to be used if the carriage of oxygen is required; 3) restrictions on smoking; 4) location and use of life jackets or equivalent individual floatation devices where their carriage is required; and 5) location and method of opening emergency exits; An operator shall ensure that passengers are made familiar with the location and use of: a) seat belts; b) emergency exits; c) life jackets, if the carriage of life jackets is prescribed; d) oxygen dispensing equipment, if the provision of oxygen for the use of passengers is prescribed; and e) other emergency equipment provided for individual use, including passenger emergency briefing cards. An aeroplane shall be equipped with: d) means of ensuring that the following information and instructions are conveyed to passengers: 1) when seat belts are to be fastened; 2) when and how oxygen equipment is to be used if the carriage of oxygen is required; 3) restrictions on smoking; Std. ref. A6-I-4.2.12.1 A6-I-6.2.2 (d) A6-I-4.2.12.1 A6-I-6.2.2 (d) Cat. 2 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B10 B10 V 2.0 Page 164 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B10-06 B10-07 Pre-described Finding No aircraft briefing cards on board and no other means to convey safety instructions to the passengers Aircraft briefing cards not for the correct aircraft type and/or configuration Standard’s Text 4) location and use of life jackets or equivalent individual floatation devices where their carriage is required; and 5) location and method of opening emergency exits; An operator shall ensure that passengers are made familiar with the location and use of: a) seat belts; b) emergency exits; c) life jackets, if the carriage of life jackets is prescribed; d) oxygen dispensing equipment, if the provision of oxygen for the use of passengers is prescribed; and e) other emergency equipment provided for individual use, including passenger emergency briefing cards. An aeroplane shall be equipped with: d) means of ensuring that the following information and instructions are conveyed to passengers: 1) when seat belts are to be fastened; 2) when and how oxygen equipment is to be used if the carriage of oxygen is required; 3) restrictions on smoking; 4) location and use of life jackets or equivalent individual floatation devices where their carriage is required; and 5) location and method of opening emergency exits; An operator shall ensure that passengers are made familiar with the location and use of: a) seat belts; b) emergency exits; c) life jackets, if the carriage of life jackets is prescribed; d) oxygen dispensing equipment, if the provision of oxygen for the use of passengers is prescribed; and e) other emergency equipment provided for individual use, including passenger emergency briefing cards. An aeroplane shall be equipped with: d) means of ensuring that the following information and instructions are conveyed to passengers: Std. ref. A6-I-4.2.12.1 A6-I-6.2.2 (d) A6-I-4.2.12.1 A6-I-6.2.2 (d) Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B10 B10 V 2.0 Page 165 of 217 Instructions for completing the detailed description PDF code Pre-described Finding Standard’s Text 1) when seat belts are to be fastened; 2) when and how oxygen equipment is to be used if the carriage of oxygen is required; 3) restrictions on smoking; 4) location and use of life jackets or equivalent individual floatation devices where their carriage is required; and 5) location and method of opening emergency exits; Std. ref.

Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 166 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the PDF code B11-01 B11-02 B11-03 B11-04 Pre-described Finding Cabin crew member(s) not familiar with the cabin emergency procedures Cabin crew not familiar with the location and/or operation of emergency equipment Insufficient number of cabin crew members Qualified personnel not Inspecting Instructions Check if the cabin crew composition meets the minimum crew requirements (available in the Operations Manual). Check if the cabin crew members are familiar with the cabin emergency procedures and the location and/or operation of the emergency equipment. When refuelling with passengers on board, check if qualified personnel are at the required positions (in accordance with the operations manual). Furthermore check that a two way communication system with the ground crew is established. When circumstances dictate (e.g. aircraft undergoes significant delay) check whether the cabin crew members are in compliance with the flight and duty time rules contained within the Operations Manual. Standard’s Text An operator shall establish, to the satisfaction of the State of the Operator, the minimum number of cabin attendants required for each type of aeroplane, based on seating capacity or the number of passengers carried, in order to effect a safe and expeditious evacuation of the aeroplane, and the necessary functions to be performed in an emergency or a situation requiring emergency evacuation. The operator shall assign these functions for each type of aeroplane. An operator shall establish, to the satisfaction of the State of the Operator, the minimum number of cabin attendants required for each type of aeroplane, based on seating capacity or the number of passengers carried, in order to effect a safe and expeditious evacuation of the aeroplane, and the necessary functions to be performed in an emergency or a situation requiring emergency evacuation. The operator shall assign these functions for each type of aeroplane. An operator shall establish, to the satisfaction of the State of the Operator, the minimum number of cabin attendants required for each type of aeroplane, based on seating capacity or the number of passengers carried, in order to effect a safe and expeditious evacuation of the aeroplane, and the necessary functions to be performed in an emergency or a situation requiring emergency evacuation. The operator shall assign these functions for each type of aeroplane. 4.3.7.1 An aeroplane shall not be refuelled when Std. ref. A6-I-12.1 A6-I-12.1 A6-I-12.1 A6-I-4.3.7 Cat. 2 2 3 3 Inspections Item Title Cabin crew members Std. I I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B11 Inspection Item B11 B11 B11 B11 V 2.0 Page 167 of 217 Instructions for completing the detailed description situation observed Indicate the particulars of the situation observed Describe the observed situation vs. the requirements in the OPS Manual PDF code B11-05 B11-06 Pre-described Finding at their required positions when refuelling with passengers on board No two-way communication established with the ground crew during refuelling with passengers on board Cabin Crew member not in compliance with the flight and duty time rules Standard’s Text passengers are embarking, on board or disembarking unless it is properly attended by qualified personnel ready to initiate and direct an evacuation of the aeroplane by most practical and expeditious means available. 4.3.7.2 When refuelling with passengers embarking, on board or disembarking, two-way communication shall be maintained by the aeroplane's inter-communication system or other suitable means between the ground crew supervising the refuelling and the qualified personnel on board the aeroplane. 4.3.7.1 An aeroplane shall not be refuelled when passengers are embarking, on board or disembarking unless it is properly attended by qualified personnel ready to initiate and direct an evacuation of the aeroplane by most practical and expeditious means available. 4.3.7.2 When refuelling with passengers embarking, on board or disembarking, two-way communication shall be maintained by the aeroplane's inter-communication system or other suitable means between the ground crew supervising the refuelling and the qualified personnel on board the aeroplane. An operator shall formulate rules to limit flight time and flight duty periods and for the provision of adequate rest periods for all its crew members. These rules shall be in accordance with the regulations established by the State of the Operator, or approved by that State, and included in the operations manual.

Std. ref. A6-I-4.3.7 A6-I-4.2.11.2 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B11 B11 V 2.0 for Page 168 of 217 required Instructions for completing the detailed description Indicate the particulars of the situation observed dimensions minimum PDF code B12-01 the meets opening Pre-described Finding Floor/carpet in poor condition affecting the rapid evacuation projected remaining the as long As finding.

a constitute certification, no finding should be raised. might recline, provided that no further emergency exit is immediately behind. deceleration forces or shockloads, it should be raised as a finding. However, the categorisation depends on the location of the table concerned (adjacent to an emergency exit or not). locks on tray table latches) near the emergency exits which should prevent inadvertent release of the tables during the evacuation of the aircraft. Only for those aircraft the absence of the special latches should be considered as a finding. Inspectors should therefore be particularly cautious while identifying such findings.

Inspecting Instructions Check floor/carpets/panels condition. Check if access to emergency exits impeded by baggage/seats/tables Note: Certain types of emergency exits may be oversized. Having seat rows next to such an exit, might not necessarily Note: The row of seats ahead an emergency exit must not recline, however the row adjacent to the exit (namely the ‘exit row’) Note: If the condition of the tray table latch is such that it fails to maintain the table in its upright position when it is subject to Note: Depending on the certification standards, certain aircraft types may have special table latches (one-way or recessed Standard’s Text Aeroplanes over 5700 KG for which application for certification was submitted on or after 13 June 1960 but before 2 March 2004. 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts.

Std. ref. A8-IIIA-4.1.7.2 A8-IIIB-8.4 Cat. 3 Inspections Item Title Access to emergency exits Std. I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B12 Inspection Item B12 V 2.0 Page 169 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B12-02 B12-03 B12-04 Pre-described Finding Damaged wall panel in the vicinity of emergency exit possibly obstructing the exit Tray table latches can be opened in the direction of evacuation (not recessed or special one-way lock) Access to emergency exits impeded by baggage or cargo Standard’s Text Aeroplanes over 5700 KG for which application for certification was submitted on or after 13 June 1960 but before 2 March 2004. 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: d) likely blockages of exits; Aeroplanes over 5700 KG for which application for certification was submitted on or after 13 June 1960 but before 2 March 2004. 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane.

A8-IIIB-8.4(d) A8-IIIA-4.1.7.2 Std. ref. A8-IIIA-4.1.7.2 A8-IIIB-8.4 Cat. 2 3 3 Std. I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B12 B12 B12 V 2.0 Page 170 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B12-05 B12-06 Pre-described Finding Access to emergency exits impeded by seats (total rows) Cabin crew seat does not retract automatically impeding the access to emergency exit Standard’s Text Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. Aeroplanes over 5700 KG for which application for certification was submitted on or after 13 June 1960 but before 2 March 2004. 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. Aeroplanes over 5700 KG for which application for certification was submitted on or after 13 June 1960 but before 2 March 2004. 4.1.7.2 Facilities shall be provided for the rapid evacuation A8-IIIA-4.1.7.2 Std. ref. A8-IIIB-8.4 A8-IIIB-8.4 A8-IIIA-4.1.7.2 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B12 B12 V 2.0 Page 171 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed and the details on the certification provisions PDF code B12-07 B12-08 Pre-described Finding Access to emergency exits impeded by seats (oversized seat cushions) Tray table locks can be opened in the direction of evacuation whilst certificated with special Standard’s Text of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. Aeroplanes over 5700 KG for which application for certification was submitted on or after 13 June 1960 but before 2 March 2004. 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. Aeroplanes over 5700 KG for which application for certification was submitted on or after 13 June 1960 but before 2 March 2004. 4.1.7.2 Facilities shall be provided for the rapid evacuation Std. ref. A8-IIIB-8.4 A8-IIIA-4.1.7.2 A8-IIIB-8.4 A8-IIIA-4.1.7.2 Cat. 3 3 Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B12 B12 V 2.0 Page 172 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B12-09 B12-10 Pre-described Finding locks Tray table locks fail to maintain the tables in upright position in case of deceleration, shocks (for seats not adjacent to emergency exits) Tray table locks fail to maintain the tables in upright position in case of deceleration, shocks Standard’s Text of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. Aeroplanes over 5700 KG for which application for certification was submitted on or after 13 June 1960 but before 2 March 2004. 4.1.7.2 Facilities shall be provided for the rapid evacuation of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts. Aeroplanes over 5700 KG for which application for certification was submitted on or after 13 June 1960 but before 2 March 2004. 4.1.7.2 Facilities shall be provided for the rapid evacuation Std. ref. A8-IIIB-8.4 A8-IIIA-4.1.7.2 A8-IIIB-8.4 A8-IIIA-4.1.7.2 Cat. 1 3 Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B12 B12 V 2.0 Page 173 of 217 Instructions for completing the detailed description PDF code Pre-described Finding (for seats adjacent to emergency exits) Standard’s Text of the aeroplane in conditions likely to occur following an emergency landing. Such facilities shall be related to the passenger and crew capacity of the aeroplane. Aeroplanes over 5700 KG for which application for certification was submitted on or after 2 March 2004. The aeroplane shall be equipped with sufficient emergency exits to allow maximum opportunity for cabin evacuation within an appropriate time period. Items to be considered shall include: a) number of seats and seating configuration; b) number, location and size of exits; c) marking of exits and provision of instructions for use; d) likely blockages of exits; e) operation of exits; and f) positioning and weight of evacuation equipment at exits, e.g. slides and rafts.

Std. ref. A8-IIIB-8.4 Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item V 2.0 Page 174 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B13-01 B13-02 B13-03 B13-04 B13-05 Pre-described Finding Hard or heavy baggage stored in open hat-racks Baggage stowed in unserviceable overhead bins (although marked as unserviceable) Oversized baggage transported in the cabin not adequately secured Baggage not stowed securely Overhead bins loaded in excess of the placarded weight limitation Inspecting Instructions Check storage of baggage (including heavy and oversized baggage). Standard’s Text The operator shall ensure that all baggage carried onto an aeroplane and taken into the passenger cabin is adequately and securely stowed. The operator shall ensure that all baggage carried onto an aeroplane and taken into the passenger cabin is adequately and securely stowed. The operator shall ensure that all baggage carried onto an aeroplane and taken into the passenger cabin is adequately and securely stowed. The operator shall ensure that all baggage carried onto an aeroplane and taken into the passenger cabin is adequately and securely stowed. The operator shall ensure that all baggage carried onto an aeroplane and taken into the passenger cabin is adequately and securely stowed.

Std. ref. A6-I-4.8 A6-I-4.8 A6-I-4.8 A6-I-4.8 A6-I-4.8 Cat. 3 3 3 3 3 Inspections Item Title Safety of passenger baggage Std. I I I I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B13 Inspection Item B13 B13 B13 B13 B13 V 2.0 Page 175 of 217 Instructions for completing the detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code B14-01 B14-02 Pre-described Finding Insufficient seats for all passengers on board Seat(s)/baby berth(s) not certified to be installed on board of aircraft Inspecting Instructions Check number of available seats. Standard’s Text An aeroplane shall be equipped with: c) 1) a seat or berth for each person over an age to be determined by the State of the Operator. An aeroplane shall be equipped with: c) 1) a seat or berth for each person over an age to be determined by the State of the Operator.

Std. ref. A6-I-6.2.2(c)(1) A6-I-6.2.2(c)(1) Cat. 3 3 Inspections Item Title Seat capacity Std. I I

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item B14 Inspection Item B14 B14 V 2.0 Page 176 of 217 completing the Instructions for detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code C01-01 C01-02 C01-03 Pre-described Finding Markings and/or placards required by the manufacturer not applied or unreadable Aircraft very dirty affecting the ability to inspect it Break-in point markings (if applied) faded or incorrectly marked Inspecting Instructions Standard’s Text corrosion; cleanliness (related to the ability to inspect the aircraft); presence of ice, snow, frost; legibility of markings. Loose or missing fasteners and rivets Presence and condition of the antennas Presence and condition of the static dischargers Condition and functionality of the exterior lights etc.

is considered low. Therefore, such non-compliance should be recorded as a General Remark (cat G) only. should be according to a certain format). required only by the manufacturer. (according to the MEL). Unserviceable lights, not required for the type of flight, should be reported as a General Remark only.

        Check general condition of the airframe: Note: Although missing underwing registrations are a non-compliance with international requirements, the safety relevance Note: markings may be in languages other than English. Note: ICAO does not require that break-in points need to be marked (however: if such markings are being used, they Note: When inspecting markings and placards, inspectors should differentiate between those required by ICAO and those Note: Before raising a finding, the inspector should make sure that the affected light(s) are required for the type of flight The structure shall be protected against deterioration or loss of strength in service due to weathering, corrosion, abrasion or other causes, which could pass unnoticed, taking into account the maintenance the aeroplane will receive. If areas of the fuselage suitable for break-in by rescue crews in emergency are marked on an aeroplane such areas shall be marked as shown below (see figure following). The colour of the markings shall be red or yellow, and if necessary Std. ref.

A8-IIIA-4.1.4 A8-IIIB-4.1.5 A8-V-4.1.5 A6-I-6.2.4.1 Cat.

1 1 2 Inspections Item Title Std.

General external condition M I I

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 C01 C01 C01 C01 V 2.0 Page 177 of 217 Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed C01-04 C01-05 C01-06 C01-07 C01-08 C01-09 C01-10 Paint damage with exposed composite Poor condition of de-icing system Safety markings not applied or unreadable Minor corrosion Significant corrosion Aircraft lights unserviceable for night operations (outside MEL limits) Fasteners/rivets loose or missing outside limits, but dispatch allowed according to AMM/SRM, and not assessed nor recorded.

they shall be outlined in white to contrast with the background. The structure shall be protected against deterioration or loss of strength in service due to weathering, corrosion, abrasion or other causes, which could pass unnoticed, taking into account the maintenance the aeroplane will receive. The structure shall be protected against deterioration or loss of strength in service due to weathering, corrosion, abrasion or other causes, which could pass unnoticed, taking into account the maintenance the aeroplane will receive. Markings and placards or instructions shall be provided to give any information that is essential to the ground crew in order to preclude the possibility of mistakes in ground servicing (e.g. towing, refuelling) that could pass unnoticed and that could jeopardize the safety of the aeroplane in subsequent flights. The structure shall be protected against deterioration or loss of strength in service due to weathering, corrosion, abrasion or other causes, which could pass unnoticed, taking into account the maintenance the aeroplane will receive. The structure shall be protected against deterioration or loss of strength in service due to weathering, corrosion, abrasion or other causes, which could pass unnoticed, taking into account the maintenance the aeroplane will receive. All aeroplanes, when operated at night shall be equipped with: b) the lights required by Annex 2 for aircraft in flight or operating on the movement area of an aerodrome; c) two landing lights; A8-IIIA-4.1.4 A8-IIIB-4.1.5 A8-V-4.1.5 A8-IIIA-4.1.4 A8-IIIB-4.1.5 A8-V-4.1.5 A8-IIIA-9.6.2 A8-IIIB-7.6.2 A8-V-7.6.2 A8-IIIA-4.1.4 A8-IIIB-4.1.5 A8-V-4.1.5 A8-IIIA-4.1.4 A8-IIIB-4.1.5 A8-V-4.1.5 A6-I-6.10 2 2 2 1 2 3 2 I I I I I I M

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 C01 C01 C01 C01 C01 C01 C01 V 2.0 Page 178 of 217 Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed C01-11 C01-12 C01-13 C01-14 C01-15 C01-16 C01-17 Fasteners or rivets loose or missing outside SRM/AMM limits Static discharger(s) missing or damaged outside MEL/AMM/CDL limits Antenna(s) missing or damaged outside AMM/MEL/CDL limits No intentions to request appropriate de-icing treatment No appropriate de/anti-icing treatment with ground icing conditions Pressure port(s) damaged or contaminated Tail skid wear outside AMM limits A flight to be planned or expected to operate in suspected or known ground icing conditions shall not take off unless the aeroplane has been inspected for icing and, if necessary, has been given appropriate de-icing/anti-icing treatment. Accumulation of ice or other naturally occurring contaminants shall be removed so that the aeroplane is kept in an airworthy condition prior to take-off. A flight to be planned or expected to operate in suspected or known ground icing conditions shall not take off unless the aeroplane has been inspected for icing and, if necessary, has been given appropriate de-icing/anti-icing treatment. Accumulation of ice or other naturally occurring contaminants shall be removed so that the aeroplane is kept in an airworthy condition prior to take-off.

A6-I-4.3.5.4 A6-I-4.3.5.4 3 3 3 3 3 3 3 M M M I I M M

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 C01 C01 C01 C01 C01 C01 C01 V 2.0 detailed description Page 179 of 217 completing the Instructions for Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code C02-01 C02-02 C02-03 C02-04 C02-05 C02-06 .

Pre-described Finding Inspecting Instructions Bonding wires broken or missing (outside AMM limits) Door handle(s), lever(s), access panel(s) not flush Door operation instructions missing or unclear Cargo door lock inspection glasses blind and no other mean to verify locking position(s) Door seal damaged outside AMM/CDL limits Door(s) unserviceable outside AMM/CDL limits Standard’s Text presence and condition of bonding wires; door external markings, operation instructions; condition of doors, hatches and associated seals.

   Note: only those doors which can be opened from the outside need external markings Check for: Markings and placards or instructions shall be provided to give any information that is essential to the ground crew in order to preclude the possibility of mistakes in ground servicing (e.g. towing, refuelling) that could pass unnoticed and that could jeopardize the safety of the aeroplane in subsequent flights.

Std. ref.

A8-IIIA-9.6.2 A8-IIIB-7.6.2 A8-V-7.6.2 Cat.

3 2 2 3 3 3 Inspections Item Title Std.

Doors and hatches M M I M M M

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 C02 C02 C02 C02 C02 C02 C02 V 2.0 Page 180 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code C03-01 C03-02 C03-03 C03-04 C03-05 Pre-described Finding Bonding wires broken or missing (outside limits) Hydraulic leak outside limits Static discharger(s) missing (outside MEL/AMM/CDL limits) Flight controls unserviceable Fasteners or rivets loose or missing outside AMM/SRM limits Inspecting Instructions Standard’s Text Check external Flight Controls. Check for hydraulic leakage. Check presence and condition of the static dischargers. Check presence and condition of bonding wires. Any failure to maintain an aircraft in an airworthy condition as defined by the appropriate airworthiness requirements shall render the aircraft ineligible for operation until the aircraft is restored to an airworthy condition.

Std. ref.

A8-II-3.5 Cat.

3 3 3 3 3 Inspections Item Title Std.

Flight controls M M M I M

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item Inspection Item C03 C03 C03 C03 C03 C03 V 2.0 Page 181 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code C04-01 C04-02 C04-03 C04-04 C04-05 C04-06 C04-07 C04-08 C04-09 C04-10 C04-11 C04-12 Pre-described Finding Inspecting Instructions Brake wear indicator pin(s) missing (at least one pin remaining) Tyre inflation valve(s) cap missing Brake assembly bleed valve dust cap(s) missing Brake worn beyond limits but dispatch allowed according to AMM (not assessed nor recorded) Tyre(s) worn beyond limits but dispatch allowed according to AMM (not assessed nor recorded) Brake(s) unserviceable and not recorded Damaged or missing parts outside limits (i.e. bolts, heat sensors) Leaking hydraulic braking system (outside limits) Nose landing gear wheel snubbers worn outside limits Tyre pressure obviously outside limits Tyre(s) unserviceable (worn or damaged) and not recorded Rim damaged outside of limits Standard’s Text AMM limits.

Inspect wheels and tyres for damage and wear. When possible, check for correct tyre pressure. Check the condition of the braking system. Check the condition of the landing gear snubbers. Note: some aircraft manufacturers may approve a certain amount of flights with tires or brakes worn out or damaged beyond Std. ref.

Cat.

1 1 1 2 2 3 3 3 3 3 3 3 Inspections Item Title Std.

Wheels, tyres and brakes M M M M M M M M M M M M

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 C04 C04 C04 C04 C04 C04 C04 C04 C04 C04 C04 C04 C04 V 2.0 Page 182 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate what marking were missing/unreadable, including the appropriate AMM/SRM reference Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code C05-01 C05-02 C05-03 C05-04 C05-05 C05-06 C05-07 C05-08 C05-09 C05-10 Pre-described Finding Markings and/or placards required by the manufacturer not applied or unreadable Safety lock pin(s) missing or defective Undercarriage dirty affecting the ability to inspect it and detect potential leakages Gear strut valve cap(s) missing Water/debris deflectors damaged or missing outside AMM/CDL Lines, hoses electrical wiring chafed Safety markings not applied or unreadable Significant signs of corrosion Seepage/leakage outside limits Strut pressure outside limit Inspecting Instructions Standard’s Text required only by the manufacturer. Check for condition, lubrication, corrosion, leaks, damage and inappropriate strut extension.

Check presence and condition of the water/debris deflectors (if required to be installed). Check skids/floats for obvious damages. Check for presence and legibility of inspection markings/placards. Note: When inspecting markings and placards, inspectors should differentiate between those required by ICAO and those Markings and placards or instructions shall be provided to give any information that is essential to the ground crew in order to preclude the possibility of mistakes in the ground servicing (e.g. towing, refuelling) that could pass unnoticed and that could jeopardize the safety of the aeroplane in subsequent flights Std. ref.

A8-IIIA-9.6.2 A8-IIIB-7.6.2 A8-V-7.6.2 Cat.

1 1 1 1 3 2 2 2 3 3 Inspections Item Title Std.

Undercarriage, skids/floats M M M M M M I M M M

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 C05 C05 C05 C05 C04 C05 C05 C05 C05 C05 C05 V 2.0 Page 183 of 217 completing the Instructions for detailed description Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code C06-01 C06-02 C06-03 C06-04 C06-05 C06-06 C06-07 Pre-described Finding Inspecting Instructions Wheel well dirty affecting the ability to Landing gear door(s) damaged outside Obvious lack of lubrication of hinge(s), Bonding wires broken or missing Significant signs of corrosion Landing gear emergency spring lock(s) Seepage/leakage outside limits inspect it SRM limits actuator(s) (outside limits) broken/unserviceable Standard’s Text Check for lubrication, leakage & corrosion. Check for lubrication, leakage & corrosion and wear on door fittings and hinges. Check for presence and condition of bonding wires. Check for cleanliness and damage.

Std. ref.

Cat.

1 3 2 3 3 3 3 Inspections Item Title Std.

Wheel well M M M M M M M

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 C06 C06 C06 C06 C06 C06 C06 C06 V 2.0 Page 184 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate what marking were missing/unreadable, including the appropriate AMM/SRM reference Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code C07-01 C07-02 C07-03 C07-04 C07-05 C07-06 C07-07 C07-08 C07-09 Pre-described Finding Markings and/or placards required by the manufacturer not applied or unreadable Safety markings not applied or unreadable Significant damage in the intake and exhaust area Damage (dents, nicks, cracks) outside limits Intake acoustic liners damaged outside AMM limits Leakage (oil, fuel, hydraulics) outside AMM limits Panels/fairings/cowlings/handles misaligned or not flush outside AMM limits Screws/rivets loose or missing, outside limits Thrust reverser/blocker doors not fully stowed Inspecting Instructions Standard’s Text dents and loose/missing fasteners; LPT/LPC blades (where visible), obvious damage to sensors; cracks; panels are aligned and handles are flushed; unusual damage and leaks; the condition of the thrust reverser; the condition of the Intake acoustic liners; presence and legibility of the markings and placards.

required only by the manufacturer.

        Leak Check for: Note: When inspecting markings and placards, inspectors should differentiate between those required by ICAO and those Markings and placards or instructions shall be provided to give any information that is essential to the ground crew in order to preclude the possibility of mistakes in the ground servicing (e.g. towing, refuelling) that could pass unnoticed and that could jeopardize the safety of the aeroplane in subsequent flights Std. ref.

A8-IIIA-9.6.2 A8-IIIB-7.6.2 A8-V-7.6.2 Cat.

1 2 2 3 3 3 3 3 3 Inspections Item Title Std.

Powerplant and pylon M I M M M M M M M

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 C07 C07 C07 C07 C07 C07 C07 C07 C07 C07 V 2.0 Page 185 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed PDF code C08-01 Pre-described Finding Inspecting Instructions Fan blade(s) damaged beyond AMM limit Standard’s Text Check for FOD damage, cracks, cuts, corrosion, erosion, etc. .

Std. ref.

Cat.

Inspections Item Title Std.

Fan blades M

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 C08 C08 V 2.0 Page 186 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code C09-01 C09-02 Pre-described Finding Propeller de-icing system unserviceable (outside MEL/AMM limits) Propeller(s) damaged beyond AMM limits Inspecting Instructions Standard’s Text Check for corrosion, looseness of blades in hub, stone damage, etc. . Check the de-ice boots for damage (where fitted).

Std. ref.

Cat.

3 3 Inspections Item Title Std.

Propellers, rotors (main/tail) M M

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item Inspection Item C09 C09 C09 V 2.0 Page 187 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code C10-01 C10-02 C10-03 Pre-described Finding No information about temporary repairs Previous repair in poor condition Repairs obviously not carried out in accordance with the applicable AMM/SRM Inspecting Instructions Standard’s Text However, the PIC has to have the knowledge of the status of the temporary repairs in order to be satisfied that the aeroplane remains airworthy.

Check for repairs of unusual design or poorly performed. Note: There is no obligation to keep information on board regarding temporary repairs (e.g. on the dent & buckle chart). A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in-command is satisfied that: a) the aeroplane is airworthy; Std. ref.

A6-I-4.3.1(a) Cat.

2 2 3 Inspections Item Title Std.

Obvious repairs I M M

SAFA Ramp Inspection Procedures Guidance material

SAFA Coordination Section © European Aviation Safety Agency, 2012 Inspection Item Inspection Item C10 C10 C10 C10 V 2.0 Page 188 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed PDF code C11-01 Pre-described Finding Structural damage affecting the airworthiness of the aircraft Inspecting Instructions Standard’s Text Check for un-assessed and un-recorded damage including corrosion, lightning strike damage, bird strikes etc. . Check that any damage is observed, assessed, and possibly recorded on a damage chart/buckle & dent chart.

Std. ref.

Cat.

Inspections Item Title Std.

Obvious unrepaired damage M

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 C11 C11 V 2.0 Page 189 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code C12-01 C12-02 Pre-described Finding Leakage outside limits Servicing doors/panels, drains blocked by ice or other debris Inspecting Instructions Standard’s Text inspection items.

Check for fuel leaks, hydraulic leaks and (if applicable) toilet liquid leaks (blue ice). Note: Leakages identified when inspecting C03, C04, C05, C06 and C07 should be reported as findings under those Std. ref.

Cat.

3 3 Inspections Item Title Std.

Leakage M M

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 C12 C12 C12 V 2.0 detailed description Page 190 of 217 completing the Instructions for Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the PDF code D01-01 D01-02 D01-03 D01-04 D01-05 Pre-described Finding Minor defects with limited effect on safety Equipment installations obviously not in compliance with Annex 8, Part IIIA/B, Chapter 4 Safety markings not applied or unreadable Cargo bay smoke detection test fail or outside MEL limits Blow-out panels pushed, damaged or missing (outside AMM/MEL Inspecting Instructions Standard’s Text Check the general condition of cargo compartment. Check lighting, fire protection, detection & extinguishing system (if appropriate). Check side wall and overhead (blow-out) panels, smoke detectors, smoke barrier/curtain. Check the presence and condition of cargo barrier/dividing nets. Under all anticipated operating conditions, the aeroplane shall not possess any feature or characteristic that renders it unsafe. 1.5.1 Compliance with the appropriate airworthiness requirements shall be based on evidence either from tests, calculations, or calculations based on tests, provided that in each case the accuracy achieved will ensure a level of airworthiness equal to that which would be achieved were direct tests conducted. 1.5.2 The tests of 1.5.1 shall be such as to provide reasonable assurance that the aeroplane, its components and equipment are reliable and function correctly under the anticipated operating conditions. Markings and placards or instructions shall be provided to give any information that is essential to the ground crew in order to preclude the possibility of mistakes in ground servicing (e.g. towing, refuelling) that could pass unnoticed and that could jeopardize the safety of the aeroplane in subsequent flights. Any failure to maintain an aircraft in an airworthy condition as defined by the appropriate Std. ref.

A8-IIIA-1.4, A8-IIIB-1.3 A8-IIIA-1.5, A8-IIIB-1.4 A8-IIIA-9.6.2 A8-IIIB-7.6.2 A8-V-7.6.2 A8-II-3.5 Cat.

1 2 2 3 3 Inspections Item Title Std.

General condition of cargo compartment M I I M I

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D01 D01 D01 D01 D01 D01 V 2.0 detailed description Page 191 of 217 completing the Instructions for Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed situation observed PDF code D01-06 D01-07 D01-08 D01-09 D01-10 D01-11 D01-12 Pre-described Finding limits) Damage to panelling and/or lining outside limits Unserviceable fire extinguishing system and the affected cargo compartment is used Floor locks unserviceable outside MEL limits (with cargo) No or unserviceable required barrier net No smoke barrier/curtain (if applicable) Structural or floor damage outside AMM/SRM limits Cargo compartment (s) not equipped with fire suppression systems Standard’s Text ) each cargo compartment accessible to a crew airworthiness requirements shall render the aircraft ineligible for operation until the aircraft is restored to an airworthy condition Any failure to maintain an aircraft in an airworthy condition as defined by the appropriate airworthiness requirements shall render the aircraft ineligible for operation until the aircraft is restored to an airworthy condition Any failure to maintain an aircraft in an airworthy condition as defined by the appropriate airworthiness requirements shall render the aircraft ineligible for operation until the aircraft is restored to an airworthy condition Any failure to maintain an aircraft in an airworthy condition as defined by the appropriate airworthiness requirements shall render the aircraft ineligible for operation until the aircraft is restored to an airworthy condition Fire suppression. For aeroplanes for which the application for certification was submitted on or after 12 March 2000, cargo compartment fire suppression systems, including their extinguishing agents, shall be designed so as to take into account a sudden and extensive fire such as could be caused by an explosive or incendiary device or dangerous goods. 1 member in a passenger-carrying aeroplane shall be equipped with a fire suppression system; Std. ref.

A8-II-3.5 A8-II-3.5 A8-II-3.5 A8-IIIA- 4.1.6.(g) A8-IIIB-4.2 (g) Cat.

3 3 3 3 3 3 3 Std.

M I M M I I I

SAFA Ramp Inspection Procedures Guidance material

Item Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D01 D01 D01 D01 D01 D01 D01 V 2.0 detailed description Page 192 of 217 completing the Instructions for Indicate the particulars of the situation observed PDF code D01-13 Pre-described Finding Cargo compartment lighting damaged outside AMM/MEL limits Standard’s Text 2) each cargo compartment not accessible to a crew member shall be equipped with a built-in fire detection system and a built-in fire starvation or suppression system; and 3) cargo compartment fire suppression systems, including their extinguishing agents, shall be designed so as to take into account a sudden and extensive fire such as could be caused by an explosive or incendiary device or dangerous goods.

Std. ref.

Cat.

Std.

M

SAFA Ramp Inspection Procedures Guidance material

Item Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D01 V 2.0 Page 193 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code D02-01 D02-02 D02-03 D02-04 Pre-described Finding Incorrect or incomplete information in NOTOC, not concerning CAO packages Incorrect or incomplete information in NOTOC, concerning CAO packages CAO-cargo (Cargo Aircraft Only) carried on passenger flights Damaged and/or leaking packages/overpacks containing DG Standard’s Text Inspecting Instructions If dangerous good are on board, check that the pilot has received appropriate notification. Check that the OPS Manual includes relevant information as required by ICAO Annex 18 (The Safe Transport of Dangerous Goods by Air). Note: if a finding is raised on this point, report it under A04 – Manuals. Check that Technical Instructions as per ICAO Doc. 9284 are applied. The following subjects, in particular, could be checked to assess the compliance with the ICAO Doc 9284: stowage, packaging, labelling, securing, and segregation. Check that Dangerous Goods are stowed, packaged and labelled in accordance with the Technical Instructions (ICAO Doc. 9284). Check that any DG contamination has been removed. If the Transportation of DG is not in compliance with the Ops Spec, report it under A10. Check, when required, the crew access to the cargo area in case of transportation of CAO goods. The operator of an aircraft in which dangerous goods are to be carried shall provide the pilot-in- command as early as practicable before departure of the aircraft with written information as specified in the Technical Instructions. The operator of an aircraft in which dangerous goods are to be carried shall provide the pilot-in- command as early as practicable before departure of the aircraft with written information as specified in the Technical Instructions. Packages of dangerous goods bearing the “Cargo aircraft only” label shall be loaded in accordance with the provisions in the Technical Instructions. 8.4.1 Packages and overpacks containing dangerous goods and freight containers containing radioactive materials shall be inspected for evidence of leakage or damage before loading on an aircraft or into a unit load device. Leaking or damaged packages, overpacks or freight containers shall not be loaded on an aircraft. 8.4.2 A unit load device shall not be loaded aboard an aircraft unless the device has been Std. ref.

A18-9.1 A18-9.1 A18-8.9 A18-8.4 Cat.

2 3 3 3 Inspections Item Title Std.

Dangerous Goods I I I I

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D02 D02 D02 D02 D02 V 2.0 Page 194 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code D02-05 D02-06 Pre-described Finding Dangerous Goods not correctly loaded and/or secured DG label incorrect or missing Standard’s Text inspected and found free from any evidence of leakage from, or damage to, any dangerous goods contained therein. 8.4.3 Where any package of dangerous goods loaded on an aircraft appears to be damaged or leaking, the operator shall remove such package from the aircraft, or arrange for its removal by an appropriate authority or organization, and thereafter shall ensure that the remainder of the consignment is in a proper condition for transport by air and that no other package has been contaminated. 8.4.4 Packages or overpacks containing dangerous goods and freight containers containing radioactive materials shall be inspected for signs of damage or leakage upon unloading from the aircraft or unit load device. If evidence of damage or leakage is found, the area where the dangerous goods or unit load device were stowed on the aircraft shall be inspected for damage or contamination. When dangerous goods subject to the provisions contained herein are loaded in an aircraft, the operator shall protect the dangerous goods from being damaged, and shall secure such goods in the aircraft in such a manner that will prevent any movement in flight which would change the orientation of the packages. For packages containing radioactive materials, the securing shall be adequate to ensure that the separation requirements of 8.7.3 are met at all times An operator shall not accept dangerous goods for transport by air: a) unless the dangerous goods are accompanied by a completed dangerous goods transport document, except where the Technical Instructions indicate that such a document is not required; and Std. ref.

A18-8.8 A18-8.1 Cat.

3 3 Std.

I I

SAFA Ramp Inspection Procedures Guidance material

Item Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D02 D02 V 2.0 Page 195 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code D02-07 D02-08 Pre-described Finding Required identification tag not properly filled in or partly invisible (no CAO packages inside) Required identification tag missing (CAO packages inside) Standard’s Text b) until the package, overpack or freight container containing the dangerous goods has been inspected in accordance with the acceptance procedures contained in the Technical Instructions. • 2.7.1 Each unit load device containing dangerous goods which require a class hazard label must clearly display on its exterior an indication that dangerous goods are contained within the unit load device, unless those hazard class labels are themselves visible. • 2.7.2 This indication must be provided by attaching to the unit load device an identification tag having a border of prominent red hatchings on both sides and the minimum dimensions of 148mmx 210 mm. The primary and subsidiary hazard class(es) or division(s) numbers of such dangerous goods must be clearly marked on this tag. • 2.7.3 If the unit load device contains packages bearing “Cargo aircraft only” label, either that label must be visible or the tag must indicate that the unit load device can only be loaded on a cargo aircraft. • 2.7.4 The tag must be removed from the unit load device immediately after the dangerous goods have been unloaded. • 2.7.1 Each unit load device containing dangerous goods which require a class hazard label must clearly display on its exterior an indication that dangerous goods are contained within the unit load device, unless those hazard class labels are themselves visible. • 2.7.2 This indication must be provided by attaching to the unit load device an identification tag having a border of prominent red hatchings on both sides and the minimum dimensions of 148mmx 210 mm. The primary and subsidiary Std. ref.

DOC 9284 (Part 7) DOC 9284 (Part 7) Cat.

2 3 Std.

I I

SAFA Ramp Inspection Procedures Guidance material

Item Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D02 D02 V 2.0 Page 196 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code D02-09 D02-10 Pre-described Finding Dangerous goods carried as limited quantities or excepted quantities but limits exceeded Dangerous goods not packed in accordance with proper packing instructions Standard’s Text hazard class(es) or division(s) numbers of such dangerous goods must be clearly marked on this tag. • 2.7.3 If the unit load device contains packages bearing “Cargo aircraft only” label, either that label must be visible or the tag must indicate that the unit load device can only be loaded on a cargo aircraft. • 2.7.4 The tag must be removed from the unit load device immediately after the dangerous goods have been unloaded. 4.1.1 Limited quantities of dangerous goods may only be carried in accordance with the limitations and provisions of this chapter and must meet all the applicable requirements of the Technical Instructions unless otherwise provided for below. 4.1.3 The limitations and provisions of this chapter for the transport of dangerous goods in limited quantities apply equally to both passenger and cargo aircraft. 4.3.1 The net quantity per package must not exceed the quantity specified in column 11 of Table 3-1 against the packing instruction number identified by the prefix letter “Y” in column 10. 4.3.2 The gross mass per package must not exceed 30 kg. 5.1.2 Dangerous goods which may be carried as excepted quantities in accordance with this chapter are shown in column 9 of the dangerous goods list by means of an alphanumeric code as indicated in Table 3-3 (…) Dangerous goods shall be packed in accordance with the provisions of this chapter and as provided for in the Technical Instructions. 1.1.1 Dangerous goods must be packed in good quality packagings, which must be strong enough to withstand the shocks and loadings normally encountered during transport, including Std. ref.

DOC 9284 (Part 3) A18-5.1 DOC 9284 (Part 4) Cat.

3 3 Std.

I I

SAFA Ramp Inspection Procedures Guidance material

Item Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D02 D02 V 2.0 Page 197 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code D02-11 D02-12 Pre-described Finding DG not stowed and/or separated in accordance with the Technical Instructions Hazardous and/or radioactive contamination not removed Standard’s Text removal from a pallet, unit load device or overpack for subsequent manual or mechanical handling. Packagings must be constructed and closed so as to prevent any loss of contents when prepared for transport, which may be caused under normal conditions of transport, by vibration, or by changes in temperature, humidity or pressure (resulting from altitude, for example). Packagings (including inner packagings and receptacles) must be closed in accordance with the information provided by the manufacturer. No dangerous residue must adhere to the outside of packages during transport. These provisions apply, as appropriate, to new, reused, reconditioned or re-manufactured packagings. Packages and overpacks containing dangerous goods and freight containers containing radioactive materials shall be loaded and stowed on an aircraft in accordance with the provisions of the Technical Instructions. 8.7.1 Packages containing dangerous goods which might react dangerously one with another shall not be stowed on an aircraft next to each other or in a position that would allow interaction between them in the event of leakage. 8.7.2 Packages of toxic and infectious substances shall be stowed on an aircraft in accordance with the provisions of the Technical Instructions. 8.7.3 Packages of radioactive materials shall be stowed on an aircraft so that they are separated from persons, live animals and undeveloped film, in accordance with the provisions in the Technical Instructions. 8.6.1 Any hazardous contamination found on an aircraft as a result of leakage or damage to dangerous goods shall be removed without delay. 8.6.2 An aircraft which has been contaminated Std. ref.

A18-8.3 A18-8.7 A18-8.6 Cat.

3 3 Std.

I I

SAFA Ramp Inspection Procedures Guidance material

Item Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D02 D02 V 2.0 Page 198 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code D02-13 D02-14 D02-15 D02-16 D02-17 Pre-described Finding Required NOTOC missing DG carried in the cabin or on the flight deck not permitted by the provisions of the technical instructions No access to DG packages labelled “Cargo aircraft only” where required Transport of forbidden dangerous goods Dangerous goods not accompanied by shipper's declaration when so required Standard’s Text by radioactive materials shall immediately be taken out of service and not returned to service until the radiation level at any accessible surface and the non-fixed contamination are not more than the values specified in the Technical Instructions. The operator of an aircraft in which dangerous goods are to be carried shall provide the pilot-in- command as early as practicable before departure of the aircraft with written information as specified in the Technical Instructions. Dangerous goods shall not be carried in an aircraft cabin occupied by passengers or on the flight deck of an aircraft, except in circumstances permitted by the provisions of the Technical Instructions. Packages of dangerous goods bearing the “Cargo aircraft only” label shall be loaded in accordance with the provisions in the Technical Instructions. The dangerous goods described hereunder shall be forbidden on aircraft unless exempted by the States concerned under the provisions of 2.1 or unless the provisions of the Technical Instructions indicate they may be transported under an approval granted by the State of Origin: a) dangerous goods that are identified in the Technical Instructions as being forbidden for transport in normal circumstances; and b) infected live animals. Articles and substances that are specifically identified by name or by generic description in the Technical Instructions as being forbidden for transport by air under any circumstances shall not be carried on any aircraft. An operator shall not accept dangerous goods for transport by air: a) unless the dangerous goods are Std. ref.

A18-9.1 A18-8.5 A18-8.9 A18-4.2 A18-4.3 A18-8.1(a) Cat.

3 3 3 3 3 Std.

I I I I I

SAFA Ramp Inspection Procedures Guidance material

Item Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D02 D02 D02 D02 D02 V 2.0 Page 199 of 217 description Instructions for completing the detailed PDF code Pre-described Finding Standard’s Text accompanied by a completed dangerous goods transport document, except where the Technical Instructions indicate that such a document is not required; Std. ref.

Cat.

Std.

SAFA Ramp Inspection Procedures Guidance material

Item Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 V 2.0 Page 200 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code D03-01 D03-02 D03-03 D03-04 D03-05 Pre-described Finding Minor damage to lashing, tie-down equipment, pallets, lock assemblies and/or containers Incomplete equipment like lashing, tie-down equipment, pallets, lock assemblies and/or containers Cargo Area not used in accordance with classification Cargo not correctly secured and restrained in all directions Major damage to lashing, tie-down equipment, pallets, lock assemblies and/or containers affecting the structural integrity and Inspecting Instructions Standard’s Text nets and the restraining of the cargo is achieved by the containment in the compartment itself (e.g. cargo bulkhead compartment of regional turboprops). If the type certification does not prescribe the presence of nets, their absence should not constitute a finding.

Check that loads are properly distributed (floor limits, height limits, pallets and containers maximum gross weight). Note: Not all aircraft have load height restrictions. Check that flight/fly-away kit and spare wheels are correctly secured. Check that cargo is correctly secured. Check the condition of cargo containers, pallets, lock assemblies and lashing nets. Check the condition of the cargo compartment dividing nets. Note: Although in most cases cargo is restrained using cargo nets, in certain cases aircraft have been certified without such A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in- command is satisfied that: e) any load carried is properly distributed and safely secured A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in- command is satisfied that: e) any load carried is properly distributed and safely secured A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in- command is satisfied that: e) any load carried is properly distributed and safely secured A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in- command is satisfied that: e) any load carried is properly distributed and safely secured A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in- command is satisfied that: e) any load carried is properly distributed and safely secured Std. ref.

A6-I-4.3.1e A6-I-4.3.1e A6-I-4.3.1e A6-I-4.3.1e A6-I-4.3.1e Cat.

1 2 3 3 3 Inspections Item Title Std.

Safety of cargo on board I I I I I

SAFA Ramp Inspection Procedures Guidance material

Item Item Inspection Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D03 D03 D03 D03 D03 D03 V 2.0 Page 201 of 217 description Instructions for completing the detailed Indicate the particulars of the situation observed Indicate the particulars of the situation observed PDF code D03-06 D03-07 Pre-described Finding their intended function Dividing net or protection net damaged beyond AMM limits Load distribution/load limit (floor and/or height) exceeded Standard’s Text A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in- command is satisfied that: e) any load carried is properly distributed and safely secured A flight shall not be commenced until flight preparation forms have been completed certifying that the pilot-in- command is satisfied that: e) any load carried is properly distributed and safely secured Std. ref.

A6-I-4.3.1e A6-I-4.3.1e Cat.

3 3 Std.

I I

SAFA Ramp Inspection Procedures Guidance material

Item Inspection SAFA Coordination Section © European Aviation Safety Agency, 2012 D03 D03 V 2.0 Page 202 of 217 description Instructions for completing the detailed Pre-described Finding Inspecting Instructions Standard’s Text Check (if appropriate) for any general item which may have a direct relation with the safety of the aircraft or its occupants.

Std. ref.

Cat.

Inspections Item Title Std.

General

SAFA Ramp Inspection Procedures Guidance material

Inspection Item Inspection Item SAFA Coordination Section © European Aviation Safety Agency, 2012 E01 E01

SAFA Ramp Inspection Procedures

Guidance material

Appendix 2

Instructions for the completion of the SAFA Ramp inspection report

(Appendix 1 to the Commission Directive 2008/49/EC) General instructions:  If any airport code, operator code or aircraft type is missing, do not use temporary codes or existing but incorrect Codes. Contact the SAFA coordination department of the Agency and the requested code will be added after verification.

 In the column “Checked” of the checklist, only mark those items which are inspected.

Be careful not to mark e.g. C09 (propellers) on aircraft with jet engines.

 In the column “remark” those items should be marked where there is either a finding or a (cat G) remark.

Please find below detailed instructions for each information field to be completed by the inspector: No.: Report identification number generated by the centralised database, consisting of:  Identification of the NAA (8 digits maximum e.g. DGAC-F or CAA-UK);  Year (4 digits e.g. 2001);  Sequence number (4 digits maximum, starts at 1 every year).

Source: “RI” (the same report was used for the “standard report”).

Date: Date of the inspection (format: DD-MM-YYYY).

Place: Place of the inspection:  use the 4 digit coding from ICAO Doc. 7910 or/and the locations full name);  If the location does not have an ICAO indicator, use ZZZZ and specify in the “Additional information box” the location.

Local Time: Local time when the inspection started (format: 17:45).

Operator: Operators identification:  Use the 3 digit ICAO coding from ICAO Doc. 8585and/or the operator’s full name);  If the operator does not have an ICAO code yet, the Agency will allocate a temporary code;  The above identification procedure applies also for a private flight, unless the aircraft is not listed in the AOC of an actual operator and is actually used as a privately owned aircraft (not "an airline owned"): in such a case only, use ZZZ, indicate on the type of flight that it was a general aviation flight, ICAO Annex 6, Part II, and specify (if necessary) in the “Additional comment box” further details (e.g. the name of the operator/private pilot). The State of operator (registry) has to be selected manually.

AOC number: The number as shown on the AOC.

State: State of the Operator:  Use the 1 or 2 digit coding from the ICAO Doc. 7910 and/or the State’s full name).

SAFA Coordination Section Page 203 of 217 © European Aviation Safety Agency, July 2012 V 2.0

SAFA Ramp Inspection Procedures

Guidance material Type of operation: The type of operation (Part I, II, III as defined by ICAO Annex 6, or national operations).

Route from/ Route to: Airport of departure (for the inbound flight)/destination (for the outbound flight):  use the 4 digit coding from ICAO Doc. 7910 or/and the locations full name);  If the location does not have an ICAO indicator, use ZZZZ and specify in the “Additional information box” the location;  If the aerodrome code is not yet in the database, ask the agency to include the appropriate code.

Flight Number: Flight numbers assigned to the inbound/outbound flight.

Chartered by Operator: The identification of the operator who chartered this flight:  Use the same identification method as for the operator;  if not applicable, state NR (not relevant).

Aircraft Type Use the 3 or 4 digit coding from the ICAO Doc. 8643.

Registration marks The registration marks of the aircraft:  Pay attention to the correct position of the “dash” (-).

Aircraft configuration: Configuration of the aircraft (Pax, Freight or Combi).

Construction number: The construction number as shown on the official documents.

State of licensing: The State which issued the flight crew licences:  use the 1 or 2 digit coding from the ICAO Doc. 7910 and/or the State’s full name;  In case the State of Registry of the aircraft is different from the State of licensing, the “Additional comment box” should be used to record if a validation has been issued.

2nd State of licensing: In cases where the flight crew members are licensed by different States, the second State shall be recorded here:  In case of more than 2 States, use the “Additional comments box”.

Where during the SAFA Ramp Inspection some findings were established, specify: Code: Item code reference (e.g. B06 for Seat belts, C06 for wheel well) Std: Standard against which the observation was made (one digit):  I for ICAO standard,  N for national standard,  M for manufacturer’s standard,  O for others.

Ref The reference to the used standard (e.g.A6-I-4.3.1 for Annex 6 part 1 article 4.3.1, AMM 32-05-01 for the Aircraft maintenance manual chapter 32-05-01,CC29 for Chicago Convention, article 29) Cat Category of the remark:  1, 2 or 3 if it is a finding;  G if the remark only is a general remark, not a finding.

Finding Description of the finding:  If a PDF is used, the text cannot be amended in the database.

Further details can be entered in the “Detailed description” box; SAFA Coordination Section Page 204 of 217 © European Aviation Safety Agency, July 2012 V 2.0

SAFA Ramp Inspection Procedures

Guidance material  If the users do not use a PDF, the finding shall be described here. No further details are to be given in the “Detailed description box”;  If the users enter a cat G remark, no description shall be entered here. The remark needs to be described in the “Detailed description” box.

Detailed description Detailed description of the finding/remark:  If a PDF is used, further details can be entered here;  If the users do not use a PDF, no further details are to be given here;  If the users enters a cat G remark, the remark needs to be described here.

The class of actions taken: This block should indicate the actions required by/imposed by the inspector related to the findings of the Ramp inspection.

 Since the proof of inspection form shall be handed over to the pilot in command after each inspection, the class 1 action should always be marked.

Additional information: Free text box for any information additional to what has already been provided.

Inspector Name/number The names and/or numbers of the inspectors who performed the inspection.

SAFA Coordination Section Page 205 of 217 © European Aviation Safety Agency, July 2012 V 2.0 V 2.0 Page 206 of 217 Class 3 Corrective actions No No Yes Note: the specific actions consisting of operational restrictions, corrective actions before flight or at maintenance- base, grounding and/or entry permit repercussions have to be reported.

Class of actions

base Class 2

Appendix 3

Class of action matrix

Information to responsible NAA and Operator’s home No Yes Note: Written communication to the operator and to the NAA and copy to operator’s home base (findings of several inspections may be summarised in one communication) Yes Note: Written communication to the operator and to the NAA. In case of aircraft damage affecting airworthiness a direct communication with the responsible NAA should be established. The NAA in the State of registry decides about conditions regarding return to flight status. Confirmation afterwards with written communication to the NAA and copy to operator’s home base.

Captain (POI) Class 1 to Information Yes Yes Yes Minor Significant Major

SAFA Ramp Inspection Procedures Guidance material

INSPECTIONS Category 1 Category 2 Category 3

Category of findings

No findings means no cat. 1, 2, or 3 findings, but may include General Remarks.

ACTIONS TO BE TAKEN AFTER SAFA Coordination Section © European Aviation Safety Agency, July 2012 Note: In exceptional cases where multiple category 2 findings have been found and the accumulation of these findings or their interaction justifies a corrective action, the class of action may be increased to a class 3 action. 11

SAFA Ramp Inspection Procedures

Guidance material

Appendix 4

Information leaflet templates

SAFA Coordination Section Page 207 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspection Procedures

Guidance material Template 1 Leaflet for operators and their authorities

Safety Assessment of Foreign Aircraft

Information for aircraft operators and their competent authority Introduction In 1996 the European Civil Aviation Conference (ECAC) established a ramp inspection programme in order to assess the compliance of foreign aircraft with the applicable safety standards as set by the International Civil Aviation Organisation (ICAO). This voluntary programme has become mandatory for all Member States of the European Union as of April 2006. This leaflet is to explain the setup of the programme and the roles of the inspected operator and its competent authority.

Legal basis Directive 2004/36/CE of the European Parliament and of the Council on the safety of third-country aircraft using Community airports sets obligations for the Member States to inspect third country aircraft (aircraft not used or operated under the control of a competent authority of a Member State) which are suspected of non-compliance with international safety standards. In addition to this obligation, Member States may also inspect EU aircraft and may inspect aircraft according to a spot-check procedure without having any suspicion of non-compliance. The Annex to this directive has been amended by Commission Directive 2008/49/EC.

The obligations set out in the above-mentioned Directive pertain to the EU Member States only. However, the European Aviation Safety Agency has signed working arrangements with a number of non-EU States involving them in the SAFA programme. The EU Member States and the non-EU States are therefore called together the SAFA Participating States .

Which aircraft are checked?

The Participating States choose which aircraft to inspect. Besides the obligation that aircraft being suspected of non-compliance with the international safety standards shall be inspected, most participating States carry out random inspections.

What is checked?

A checklist of 54 inspection items is used during a SAFA Ramp Check. It is SAFA policy not to delay an aircraft except for safety reasons. Therefore, as the time between arrival and departure (the turn-around time) may not be sufficient to go through the full checklist, not all 54 items may be inspected. Checks may include:  licences of the pilots;  procedures and manuals that should be carried in the cockpit;  compliance with these procedures by flight and cabin crew;  safety equipment in cockpit and cabin;  cargo carried in the aircraft (including the transport of dangerous goods); and  the technical condition of the aircraft.

The inspections carried out by the Participating States follow a common procedure and are then reported by entering them into the centralised SAFA database of the European Aviation Safety Agency (EASA). It has to be stressed that SAFA inspections are limited to on-the-spot assessments, therefore do not substitute proper regulatory oversight; they cannot guarantee the airworthiness of a particular aircraft.

Proof of Inspection The Annex to Commission Directive 2008/49/EC obliges the Member States to give to the cockpit crew (or alternatively to other representatives of the operator) a so-called “proof of inspection” form when the inspection has been finalised; this form shows the contact details of the Participating State, the operational details of the flight, the checked inspection items and possible findings. The inspector will request the Pilot in Command to sign a copy of the proof of inspection. This signature is only to confirm that the form has been handed over to the crew; the Pilot in Command does not certify with his/her signature that he/she agrees with the findings. The information on the Proof of Inspection form may be subject to change when entered into the database as a result of quality checks on the findings, and may lead to an amendment, deletion or re-categorisation of findings.

The 44 States engaged in the EU SAFA Programme are: Albania, Armenia, Austria, Azerbaijan, Belgium, Bosnia and Herzegovina, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Moldova, Monaco, Montenegro, Morocco, the Netherlands, Norway, Poland, Portugal, the Republic of Georgia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, the former Yugoslav Republic of Macedonia, Turkey, Ukraine, and the United Kingdom.

SAFA Coordination Section Page 208 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspection Procedures

Guidance material Findings and follow-up actions Findings determined during an inspection are categorised according to the magnitude of the deviation of the requirements and to the influence on safety of the non-compliance. Minor deviations (category 1) are reported to the pilot in command. If an inspection identifies one or more significant deviations from the safety standards (category 2 findings), these will also be reported to the operator and its competent authority. Where non- compliances have a major impact on safety (category 3), the flight crew is in addition expected to correct such non-compliances before the aircraft departs. Relevant information not being a deficiency (e.g. no flashlights were on board, however the inspected flight was a daylight flight) may be reported as a category “G” (General) remark.

Follow-up process The Stakeholders involved in the SAFA process are the State of Inspection, the Operator, the State of Operator and the State of Registry (if different from the State of Operator). These organisations play a key role in the follow- up process after an inspection is conducted: 1. The SAFA inspector debriefs the Pilot in Command and hands over the Proof of Inspection.

2. The inspector requests the Pilot in Command to sign a copy of the Proof of Inspection form.

3. In case of category 2 and/or 3 findings, a written communication will be sent to the operator and to the competent authority overseeing the operator.

4. The operator is requested to reply to the written communication with an action plan which addresses the deficiencies.

5. The competent authority ensuring the oversight of the operator (and/or the airworthiness of the aircraft) may be asked to confirm their agreement on the corrective actions taken.

6. Findings are considered closed by the State of Inspection when the deficiencies have been satisfactorily addressed.

7. Subsequent inspections by any participating State may occur to verify rectification of the deficiencies.

Role of the operator When requested by the State of inspection, the operator has to provide information to the State of Inspection about the corrective actions taken on the deficiencies. These actions should include a root cause analysis and may consist of any actions taken and/or planned to correct the deficiencies, and any actions to prevent/limit re- occurrence in the future. Failure to send the appropriate information in a timely manner might be considered an indication of the lack of ability and/or willingness to address safety deficiencies (as referred to in the Annex of Regulation (EC) No 2111/2005).

Role of the competent authority The competent authority is responsible for the oversight of the operator, the aircraft and/or the personnel licensing of the flight crew. The States of Inspection are not taking over this responsibility by performing SAFA inspections.

However, the competent authority may use the SAFA inspection results as additional information during their oversight activities. For that reason, any inspections raising category 2 (significant) and/or category 3 (major) findings are forwarded to the competent authority. In certain cases, e.g. following numerous, repetitive or serious findings, the inspecting State may request the competent authority to confirm that they are satisfied by the corrective actions taken and/or planned by the operator. Failure to send the appropriate information in a timely manner might be considered an indication for the lack of ability and/or willingness to address safety deficiencies (as referred to in the Annex of Regulation (EC) No 2111/2005).

Database analysis All reported data is stored centrally in a computerised database set up and managed by EASA. The database also holds supplementary information, such as lists of actions carried out after an inspection which revealed non- compliances. The information held within this database is reviewed and analysed by EASA on a regular basis. The European Commission and Participating States are informed about the results of the analysis and are advised on any potentially safety hazards identified.

Whom to contact for questions?

The participating States are responsible for the performance of the inspections. In case of any questions resulting from an inspection, the operator should contact the participating State directly. The contact details of the participating State are on the Proof of Inspection form handed over to the crew. General information on the SAFA programme can be found on the website of the European Aviation Safety Agency (http://www.easa.europa.eu/ws_prod/s/s_safa.php).

SAFA Coordination Section Page 209 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspection Procedures

Guidance material Template 2 Leaflet for the general public

Safety Assessment of Foreign Aircraft

Information for the general public Introduction The European Civil Aviation Authorities perform since 1996 ramp inspections on aircraft visiting their countries. During such an inspection, the compliance with the applicable International safety standards (issued by the International Civil Aviation Organisation [ICAO]) is checked. These inspections became mandatory for all Member States of the European Union as of April 2006. This leaflet is to explain the setup of the program.

Legal basis Directive 2004/36/CE of the European Parliament and of the Council on the safety of third-country aircraft using Community airports sets obligations for the Member States to inspect third country aircraft (aircraft not used or operated under the control of a competent authority of a Member State) which are suspected of non- compliance with international safety standards. In addition to this obligation, Member States may also inspect EU aircraft and may inspect aircraft according to a spot-check procedure without having any suspicion of non-compliance. The Annex to this directive has been amended by Commission Directive 2008/49/EC.

The obligations set out in the above-mentioned Directive are for the EU Member States only. However, the European Aviation Safety Agency has signed working arrangements with a number of non-EU States involving them in the SAFA programme. The EU Member States and the non-EU States are therefore called together the SAFA Participating States .

Which aircraft are checked?

The Participating States choose which aircraft to inspect. Besides the obligation that aircraft being suspected of non-compliance with the international safety standards shall be inspected, most Participating States carry out random inspections. Both aircraft used by EU operators and non-EU operators may be inspected.

What is checked?

A checklist of 54 inspection items is used during a SAFA Ramp Check. It is SAFA policy not to delay an aircraft except for safety reasons. As the time between arrival and departure (the turn-around time) may not be sufficient to go through the full checklist, not all 54 items might be inspected. Checks may include:  licences of the pilots;  procedures and manuals that should be carried in the cockpit; compliance with these procedures by flight and cabin crew;  safety equipment in cockpit and cabin;  cargo carried in the aircraft; and  the technical condition of the aircraft.

The inspections carried out by the Participating States follow a common procedure and are then reported by entering them into the centralised SAFA database of the European Aviation Safety Agency (EASA). It has to be stressed that SAFA inspections are limited to on-the-spot assessments and cannot substitute for proper regulatory oversight, therefore they cannot guarantee the airworthiness of a particular aircraft.

The 44 States engaged in the EU SAFA Programme are: Albania, Armenia, Austria, Azerbaijan, Belgium, Bosnia and Herzegovina, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Moldova, Monaco, Montenegro, Morocco, the Netherlands, Norway, Poland, Portugal, the Republic of Georgia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, the former Yugoslav Republic of Macedonia, Turkey, Ukraine, and the United Kingdom.

SAFA Coordination Section Page 210 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspection Procedures

Guidance material Findings and follow-up actions A non-compliance found during an inspection is called a finding. Such findings are categorised according to the magnitude of the deviation of the requirements and to the influence on safety of the non-compliance.

Minor deviations (category 1) are reported to the Pilot in Command. If an inspection identifies one or more significant deviations from the safety standards (category 2 findings), these will also be reported to the operator and its competent authority. Where non-compliances have a major impact on safety (category 3), the flight crew is in addition expected to correct such non-compliances before the aircraft departs by either correcting the deficiency or by imposing restrictions on the aircraft operations (by e.g. blocking a defective seat for its use by passengers).

Follow-up process The Stakeholders involved in the SAFA process are the State of Inspection, the Operator, the State of Operator and the State of Registry (if different from the State of Operator). These organisations play a key role in the follow-up process after an inspection is conducted: 1. The SAFA inspector debriefs the Pilot in command and hands over the Proof of Inspection.

2. The inspector requests the pilot in command to sign a copy of the Proof of Inspection form.

3. In case of category 2 and/or 3 findings, a written communication will be send to the operator and to the competent authority overseeing the operator.

4. The operator is requested to reply to the written communication with an action plan that addresses the deficiencies.

5. The competent authority ensuring the oversight of the operator (and/or the airworthiness of the aircraft) may be asked to confirm their agreement on the corrective actions taken.

6. Findings are considered closed when the deficiencies have been satisfactorily addressed.

7. Subsequent inspections by any Participating State may occur to verify rectification of the deficiencies.

Database analysis All reported data is stored centrally in a computerised database set up and managed by EASA. The database also holds supplementary information, such as lists of actions carried out following inspections which revealed non-compliances. The information held within this database is reviewed and analysed by EASA on a regular basis. The European Commission and Member States are informed about the results of the analysis and are advised on any identified potentially safety hazards.

Whom to contact for questions?

The Participating States are responsible for the performance of the inspections. In case of any questions resulting from an inspection, one should contact the Participating State directly. General information on the SAFA programme may be found on the website of the European Aviation Safety Agency (http://www.easa.europa.eu/ws_prod/s/s_safa.php).

SAFA Coordination Section Page 211 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspection Procedures

Guidance material

Appendix 5

Written communication templates

Template 1 Written communication to aircraft operators The written communication to the operator to report category 2 and 3 findings should contain the following information:  a short reference to the SAFA programme,  why this written communication has been sent (class 2 action),  reference to the ramp inspection report,  request for evidence for corrective actions of the deficiencies,  request the operator to include, as a copy, its competent State of Oversight in the exchange of the corrective actions requested.

Note: The template contains the required information mentioned above. Although the use of this template is encouraged in order to standardise the written communication, elements of this template may be amended where necessary to match the individual cases.

Dear Sir, I kindly ask your attention for the following: Your aircraft has been inspected in the scope of the European SAFA programme (Safety Assessment of Foreign Aircraft). As described by the SAFA programme procedures, the ramp inspection reports are, in the case of significant and/or major findings, sent to both the concerned operator and the authorities responsible for the oversight of that operator. A copy of the ramp inspection report, as it has been entered into the centralised European database, is attached.

Concerning the findings categorised as category 2 or 3, the SAFA procedures require me to request evidence of corrective action(s) that have been or will be undertaken to correct these findings and to prevent re-occurrence in the future. You may inform me (in writing) either directly or through your authority. As your authority is the entity responsible for the safety oversight of your operations, they might be asked to confirm that they are satisfied with corrective actions. In this frame, I would kindly invite you to also transmit to their services a copy of the elements requested aforementioned.

I thank you for your cooperation in the field of air transportation safety, and inform you that additional ramp inspections may occur when aircraft of your airline lands on the territory of one of the States participating in the SAFA programme.

Should you require any additional information on this matter, do not hesitate to contact our services.

Yours faithfully, SAFA Coordination Section Page 212 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspection Procedures

Guidance material Template 2 Written communication to National Aviation Authorities The written communication to the NAA to report category 2 and 3 findings should contain the following information:  a short reference to the SAFA programme,  why this written communication has been sent (class 2 action),  reference to the ramp inspection report,  optional: request for confirmation that the NAA is satisfied with the corrective actions.

Note: The template contains the required information mentioned above. Although the use of this template is encouraged in order to standardise the written communication, elements of this template may be amended where necessary to match the individual cases.

Dear Sir, I kindly ask your attention for the following: Aircraft from one or more operators for which you ensure the oversight, have been inspected in the scope of the European SAFA programme (Safety Assessment of Foreign Aircraft). As described by the SAFA programme procedures, the ramp inspection reports are, in the case of significant and/or major findings, sent to both the concerned operator and the authorities responsible for the oversight of that operator. A copy of the ramp inspection report, as it has been entered into the centralised European database, is attached.

The operator has been requested to provide evidence of any corrective actions taken. [ This sentence is optional: Because of the nature, the number and/or the re-occurrence pattern of the findings, I would like to receive your confirmation that you are satisfied with these corrective actions]. The information contained in the ramp inspection report as well as the corrective actions taken by the operator might be useful for your oversights activities.

I thank you for your cooperation in the field of air transportation safety, and inform you that additional ramp inspections on the operator(s) may occur when their aircraft land on the territory of one of the States participating in the SAFA programme.

Should you require any additional information on this matter, do not hesitate to contact our services.

Yours faithfully, SAFA Coordination Section Page 213 of 217 © European Aviation Safety Agency, 2012 V 2.0

SAFA Ramp Inspection Procedures

Guidance material

Appendix 6

Monthly report template

Template Monthly report on SAFA follow-up actions SAFA Coordination Section Page 214 of 217 © European Aviation Safety Agency, 2012 V 2.0 dditional A Information Findings closed/ Supplemental Communication (C/S)

(month/year)

Answer Satisfactory (Y/N/P) State of Oversight Reply Received on (date) Month: Reply Requested (Y/N) STATE OF OVERSIGHT SECTION Receipt Confirmed (Y/N) Written to NAA (date) communication

(name)

State of Oversight

(name)

State: Findings closed/ Supplemental communication (C/S) NAA: Operator Reply 8 Answer Satisfactory (Y/N/P) Received on (date) Receipt confirmed (Y/N) OPERATOR SECTION

Monthly report on SAFA follow-up actions

Written communication to operator (date) Findings (1-2-3) (optional) Operator Name

Page 1 of 1

Code (optional)

RI# Operator For guidance on how to fill-in this report please refer to Chapter 6.3

SAFA Ramp Inspection Procedures

Guidance material

Appendix 7

National Coordinator Tasks

1. GENERAL TASKS To control and manage the SAFA programme within the Member State the national coordinator could be allocated the following tasks:  to ensure that the ramp inspection reports referred to in Article 3.1 of the Commission Regulation (EC) No 768/2006 shall be entered without delay into the centralised database (within 15 working days according to paragraph 4.4 of the Annex to the Commission Directive 2008/49/EC).

 to ensure that the ramp inspections shall be prioritised in accordance with Article 2 of the Commission Regulation (EC) No 351/2008.

 to nominate national representatives for the SAFA working groups (on procedures, in depth analysis, ad-hoc);  being the responsible focal point for the training schedules (initial & recurrent) for all involved national SAFA staff, e.g. inspectors, senior inspectors, data base users, moderators, etc.;  to represent the Member State at the “European SAFA Steering Expert Group” (ESSG) meetings and, when and where applicable, at other SAFA related meetings;  to promote and implement the SAFA inspector exchange programme;  to promote the SAFA programme within the Member State by means of annual reports or other publications;  to support legal advisors dealing with request for disclosure of SAFA related data.

According to Article 6.1 of Directive 2004/36/CE any information received from the other Member States shall be treated as confidential. This means that, whilst national reports might be disclosed depending on national freedom of information act, confidentiality must be ensured for ramp inspection information received from the other States (e.g. accessible by means of the SAFA database;  to ensure that distribution and adoption of new legislation, latest versions of SAFA procedures are controlled and distributed to all involved SAFA staff;  to ensure that all SAFA staff involved in ramp inspections are properly trained and scheduled for recurrent training;  to organise regular meetings with all SAFA staff to maintain a high standard of quality relating to:  any changes/updates to the SAFA procedures,  feedback on quality issues with regard to SAFA reports e.g. incorrect entry’s, mistakes, omissions, etc.,  staff issues, e.g. new staff, mentorship, etc. .

 to implement a national SAFA quality control system, for instance consisting of the feature built into the centralised SAFA database (moderator function/workflow function);  to establish and maintain a system that regulates the access of national operators and NAA staff to the centralised SAFA database;  to assist the Agency at all stages of the SAFA standardisation audit process and to accompany the inspection team throughout the audit;  to propose team members for SAFA standardisation visits. Proposed team member(s) shall meet the criteria of article 6.2 of Commission Regulation (EC) No 736/2006.

SAFA Coordination Section Page 216 of 217 © European Aviation Safety Agency, 2012

SAFA Ramp Inspection Procedures

Guidance material 2. REPORTING TO EASA, THE COMMISSION AND THE MEMBER STATES The SAFA national coordinator:  maintains good communication with EASA SAFA Programme Coordination for all SAFA related activities;  timely informs EASA when there are changes to key staff contacts, e.g. national SAFA coordinator, coordinator national operators, database users etc.;  shall make available, in accordance with article 6.4 of the Annex II to Commission Directive 2008/49/EC, a monthly report with the status of the follow-up actions taken pursuant to ramp inspections (or make use of the associated functionality in the SAFA database);  according to article 5 of Directive 2004/36/CE: o Art. 5.1; Participate in the mutual exchange of information; o Art. 5.2; Submit to the Commission and the Member States safety information as collected in standard reports; o Art. 5.3; Inform to the Commission and the Member States, without delay, of any potential safety threat.

3. CONTACTS WITH OPERATORS The national coordinator should ensure that, in accordance with article 6.4(1) of the Annex II to the Commission Directive 2008/49/EC, for all category 2 and 3 finding(s) a written communication will be sent to the operator to request evidence of corrective actions taken.

Furthermore he should act as the focal point for any questions regarding performed ramp inspections raised by the inspected operator.

4. CONTACTS WITH AUTHORITIES The national coordinator should ensure that, in accordance with article 6.4(2) of the Annex II to Commission Directive 2008/49/EC, a written communication will be sent to the responsible State of oversight, addressing the results of the inspections and, were appropriate, request for a confirmation that they are satisfied with the corrective actions performed by the operators under their supervision. Furthermore, he/she should act as the focal point for any questions raised by NAAs regarding performed ramp inspections, or when he/she receives the previously mentioned request for confirmation from other NAAs.

If it concerns an inspection of an Operator licensed in the EU or in another SAFA participating State, the communication should be sent via the relevant SAFA national coordinator. In case there is a dedicated coordinator for national operator(s), information concerning SAFA inspections should also be sent to this coordinator.

If it concerns an inspection on a non-EU or SAFA participating State, the Flight Operations department of the non-Member State may be the most suitable point of contact. Other sources for finding contact details could be the ICAO or NAA Authority website, also on SINAPSE there is (uncontrolled) information on contact details provided.

5. INSPECTION REPORTS ON NATIONAL OPERATORS The SAFA National Coordinator is requested to ensure proper distribution of SAFA Inspection Reports on Operators, which are under the supervision of his National Authority. This particularly applies where the participating state has not nominated a Coordinator National Operators and therefore this task part of the task of the SAFA National Coordinator.

SAFA Coordination Section Page 217 of 217 © European Aviation Safety Agency, 2012