What is the maximum gross lift of the K-type airships?

The maximum gross lift for K-type airships is approximately 26,970 lbs.

What engines are used in the K-type airships?

The K-3 to K-8 models use Wright R-975-28 engines, while the K-9 and future models use Pratt & Whitney R-1340-AN2 engines.

How is static lift defined in the context of airships?

Static lift is the component of lift due to buoyancy, independent of the airship's motion, calculated as the difference between the weight of the air displaced and the weight of the lifting gas.

What are the overall dimensions of the K-type airships?

The K-type airships have a height of 79.00 feet and a length ranging from 248.50 to 251.70 feet.

What is the useful lift ratio for K-type airships?

The useful lift ratio for K-type airships is approximately 0.310.

Airship Pilot Manual —

LexTest_2014_08_18_07_23_14_714

UNITED STATES NAVY

· K-TYPE AIRSHIPS

PILOT'S MANUAL

RESTRICTED CONTRACTS NOs-78121 and NOa(s)-257

GOODYEAR AIRCRAFT CORPORATION

AKRON, OHIO ., .

First Issue: Sept ., 1942 Revised Issue: Sept. , 19 43 iii iv v THE CONTENTS OF THIS MANUAL ARE

RESTRICTED

EXTRACT FR0M ESPIONAGE ACT "Section ' 31. Unlawfully obtaining or permi ttlng to b~ obtai'Hed information effect- ing National Defense.***; or (d) whoever,law- fully or unlawfu+ly having possess : ion of, : access to, contr .Ql over, or being intrusted . with any document, -writing, code book, : signal book, sketch, photograph, photographic nega- tive, plan, blueprint, map, model, ins~rumen~ a~pliance, or note relating to the National Defense, willfully communicates or transmits or attempts to communicate or transmit the same to any person not entitled to receive it, or willfully re~ains r the same · and f~ils to deliver it . on demand to the officer or employee of the United States entitled to re- ceive it, or (e) whoever, being intrusted with or having lawful possession or control of any document, writing, code book, signal book, sketch, photograph,_ photographic nega- tive, blueprint, plan, _map, model, note, or information relating to the National Defense, through gross negligence permits the same to be removed from its proper place of custody or delivered to anyone in violation of his trust, or to be lost, stolen, abstracted or destroyed, shall be punished by a fine of not more than . $10,000 or by imprisonment for not more than two years or both."

P/2£FAf!E

The information herein is designed to embody only such material as may be of value to the pilot and the crew of the K-airship during flight operations. Further descriptive matter vital to the ship and its care is set forth in the Specification and Maintenance Manuals.

While this manual is not intended to serve as an infallible gtiide for all flight operations, some of the more advanced points of aerostatics are included for ready reference.

Amendments will be made when significant changes in future airships occur.

The Goodyear Aircraft Corporation welcomes sug- gestions for the improvement of the airship and its equip- ment, and invites constructive criticism of this manual.

Such suggestions will be cordially entertained and accorded the most careful consideration.

vii

7A8l£ OF &ONTENTS

PART I. GENERAL DESCRIPTION A. DIMENSIONS AND CHARACTERISTICS 1 • • • • • • • • • • • • • • • • • • ....... . ............. . ......

1. Overall Dimensions 1 2. Envelope 1 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Ballonets . ... ... . . .. . .......... . . . . .. . . . ....

3. 1

.. . . .... . . . . . . . . . .. .. ~ . . . . . . ... Tail Surfaces

4·

5. We:ights and Lift . .. . . .. ... .. . . . . . .... . . . .. . . 2

B. AVERAGE PERFORMANCE . .... . .. .. .... . . ..... . .. . ... ..

PART II. FLIGHT AND FLIGHT CONTROL A. FLIGHT CHARACTERISTICS • • • • • • • • • • • • • • • • • • • • • • • • • 4

1. .... .. . .. . . . . . .... . . ... . ... . ..... Static Lift

Dynamic Lift .......•....•.......•.• ·- · ...... . 12

Factors of Safety 12 • • • • • • • • • • • • • • • • • • • • • • • • • • • 4· Weight Empty ...... ........ . . . . . . . . . ... . .

5. 15 6. . . . . . . ......... ...... .. .. .. ... ...

Useful Load 18 . . . . .. .. . ... . ..

B. ENVELOPE PRESSURE CONTROL SYSTEM 22 . .. . . . .. . .. .. . ... .. . . . .. .

1. General Description 22 2. Air System . .... ...... . . . .. . ... . .. .. .. . .. . . . .

a. Scoops ... . . . ..... . ...... . . . . ..... . . . . . .. . 23

b. .. . . . . . .. . ... . .. . . .. . . . . . . . Valve Settings

c. Pressure Regulation .. . .. . ... . . ... ...... ..

Air Valve Adjustment . ... ... . . . . .. ... . ... .

d. 29 .. . .. ...... . .. . .... . ......... . . . .

e. Take-Off ...... . . . . . ... .. . . . . ..... . . ...... . ..

f. Climb .. . . . . . . . .. . . . . .. .. . . .. . . . . ..

g. Level Flight 36

h. . . . .... . ... . . .. . . . ... .. .... .... Descending 37

i. Landing .... . . . . . ... . .. . .... . . . . . . . . .. .. ..

Shifting Air . . . . .. . . . . .. .. ... .. . ... .. . . . . 38

j ..

!C. Blowing Air into the Gas .. . .. . ...... . .

viii 3. Gas Release System .. . .... . . .. . ... . .. . . . . . . .. . .

a. Gas Valves .. . . . ....

b. Rip Panels ... . . . . . . . . .. . . . .

4· Controls and Auxiliaries .. . . . .... .. . .. . . . . . ... .

a. Valve Controls . . . . . . . .. . . . . . . . ..

b. Damper Control . . .. . . . ..... ... .. . . . .

c. Manometers .... . ... . .. . ... . .

d. Starting Auxiliary Blower .....

e-.

Stopping Blower . . .. .. . . .....

f. La Del Electric Blower .. . . ....

5. Summary: Pressure Control System .. . ... . ...... .

a. Settings . . . ... . .. .. . .... ... . . . . . . .... . . . .

b. Controls, Instruments & Auxiliaries Chart ...

c. Operation Chart . .......•..... . ..•...........

C. MAJOR CONTROLS . .. ....•............•..•...•.........

D. RETRACTABLE LANDING GEAR . ... .. . . . .. . . . . .. . . . . .. . .

E. HANDLING LINES .....••..•••...•.. . .••.........••.••

PART III. POWER PLANT A. ENGINES .................................. ·- ....... .

General Characteristics .. . ..

2. Starting .. . . .

3. Warming Up . . . .. . . .

Ground Test . . .. . ..

4· •• . . .. . . . ....

5. Take-Off 6. Cruising . . . . . .. ..

7. Single . .. .

Engine Operation 8. Stopping .....

. .. . . . . . . . .. . .

9. Operating Limits and Charts ...... . ....

ix B.

FUEL SYSTEM .. .. .... . . .... . . .. . ... . .. .. . . . . . .

c. RECOMMENDED CARBURETOR ADJUSTMENT

•·• ........ . 70

D. OIL SYSTEM PART IV. ELECTRICAL SYSTEM GENERAL DESCRIPTION ., ........ . . . . . . . . .. . .. .. .

B. DISTRIBUTION • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • c. CONTROL BOXES AND CUT-OUTS ............. .. ......

1 •. Carbon Pile Regulator • • • • • • • • • • • • • • • • • • • • 2. Service Troubles .... ~ . . ............. . ....

D. LOCATION OF COMPONENT PARTS . . . .. . .. . ....... .

1. Switches ••..•.••.. . ......•.....•...•..•.. -

Automatic Controls ... . .... . . . ..... . . . . . ..

3. . . . . . . .. ... .... . . . . . . ... . . .. . . Instruments

Cooking . . . . . .. . . .. . . . . . . . . . . . . . . . .. . .. . . .

4· 94 5. Lamps ... . ..... . . ....... . ... . ..... . .. . ....

6. Fuses .. . ....... ·• . ... ............. . . ..... .

E. LAWRANCE AUXILIARY GASOLINE POWERED ELECTRIC

GENERATOR . . . . . . .. .. .. . .... . ... ... ...... . .. . . 102

1. Specifications ••••••••••••••••••••••••••• . ......... . . . ...

2. Preparations for starting 102

3. Starting . . ........ . . . .... . . . . . ..... .. . .. . 105

Manual Star . ting ........... ... .............. .

4·

Warm Up . . . ..... . .. . . . .... . .... . .. . ..... . . . 106

6. Loading ... . . . . . . ... . .. . . .. .... ..... . . . . . . 106

7. ...... . . . . . . .. . . . . .. . . .. . Overload · Caution 106

.................... . ....

8. Overspeed C~t-Out 107 9. Stopping the Engine . . .. . ...... .. .. . . . . . . .

PART V. MISCELLANEOUS

A. HEATING SYSTEM ... . . . . . .. .... . ....... . ... . . . . 108

B. FIRE EXTINGUISHING SYSTE1! .. .. . .. . .... .. . .. . . 110

c. BOMB HATCH . . .. . . . . . .. . . . . .. . ..... . . .... . . . . .

D. SERVICE ENGINEERING .. .. .... . .... . . . . . . . . . . . . 111

E. NOTES . . . . . . .. . .... .. . . . .. . .. . . . .. . . .. ... . .. . 112

X Fig. I Superheat Chart .....................

Fig. XX Helium Purity ... .. ..... . ..... ... . ...

Fig. III Dynamic Lift Chart .. . .. . .. . . . . . . .. ..

Fig. IV Take-Off Chart .... . ... . .. . . . . . . . .. ..

Fig. V Air Pressure System Fig. VI Air Scoops . .. . ......... . ..... . .. . . ..

Fig. VII Air Pressure in Excess of Gas Pressure

- VS - % Fullness of Ballonets at Zero

Pitch Angle at Standard Unit Lift Conditions ···············~·········· Fig. VIII 36" Air Valve, K-3 thru K-53, Excl. of K-49 ........•.......•..............• Fig. IX 36" Air Valve, K-49, K-54 & Future ••• Fig. X Helium Inflation Sleeve ....... . .....

F:i,g. XI Flight & Instrument Panel ...... . ....

Fig. XII Starting Auxiliary Blower .. . . .. ... ..

Fig. XIII Controls, Instruments & Auxiliaries Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Fig. XIV Operation Chart - Pressure Control Sys tern • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 4 7 Fig. XV Major Controls •••••.••••.•••.••.•••. 48 Fig. :xvi Top of Landing Gear Strut . . . .... . . ..

Fig. XVII Landing Gear Shaft . .. . ... .. ....... ..

xi Fig. XIX Horse Power VS. Manifold Pressure 61 (Sea Level Performance) ••••••••.•••••• Fig. XX Horse Power VS. Manifold Pressure Fig. XXI Power Curves for Pratt & Whitney Engine Model H.P.. -1340-AN-2 (At Sea Level) •••••••.•••••.•••••••••• Fig. XXII Power Curves for Pratt & ~~itney Engine Model HR - 1340-~~-2 (At 1500 Ft. Altitude) ................. .

Fig. XXIII Fuel Consumption & R.P.M. - VS.

Air Speed (K-3 thru K-8) ....•..•...•.

Fig. XXIV Fuel Consumption & R.P.M. - VS.

Air Speed (K-57 & Future) ••••••••••••• Fig. "XXV Economical Air Speeds Fig. XXVI Mechanic's Check · Chart . . . . . . .. . . .. . . ..

Fig. XXVII Fuel System .•••••••••••••••••••••••••• 71 Fig. XXVIII Fuel System, Schematic Diagrams (K- 3 thru K-10) ••••••••••••••••••••.•• 72 - 76 Fig. XXIX Fuel System, Schematic Diagrams (K-11 and Future) ••••••••••••••••••••• 77 - 81 Fig. X"XX Oil System, K-3 thru K-74 .. . . . . . ... . ..

Fig. XXXI Oil System, K-75 and Future ...........

Fig. XXXII Electrical Load Analysis . .. ... . . .. .. ..

Fig. X"XXIII Auxiliary Panel . .. . . .. . ... . . .. . . . . . . . .

Fig. XXXIV Generator Control Box and Battery Ins tall a tion . . . . . . . . . . . . . . . . . . . . . . . . . . 91 xii

Fig. XXXV Spare Lamp Data Chart .. . .. .... ... .. .. . . - 98

Fig. XXXVI Electric Fuse Data Chart - 101 Fig.

XXXVII Auxiliary Generator and Blower . . . . .. . . 104

Fig .. XXXVIII Heating System ... . .... ........... ... . . 109

xiii

PART I

(/Eh'l:R.Al 1J£SfJRIPTIOA'

- -- , 71" " :.,.

_,r;_~::~~~-~ - :_ ",,, ... :;~; ~~~!

:-:::. .

========!. GENERAL DESCRIPTION A. DIMENSIONS AND CHARACTERISTICS K-3 K-14 1. Overall Dimensions - Feet to K-13 & Future Height .. . . ... ... . ... . . . . . .. . .. ... . . .

79.00 79.00 Width 62.50 62.50 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Length . . . . . . . ... . .. ... ... ... ..... . . . 248.50 251.70

2. Envelope Theoretical: 416,000 ' 425,000 VolllDle, 0u.Ft. •••••••••••••••••••• Surface Area, Sq. Yds ••••••••••••••• 3,900 3,965 Length, Ft. . ....•...•. . .............• 246.00 249-20 Diameter, Ft. . .•• . .......•••.....••.

57.85 57.85 Fineness or Slenderness Ratio ••••••• 4-31 4-~5 ·Maximum Section from Bow, Ft. • •••••• 98.40 98.40 Center of Buoyancy, Ft. • ••••••••••• 112.40 113.95 Demonstrated Volume (with . stretch) Cu. Ft. . ..•................•....• 424,600 435,000 3. Ballonets K-7 K-14 K-3 to K-13 & Future to K-6 Volume - CU.Ft.: 53,000 58,950 55,700 Forward •••••••••••••••••• Aft •••••••••••••..••••••• 58,400 58.400 61,600 Total 114,100 111,400 120,550 •••••••••••••••••••• Per Cent Envelope Volume 26.8 27.7% 27.5 Surface Area- Sq. Yds.: Forv1ard •••••••••••••••••• Aft ...................... . 562 562

~

Total 1106 1087 1106 ••••• • ••••••••••••••• j -1- ; 4· Tail Surfaces - Sq. Ft.

All Ships Fins: Horizontal (2) •••••••••••••••• 732 Top (1) •••••••••••••••••••••• Bottom (1) ••••••••••••••••••• Total ••••••••••••••••••••••••• Rudders: Top (1 ·) .••......•..•.....•.•• . 130 Bottom (1) ••••••••••••••••••• ...2.2. * Total •••••••••••••••••••••••••

Elevators (2) . . . .. ... ... . . . .... . . . 260

GRAND TOTAL - Tail Surfaces .. 1807

Weight and Lift - Lbs.

K...;l4 K-3 K-9 to K-8 to K-1.3 &: Future Gross Lift (Based on 62 lbs.

per 1000 Cu.Ft.with stretch) 26,325 26,325 26,970 Approximate Total Weight, 17,600 Empty 18,350 18,430 • • • • • • • • • • • • • • • • • • • • Approximate Useful Lift 8,725 7,975 8,540 •• Ratio Useful Lift to Gross .•......••.•. ......•..

Lift .331 .303 .310 6. Power Plants K-3 to K-8: Engines (2) Wright, Model R-975-28, Direct Drive-Horsepower, each 420 H.P. at 2200 RPM Propellers (2) - Three Blades - 9•on Diameter.

K-9 &: Future:Engines (2) Pratt &: Whitney Wasp, Model R-1340 -AN2, Geared 3:2 Horsepower, each - 425 H.P. at 1775 RPM Propellers (2) - Three Blades - 12'0" Diameter Propeller Pitch: Diameter Pitch Setting at 42" Station 12'6" 12'0" 11'6" *Inboard aft corner cut to prevent puncturing the envelope during heavy landings.

-2-

B • . AVERAGE PERFORMANCE *

) K-3 thru K-8 K-9 thru K-13 K-14 &: Future Speed Knots •••••••••••• 50.0 62.5 67 . • 5 67.5 40 50 50 40 50

.. . . .... . .... ... 1780 2200 1120 ],.050 1290

R.P.M. 1450 1340 1775 1740 I Fuel Consumption \.oJ I Lbs./Hour ••••••••••••• 102 120 160** 520 98 160** 375 165** 400 Endurance, Hourf> Based on 6000 Lbs.Fuel 50 37.5 11.5 5200 Lbs.Fuel 53.2 32.5 14

- - -

"

II 5650 Lbs.Fuel 14.1

- - - - - 55.0 34.2

-

"

Range, Nautical Miles ••. 2000 1875 690 2130 1625 2200 1710 950 * See Pages 65, 66 and 67 for more complete performance data.

**Based on lean carburetor setting.

RECO MM ENDED TOP SPEED - 67.5 KNOTS PER HOUR.

filtJHT AN!JliJtJHT CfJJYTROL

s··;: ,;;~~ .

. · . ..• . :_ ~ .. : ~)~

- =======II. FLIGHT& . FLIGHT CONTROL======== A. FLIGHT CHARACTERISTICS The lift of an airship is made up of two components -- the static lift and the dynamic lift. These two components have different physical origins and require separate treat- ment.

(1) Static Lift The static lift is that component of lift which is due to buoyancy and which iS independent of any motion of the ship with respect to the air.

The gross static lift of an airship is the difference between the weight of the air displaced and the weight of the lifting gas.

The net lift is the difference between the gross lift and the gross weight of the ship.

The ship is said to be "light" when the gross lift ex- ceeds the gross weight. The ship is said to be "heavyn when the gross weight exceeds the gross lift.

In calculating the gross lift of an airship both the gas volume and the lift coefficient of the helium, or lift per 1000 cubic feet, must be knovm.

The lift coefficient c.an be computed, as indicated be- low, when various conditions of the atmosphere and of the helium are known.

The gas volume, however, can be determined accurately only when the ship is fully inflated. Calculations of gross lift are largely limi t · ed, therefore to full inflation.

-4- Ordinarily an airship takes off less than fully in- flated and the lift condition is determined by a wei g h-off rather than by calculation. After take-off, the pilot is interested in keeping track of the variations in gross and n~t lift as affected by the burning of fuel or dropping of ballast on the one hand, and by the variations in atmos- pheric conditions on the other. The changes of lift can be followed by means of simple rules of thumb discussed later on.

(a) Calculating Full Inflation Lift References: (1) War Department Technical Manual TM-135 (2) Goodyear Aircraft Report on 100% Weigh Off of K-4 Airship, Oct.l5, 1941, Revised Nov. 6, 1943.

The lift coefficient, or lift per 1000 cubic feet can be computed from the following formula: 1325 - 16.7 Ra Ea 185 - 21.5 Rg Eg (1)

L = CP

Ta Tg Where: L =Lift Coefficient in lbs. per 1000 Cu.Ft.

c

= Gas Purity, % p = Atmospheric Pressure, in. of HG.

Ta = Absolute Air Temperature, oF.= Plus

459.8 Air Temp.

-

oF.= Tg Absolute Gas Temperature, 459.8 Plus Gas Temp ..

-

Ra Relative Humidity of Air, - % - Rg Relative Humidity of Gas, - % Ea Vapor Pressure at Temperature, Ta

=

- Vapor Eg Pressure at Temperature, Tg -5- C.-F.

-- -

=

- :::::: -

=

= -

::::::

=

= -

=

- ::::::::: 1-- ~ - r-

=

1--

=

::::::::: ~

=

5 =

=

r- f-

=

- ;:::::

=

= - 5 ,..__

=

1-- EFFECT °F. SUPERHEAT EFFECT °C. SUPERHEAT

=

f- ON LIFT ON LIFT

=

lO -

=

-

=

oF.

:::::::::

-

LBS.

°C. LBS.

-

= - -

1500 30 15 ' 00 ..,__ FARENHEIT f-- CENTIGRADE SCALE 1-- 1000 20 1-- 1000 1-- ~ 1-- 5

-

0 0 For K-Airship Fig. I Superhea.t Chart -6- If the effect of humidity is neglected, the formula oecomes: CP 1325 - 185 (2)

L =

Ta Tg If Tg = Ta and there is no superheat, then: CP (3)

L = 1140

Ta Formula (3) may be accurate enough for rough computa- tions. But even when more accurate results . are desired, it may be found convenient to use this formula and to apply quick corrections for humidity and superheat according to the following rules: l. of positive superheat, For each 5° increase lift by 1%.

negative 2. For each 5° of superheat, reduce lift by 1%.

3. Correct for humidity in accor d ance with the following table: LOSS IN LIFT CAUSED BY HUMIDITY Air Temperature Loss in Lift at Saturation 0°F l/20 of 1% 20oF l/10 of 1% 32°F l/5 o"f 1% l/2 of 1% 50°F 70°F 1% less than dry air 1.8% less than dry air 90°F l00°F 2.5% less than dry air For less than 100% humidity, multiply loss in lift at satu:ration by %humidity.

-7- FIG. 21 ~--·-·--- -- ' _, I • ~ + I I - l - --- - l- 1 r] -.30:-2 ~ t • ·r f ' !

-8- Fig. II - Helium Purity The curves in Fig. II make it possible to find directly the lift coefficient given by formula (3). This lift co- efficient should be corrected for humidity and superheat as outlined above.

(b) Lift Vari2tions The table below gives a number of rules which permit keeping track of lift variations after take-off.

EFFECT ~ oF VARIOUS ATMOSPHERIC CONDITIONS ON GROSS LIFT CONDITION EFFECT ON GROSS LIFT Below Above Pressure Height Pressure Height Increased Altitude, NONE Reduced by 1% for Decreased Barometric every 360 ft.or Pressure • 3 in. Hg. * Decreased Altitude, NONE

NONE **

Increased Barometric Pressure.

Decreased Ambient NONE

NONE **

Temperature, No Superheat Increased Ambient NONE Reduced by 1% for Tempe Pa ture, No

every 5o F. *

Superheat.

Pqsitive Superheat Increased by 1% for Increased by a neg- ligible amount.

every 5° F. *

Negative Superheat Decreased by 1% for Decreased b~ 1%

every 5° F. * for every 5 F. **

* For the K-ship, 1% of gross lift amounts to about 250 lbs.

Superheat can be seen, therefore, to affect lift by about 50 lbs. for every 1°F., or 90 lbs. for every 1°C.

** Gas contracts and ship is no longer at pressure height.

-9- NOTE: The student pilot is sometimes confused by the apparent contradiction between some of the above rules, which seem to imply that lift is unaffected by temperature, and the known fact that an airship has a greater lift in winter than in summer.

The contradiction is easily cleared when it is considered that the rules in the above table apply only to the lift of an airship to which no helium is added.

It is true, as indicated by the above rules, that the lift of an airship inflated during the summer remains the same when cold weather sets in, pro- vided no gas is added and no gas is lost and neglect- ing the . effect of humidity. The gas and the dis- placed air contract in the same proportion so that a like weight of gas has th .e same lift in winter as in summer.

At the same time, because of the gas contraction, it is possible to add a certain amount of gas in winter to a ship which had been fully inflated in the sum- mer. A fully inflated ship has, therefore, a greater lift in winter than in summer.

(2) Static Trim An airship trims at an angle such as to bring the center of gravity directly below the center of buoyancy. The K-airships trim at an angle of 3.5°,plus or Ia.inus 1/2°, nose down at static equilibrium, when . fully inflated, with con- ditions such as to produce a static lift of 62 lbs. per 1000 cubic feet and with a load distribution as indicated on the following page.

Under the above conditions, the location of the center of buoyancy and of some of the important centers of gravity along the longitudinal axis are given below: -10- Center of Buoyancy: 20.53 ft. Aft of Frame 9.

Center of Gravity of Ship as a whole: 1.75 ft. Forward of Center of Buoyancy.

Center of Gravity of Loaded Car. 8.45 ft. Forward of Center of Buoyancy.

Center of Gravity of Envelope: 10.00 ft. Aft of Center of Buoyancy.

The useful load is ordinarily distributed approximate- ly about the center of gravity of the car so that changes in the useful load do not alter greatly the location of the center of gravity of the car.

The center of gravity of the ship as a whole, however, changes with the total car load since, as indicated above, the center of gravity of the car is considerably forward of the center of gravity of the envelope which makes up the balance of the gross load. An increase of car load has the effect of moving the center of gravity of the ship forward and of increasing the nose down angle. A decrease of car load has the effect of moving the center of gravity of the ship aft and of decreasing the nose down angle.

A change of 10,000 ft. lbs. in the moment balance with respect to the center of buoyancy of the ship, whether caused by a change of total load or by a change of load distribution, alters the static trim angle by about 1°.

-11- Since the trim angle is measured at full inflation and at equilibrium a change in the lift coefficient must be accompanied by a corresponding change in the car load to maintain equilibrium. Therefoxe, when the lift is greater, the load will also be greater, and the ship will trim at a greater nose dovm angle. A difference between the su~ner and winter trim angles may be observed because of this factor.

At less than full inflation the trim of the ship is affected by the above factors, and also by the relative inflation of the ballonets.

(3) Dynamic Lift The dynamic lift of an airship is the lift which de- pends upon the forward motion and the angle of attack of the ship with respect to the air. See Fig. III for dynamic lift at various forward speeds.

The curves plotted in Fig. IV show the variation of the minimum length of the take-off run of model K-airships with heaviness and head wind.

The assumptions on which the curves are based are n~ither exact nor invariable, but they are on the safe side, giving an over estimate rather than an under estimate of the required length of the take-off run.

(4) Factors of Safety The suspension system and the car structure of the K- airship are designed for a total car load of 16,000 lbs. The I / minimum factors of safety at this load are 3.00 for the car structure and 4.00 for the car suspension.

-12-

Next: LexTest_2014_08_18_07_24_42_714 →

LexTest_2014_08_18_07_24_42_714

-9-

·-- ---- --.--- ---------.-----,-----.-----------r----------:---------,.------r· · ~--~-----~--------- ... --~--~- .. --------~---,---------.-.--........_. ______ _ ______ .._ ___ _,___ __ , _______ .... ~---- ----;-------- --- ·t·· ------ -· ----------·- ____________________________ j__ --:-----l---·------·------i --- -· ··--·-··------. --- 90· ---~-- f / - -- - -- --- ---- -------- ..•.

--------_...---------------------~---------,.~----'"-·-----~------~--.-----_...-.------------.----;--- ... --------- ..... - ---~----~----· 80 -----------·--·-------------------·-· . _______________ , _________ ..._ __________ _ ELt;. _ IJJ: ·- ·- ---------·- -----1 - -··--- .. ·---~ __________________________ .... -------=~---=-~~--- /I'l&AMZC: -~~-~~------- ______ L__~

l/FT . CHA - RT - ---.- -·--- i

70 I - .. 0 , v L. L..

--·----·-

- ------------------ --- ---- ---- ~- ... ·--------------- ----·- _......_ ____ _ ._-.)

-o--__ " ...

____ , __ __ . -- .. - -· -- -·- -- .---- - ' . .

0.7S Fi.JL.L.. POWER -· ------ -··-"""---· - ---~·----·- --~----·------ - -·- .;.... .. _.,__, __ ,. _____________ _,_.

·-· .... ~~---- -- - -~· ~-- ---- ... ·-·-·-----~ ----'"1 DYNAMIC LIFT VS. VELOCITY AT IIARIOUS ANGLES OF ATTACK AND VARIOUS HORSE POWER) I<- TYPE AIR SHIP VALuEs BAseD ON K-13 FLIGHT TEsr VALUEs . BAsED ON /VJ-1 Moe>EL TEsr 0 ------------------------------------------

1000 zooo 3000 5000 7000 8000 10000

0 4000 9000 11000 12000 D} !]M I C L IF T ( P 0 UN D S) ~ ..

------- - 13-

Next: LexTest_2014_08_18_07_27_02_008 →

LexTest_2014_08_18_07_27_02_008

1000 r--\----+VARIATION OF MINIMUM LENGTH OF TAKG'-OFF !?UN WITH HeAVINESS AND HEAD WIND .....

BOO

~

FIGURE lY- ~

TAKf-Off CHART

from Bureau o{ Aeronautics

~

(( SERVICE BULLETIN No . 60

~

I soo

~

~ ~ zoo s /0 15 20 2S 30 3S 40 H£AD WIND KNOTS · -14- (5) WEIGHT EMPTY Note: All weights are for ships before K-75.

· ENVELOPE GROUP Main Envelope Fabric ••••••••••••••••••••••••••••• 5670.4 Lb s .

Ballonets ...........................•. ~ ......... .

820.0 Air Lines ...•....................................

195.3 Frames •••••••••••••• ~............ 85.7 Lbs.

Fabric Patches & Lacing •••••••••• 109.6 Rip Panels, Complete with cords •••••.•••••••••••• 21.1 Car Suspension •••••••••••••••••••••••••••••••••• 778.5 Inside Catenaries ••••••e••••••••• 524.0 Inside Cables .•••••••••••••••••• 129.6 Outside Catenaries ••••••••••••••• 102.2 Outside Cables •••••••••••••••••• 22•7 Gas Valves & Reinforcement ••••••••••••••••••••••• 68.0 Air Pressure System •••••••••••••••••••••••••••••• 6.0 Air Valve Reinforcement •••••••••• 6.0 Bow Stiffening ................................. .

693.3 Bow Cone ••••••••••••••••••••••••• 106.8 Batten Patches, Laces, Etc. • •••• 102.0 Battens ........................ .

378.0 Batten Cables ••••••••••••••••••• 28.6 Mooring Cone Spindle & Pendant ••• 45-4 Miscellaneous •••••••••••••••••••• 32.5 Handling Lines ••••••••••••••••••••••• ..... . .....

137.2 Drag Rope •••••••••••••••••••••••• 18.5 Yaw Lines •.•••••••••••.•••••••••• 39.9 Handling Lines, All Others ••••••• 78.8 Fin Suspension, attached to envelope ••••••••••••• 145.6 Lighting & Bonding System ••••••••••••••••••••••• 20.5 Car Fairing, Tape Lacing Cord & Padding ••••••••• 31.8 Miscellaneous equipment, patches, manholes and sleeves attached to the envelope •••••••••••• 301.6 TOTAL ENVELOPE GROUP . .. . .. ........ .. . .. .. .. .

8895.3 Lbs.

EMPENNAGE GROUP Upper Fin ••••••••••••••••••••••• 241.0 Lbs.

Horizontal Fins (2) ••••••••••••• 482.0 217.0 Lov1er Fin ................ · . · · · · · Upper Rudder •••••••••••.•••••••• 86.0 Elevators (2) ••••••••••••••••••• 172.0 Lower Rudder •••••••••••••••••••• 56.0 Fin Brace System •••••••••••••••• 100.0 TOTAL EMPENNAGE GROUP ... . . . . . ........ . . ... .

1354.0 Lbs.

TOTAL ENVELOPE & E1IPENNAGE •••••••••••••••••• 10,249.3 Lh~.

-15- WEIGHT EM PTY CONTROL CAR GROUP Car ································L··········· 2250.0 Lbs.

Framework •••••••••••••••••••••••• 1056.0 Lbs.

Metal Skin & Skin Stiffeners •••• 436.6 Fabric Covering •••••••••••• • •••• 5.6 Windows ••••••••••••••••••••••••• 120.1 Doors Complete •••••••••••••••••• 61.1 Handling Boxes and Doors •••••••• 9.5 Bomb Hatch Doors & Opening M ech. 44.6 Rand Rails a nd Brackets ••••••••• 32.7 Insulation & Comp a rtment Pa rtition 33.8 Flooring & Supp orts •• • • • •• •• • • • • 322.6 Access Ladders if carried in flight 16.8 Miscellaneous ••••••••••••••••••••• 110.6 Landing Gear Landing Wheel As s embly ••••••••••••••••••••• 228.5 Lbs.

~beel & Tire •••••••••••••••••••• 77.5 Lbs.

Fork and Axle ••••••••••••••••••• 45.9 Shock Absorber •••••••••••••••••• 43.6 Retracting M echanism •••••••••••• 37.5 Miscellaneous Installation •••••• 24.0 Outriggers & Engine Nacelles ••••••••••••••••••• 741.1 Lbs.

Structure •••••••••••••••••••••• 250.0 Lbs.

M e~l Skin & Skin Stiffeners •••• 151.5 Engine M ounts •••••••••••••••••• 78.8 Cowliz.!gS • • . . . . . • . . • . • . • . . • • • • • • 95.0 Engine Nacelles & Stiffeners •••• 165.8 Power Pl a nt Group •••••••••••••••••••••••••••••• 264 2.8 Lbs.

Engines (as installed) ••••••••• 1858.0 Lbs.

Engine Accessories ••••••••••••• 238.1 Power Plant Controls ••••••••••• 39.9 Propellers ••••••••••••••••••••• 422.8 St c> . rting System • • • • • • • • • • • • • • • • 84.0 Lubrication System ••••••••••••••••••••••••••••• 154-3 Lbs.

Tanks & Protection, Installation 44.1 Lbs.

Oil Coolers •••••••••••••••••••• 60.5 Pum p s,not integral w ith engine 4-5 Pi p ing, etc. •••••••••••••••••• 45.2 -16- WEIGHT EMPTY .Fuel System ..•••••..•••••••.•• ~ ..•.•••.••..•.•.• 548.0 Lbs • Tanks & Protection, installation Pumps, including transfer pump &.

hose •••••••••••••••••••••••••••• 314.4 Lbs.

Piping for Fuel and Vent Systems 233.6 Fixed Equipment ••••••.•••...••••••••••••••••••.

2050.9 Lbs.

Instruments •••••••••••••••••••• 127.2 Lbs.

Major Controls, complete ••••••• 125.8 Minor Controls, complete ••••••• 42.5 Pressure Tube Assembly ••••••••• 32.6 Electrical ••••••••••••••••••••• 624.8 Communication (Radio & Radar, MAD, IFF) ••••••• 1098.0 Furnishings •••••••••••••.••••.••••••••••••••••.

466.9 Lbs.

Personnel ················~····· 287.4 Lbs.

Einergency • • • • • • • • • • • •.• • • • • • • • • • 47.4 Chair Base in Aft Section •••••• 3.2 Navigator's Table •••••••••••••• 19.9 Radio Table •••••••••••••••••••• 26.7 Heating Equipment •••••••••••••• 33.0 Car Ceiling •••••••••••••••••••• 27.3 Rigger's Cabinet ••••••••••••••• 15~0 Navigational Gear Rack ••••••••• 5.3 Miscellaneous •••••••••••••••••• 1.7 Air System . ........... . ... . ... . ... ... .... .. .. ..

352.8 Lbs.

Auxiliary Power Plant 200.3 Lbs.

• • • • • • • • • • • • • • • • • • • • • • • • • • TOTAL CAR GROUP . .... .. . . . .

9635.6 Lbs.

-17- USEFUL LOAD (6) ~ Crew (10 Men at 175 lbs. each) 1750.0 Lbs.

• • • • • • • • • • • • • • • • Fuel - Main Engines &: Aux. Engines • • • • • • • • • • • • • • • 3930.0 Lbs .• Overhead Tanks 475 Gal.@ 6#/Gal. 2850.0 Lbs.

Slip Tanks, 180 Gal. •••••••••• 1080.0 Oil - Main Engines - 52 Gal. @ 7.5# Gal. 390.0 Lbs • • • • • • • • Aux. Power Plant, 3 Gal. @ 7.5# 22.5 • • • • • • • • • Droppable Fuel Tanks (2) . . . .. .. ..... .. .. ~ .. .. . 42.1 Lbs.

Baggage . .. . .. . . . . .. . . .... . .... . ........ .. . . .. 00.0 Lbs.

Cargo .. . ... . . .. . . ........ . . . . . . ... . .. . . .. .... 00.0 Lbs.

Armament .. . . . . ... .. ...... ... .... .. .. .. ..... . .

1620.0 Lbs.

1. 50 Cal. M.G. . . .... . . ... . . 105.0 Lbs.

2. M.G. Ammunition . . ..... . . . 132.0

Bomb Racks .. . ..... .. .

3. 41.6

Bomb Racks .. .. . .. . ... 41.6

4· 5. Bombs M-17 650.0 • • • • • • • • • • •

6. Bombs M-17 . . . .. . ..... 650.0

m

Equipment . . . . ~ . .. . . ... . ... .. . . . .. .. . . . .. . .... 570.3 Lbs.

Navigation Gear a. Charts, Publications •••••• 7.5 Lbs.

b. Optical Drift Sight ••••••• 13.5 c. Wiley Drift Sight ••••••••• 1.5 d. Parallel Rulers, Binoculars, 14.0 Stop Watch, Dividers ······• e. Miscellaneous Gear ••••••••• 18~5 Total 55.0 Lbs.

Photographic ••••••••••••••••• 55.0 Lbs.

Pyrotechnics - a. Signal Pistol ••••••••••••• 2.1 Lbs.

b. 24 Rounds Signal Flares •••• 7.2 c. 24 Float Lights ••••••••••• 52.8 48.0 d. 24 Bronze Powder M arkers . · · Total 110.1 Lbs.

-18- USEFUL LOAD Emergency Life Saving Equipment: a. Ten Life Jackets@ 3# •••••••••• 30.0 Lbs.

b. Life Raft •.•••••••••••••••••••• 66.0 Total ••••••••• 96.0 Lbs.

Food and Water: a. Food, Canned . . ... ... ... . ....... 30.0 Lbs.

b. Food, Fresh .... . . . . . . ....... .. .

55.0 c. Water, Fresh . .. . . .... . . .... . . ..

35.0

d. Rescue, Rations . ....... . ... ... . 16.0

e. Emergency, Food and Water .. . . . . 27.0

Total 163.0 Lbs.

Miscellaneous Equipment: a. Classified Container ••••••••••• 2.2 Lbs.

b. Emergency Cable •••••••••••••••• 5.0 c. Two Flashlights@ 3/4 Lbs. • •••• 1.5 d. Signal Flags ••••••••••••••••••• 1.0 e. Fuel Pick-up, Green Marker Buoys, Grapnel . ...•.•...•.•.......••....

28.0 f. One (1) Chute, One (1) Harness •• 18.0 g.. P. & W. Engine Kit ••••••••••••• 15.0 h. Wire Cutter and Knife •••••••••• 5.0 i. Rigger's Kit ••••••••••••••••••• lh2.

Total 91.2 Lbs.

TOTAL USEFUL LOAD 8325.1 Lbs.

-19- It is recommended that the total car load be not allowed to exceed 18,300 lbs., or 2300 lbs. over the design Under such condition of 2300 lbs. "Design Heaviness" the factors of safety are reduced to about 2.6 for the car structure and about 3.5 for the car suspension.

NOTE: "Design heaviness" is the excess of car load over design load - a.nd should not be confuseq. with "flight heaviness" which is the excess of gross load over gross lift.

"Flight heaviness" alone is no measure of the factors of safety of the car structure and suspension.

Under condi tiofls of high lift there may be no "flight heaviness" but a high "design heaviness."

Under conditions of low lift there may be no "design heaviness" but a high "flight heaviness."

Preceeding pages show computations of a typical car load. It is suggested that similar forms be used for actual computations before take-off.

-21-

Next: LexTest_2014_08_18_07_32_06_131 →

LexTest_2014_08_18_07_32_06_131

B. ENVELOPE PRESSURE CONTROL SYSTEM (1) General Description The maintenance of a predetermined pressure differ- ential between the gas in the envelope of a non-rigid air- ship and the surrounding atmosphere is the first basic requirement to the successful operation of this type of airship.

The functioning of the envelope in assuming the various flight stresses, the proper suspension of the car, the effic- ient operation of the controls, all depend upon a closely held pressure differential.

It is the function of the pressure control system to maintain this pressure differential within a certain range and to do this with a minimum loss of lifting gas. This result is accomplished by inflating the envelope partly with gas and partly with air, the air being contained in a forward and an aft ballonet, and by regulating the inflation of the air by means of an air system,without changes to the amount of gas in the envelope. Under extreme conditions, outside of the range of the air system, gas can be released auto- matically by meatls of two gas valves to prevent the internal pressure of the envelope from rising above a safe value.

The pressure control system is also used to adjust the trim of the ship by regulating the relative inflation of the two ballonets.

-22- (2) Air System The air system comprises a forward and an aft ballonet, a system of scoops, ducts, valves and air chambers.

Air is taken in at scoops located in the port and starboard motor outriggers and is led through a check valve of the butterfly type into an air chamber. From this chamber, two air ducts lead, one to the forward and the other to the aft ballonet, through ma~ually controlled dampers. An automatic valve is connected to each ballonet system and is set to release air automatically when the pressure reaches a pre- determined value. In airships K-3 thru K-98, a blower with a gasoline power plant is provided in the cabin to supply pressure to the air system when the pressure from the regular system becomes inadequate. In airships K-99 and future, an electric blower is provided. The construction of the system is described in full detail in the "Descriptive Specifications Manual." The operation of the system is considered further below: (a) Scoops As mentioned above, air is collected by scoops located in the port and the starboard outrigger and is led to an air chamber through check valves. This air chamber can be con- nected to either or both ballonets by means of two manually controlled dampers. The air pressure in the ballonets can be adjusted within certain limits, as described further on, by regulating the opening of the scoops.

-23- ......

AIR INTAKE AIR DISCHARG E Flg. -v AIR PRESSURE SYSTEM K-3 thru K-'98 Fig. VI Air Scoops (b) Valve Settings (See Buaer Manual 12-304) The pressure in the forward and aft ballonets is limit- ed by the forward and aft automatic air release valves. These two valves are set to operate at different pressures for reasons that will become apparent further on.

The valve of the forward ballonet is set to start open- ing when the air pressure in the forward ballonet, as read at the car manometer, reaches 1.50 inches of wa ter. The valve of the aft ballonet is set to begin to open at an air pressure of 2.00 inches of water.

When the ballonets are partly infl a ted there is a difference of pressure bet • N een the a ir in the ballonets and the gas in the envelope.

This difference depends upon the -25- ·r--·-----r-- -r-- - 1 ----r--~--~--~------r-----~------~---,--~--~---.~-~--~--- t .

I . • 1 : ; ' l : ; ! • i ' ! ' ; ' l , l .. _____ _L ____ . ____ _j __ ~_j_,t ------- i -; i=--:·-----1~--_l _ _;__L ___ -·-----~--·-:-t-~--t -- :1

. I . ' I I t l I ! I l I ! j I I ' i

. t I i I i I j ! 1 I t J t . . . t I 1 • ' I J ~---.:.-r--~- -~-t---r-~-- ~--i--t-----+- . -r --,:-- -~---+ --+ -r : ____ t --r -----r--+- -+:-- ~ -~. -: I l ' . I I i ! . I ! . I ' f . ! ! l ' l I I ~1 ' ' 'til'·· i I I -r--r- 11' j · I i l I l i ' ' i i i i ! I l i ! : I I : j ! ! .

t~-----~--1_ __ _ . __ ....:!------....!·--·--.J----L--'---j___l_--...!..-__l _ __ t _j __ , ___ _ ! _..t_...i_ __ j _____ J __t_...l_ _• __ ! __ ! _ _j i I ! . i I I I ' i I I t 't ' I . 1 1 l i ) ! l · ! ! 1 I 1 ~ j · l

r--- I i ' 1 l I I -;---r-- . ! ! ~ I I

.·---,--- · ----.- j __ i--+-~--4-~-+-~~_j __ l .. _~ ___ .. L_j ___ ~---l-l_j _ _ J __ [ ! ~_j

I . l l ! j : • . ! I I : ! : I . I I l I : !

: . I .s i ' : ~ i • I ! i I I • !' i I I j__j

I • I . l I i : i 't l i : t I l 1 i . I ! l l r 1 ' i .... 1 I I ' t i ' r t I _ 1 , ' -- ·----L---'-- -- -7---r- --:-- ~'--t--j-~'- {-- ;. .. -+-----1-+--•-- -t---t -- -:--+--:-.........;--;---L_~- ~.--: ' [ l l ' j ! l i ! ; 1 1 I ! ! I j : ! i I !

• . . - 1 1 : ~, , 1 , ~ . 1 . , I 1 r 1 • 1 : : j , . ' t ' ' ; ' · ' i . i ! , ' 1 ! ~ i ' I ! . I l : .

:- ~ -~---~- ~ - -- ·-- -- .. -~-: -T- -:--,- -:-,-:r--~-- r: ~ lr-r-: - -·T i 1 - ---~~--1- ~- - ~ r t;J ·- -- . -f , • : • ---,-- ·~ ' . ~ t I 1 1 1 I • I I I l ' l. ' ' !' I 1 ' 1 I l . ' ' . l I ~/) I I ' ' • ' I • ' ... I ! l I t L . . I I li ·--r ~=- ;--t·--: -+i ---;--1--;_JI - ~-i~.-----~ Zi iT_i __ l_;---r---~- --~-:-i 1 : ., ~

! C/1 l l : l ! i ! i ; I l : l l ' ! . i I t 1 : : i

.::;:. ---- --- -· --------- -- -- -~- ---. - -- -- -_-- - - -'-----~---r ___ j __ - --l- · -------- -~-J - ----r---- -;--- · ··r·--- --- -r-- -~-~---·-i-- -- :---- -;

L ~ .3 __ · _ _ L_j __ _l ..,! __ _j t- ' . ..:.. ! : t : ! -t-t-1· ! l

' ~ · ' j ' I . j . I • · i - I : I . ' '

o~ i · t · ; ! : ! 1 : t j ~ ~ I ! r i , j • ! ~ C/) -- ~ --r-- -~- -------1--+-- 1 1 i r-;-J+----~--:---1 -r---r--~-~---~---t--:---r---~--~·-:·----~

~ ... CIJ -- ~ --- ·-- -~ l : __,._ I I ~-L--: --'--+-L~ ' ; ~ I ~ I . : >

~ ! i ! 1 : !' I • ; l i l. I ; I i j !' : l ' I ! l u I I • 1 ' I • I I • I I I : • . I !

.- &1 ·- ~ -r-- 2 - --.- - --:~--y·-:- - ... --~·--T--• -r--~--r-:---r-r---r--~~----:--t--·--:---r--·---+- . --:-1

l--·-- ·" ... ..L_ -- · --- -- i . - _ I' l I • !. -'-...;_+--L l : I II ! _L_ . . i

z VJ ; 1 1 -j. l ; 1 ! 1 . i : l i 1 i r 1 ~ - ~ -- --· .... --- ····-~---·-- ----~-1--L .. +--i---r---L .... J ... -i--+--)----i~- .L ..... +---L .. -;----·'-----+-----·- ~----'--

, P'1 ° I : f ! : ' : I i I i I ! I I f . I !

' 0:: ;z; ' · ; ' ! · t · • j .---!.-. _1 , . j ·- ::s H --r---- ---·~. - l i ; --:---;~--;- I ' -r- -l ~ __ ; · - ---~--- --~----l..----~- .. ! --+-L _j ___ j __ .. ~----~---L - -+ · ~ ---:-·-----~-------+---' -~; ~ ,1 : l ; i ' l ! :_j_ i l . I : - p:. ·---· -- -.----r-----t • I ' ~............., .:.............

I l : ' t l I 1 • • . ' f"'r 4 ·- j - _ _t ___ ----~-- --1--~-~--..:.. ' t ; ; .. ---! -- • - i ! ' I ~ --- r : ~ . 1 , 1 • l-~-1---;·--r--:- : ~ ·-;--·-- --·r·- - . __ -- __ ---1 _- _ -_-_- _ -_-~-~--- · - _ -.:..--_ .. _- .... -; -- -- - ____ ! _____ --- -- T-~---r~-l-~ :~ ~--- c-. --l~-i.~] ___ ;=1~- :~ j __ -=-- ~-- -~ +----- ~ _ -·---"

L----- ....... J Q _ . I i ! I . ; i

' i ; ' ' \ ~ t J !

, --- 1 0 - - 20 30 ·-~· 40 --·-- 50 · 60 -- 70 -- BG -~- 90 --· 1 00 - ,-----~-,--- , --- - _ __ ___ :_ . _____ ; --~-_j_-~ __ j__ ________ L --~--- _; ___ · __ l ____ i_~ __ t _____ : _j ____ ~ __ . __ : --~-----; --~-~-~ j ! l ~ - - -L--·---·--- ___ l - - ~ - FULLNES S , OF BALLO NETS ---~----'·---;~-- '· I I • t ; l l . ; ' .

+-·---· ------·----------------· _f____ ----~""--- .. -~---'------------ ---- --·------~ Fig. VII ·-- ------~·----~-----"': ______ ... ___ __.. ..... -- . ---- ------ - AIR PRESSURE IN EXCESS OF GAS PRESSURE vs -- % FULLNESS OF BALLONETS AT ZERO - PITCH ANGLE AT STANDARD UNIT LIFT CONDITIONS -26- height of the upper part of the fabric of the ballonets or upon the degree of their inflations, upon the lift co- efficient of the gas, and upon the f~bric weight which reacts on the air.

Curve in Fig. VII shows the relation between this difference in pressure and the inflation of the ballonets at standard lift coefficient. It will be noted the.t the difference of pressure is about 0.50 inches at full infla- tion and nea~ly zero when the ballonets are fully deflated.

Since the automatic air valves are operated by the air pressur~ in the ballonets and not by the gas pressure, it will be obvious that the system will tend to regulate for a higher gas pressure when the ballonets are empty than when they are inflated.

(c) Pressure Regulation Under normal flight condition a gas pressure of about 1.5 inches of water should be maintained with a maximum vari- ation of 1.25 to 2.00 inches.

CAUTION: Under no condition should the pressure be allowed to go lower than 0.5 inch or higher than 3.0 inches of water, the lower pressure being permissible only in landing operations or in the hangar when there is little or no forward speed.

It is particularly essential to maintain an adequate internal pressure when the ship is operated at high speed or when moored at the mast during high winds.

-27- The K-airships are designed for a maximum speed of 65 knots with an internal gas pressure of 1.5 inches of water.

Since the automatic air valves, as . pointed out above, are operated by the air pressure of the ballonets, the corresponding gas pressure at which they open depends on the gas inflation of the ship. If, for instance, the ship is 85% gas inflated and the ballonets are more than half infle . ted, it can be seen, by referring to the curve in Fig. VII that the gas pressure in the envelope is about 0.32 inches of water less than the air pressure in the ballonets. The air valve of the forward ballonet will open, therefore, at air pressure of 1.5 inches of water, while the corresponding gas pressure is .32 inches of water less than the setting of th~ gas valve or 1.18 inches.

It will still be possible, however, to maintain the recommended operating gas pressure of 1.5 inches of water by opening the forward air damper and regulating the scoop opening so as to produce air circulation through the air damper and the partially opened air valve.

The matter of the proper regulation of the air CAUTION: scoops is of the utmost importance. If the scoops are opened too wide, excessive pressure may be built up in the envelope causing loss of gas. If the scoops are not opened enough, the gas pressure may drop to a da ngerously low value resulting in buckling of the envelope.

-2 8- With the differential valve setting outlined above, it is apparent that as long as the ship is operated below the pres s ure height of the forward ballonet, air is re- leased only from this ballonet w hen the altitude of the ship is increased. Hence, if upon de scending, the pilot operates only the forward damper, the air which has been valved out during the ascent will be replaced to the for- ward ballonet, thus restoring the trim of the ship to the same condition that exi s ted at take-off.

During short flights, the oper a tion of the system is automatic, and no manual adjustment needs to be m ade except to open the forward damper. During long flights, occasional manual adjustments of the air balance m ay be necessary, but the system remains largely self-operating.

(d) Air Valve Adjustment All valves are adjusted to their specified settings and t e sted before being inst a lled in the airship and re- tes te d after installation.

The valve settings should not be changed unless diffi- culties arise. Adjustments should then be made only by a qualified person. During emergency, it may be necessary to adjust the valve in flight. Instructions below should clarify any difficulties that may be encountered.

-29- Two 36~inch diameter air valves, see Fig. VIII and IX, are provided in the air line in the top of the car structure for valving air from the ballonets. One of the valves is located between Fre~es 4 and 5, and valves air from the aft ballonet, the air going out through louvers on the port side of the car. The other valve, located between frames 6 and 7, valves air from the forward ballonet and exhausts air on the starboard side of the car. Control lines for opening and closing the valves extend to Pilot's Instrument panel, see Fig. XI, Page 42.

The air valves are set to open as follows: Aft Valve - Forward Valve - 1.5" H 0 To adjust valves on K-3 thru K-53, exclusive of K-49: (1) Inside knob adjustments (Three) Break seal on each valve adjustment knob.

Apply same number of turns to each knob.

Never adjust one or two knobs, but a djust them all equally, to prevent warping and improper seating.

(d) Do all loosening and some tightening on the inside.

(e) Turn adjustments clockwise to tighten or increase opening pressure.

(f) Turn adjustments counter-clockwise to loosen or decreas - e opening pressure.

(g) Re-seal valve adjustments to p revent valve frbm losing its settin~.

-30- Fig. VIII - 36" Air Valve · K-3 thru K-53, Excl. of K-49 -31- (2) Outside Gear Adjustments Remove gear cover.

Remove cotter pin (through gear).

Do most tightening on outside gear and no loosening.

(d) When tightened until 2-7/8" of screw pro- trudes from the gear, the forward or aft air valve opening point will increase 7/16" H20. This is a maximum condition.

(e) Turn counter-clockwise to tighten or increase opening point.

(f) Turn clockwise to loosen or decrease opening point.

(g) Replace cotter pin and gear cover.

In the event the valves are completely out of adjust- ment, then proceed as follows: 1. Set outside gear adjustment to neutral setting.

NOTE: Neutral setting is defined as 1-1/2" of screw protrusion from gear. Total length of screw is 3 inches.

2. Build up air pressure to 1.5" H20 at the manometer in the car and adjust inside knobs as previously described.

3. The valve is considered in adjustment when the dome begins to float freely and emits a characteristic hum.

4· Re-seal all adjust m ent knobs and replace outside adjusting gear cover, together with the cotter ~in.

Insofar as the aft valve is concerned, build up air pressure to 2 inches and repeat the above procedure.

To ad.iust valves on K-49. K-54 and later airships: Open the zippers for the access openings in the ceiling of the car and remove the lock seal attached to each knob.

Unscrew the l/2tr O.D. sealing c a ps and turn adjusting knobs.

-32- Give each of the knobs an egual number of turns and in the same direction. Turning the knobs clockwise, or to the right, inc~eases the pressure necessary to operate the valve. Turning the knobs counter-clockwise, or to the left, lowers the pressure necessary to operate the valve. Tests conducted on a number of modified valves in a valve test chamber determined that ten complete turns on each of the three knobs changes the pressure setting necessary to oper- ate the valve by 1/5 of an inch of H 0.

After a satisfactory resetting is found, add. leather washers and screw the sealing caps in place again, then safety the knobs to the clips on the shield. Test setting against the air manometers. The use of the gas manometer is misleading, except at, or very near, pressure height.

-33-- Fig. IX - 36" Air Valve K-49, K-54 & Future -34- (e) Take-Off Y v 'hen the ship is in the hangar it is norl!lally J..cept under proper pressure by m eans of a ground blower. As the ship is taken out of the hangar, v ; ea ther condi tion3 ma y be such as to cause a change of the temperature of the gas.

If the temperature is increased, air will be released automatically by the air valves. If the temperature is de- creased, air may have to be blo~~ into the system to keep up the pressure. This may be done by ope ning the scoops and the a ir dampers, and speeding up the engines or it may be done by means of the auxiliary blower.

The dampers can be kept continuously open w hile NOTE: air is blown occasionally in the system by man- euvering the throttles, the check valves pre- venting loss of air when the engines are idle.

Under normal conditions, however, it is best to keep the dampers closed when not pumping air.

(f) Climb As soon as the ship begins to rise, the problem is no longer one of feeding air to the system, but one of releas- ing air to maintain a constant differential pressure between the gas in the envelope an.d the decreasing atmospheric pressure.

This is done automa tically as outlined above, by the <>-ir valves. The air valves and ducts can prevent the pressure from rising above 2.5 inche s of water when the ship is rising a t a speed of 2400 ft. per minute.

-35- During the climb both dampers should be closed. The scoops, however, should remain open so that the p ilot may be able to blow air into the ballonets by o pening the dampers, should he decide to come do~m again .

CAUTION: 2400 ft •. per.minute is the maximum permissible rate of climb. The actual rate of climb should be kept wel l below this vaiue.

(g) Level Flight In level flight it is common pr2 . ctice to keep the for- ward damper and the scoops open so as to produce an air pressure slightly higher than the setting of the valves, causing a circulation of air through the air damper and the air valve.

CAUTION: The air release valves should not be opened manually when the ship is flying near or above pressure height.

A warning to this effect is mounted on the p ilot's instrument panel. As long as the valves are opere>.ted auto- rna tically, with the scoops and air damper opened, pre :: ; sure in the system d oes not drop below the setting of the valves although the ballonets may become completely deflated. If the air valves were opened manually at this ' point, the small amount of air in the system would become q uickly exh e. usted, the pressure dropping to atmospheric pre2sure. The 3 ir line pa tches or the air line frame may be dam a.ged by the full unbalanced gas pressure.

-36- (h) Descending When the ship is descending, air must be fed into the system to maintain the differential pressure between the inside of the envelope and the increasing atmospheric pressure. The scoops should be opened wide enough to per- mit adequate air flow. The air scoops, ducts, and damper valves can admit air into the ballon e ts at a sufficient rate to maintain a gas pressure of 1.25 inches of water w hen the shi p is descending at a rate of 1200 feet per minute, at a forward speed of 50 knots.

The air intake capacity naturally decreases as the forward speed is reduced so that the maximum permissible rate of descent is less than 1200 feet per minute when the forward speed is less than 5.0 lrnots.

CAUTION: 1200 feet per minute is the maximum permissible rate of descent. The actual rate of descent should be kept well below this value.

(i) Landing At the time of landing it _ usually becomes necessary to throttle down the motors and the air scoop system can no longer supply the required pressure to the ballonets. An auxiliary blower is provided for such conditions.

The blower is of sufficient capacity to maintain a gas pressure of 0.5 inches of water at the gas manometer -37- when the ship is descending without power at the rate of 250 ft. per minute. This pressure, while inadequate for normal flight, is sufficient to permit satisfactory hand- ling of the ship during landing operations.

Instructions for starting the blower for airships K-3 thru K-98 are given on p~ _ ge 44.

(j) Shifting Air During flight, it may bec. ome necessary to adjust the relative inflation of the two ballonets · in order to change the trim of the ship. This is done by operating the air valves and dampers manually.

In trimming the ship in this manner, it may be well to consider air as ordinary ballast, the effect of transferring air being the same as that of transferring any ballast.

(k) Blowing Air Into The Gas In emergency cases where a large amount of gas has been lost, such as when the ship is descending after having over- shot its pressure height, and the ballonets, even when fully inflated, cannot keep up the . pressure of the envelope, it may become necessary to blow air into the gas.

This may be done by untying the sleeve connecting the air chamber to the envelope. This sleeve is located above -38- the cabin ceiling, starboard, and makes a nyn connection with the helium inflation sleeve. Only the amount of air necessary to bring the pressure to th~ required value should be used.

(3) Gas Release System (See BuAer Manual 12-304 12-307).

The gas release system includes two 20-inch gas valves, located on the port and starboard sides of the envelope at panel 34, and gores K and .L. It includes, also, two rip panels located on the top of the ship from panel 21 to 28, and from panel 53 to 59.

(a) Gas Valves The gas valves are set to operate automatically when the gas pressure reaches 2-1/2-inches of water as read on the gas manometer. They can also be operated manually from the pilot's instrument panel. The gas valves are equipped with micro switches which operate telltale lights on the pilot's panel when the gas valve begins to open at 2-1/2-inches of water. In order to offset localized drop of pressure in the air stream and to prevent premature opening of the valves, a semi-circular windshield is attached to the envelope on the aft side of the . valve.

CAUTION: Do not attempt to hold gas valves closed manually when . flying above - pr . essure height as _ excessive pressure maY deYelop in the envelope.

-39- Fig. X Helium Inflation Sleeve -40- (b) Rip Panels The rope which opens the forward rip panel can be reached from · the forward door; the rope which opens the aft panel can be reached from the aft door. They are dyed red to avoid confusion with the other ropes.

(4) Controls and Auxiliaries

(a) Valve Controls The air and gas release valves can be operated man~ ually from the pilot's instrument panel, Fig. XI. Every valve has an opening arid a closing control. Pulling the opening control lifts the valve off its seat and releases air or gas as the case may be. The valves should close by themselves when the opening control is released.

A closing control is p rovided, however, to force the valves closed in case they should stick. The control is also used to make certain that the gas valves are closed, and that no gas is being lost when flying near pressure height.

The following check procedure of the valves is recommended: 1. Before take-of . f, crack all va lves 6pen for a short instant to ma ke ce~tain that the valves and telltale lights operate satisfactorily.

2. When flying close to pressure height, p ull closing control of gas valves fro m t ime to ti m e.

-41- R - Aft Air Valve, Close A - Safety Switch I, J, K, L- Fuel Dumping B- Mechanic's Signal M - Port Helium Valve, Close C - Forwar~ Air Damper N - . Port Helium Valve, Open D - Forward Air Valve, Open 0 - Stlbd Helium Valve, Close E - Aft Air Valve, Open P- St'bd.Helium Valve, Open F - Aft Air Damper, Close Q, R - Slip Tanks G - "Forward Air Valve, Close

~ (!)Q)®@ ®@

· Fig. XI - Flight and Instrument Panel -42- (b) Damper Control The air dampers can be kept open by means of an olive on the control cables. The dampers are normally held closed by springs which prevent the dampers from opening under the pressure of air from the scoops.

(c) Manometers The air pressure in the two ballonets and the gas pressure in the envelope are read on three manometers, located on the flight panel. Each manometer is equipped with a three-position valve ·.

When this valve is turned on the position marked "Check" the manometers should read zero. If necessary, the reading can be brought back to zero by means of an adjusting dial. This check should be made before every take-off.

v7hile in flight the valve should be turned on the position marked "static."

A mechanical manometer on the instrument panel reads the gas pressure and is used as a check .on tl).e liquid manometer.

-43- Fig. XII Starting Auxiliary Blower (K-.3 thru K-98) (d) Starting Auxiliary Blower (K-.3 thru K-98) 1. Turn on switch on pilot's instrument panel.

2. Open fuel line shut-off cock on gasoline filter bowl as-sembly. (Turn counter-clockwise) • .3. Close carburetor choke (choke is open when lever is against stop pin). Open throttle by pulling black button on throttle wire.

4. Wind starting rope on pulley, brace one hand on fuel tank and pull rope hard, giving quick spin to engine. Repeat, if necessary, until engine starts. Then immediately open choke partially easing to full position as engine warms up. If engine is warm from previous running, it is not necessary to use choke for starting.

5. Open air intake door.

-44- (e) Stonping Blower 1. Turn off button on pilot's p~nel.

NOTE: Engine can also be stopped by pressing red stop button, mounted on m e. gneto stator plate until engine stops.

2. Vfuen the airship is in flight with the Homelite Model HRU-28 auxiliary blower stopped, a parti al vacuum is set up in the exha ust. This partial vacuum draws fuel into the crankcase.

In many instances, this h a s resulted in bursting the crankcase or cylinders and pistons w hen the pl~nt was st a rted. To prevent this, the fuel line shut-off valve must be ti gh tly closed whenever the plant is stopped, whether in flight or at the airship base.

(f) LaDel Electric Blower The production schedule calls for a LaDel electric blower to replace the gasoline powered blower, described above, on airships K-99 and future. The only source of power for this blower is the Lawrance auxili a ry generator.

The auxili a ry generator must be running at rated speed before the electric blower may be used.

(5) Summary: Pressure Control System (a) Settings 1. Forwa rd Air Valve: Begins to open a t 1.50 inches of water of air pressure in the for wa rd ballonet as read on car manometer.

2. Aft Air Valve: Begins to open at 2.00 inches of water of air pressure in the aft ballonet a s read on car manometer.

3. Gas Valve: Begins to open at 2-1/2-inches of water as r ead on gas manometer.

(b) Control, Instruments & Auxiliaries Chart See Fig. XIII (c) Operation Chart See Fig. XIV -45- INST , RUMENTS, CONTROLS AUXILIARIES PURPOSE LOCATION Air Scoop Port & Starboard To control air pressure in Adjustment of Frame 6. air chambers and ballonets.

Air Damper Pilot's Instrument To direct air to the for- Contols Panel Fig. XI ward or aft ballonet Air Valve Pilot's Instrument To release air from the for- Controls Panel Fig. XI ward or aft ballonets and to close valve.

Manometers (3) Pilot's Flight To indicate pressure of the Panel Fig. XI gas in envelope and of the air in the two ballonets Pressure Gage Pilot's Instrument To check liquid gas pressure manometer Panel Fig. XI Auxiliary Cabin Deck, Frame To supply air pressure to Blower 5, Fig. XII ballonets when regular sys- tem becomes inadequate Switch for Pilot's Instrument To shut off motor.

Auxiliary Board Fig. XI /l~so switch on engine Blower Gas Valve Pilot's Instrument To release gas manually and Controls Panel Fig. XI to close valve.

Air Sleeve Ceiling Frame 6. To blow air into gas in emergency To deflate ship rapidly in Rip Cords Outside of Forward emergency and Aft Doors Fig. XIII Controls, Instruments and Auxiliaries Chart -46- NORMAL SETTING REWLARE:S CONDITION OPERATION Take:.:.orf Air in both Both dampers Keep up ship inflation ballonets closed if necessary by opening dampers and by occasion- al . blasts of propellers or by auxiliary blower Climbing Air being re- Both dampers Watch for excessive gas leased from closed pressure. Stay below Fwd.Ballonet climbing rate of 1200 ft.

per minute.

Flying Ballonets are Open both Maintain full operating near fully deflat- dampers and pressure tn air system.

pressure ed.Gas valves scoops. Do not operate air valves height operate auto- manually. Check closing matically to control of gas valves to release gas if make sure no gas is being pressure height lost. Watch the tell-tale is exceeded. lights.

Level Ship in trim. Open forward Consider air as regular Flight Air in both damper and re- ballast in determining ballonets. gula te scoops effect of shift on trim.

to produce de- sired p.ressure Normal Air being nor- Open forward Watch for too low pressure.

damper Descend- mally replaced Stay below descending rate ing in forward of 600 ft. per minute.

ballonet Landing Motors are Start blower See Page 44 for instructions throttled motor,open to start blower motor~ down. Pressure intake door, from regular open both system is dampers.

inadequate Shifting use dampers & Consider air as regular air valves ballast in determining Air .

as needed. effect of shift on trim.

Blowing Excessive Untie sleeve Blow only the minimum amount air into loss of gas which connects air necessary to maintain gas air to gas. pressure.

Fig. XIV Operation Chart - Pressure Control System -47 ' ' I I I I I ' ' ' ' I I I I I I ' I ' ,'

I I

I I .'

I

' ' ' I I I · ~ ~ ~

I ~

I z .

bO u •r-1 r:r..

~ ....,

I

~ -48- C. MAJOR CONTROLS Occasional adjustments are required in the tension of the control lines of the major controls to compensate for slight changes in the shape of the envelope with vari- ations of the pressure and of the loading. Tension varies particularly with the fullness of the aft ballonet, a large amount of air in this ballonet causing the cables to slacken.

An automatic tensioning device located in the aft portion of the car between frames 1 and 2 takes care of part of these variations. In addition, the tension can be adjusted from the pilot's compartment. The crank on the port side is for the elevator lines, and the one on the starboard side is for the rudder lines. The tension of the controls should be checked from time to time in flight. A check should always be made immedia tely after a heavy take-off, because of the added sagging of the en- velope caused by the dynamic lift.

CAUTION: It is particularly important that the pilot check the controls and adjust the tension of the lines as required before take-off and before landing otherwise he may find himself without enough control in an emergency.

Occasional adjustments may also have to be made in flight.

-J,q_

ff 5T#C/(

"""' -~_ , ., LATCH KNOB SAFETY LATCH LATCH MOORING LOCK I V\ I OPERATING SHANK Fig. XVI - Top of Landing Gear Stru~ \ I D. RETRACTABLE LANDING GEAR (1) To Drop Landing Gear (a) Open trap door giving access to landing gear mechanism (car floor at frame 7).

(be) See that mooring pin is up~ ( ) Place crank on top of operatin g shaft and crank until top of strut is against the stop.

(d) Make sure that the latch drops fully into place, and lock it in place by means of the safety device.

(e) Back off crank slightly to relieve pressure on worm gear. Gear should now be ready for landing.

(2) To Retract Landing Gear After Takeoff (a) Open access trap door and place crank on top of strut shank.

(b) Turn the shank until the guide fork on top of the strut and the landing wheel are in a direct aft position.

Unlock the safety device and raise the latch.

Place the crank on the operating shaft and turn until the strut is fully retracted.

(f) Raise the mooring pin.

(3) To Lock Landing Gear at 90° To Axis Of Ship For Operation On Mooring Mast (a) Turn strut in p osition by means of crank inserted in positioning shank.

(b) Push mooring lock in place.

E. HANDLING LINES Attake-off, the yaw lines are stowed in two compart- ments in the bow of the car from where they can be released by means of a control located at the l , eft of the elevator pilot. A drag rope can be relea . sed from a compartment in the stern of the car by means of a control located on the port side of frame 2.

-52-

PAfll .0I

Pow£12 PLANT

=======III- POWER · PLANT References: 1. Engine Manufacturer's Manual 2. BuAer Manual 14-101 to 14-506 A. ENGINES (1) General Characteristics (a) K-3 thru K-8 : R-975-28 Wright Aero.

Take-off rating: 450 H.P. at 2250 r.p.m. at sea level.

Normal rating: 420 H.P. at 2200 r.p.m. at sea level.

Gear Ratio: Direct Drive Fuel: Aviation grade, 91 octane, AN Spec. AN-F-26 Oil: W.A.C. Spec. No. 5815 (b) From K-9 on: R 1340 - AN Pratt & Whitney Wasp Normal Rating: 425 H.P. at 1775 r.p.m. at sea level Gear Ratio: 3:2 Fuel: AN Spec. No. AN-VV-0-446a (2) Starting The starters are of the hand electric inertia type.

In starting, proceed as follows: (a) In cold weather plug in oil tank electric heater until tank feels warm to the hand.

(b) Turn the engines over four or five revolutions by pull- ing the propeller through by hand.

-53- CARBON MONOXIDE INDICATOR REMOVED Bu A er Bulletin No. 89 Fig. XVIII Mechanic's Panel -54- (d) Set carburetor mixture to "rich."

(e) Turn on fuel supply.

(f) Open throttle to the position corresponding to 600 RPM.

(g) Turn primer pump handle in the direction of the engine which it is desired to start, (to the right for the starboard engine, to the left for the port engine), give from 2 to 5 strokes of the pump after the priming line has been filled, and reset handle to neutral posi- tion.

(h) Turn ignition switch to "Both On."

(i) Make certain that main battery switch is closed.

(j) Turn generator switch on.

(k) Maintain about 3 lbs./sq.in. fuel pressure with the wobble pump.

(1) Select motor to be st a rted by means of selector switch.

(m) Push st a rter switch to "on" position, wait about 30 seconds until the whine of the st a rter indicates that it is running full speed and pull switch to "mesh."

(n) Repeat, if necessary, until engine st a rts.

CAUTION: If oil pressure does not come up to normal in 30 seconds, stop engines and . investigate.

-55- (3) Warming Up (a) Set carburetor heat control to full hot.

(b) Set the throttle for a. speed of about 600 RPM.

CAUTION: Do not attempt to operate engines over 1000 RPM until the oil~in tern erature has exceeded lOOOF. soc and do not exceed 1400 RPM for continued opera . tion on the ground under any condition.

Do not idle engines at speeds causing bad vibrations. Critical vibrations occur between 750 to 900 RPM.

Ground Test (4) operating Check RPM when on one or two magnetos. The drop in RPM when shifting from both magnetos to either of them should and not exceed 100 RPM, 40 RPM when shifting from one magne~p to the other. Check oil pres , sure, oil temperature, fuel pressure and battery charging rate.

(5) Take Off (a) Use both service tanks.

(b) Ope~ valve in cross connecting fuel line between the two engine fuel pumps.

(d) Cylinder head temperature should preferably not exceed 260° c. at the time of take off.

(e) Set mixture control to ttrich."

(f) Ret~rn preneat valve to full cold as throttles are opened.

-56- (g) Open throttle gradually (3 to 5 seconds desirable) being careful not to exceed limiting manifold pressure.

(6) Cruising (Reference Buaer Manual 14-206) (a) Do not exceed operating limits.

(b) Wait until motors have cooled down before lean- ing carburetor.

CAUTION: It must be kept in mind that while a lean mixture increases fuel economy, it also increases heating of . the engine. Leaning is only permissible at reduced power output.

See Engine Operator's Handbook for full discussion of the matter of carburetor setting.

(7) Single Engine Operation Whenever it is found necessary to operate on only one engine, stop other engine as directed below and leave mix- ture control on "Idle Cut-Off" position with closed throttle.

This setting insures that the wind-milling of the engine will draw minimum of fuel into the cylinder.

(8) Stopping (a) Vove mixture control to "Idle Cut-Off" position.

(b) ~~en the engines have stopped, turn all ignition switches to "Offn position.

-57- CAUTION: (9) Operating Limits and Charts (a) Operating Limits for Wright Engine (K-3 thru K-8 A1rships)."See page 59.

(b) Operating Limits for Pratt-~hitney Engines (K-9 and Subsequent Airships). See page 60 (c) Power Output of Wright Engine at Sea Leveland 1500 Ft. Altitude. See pages 61 and 62 (d) Power Output of Pratt-V>lhitney Engines at Sea Level and 1500 ft. Altitude. See pages 63 & 64 (e) Fuel Consumption of Wright Engine.

See page 65 (f) Fuel Consumption of Pratt-Whitney Engines.

See page 66 (g) Most Economical Air Speed. See page 67.

(h) Mechanic's Check Chart for Pr a tt-Whitney Engines. See page 68.

-58- OPERATING LIMITS FOR WRIGHT VlliiRLWIND R-975-28 K~3 to K-8 Airships Minimum Oil Inlet Temperature for Take-Off .•.•.•••••••••••• 104°F. or 40°C.

Desired Oil Temperature •••••••• 140°F. or 6o c.

Maximum Inlet Temperature •••••• or 190°F. 88°C.

Maximum Cylinder Temperature for Take-Off ••••••••••••••••• 500°F. or 260°C.

Maximum Cylinder Temperature (Cruising) ••••••••••••••••••• 450°F. or 230°C.

Desired Cylinder Temperature ••• 325°F. or 163°C.

Minimum . Oil Pressure (Idling) .................... . 10 lbs./sq.in.

Minimum Oil Pressure (Cruising) ••••••••••••••••••• 50 lbs./sq.in.

Desired Oil Pressure •••••••.• ~.

60-~0 lbs./sq.in.

F'uel Press11re ....... .......... . 2.5-3.5 lbs./sq.in.

-5 9- OPERATING LIMITS FOR PR A TT & WHITNEY R-1340 WA SP ENGINE For K-9 and Future Minimum Inlet Temperature Oil for ............................... c.

·' Take-off 40° :.l'l Desired Oil Inlet Temperature 60° c. c . . ;'. .............

- 75° Maximum Oil Inlet Temperature ............. 850 c.

. ~ .. ~ r.., ~ Maximum Cylinder Temperature -1 to 1-1/2 Min.Climb ••••••••••••••••••••• Head 260° C.

Base 1680 c.

Maximum Cylinder Temperature ·-· -Continuous Cruising • • . • • • • • • • • • • • • • • • • • • • Head 2320 C.

Base 93° C. 121° C.

Minimum Oil Pressure

(At idling speeds) . .. . . . . . . ... . ..... .. .. . . 10 lbs./sq.in •

..., ~ Minimum at 1000 R.P.M. ................... . 40 lbs./sq.in •

I • . .................. .

50 lbs./sq.in. -'i Minimum at 1400 - R.P .M.

Desired Oil Pressure at and above i 1400 R.P.M. ·····~··••••••••••••••••••••••• 70-90 lbs./sq.in.

. For Setting: ~~ 1400 R.P.M., 65°C. Oil-in, using 1100 Oil •• 80 lbs./sq.in.

Minimum Fuel Pressure (400 RPM or less) •••• 2 lbs./sq.in.

Minimum Fuel Pressure ··· (1000 RPM or above) •••••••••••••••••••••••• 4 lbs./sq.in.

Desired Fuel Pressure / ": :'. (1000 RPM ' or above) •••••••••••••••••••••••• 5 lbs.sq.in.

Maximum Fuel Pressure (1000 RPM or above) •••••••••••••••••••••••• 6 lbs./sq.in.

Desired Carburetor Air Intake Temperature.

I ~7 - J Note: Take-off - Return controls to "Full Cold" as throttles are opened.

Idling . .. . . ........ . .. . . . . .. . .. . . . .. ..

50° c.

__ , Cruising: 1400 RPM or less • • • • • • • • • • • • • 500 c.

Above 1400 RPM with stabilized operating conditions •••••••• 380 C.

-60- R.P.M.

FULL THROTTLE HORSE POWER i500 ft. ALTITUDE PERFORMANCE HORSE . POWER VS. MANIFOLD PRESSURE WRIGHT AERO ENGINE MODEL R-975-28 Fig. XX 36 38 30 32 31 20 22 24 26 28 ABSOLUTE MANIFOLD PHESS1J 'flE IN . HG -62- •··-J --~-----;-·--..,.---~ -------~-------·----;-·~-------- ----- -- --------P··------------- ' ' I .. __ ~---.-----......,.._~-----. -----:-----...--------. -------·----- -----· '1'·-- I -------------+----- ------ ' .

• I ------· -·-· --- POVIER -- CURVES +p OW -PHATT -:- AND -- V/HITHEY - -· -

-- .... - ~ -

ENGINE MODEL H.R. -1340-AU-2 _ _______ , __ - ___ _; __ -+·--------L-----~---__.__---~ _______ ,_ ______ .. _____ : __ _.:.

. ' ' ; AT SEA - LEVEL

..., ______ ---~ .. _ _

. .

--------~------~-~-~-----~ Frcr : xxi 600 ~ . . . . . .

:------------------+--- ... --------------- .... --------- ------+··----------+-- -~---~--· . , !

__ _......... ____ __...._,

.. ______ _:~-------- .. . .. --~--~----; _____ ,.:. _ - ---

. .

' ' ! ; I pOO r - - I t ---. -- .. --~----i _ .. _______ - -------- ---------------- ·-+----·' i !

- i - ·--· l . 1 FULL THROTTLE ' . l ' ·-----·---------- --- - --r-··--t-~-t---- -, -·:-~· HORSE-PO.\'IER ---·-t· 1 I 40C . I 1' I ' ' ' I ..... ____________ _. ____ .,.._~-~~---- ---------- ..

--- ---- ---------------~j~~-:.J - ~

-300 ' - ---·----1- ____ ... __ _ I R.P.M. , ~200 - • 8100 l ~O Q _~ 18 0 D 1700 " 160 0 /': 1500 100 -------------- ----------~--~4~-:~6~- . :30.~ - ~40 20 22 ~A 26 28 30 62 3 0 ~ ABSOLUTE MA NI FO LD P RESS U RE, IN. HG • ..

-6 3- POWER CURVES FOR PRATT AND WHITN"E.'Y ENGINE MODEL IIR-1340-AN-2 .

AT 1500 FT . ALTITUDE Fig. XXII R. P.M .

, 1900 FULL THROTTLE 500 HORSE-POWER 1' 100 tJj :;:j 300 ;t> @ ~ ::u (/.)

t::l '1:J 200 ~ ::u 38 40 28 30 32 34 36 20 22 24 ABSOLU'l'E MANIFOLD PRESSURE, IN. HG.

-64- -, 2~00 FUEL CON SU MPT · ION · · AND R . P . M. VS . AIR SPEED 2000 ' FOR K-3 THRO K~S SHIPS 80 EQUIPPED WITH WRIGHT R975-28 ENGINES .

~"'0s .n'l>. \) ~'' ~ . ~e> Fig. XXIII -- -·1 800 o::; ;::::> §§ .......__,_ (fJ ro H ~~ o::; 1 600 I :::;> :z; ·:{~~ ,-vv I .

"' ~~() .

~ H ~~ I

"'

3oo 1----:.. _so_ - _______________ _ E-t ' P-o P-o .

~ (;() ~1- ;::::> 0:: :z; ~ }: (!)

I p ~Q~ z ...:1 ~ · -a ~" H ~ · - ~ ~"\ ~ 40 ~ · H < P~<o f:il ......._ o-' "'"' 30 PART LEAN 120 0 100 ' 1000 •10 50 60 AIR 0 PEED - KNOTS ~ r

-- -~ -- r- -- . --- i - -- - r-- I .. -

I -I - '- M l-

i

Fuel Average Fuel Consumption and R.P.M.

I - ! . · ['· -· ... '---. p: .. ; __

Consumption - VS - Air Speed (K-57 & Future) .

I . - . • . •-- -

I

-· ]. .. ..... . .. . __ L .. i--·-: -·

Equipped with Pratt and ~hitney r ! j' ! I I ·-·' j 2000 R- 1340 - AN - 2 Engines i !___ . _ _ _j ___ 1, .... 1 ...

f· go I ' I 12-1/2 Ft.Prope11ers - set at 190 I --~ 1900 I ! , ' I I I

- -r -·-r -· - ··· ·• .. -- :-·· t -·-

NA - Y9E1 - 510 Stromberg Carbur . etors

. · ! . ~ - t. 1 1goo

I ' • I I l 701 l I .

- ~

.. I' : ....... 1 ..... --·~·--· ~-+-·-1

4ool Fig~XXIV I f - ... -! -- --- . 1700 J4 I I I l ; I ~ ' I . I . I

1·· · 1 - · · · ! · ---r · ;··· 1 .. · ·

6ol~ .J I-. ···t· 1 1600 J4

I . i ! I I

C) I

J4 I 1. I ! I Po

I ~ . r ·--1 - - · ··; · i ·· ., ... ·--

t :}f l- . -- i : 1500

" ::rl 300 · 50 c:: " J4 ,.-i ~ i . ! . "f ··-! ---1--+·- !-----1-~- ...

. ...

£'e as • .1. :. ' 1400 .

I ' I I I I ' l I I Ul .. + ·- i. l--- . ~.. -· --1 . --·-+ ....

.0 . • i I ' I 4o ..3 i : i I ! I 1300

. , . . I

I ! I I I

J ... L ..... : .... -. --- t ... I __ L 1

I I I I 1 1~00

I

I I I I I f I .. , .... 1 ..... , ........... · ·-·· .... .

I i I I I !

. ! I. l I 1100

I I I I

1----L.. ..J. '··-· I 1 1 i i I i ldoo.

I : i I I I

6o 4o 50 45 55 I - ~5 ·{· ·r· . --: -7 f .... : .......

I I_ • _, l I . i I I .

TRUE AIR SPIED - KNOTS l -- --+---+--·- -r·-~----T·· -,

I l i i l I

L __ L_.t ___ l _ l. J

L HEAD WIND VELOCITY, MOST ECONOliTCAL AIR SPEED, KNOTS KNOTS thru K-8 K-3 K-9 and Future 10 46.0 42.0 46.0 15 42.0 42.0 20 46.0 25 46.0 43.5 49.0 50.0 51.5 56.5 40 56.0 62.·5 64.0 45 58.0 64.0 58.0 Fig. XXV Economical Air Speeds -67- B. FUEL SYSTEM The fuel system of the K-airsh1p is designed to make · possible the shifting of fuel for the purpose of trimming the ship without interference with the normal fe ed of the engine. This is accomplished by carrying the bulk of the fuel in two banks of storage tanks, a forward and an aft bank, and by feeding the engines from two service tanks which can be isolated from the rest of the system. The service tanks can be filled from either bank of storage tanks without interruption to the feed of the engines.

The system can be filled through an outside connection or through an inside connection by means of the transfer pump.

Provisions are made for dumping fuel from aft storage tanks and for the release of two slip tanks located under the floor of the cabin, for the transfer of fuel from the slip tanks to the rest of the system and for the proper filtering of the fuel.

CAUTION: 1. !t take-off, always open valve in cross-connect- ing fuel line to insure against a fuel pump failure.

2. Make certain that there is ample fuel in the service tanks at all times during flight.

3. Do not dump fuel wh - en either of the auxiliary engines is running.

-69- .

Oil Operating Engine Mixture Carburetor Oil Inlet Cyl. Head Pressure REMARKS Condition Control Air Temp. lbs./in2 R.P.M. Temp. Temp.

Start Set FULL fULL Must Show In cold weather heat oil in out- Throttle RICH COLD in 30 Sec. rigger tanks by means of elect- for 600 rical units.

R.P.M.

Warm Up 500-600 FULL FULL For 1 Min. RICH HOT Do not exceed 1400 r.~.m. for 1000 After Minimum continual operation.

(2) Ground 1400 FULL 32°C. 37.8°C. 204°C. Drop in R.P.M. when shifting 70-90 Test RICH Minimum from one magneto to the other should not exceed 40.

I 0' Max. rating 600 H.P. at 2250 Take-orr 1800 FULL 32°C. 60-64°C. 233°C. 70-90 ()) R.P.M.

I Max. RICH Do not lean carburetor beyond Cruising 1300 PART 32°C. 6o-64°c. 204°C. 70-90 10 R.P.M. drop of speed.

Desired LEAN or Less Desired " Idle engine until ~ylinder Stopping 400-500 FULL tem~erature has dropped below LEAN 220 C. before atopping.

. 0 1. With propeller setting of 23 at 42" radius do not fly •hip faster than 67 knots.

2. Do not operate engines at speeds causing bad vibrations. Maximum vibrations occur between 650 to 900 r.p.m.

Fig.XXVI Mechanic's Check Chart Pratt and Whitney Rl340 - AN2 Wasp Engine

4· Clean the four fuel strainers after every

120 hours flying time, and oftener, if necessary. The strainers should be cleaned immediately when irregular operation of either engine develops.

For the location of the strainers and instructions . for cleaning them in flight, see Fig. XXVII on the following page.

5. Make certain that pressure in fuel system does not exceed 25 lbs. per sq.in. when filling from external pump.

6. Do not feed engines from a tank containing less than 12 gallons of fuel as the outlet is nearly uncovered with this amount of fuel still in the tapk, and with the ship at a 30° angle of pitch.

The various operations which can be performed with the system, together with the proper settings of the valves, are described in Figures XXVIII-a thru XXVIII-j for K-3 thru K-10 airships, and in Figures XXIX-a thru XXIX-j for K-11 and future.

C. RECOMMENDED CARBURETOR ADJUSTMENT a Run engine at 400 RPM.

b Cylinder head temperature should be normal.

c Have good plugs in engine.

d Have mixture control FULL RICH.

e Note RPM.

f Rapidly move mixture control from FULL RICH to IDLE CUT OFF positfon. Catch the engine before it stalls.

(g) Note RPM.

1. If large gain in RPM - Carburetor is set too rich.

2. If loss in RPM - Carburetor is set too lean.

3. Desired - gain of from 0 to 10 RPM.

The desired setting is the RICH BEST POWER setting for the carburetor at the idle speed of the engine.

-70-

Next: LexTest_2014_08_18_07_33_54_133 →

LexTest_2014_08_18_07_33_54_133

Fig. XXVII 3-4-5 -6 - 0NLY - TANK.5-I-2.-3 - 4 - 7 -8·9~1 0 - ARF FUEL SYSTEM STORAGE TANK.5-IZS6AL . EACH-

·· ;; ----- -------=x---

/ ' AND fUTURE ONLY I -- I \ ' ' ~--~ I ' "" - -. ' I c ~ \ I ' I I I I I .1 I I I I I I I \

- /

; -;tJ.. I / -- :-l. _, ;,•· . (__- -- _- ;_-/ -,- ~.,? ~ ~I / I -.: .....

IN TRANSFER PUMP CARBURETOR-POWER PLANT -- - FILLER HOSE ~ -- -

)\

BARRETT COUPLING · LIN£ STI<A!NER

\

'ER- TO INTAKE 11ANifOLD SLIP TANK- 100 6AL. , -::::oo.,_..........,.: SLIP TANK- 80 GAL-c-. ----------,------~-.......~ REMOVE AND CLEAN FUEL STRAINERS WITH GASOLINE AND A BRUSH IN THE FOLLOWING SEQUENCE (1) Open crossover valve. (2) Close valve _on fuel supply . line to one engine.

(3) Drain fuel from inoperative emergency pump. (4) Remove and clean strainer

from inoperative pump. (5) Replace strainer. (6) Reopen valve previously EMERIJENCV PUMP STRAINER_.

closed on ~ngine supply line. (7) Repeat for other engine. (8) Close . crossover valve. (9) Cl . ose valves to main transfer Fump. (10) Remove and clean strainer immediat~y above ma:i,n transfer pump. (llJ Replace strainer. (12) CJ.os~ , va~ves on fuel line to Barrett coupling • .. (13) Remove and clean strainer above ceiling of car in filler line. (14) Replace strainer. (15) Adjust fuel valves for normal operation.

-71-

Next: LexTest_2014_08_18_07_34_44_003 →

LexTest_2014_08_18_07_34_44_003

FILLING . SYSTEM FROM OUTSIDE CONNECTION Fill each tank in • succession according to desired fuel load and. fuel distrJ.bution.

Truck pump should be equipped with relief valve. Set for a max.

of 25 lbs. per sq. in.

If no relief valve is available throttle down ~~=-~ the flow by means of main valve.

K-.3 thru K-10 Fig. X X VIII-a FILLING SYSTEM THROUGH INSIDE CONNECTION Use tr a nsfer pump and Filler Hose K-.3 thru K-10 Fig. XXVIII-b -72- lsr'e'o c~Re .

TAKE-OFF Feed engines from both service tanks. Open cross feeding valve.

FU[C SY$T[M K 1K04Do!ATo : e-..

K-3 thru K-10 Fig. XXVIII-c FUEL PUMP FAILURES [l;RANSF'ER PU"P !' TH RE:W YALY£ ~ ~~~~~15~/TION ""'

"

In case of failure of

"' ·

one engine driven pump open cross connecting valve. In case of failure of both pumps set as indicated in · diagrPm and us .e emergency pump.

K-3 thru K-10 Fig.XXVIII-d -73- FILLING AFT SERVICE TANK FROM AFT STORAGE TANKS WHILE FEEDING ENGINES FROM FORWARD SERVICE TANKS [I'" 12: BARRETT rii..L IN Ci CONNECTION I (S!RAlNERS I Ose transfer pump. Open outlet valve of storage tank . from which it is desired to draw fuel.

ENCY ~ ~------~A~sm~ rUEl SY~T£ 10 II ~T o: o-...

K- 3 thru K-10 Fig. XXVIII-e ' FILLING AFT SERVICE TANK FROM FO . RWARD STORAGE TANKS WHILE. FEED- [I'" .

ING ENGINES FROM FORWARD SERVICE . ·• 12:~ ro..LING TANK. ~~~ C ON NECTION [rRANSrER PUWP friiTH R£Lit YALY£ "" [Si'RA lNERS I f'RE~E ST..Qf_ '- lrOR~HrS fibSITION '-

"

'\ Use tr~ nsfer pum p * Open outlet val v~ of sto rag e tank from which it - 1.s desired to draw fuel t o £ill service tank.

K-3 thru K-10 Fig .. XXVlti-f -74- FILLING FORYiARD SERVICE TANK FROM AFT STORAGE TANKS ~EILE FEEDING ENGINES FROM AFT SERVICE TANK Use transfer pump. Open outlet valve of storage tank from which it is desired to draw fuel to fill service tank.

iD4PGENCY Nil' ~------~A~~m~ K-3 thru K-10 Fig. XXVIII-g FILLING FORWARD SERVICE TANK FROM FORWARD S'TORAGE TANKS WHILE FEEO- ING ENGINES FROM AFT SERVICE TANKS (S!RA l NERS I Use transfer pump. Open outlet valve of storage tank from which it is desired t~ d~aw fuel to fill service tank.

K-3 thru K-10 Fig.XXVIII-h -75- EMERGENCY PUMP FILLING SYST~~ FROM & STRAINER UN I T.

OUTSIDE STRAINER DRAIN .

. CONNECTION I" STRAI~ - ' If BAitRETT ' ' FILLING CONNECTION .

TRANSFER PUMP ~

Fill each tank WITH RELIEF VALVE.

in success ion a c- n ~---'1~-..---'1---i:r----<

cording to de- .

sired fuel load .

and fuel distrib- ution. Truck pump should be equipped with re- lief valve. Set for a max. of 25 lbs. per sq. in.

If no relief is available - throt- tle dovm the flOW by means of ENGINE DRIVEN PUMP •WITH BY-PASS DRAIN.

main ValVe. f!_&~Ri!El~IE£...F _jV~A~lV!'!E_iS . ____ -;~3 EMERGENCY PUMP 6 STRAINER UN!.L POU CARB . - - ',, SCHEMATIC DIAGRAM-FUEL SYSTEM-"~"AIRSHIP K-11 AND FUTURE Fig. XXIX-a EMERGENCY PUMP FILLING SYSTEM ~reb ..

& STRAINER UNIT.

THROUGH INSIDE STRAINER DRAIN .

I" S J!f.!~JL ... _ CONNECTION If BARRETT FILLING CONNEC TION Use transfer pump and filler f'llL(llt ....... ~,"T'J'-- ........ ~~ ... l hose.

ENGINE DR I VEN PUMP WITH BY-PASS & RELIEF VALVES .

\ STRAINER DRAIN .

EMERGENCY PUMP . & STRAINER UNIL PORT CARB .

K-11 AND FUTURE SCHEMATIC DIAGRAM-FUEL SYSTEf'f~'AIRSHIP Fig. XXIX-b -77- TRANSFERRING FUEL FROM F0RWARD TO AFT STORAGE- TANKS WHILE FEEDING ENGINES FROM SERVICE TANKS Open outlet valves of tank from which it is desired _ to transfer fuel. Use transfer pump.

~-l!:>POR"'-'l · _ C_ AR o .

K-3 thru K-10 Fig. XXVIII-i TRANSFERRING FUEL FROM AFT TO FORWARD STORAGE TANKS WHILE r7 FEEDING ENGINES FROM SERVICE TANKS " lj!BARRETT _ ri!,LING CONNECTION [;RANSrER PUOIP _! ITH R£ . LIT yALV£ ""' fSTRA:NERS I ~ ~~WOt~IS ~ITION "'

""

Open outlet va~ves of

- "' ·

tanks from which it is desired to transfer fuel. Use trans£er pump.

rurc ~·:.nw • $04EMAT •: .: ~.AGAA..., K-3 thru K-10 F:tg. XXVIII-j -76- TRANSFERRING FUEL FROM FORWARD TO AFT STORAGE TANKS WHILE FEEDING ENGINES FROM SERVICE TANKS ~ TRANSrER PU .. P ~! TH RE:L£T Y&-Yt ""' I fSTR A:NE RS I ~~ ~~\2fUT~ ITIO N "-..

"

"'

Open outlet valves of tank from which it is desired _ to transfer fuel. Use transfer pump.

K-3 thru K-10 Fig. XXVIII-i TRANSFERRING FUEL FROM AF'I' TO FORWARD STORAGE TANKS WHILE FEEDING ENGINES FROM SERVICE TANKS Open outlet va~ves of tanks from which it is desired to transfer fuel. Use trans£er pump.

K-3 thru K-10 F'rg. XXVIII-j -76- EMERGENCY PUMP & STRAINER UN IT TAKE-OFF ST"-AINER DRAIN .

I' tf BARRETT FilLING CONNECTION .

TRANSFER PUMP WITH RELIEF VALVE.

Feed engines from both service tanks Open cross feeding valve.

ENGINE DRIVEN PUMP WITH BY-PASS DRAIN .

& RELIEF VALVES .

EMERGENCY PUMP . 6 STRAINER UNIT POlT CARB . -- , S(HEMAT!C DIAGRAM-Fl,!L SYSTEM - ·~·AIRSHIP K-11 AND FUTURE Fig. XXIX-c EMERGE'KY PUMP FUEL PU M P FAILURES 6 STRAINER UN IT STI\AINER DRAIN .

tf BARRETT FILLING CONNECTION .

TRANSFER · PUMP WITH RELIEF VALVE In case of failure of one engine driven pump open cross connecting valve. In case of fniT t_,..., failure of both \: 1 !

'L-.+--.1 pumps set as indi- ~ c a ted in diagram ~-----+-- ......... _" _ •• _._ ... _. ~H<J~~ ~D..--+---+----1 and use either ~ emergency pum p. ~ r -- ~--. ~ i : ,u:~ 'j --~o-· 8 6 ENG INE DRIVEN PUMP WITH BY-PASS & RELIEF VALVES . \ STRAINER DRAIN .

EMERGENCY PUMP 6 SHAINER UNll_ PORT CMB .

--- -'

SCHEMf- Tk: DIAGRAttF!JL SYSTEM : ·~-AIRSHIP K-11 AND FUTURE Fig. XXI X-d -78- EMERGENCY PUMP 6 STRAINER UNil_ STRAINER DRAIN .

TANK FROM tf BARRETT FORWARD STORAGE FILLING CONNECTION .

TRANSFER PUMP TANKS WHILE WITH RELIEF VALVE .

FEEDING .ENGINES FROM FORWARD SERVICE TANK ENGINE DRIVEN PUMP WITH BY~PASS & RELIEF VALVES .

\ STRAINER DRAIN .

EMERGENCY PUMP 6 STRAINER UNLL POll CARB .

--- ,,_ K-11 . AND FUTURE SCHEMATIC DIAGRAM-FUEL SYSTEM:"'AIRSHIP Fig. XXIX-€ EMERGENCY PUMP FILLING AFT SERVICE 6 STRAINER UNIT.

TANK FROM AFT STRAINER DRAIN .

tf BARRETT STORAGE TANKS FILLING . CONNKTI ON.

TRANSFER PUMP Vv'HILE FEEDING . WITH RELIEF VALVE.

ENGINES FROM FORWARD SERVICE TANKS Use transfer pump Open outlet valve of storage tank from which it is desired to draw fuel to fill ser- vice tank.

ENGINE DRIVEN PUMP WITH BY-PASS \ STRA I NER DRAIN .

& RELIEF VALVES .

EMERGENCY PUMP 6 STRAINER UNIT PORT CARB . - ~ ', SCHEMATIC DIAGRAM-FlJL SYSTEM ~ YAIRSHIP K-11 AND FUTURE Fig. XXIX-f -79- EMERGENCY PUMP 6 STRAINER UNIT FILLING FORWARD STRAINER DRAIN.

SERVICE TANK tf BARRETT FILLING CONNECTION .

F.ROM AFT STORAGE TRANSFER PUMP TANKS WHILE WITH RELIEF VALVE.

FEEDING ENGINES FROM AFT SERVICE TA.NK ENGINE DRIVEN PUMP WITH BY- PASS & RELIEF VALVES . \ STRAINER DRAIN .

EMERGENCY PUMP 6 STRAINER UN!l_ POlT CARB .

SCHEMATIC DI .... GR .... ttFllL SYS!EM-~"AIRSHIP K-11 AND FUTURE Fig. XXIX-g EMERGENCY PUMP 6 STRAINER UNIT .

FILLING FORWARD STRAINER DRAIN.

SERVICE TANK tf BARRETT FROM FORWARD FILLING CONNECTION STORAGE TANKS WHILE FEEDING ENGINES FROM AFT SERVICE TANKS Use transfer pump.

Open outlet valve of storage tank from which it is desired to draw fuel, to fill ser- vice tank.

ENGINE DRIVEN PUMP WITH BY-PASS 6 RELIEF VALVES .

\ STRAINER DRAIN .

EMERGENCY PUMP 6 STRAINER UNIT POlT CARB SCHEMATIC DI .... GRAttFlll SYSTEM_.~-AIRSHIP K-11 AND FUTURR Fig. XXIX-h -80- EMERGENCY PUMP TRANSFERRING FUEL 6 STRAINER UNIT.

STRAINER DRAIN .

FROM FORWARD TO I' STRAINER.

AFT STORAGE TANKS-'-"'-'-"''"'---____, tf BARRETT FILLING CONNECTION .

WHILE FEEDING TRANSFER PUMP ENGINES FROM FOR- WITH RELIEF VALVE.

WARD SERVICE TANK Open outlet valves of tanks from which it is de- sire~ to transfer fuel. Use trans- fer pump.

ENGINE DRIVEN PUMP WITH BY-PASS & RELIEF VALVES .

\ STRAINER DRAIN.

EMERGENCY PUMP 6 STRAINER UNIT POU CARS .

.... ___ ...

K-11 AND FUTURE scHEMATk:::: DIAGRArtfl.IL SYSTEM-)<-AIRSHIP Fig. XXIX-i EMERGENCY PUMP 6 STRAINER UNIT.

TRt\NSFERRING FUEL ~\ STRAINER DRAIN .

FROM AFT TO FOR- r STRAINER . i ) tf BAUETT WARD STORAGE TANKS \ / FILLING CONNECTION .

WHILE FEEDING ~~~~s~~~~E~uv~~vE ',, ..... -_ ' ®J::)-1(.!!>+ ENGINE FROM AFT SERVICE TANK Open outlet valves r,--<t--, of . tanks from ::""t i which it is de- "---+--:

sired to transfer <f'-

fuel • use trans- r-----t--""-----~;pH<C!)H{;!;}til@+<...__+---+-- ....

fer pump. <$-- ;-r--""\ ~ : ,u,t. •J ~-,o--· ENGINE DRIVEN PUMP WITH BY- PASS & RELIEF VALVES .

\ STRAINER DRAIN .

EMERGENCY PUMP 6 STRAINER UN[l_ PORT CARS .

K-11 AND FUTURE SCHEMATIC DIAGRAM-FUEL SYSTEM-~ ' / Fig. XXIX-j -81 D. OIL SYSTEM The oil system for K-3 thru K-74 includes a 30-gallon oil storage tank below the deck of the car, and two 14-gallon oil service tanks, one in each engine na~elle, and a transfer pump with necessary fittings.

In K-75 and future, the oil storage tank, transfer pump and fittings are removed and the oil service tanks in the nacelles are enlarged to the 26-gallon ' size.

The oil is cooled by a radiator which is located in the nacelle for the K-3 thru K-8 airships, and which is suspended from the lower outriggers for the K-9 and sub- sequent ships.

The service tanks are equipped with electrical heating units to heat the oil in cold weather.

The amount of oil in the service tanks is read on two oil gages located on the mechanic's panel. The amount of oil in the storage tanks is read directly on the tank through a trap door in the deck of the car.

-82-

/

\

THREE WAY VALVE \ ~ / PRE SS URE \ )- ~ -- TO PO _ 'AUG£ LINE

, -J £NG!N£

//

/ PRESSURE GAUGES ,----<, _~ / _._ ~\

/

( L TO EN~IN£ VENT !NUT

I ~'- I I f • c:::., ....

fi ~-'-' \ .. ~ \ ""'- '- -::----------

' . . • ' ""- ""'

-~ >---- DETAIL~ ~_)---~:---.1__ _ ___)

I tRCX ·1 iNGINE OIL PUMP -- ~ \>.)

~

.~ ~ ;4 ,' ' ~ OI L STRAINER " 10 MESH- . 025 MONEL WIR.C TEM PERA; ·uR£ RE6ULATVR Fig. XXX OIL SYSTEM DETAIL :4" (K-3 thru K-74) ' /

\ _/

'\ )- PR~SSURE L LINE

' '---- - , / ' ENGINE

/

/ , ~' _ r- OILTANK

( -- -............._ ~- ro"~''"'

PRESSURE GAUGE LIN£ STARBOARD ENGINE

\

~ ~ ~

;-- I \"'--- ~- C»

~2_)

''-< ~

t

OIL OUTLET FROiiEiiGT!it -- OI L IN LET TO ENG IN E SCREEN ~ ~~

----------

(*10 11[SH -Oi! 5 WIR£ }~ :::: ~ - < wJ - OIL COOLER

-- FR O M TEMP. REGULA TOR ---------

~ ~r · - - TEMPERATURE REGULATOR

i!}) ~ \

//Ill , I )"' Fig. XXXI ' # SC REEN FLANGE OIL SYSTEM DETAIL ~r (K-75 and Future) SUMMARY OF OPERATION OF OIL SYSTEI >1 RE!IfARKS OPERATIONS .

Filling system with oil. Fill storage tank through (K-3 thru K-74) connection inside car and fill service tanks by means of transfer pump.

Filling service tank from Use transfer pump.

storage tank.

(K-3 thru K-74) Cleaning oil filter. Turn knob on top of filter one (K-3 thru K-8) full revolution every ten (10) hours operation.

Regulating cooling. Adjust opening of scoops by means (K-3 thru K-8) of control on mechanic's stand.

Heating oil before Plug in electrical heating unit.

starting engines.

(All ships) Filling system with oil. Fill each 26-gallon service tank (K-75 and Future) thru filler neck which extends thru inboard for 'N?.. rd nacelle at end of c a twall{.

Remove and clean oil filters at Cleaning oil filter.

each major overhaul, interim (K-9 and Future) overhaul, or oftener if conditions are unfavorable. See Oil System diagram for location of filters.

-85-

PA'RT JY

fi£eT121fJAL .$YST£M

Next: LexTest_2014_08_18_07_35_48_991 →

LexTest_2014_08_18_07_35_48_991

UOMIWG ADAPT .EA. RitA 'I e

"''~o~£J:~~~~~:i~:~.ro"e STARBOARD SIDE

t;I)W TVItltET AS5Y . (6079- 532$)

r SIDE

MBAAR; ~:,.C~I~~~~~TOoct's REC:~IY~ . tt @

AT 'tt/~~z~M~;r-tE/B> .

ARB :,j 2.- RA.D/0 O'EftATo . 'l 5 /l.£CFIVER.@ GP·1 · TRANSM ITT E!i'f!!!j INTUI'HONE SYSTEM (6079 -6109) AIR f)JSCHAIIGF CON J>I VT ~ETWE EM ~R . 6 I ? (4oS0-7.,2,) GUNNElS lADDER (4079-2819)

FV£-t. S"t".5rT' #""f ('10'79 -.:z-4 60)

PRESSIJR« TUBE SYSTt'M(60)'9- 5682.)

CONTR.OL. .ASSY· (6079-.35.!8) PilOTS JNSTRtJMtiiT PANEL ( '079 ~ 3702} ,_L I GH'T INSTR.U Mt'NT PAN~L (6079·29.,9) llUDD~R PIJ..Od PJ.NEJ.. ( 6079-S?"'7) ELE-CTRICA,L INSTALiATION ('<J79-5S"2"'#) INCLINOMETER INSTAL. (.,._079 -S 09/) MAJO~ CONT~OJ. S AS.I"Y . (,0"19 -ISO!)

CONTROLS ( 6079 -41-ZE"f.)

I'YHl£~0;;:KE- R(~~~~~ st6§)@1iSM (607 9-3'f.61)

MAHO RECEIVER -A RI!!J 19 .

~R£CLI~ING CHAIR *t50 ( <f079 -39/~ S.!.AT TI(.T (~AIR - c:_/il. ·S I}

--HANDL I NG ROPE BO.i A:55Y. ·( 079-J871} MR.TJr t ON AT Flf . 9( 9-7!1} '--HAVIGATOR ~ S LIGHT (2 .0 9 -2.70I) NA!fi . G).TIONAL. 6EAR RACK ( 30?9-405'2) O~'s TABLE ($079 -423+) UNIT RANGE " A:·.-r. -F .. FOR CP?

ALLATI0/11 (6079· S52 -"') · f91?AD IO I NSTALLATION (6079·6118)

RACK INS TALLAoO,:?_,-;/?;m

LIGHT ( NA.~ . - · 1021) @RADIO TABLE AS5Y: (6079 · 413!J) H.t.TCH {)()()R. 0~/flf{TING MECHAN I SM (6079·2736) .,.,,.

HA.TCH DOOR OPUATJN6 LEVE!t("9079·8JS ) _ /ij /.

SO¥ ~UPPORT·BEEH IV E (4079-3188)

ANTt'NNA NUL I ( OADING COIL IN STL . (6079·Z707)__/ /

" PE!ic·;,·:~i"'s,..~ ... ~.s,t/~S...~~$""t./6;;: ;tbs) ·

.SEAT TILT CHA lit ( CR 756/)e @ 5 £'AT TILT CHAI/l. (CR7 %1 ) __/ • RCCF IV L~ l lti5TAi.t.AT I ON(~07!}-.S 1 4.$) "-----..J....MES S t. FO(J D GEAR CAAINET ( 5079- -IZ33 ) RIGGER's CA81#ET (S0 79-4t$2) MUS SHEi.I' ' IN STALJ..ATIOt:ol ("f.079- 11 39) I"/14~EL (60'7'9 -7A) Y /I{ $TALl.ATION (6019- 10 <4.,) HEAT I NG SY.STI!-Irl (6079 -5803) INSTRUNIINT PANEL (<#-079 · ~99') A IR SYSrEM / NCAR {408 .0 ~ 1 253) '-AlJ)(il,IA~Y iii601E CO/YTROL$ (,079 -S'7'49) -Fill£ E~TINr31./ISHlli.. - .51ZE S . AUX . UENEI?ATOR. COI,'T~OL F'ANEL (,079-f,So}-- . - · THROTTU CONr~OJ..S (607 9- +2S-f) · OIL TANK ; TI/8/NG II,'S TAL . -JA/1'/~AN(I 6lN.(607_9-"'f916) I TILT CHAJA · (C R. 756/)e iAW"'ANC E ~ENE!lATOif.

.t M . A . ./). !tACK GiN~RAL .. usy, ( "-079 -$.5'!}0} CLECTRICAL /NSTALLATIOIV(,07' -SS 21) E..{TfiUOK ~OM8 RA CK INSTAL . D07!J-Z9t<f) ' B UN .(' INS TALLA TION (607.9 -22.48)

@ RECt.M<IING CHAIR ~SO ----- ----_/

,,"£OO.R. L.AYOVT ( "079 . -.HI?) - ' / / ' T.ONI( SUSPEN5!0AI (6019 • 21.~)2 )

. CEILING (~079 -/1~3) _./ · ·/

e RECL/N I NG CHAIR'"'i~o ~/

NOTES:

"--- cH EA.-1 /C At. PK PA,ER NO.tDER ( l>07!}-~90

/'f/EL DISCHA,(,GF (<.07!<- .:Z IS) / '.. --- 5 QJ UO ro Y ao•ert'<o79- • - u J . YVAT~R TANK (6079 ' -S!J06 -l)

I.-@ INDICATES I NSTHl~TIONS . INSTALLED AT

"---- W~L "ACK ( LO $'906 -2!i)

WAS'H STAN.O (,07 9 -5"~06 -12.)

WINGfDOT lA Kf

MAJOR CMTROi.S A5SFM6LY 79 -5'901.-10) ( b079 -l.rof)

~ TOI-'\ItEJ. ~CX (G07 9 -.~906-"T)

Z. - VIEVVS fROM CfNT!R OF SHIP-lOOKING OUTBOARD

DR..A.t;, · ll.OPE BOX ("f079 -1911) - _____/ ~EAR · RI!SC .t..IE COORS ('6079 -.f30 0) -

~

~AND RAIL

ASSEMBLY ('079 -4465) SPLIT VIEW OF CONTROL CAR

/lEAR. lA,DPER. {<f.O!~ -f2Z. r)

K -123 ant/ Fufure

K-TYPt AIRSHIP

:•

~ ~ '-"'

..._'

v-a

Next: LexTest_2014_08_18_07_36_30_711 →

LexTest_2014_08_18_07_36_30_711

========= IV. ELECTRICAL SYSTEM========= References: 1. Equipment Manufacturer's Manuals 2. BuAer Manual 10-201 to 10-205.

A. GENERAL DESCRIPTION .. ' The electrical system comprises an 800-cycle, 120-volt AC supply, and a 24-volt DC supply. The DC supply operates in connection vd th two 12-vol t storage batteries. The batteries are connected in series.

The system as a whole includes three separate power producers, namely, the port generator, starboard generator, and Lawrance auxiliary power plant.

CAPACITY IN P~PERES 110-Volt, 800-Cycles or PRODUCERS 24-Volt DC Port Generator 7-9 25 Starboard Genera to I · 7-9 25 120-Volt, 800-Cycles Auxiliary Generator 41.7 167 Amp. @ 30 Volts.

The DC output of any or all genera tors cEm be thro wn on the line to charge the ba ttery and to supply the DC load.

-86-

Next: LexTest_2014_08_18_07_37_08_734 →

LexTest_2014_08_18_07_37_08_734

C - CONTINOUS

ELECTRICAL LOAD ANALYSIS

M- MOMENTARY (5 MIN. OR LESS) X -OFF

GAC

OF K-51

* -NAVY FURNISHED

SK-5-7567

* * - DURATION OF fliGHT

TOTAL AMPERE . LOADING DURING OPER

TYPE OF

DURATION OF TYPE OF 1--- - -..-----..-----.------1

MANUFACTURER & NO AMPERES

OPERATI NORMAL NORMAL NIGHT BA.TTLE OF

EQUIPMENT

PART DESIGNATION OPERATION

(M OR C) ANCHOR CRUISING CRUISING ACTION POWER SOURCE & CONTROLS GENERATORS -OUTRIGGER •Eclipse 584-lA...NEA-ZE 2 CONTROL- BOX Bolipse BF-lD 2 ~--==~~~~~-- -- - ---- ~~~~~~ ------ ~~ ~----- ~ ~------------+ - ----- -------+ ----- -- -+---- - ---- r -------- ~ - -------+------ ~ AUXILIARY - POWER UNIT Lawrance -Navy Type One 1 ENGINE ,._ ;¥>del 30C · -l 1 I as req11ired

_ _y ENE "'-- RA ~ To ~ R -'------- -1+- •·Model 2Cll41A4 1 L Uot & zg J:gdnfnj

M or C

CONTROL BOX ~~: - _ 3GBD1 -All l I' -f4

RELAY- REV. CURRENT •G.Eo - 3GTR _ 7_2_Al ________ _ _ -t--= l =---f---- - -------+- , ---- ---------

----+ - ·

r- ~~~~~ ==~~~~~~~~ - --~ -- 1 - t - - ! -- - - --+---- - --+--- --- --+- --------+------- ~ STARTER- CONTACTOR •G.E. - 3GTR72Bl BATTERIES •li.A.f •. 1062-34 2 34. Ampere Hrs •.

----+-----------------+----- --~ ------ ~ C7 ~-- - - ~ r-C~O ~N_ V~E~R _ T ~ E~R=S ______________ ~~~B~c~l~i~ant~-~8~0~0~-~l~-~B~-- -----+~ 2 ~~ 62~.!~.~~~~~~~~~~~ -- --~~ C~ ----~ S~e~e ~ N~o~t~e#~~ - - •~6 ~ 2 ~.0~~~ 6~9 ---r-- 6 _ 2 ~ ._ 0 __ , A-PERSONNEL EQUIPMENT . GE Grill GRILL - STOVE - OVEN 6.7 AC 1 6.7A G 120 V. X ~.!_7 3 to 4 hrs da C X

c

3 to 6 hr s/ day ---t-- c =-------t----==------+----=--=----i-

Manning Bowman #494 PERCOLATOR 1 3.0A @ 120 V. X 3.0 AC 3.0 AC X ROASTERETTE Ever hot

1 3.0A o 120 v. 2 to 3 hre/d&J C X 3.0 AC 3.0 AC X

TOASTER -·- ~ - - ": :- -- · -- -- -ARMAMENT BOMB-DOOR SOUNDEBUOY 4~0 A 0 2• V. , While on patrol 4.0

1 c X 4.0 4.0

-ENGINE HEATER - OIL SERVICE TANK E. L. Weigand - Navy Type C (Shore Connecti -on) 2 ooow - 120 v.

HEATER- AUXILIARY

UNIT i!Jurnlah9d with Lawrance Uni OA @ 24 Volta A.e required c

1 X 10.0 10.0 10.0 HEATER- ENGINE STARTER 2 300 A C 24 V. (While starting Eng ne) M $TARTER - SOLENOIQ SWITCH 2 1 A (!l 26 V.

" " "

MESHING - SOLE~OID_j)EVJCE 2 )(

" "

BOOSTER COIL M A @ 18 V 2 1 8

"

" "

TRANSFER PUMPS -FUEL -LIGHTING LANDING LIGHT Grimes Mfg.Co. 8T 1220 A 1

lOA @ 24 V • Night Lan ding Only c

X X 10.0 X SPOTLIGHT Unity Mft .• co. DelllXe 6 len . 6.6A A 28 V.

1 Aa re c X 6 6 X X GAC per Dwg, RUNNING LIGHTS - CAF\ 12079-1606 3 X 0.6A C 28 V. Night c 1.8 1.8 X RUNNING LIGHTS - ENVELOPE GJi.C See Note #2 *** 7 0.6 A 0 28 V.

c X X 4· .2

4.2

"

" "

11\lr'\ lrA Tf"\0 1 lf.J-4T' Grhea #A2328 6 As req11ired

0.17 A C 28 V. c X 0,86 0.86 0.85

-

,( -ENGINE

HEATER - OIL SERVICE TANK E.L.Weigand - Navy Type C 2 ooow - 120 v. (Shore Connecti-on)

'\'urnlsh9d with Lawrance Unlit_ As required

HEATER- AUXILIARY UNIT 1 OA @ 24 Volta c X 10.0 10.0 10.0

HEATER - ENGINE )( STARTER •Eclipse. Series ll.Tyn~A6gV 2 300 A G 24 V. (While starting Eng ne) $TARTER -SOLENOID SWITCH • Eollpee Type 616 Model 2A 2 1 A (!l 28 V. M

" " "

)( •Eclipse, Series 1l,iY~ soo 2 MESHING- SOLE~OID_j)EVJCE

" "

M BOOSTER COIL •Eclipse,Type 613 Model 7A 2 1.8 A @ 18 V.

" "

"

TRANSFER PUMPS - FUEL ..

l t:..- LIGHTING Grimes Mfg.Co. 8T 1220 A 1 lOA @ 24 V. .Night Landing Only LANDIN<;; LIGHT c X X 10.0 X SPOTLIGHT Unity Mft.co. De111xe 6i" len . 6.6A A 28 V.

1 As - req11ired c X X 6 6 X GAC per Dwg. X 1.8 1.8 12079-1606 3 0 .6A C 28 V. Night operation on]J 0 X RUNNING LIGHTS - CAF\ GJi.C See .Note #2 *** 7 0.6 A 0 28 V.

RUNNING LIGHTS - ENVELOPE c X X 4· .2 4.2

"

Gri'lleB #A2328 As req11ired

6 0.17 A C 28 V. c X 0.86 0.86 0.86

INDICATOR LIGHTS SIGNAL LIGHT Grimes K-3 NAF 1171-2 1 6.3A G 24 V, M 5.3 5 3 6 3 5 3

"

G.a.C

2 0.6 0 24 v. c l 2 l 2 1.2 1 2

~R LIGHTING

"

Fairchild

"Moong1ow" 1 0.2 A @ 24 V. c 0.2 0.2

NAVIGATOR'S LIGHT 0.2 0.2

"

G.A.C

RADIO TABLE LIGHT 0.17 A 0 24 V. c 0.17 0.17 0.17 0 17

" "

Gii.C

2 0.17 A G 24 V, c 0,34

PANEL -INCANDESCENT X 0.34 0.34

"

0.2 A 0 24 V. c 0.6 0.6

PANEL - ULTRA VIOLET 0.6 0.6 NAF 1192-l

" "

- F-RADIO

c

MAIN TRANSMITTER 1 AC 5.8A 0 28V Ali req11ired 6.8 AC 6 8 AC -westinghouse tU.'_-7 6 8 AC 5 8 AC Same TRANSMIT Same

STANDBY ••

- ~eetern Eleotr1o BU-19 .Not Available ** MAIN RECEIVER -t ~, INTRA-SQUAD TRANSMITTER ~estern Electric GR-12 - ---- ·-- ·· --- - ) !

_ _ TRAJ::!§. MIT See .Note #3 !

••• 7 .o A C 28 V. ** c 7.0 7.0

STANDBY 7.0 7.0 INTRA-SQUAD RECEIVER 4Weetern Electric RU -17 ! . li MARKER BEACON RECEIVER l

24 v. ** 2,6

Kagnavox Co. RL24C 1 2.6 A. c 2.6 2.6 2.6

INTER PHONE ;;

RADAR • bH 9:U I ~~v c X bH 9:~ ~8 ~:~

1 tg *:~

4BO.l - DZ-2A 1 1.6 A 0 86 V. **See Bote #4 ••• 0 X 1.6 1.6 1.6

DIRECTION FINDER 1.25 1.26 1.26 A G 26 V. AB reqlllred ll 1.26 1.26 FREQUENCY INDICATOR •Bendix Ba4io - LK7 4Western Eleotrio-ZBl or ZB3 1 1.26 A • 26 V. M 1.25 1.26 1,26

HOMING EQUIPMENT " X

"

5.5 5.5 ~BK 1 6.6 A 0 28 V, ** c X 6.6 l.f . F. SYSTEM

..aarlt IV 16 A 0 24 v. c X 16.0 16.0 16.0

M.A.D . SYSTEM 1 ••

MISC . RADIO EQUIPMENT - - -- li.Av per .11Wg, fZU ' /11-.lOUO RUNNING LIGHTS - CAR V ,OA IQI l::O V, RUNNING LIGHTS - ENVELOPE GAC See Note #2 • • • 7 0,6 A 0 28 V.

c

X X 4,2 4,2 Grhea tA2328 6 0,17 A @ 28 V, As required

c X 0,86 0,86

0,86 ~-- ---------------------- ~-------·-------------- ----~~--+----- -- - ------~----------------+--------4--------~ --------~-------+-------- ~ C-ENGINE HEAlER- OIL SERVICE TANK E.L.Weigand - Navy Type C 2 OOOW - 120 V. (Shore Col)neoti-on) ~~H~E~A~T~E~R_-~A~U~X~I~L~IA~R~Y~U~N~I~T-- --~-- ~~r~n ~ l ~ s~h~~~d~w~i~th~L=a=w~r~an~c~e_U~n=i~~_! - ;~O~A~@~2~4_V~o~l~t~s~~A=s~r~e~qu=i=r~e~d~----~~C~----+-~X~---4-=1~0~,0~--~-=l~0~·~0 ---+~ 1 ~ 0 ~ · ~ 0 -- --; !

HEATER - ENGINE

STARTER •Eclipse, Series ll,Tyn~~5g? 2 300 A c 24 v. (While starting Eng ne) M

~TARTER-SOLENOI ~ D ~ S ~ W ~ I ~ T~C ~ H -- ~~ · ~ E~o~l ~ i ~ plse ~ T~~y~p·e ~ 6~1~8 ~ M~o~de ~ 1~2~A ~+- ~2 -- ~l~A~@~2~8~V~ , -- ~ -- -"-------"------~"+---~M~--4---------~------~--------+- ------ ~ MESHING - SOLEt:JOID DEVICE • Eo 11 ps e , Series 11 •-iYoS~.J .::. O .::. O I-~ 2 ::.__-t----------- --+----"-------"'------"~--~)(=--- --+--------4-------- ~-- ------t-------- -l BOOSTER COIL •Eolipse,Type 613 Model 7A 2 1 8 A @ 18 V " " " M TRANSFER PUMPS- FUE ~ L ~==~~ ====~ ====== ========== ==~====~============~============~-=~~====~b========F========+== ====== ~ ====== ~ IE- LIGHTING LANDIN~ LIGHT Grimes Mfg,Co, 8T 1220 A 1 ' lOA@ 24 V, .Night Landing Only C X X 10,0 X SPOTLIGHT Unity Mft,Co, Deluxe 6-f'' len 1 . 6.6A A 28 V. As required C X X 6 6 x RUNNING LIGHTS- CAF\ GAC per Dwg, 12079-1606 3 0,6A l!ll 28 V. Bight operation onl.l C X X 1,8 1,8 RUNNING LIGHTS- ENVELOPE GAC See Note #2 ••• 7 0,6 A@ 28 V, " " C X X 4 · ,2 4,2 INDICATOR LIGHTS Gri11ea t.A2328 6 0,17 A@ 28 V, As required C X 0,85 0,86 0,85 11 11 SIGNAL LIGHT Grimes 1{-3 NA.i' 1171-2 1 6,3A C 24 V, M 5 3 5 3 6 3 5 3 ~R LIGHTING G.a.C 2 0,6 <; 24 V, " C 1.2 1 2 1.2 1.2 NAVIGATOR'S LIGHT .l!'airchild "Moonglow" 1 0,2 A @ 24 V, " " C 0,2 0,2 0,2 0,2 RADIO TABLE LIGHT GAC 1 0,17 A C 24 V, " " C 0,17 0,17 0,17 0 17 PANEL-INCANDESCENT Ga.C 2 0,17 A C 24 V, " " C X 0,34 0,34 0,34 ~-PA - N -- EL __ -_u _L _ T_ R _ A __ V _ IO _ L _ E _ T --------~ N - AF --- l - 1 _ 9 _ 2 _ -1 _________________ ±= 3 __ ~ 0-· _ 2 __ A __ 0_2_4 __ V_. __ ~"------"----------+----C----~-0 - · - ' -----r--0- .6-----t-0 - , _ 6 ____ -i_ o_._ 6 ____ -4 ~-- ------------------~+--------- - --------------+- --4-----------~---------------+-------+------~------~r-------~-- -- ~ F -RADIO

MAIN TRANSMITTER "WeetinQ:bouse GP-7 1 AC 5,8A @ 28V Aa required c 6,8 AC

6.8 AC 6 8 AC 5 8 AC TRANSMIT Same STANDBY. Same •• MAIN RECEIVER - -weahrn Eleotrio BlJ -19 -+ 1 .Not Available •• ~ ~~~~~---------- ~ ---------- t -- i __ G _ R_l_2_ •. -~ l ~ _ ) -+~~~~~~------------~-------+------~---- --4--- ----+------4 ~I.RA =SQl,!f-D TRANSMITTER "Western Elec r o - 1---- TRANSMIT j )

c 7,0 7,0

7.0 ~ --~ S ~ T ~A~N~D~ B~Y ~-------------- U-S _ e _ e ~ N _ o _ t_e ~ #_ 3 __ • _ • _ • __________ __ ~~! - ~ 7~· . 0 ~ A =_ C 28 V, ••

INTRA-SQUAD RECEIVER <~Western Eleotrio RU -17 ! .1 i

MARKER BEAC~O~N~RsE~CsE~IV~E~R~~-r - ------ -----------------4----~---- --~---+----------------~--------~ ------ ~ -------1--------+-~~---~ INTERPHONE Kagnavox Co, RL24C 1 2,5 A. 24 V, •• 0 2,6 2,6 2,6 2,6 DiRECTION FINDER 4<ROA - DZ-2A 1 1,6 A 0 86 V, •• See .lfote /}4 ••• 0 X 1,6 1,6 1.6 FREQUENCY INDICATOR •Bendix Ra4io _ IJ17 1 1,26 .l @ 26 V, AB required )( 1,26 1.26 1,26 1,26 HOMING EQUIPMENT 'Western Eleotrio-ZBl or ZB3 1 1,26 A 0 26 V. " " ld X 1,26 1.26 1.26 l.f.F . SYSTEM *.1 - BIC 1 6,6 .l 0 28 V, •• C X f1,6 5.5 5,5 M .A .D. SYSTEM 4Uarlt IV 1 16 A 0 24 V, •• C X 16,0 16,0 16,0 ~IS C . RADI -"= 0 --'=- EQ:!.U:::.:I::..P.:.:M :=. E ::.. N :...: T ____ __..~ -- --· ___ _____ ----- -- -----+- ---+-------- -- --+-- ------------------ ~---- - ----+------ ~~-----~-- ------+-~-- ---1 F-RADI O MAIN TRANSMITT ER AC 5,8A @ 28V Aa re uired

c

6 8 AC 6 8 AC 0 8 TRANSMJT Same STANDBY. Same

••

tv1AIN RECEIVER "W .. hrn Eleotrio Bl.l-19 1 Not Available •• r-'-'IN~J" ~_ R ~ A ~ ._ -~ S =.:: Q ~L!:.!.~.'C.' D ~ T = R = A=N=S=M=fT=TE= = R ===~= ="W~e~a~t~e~rn~ ~ E~l~e~o~t:r~ic~=G~R~-~1~2 =-_-+ __ -f f -...:_ ,:tl:)~t~~~ ~=-- ~~-=-~~=--~1r-~~~~--~ ~~~ ~~~~~~~t~~~~ ~~~~ t~~~~~~~~t~~~~~~- - ~t~~~~~~~~f..-~~~~~~~-l TRANSMIT ) r- --~ S ~ T ~A~N~D~ B ~Y~-------------- H-S~e~e ~ N~o~t~e~# ~ 3 __ •_ • _ • ___________ ~~ -~ 7~~ - ~28 _ V · ~·~-·-•---------------4--~C~--~~ 7 L 0 ~---+~ 7 ~·~0~---+~ 7 ~·~0~---4 - 7 ~.0~--~ INTRA- SQUAD RECEIVER <~Wee tern Electric RU -17

c

RADAR • 1 0 X DiRECTION FINDER 4<RCA - DZ-2A 1 •• See .lfote 114 ••• 0 X FREQUENCY INDICATOR •Bendix Ra4io - IJI7 1

1.26 .l @ 26 v. Aa required )(

1,26 1.26 1,26 1,26 'Western Eleotrio-ZBl or ZB3 1 HOMING EQUIPMENT 1,26 A 0 26 V.

.. "

1,26 X 1.26 I.F .F . SYSTEM *.1 - BK 1 6 .li .l 0 28 v.

•• c X

5.5 5.5 M.A.D. SYSTEM 4Uarlt IV 1 16 A 0 24 V.

•• c

X 16,0 16,0 16,0 MISC . RADIO EQUIPMENT G-MISCELLANEOUS MAPPING CAMERA INSTRUMENTS

ot A o 28 Volta 0

•• .o 4.0

REMARKS Power Souroe 0 nt 1n oue Komentary TOTAL CONTINUOUS LOAD 11 67 122 06 143 66 127 62 Oabi r Generat . on ADDITIONAL MOMENTARY LOAD 7,80 7,80 7,80 Lawrante Generator 18,22 129,86 TOTAL LOAD 161.86 136,32 U<~iiote #1 .

Converter used to supply A,O,Load, A.C. loads not included in totals since Converter D.C.l oad is shown • .. <!~Note #2.

Per G.A.C.Drawings #3080-Bo, 61071-796 , Ba 61021-782.

••"''.!o te 13.

Standby and Receive 6,6A ® 28 Volts, and 7,0 A on Transmit . •• ••~~t~ ote #4.

Momentar~ 3 ,6 A relay ouiTent.

-...:J I

Next: LexTest_2014_08_18_07_37_55_117 →

LexTest_2014_08_18_07_37_55_117

B. DISTRIBUTION The electrical system is distributed from two panels, the auxiliary panel on the starboard side of the car between frames 5 and 6, and the mechanic's main panel. All the AC system and the DG ol:ltput of the auxiliary generator come to the auxiliary panel. The DC output o. f the · port and star- board generators come to the mechanic's panel. See Fig.

XVIII and Fig. XXXIII.

NOTE: K-3 thru K-29 - as stated below.

K-30 & Future - see installation of Lawrance auxiliary generator.

The auxiliary panel e arries a selector switch to connect the AC loads to the generators in various combinations in a, ccordance with the following table which is reproduced on the panel: SWITCH POSITION 1 2 Starboard Generator Radio Off Cook Cook Cook Radio Off Radio Off Cook Radio Off The cooking loads consist of a roasterette, a hot · plate and ~percolator. A cooking panel equipped with a selector switch makes it impossible to connect more than one load at a time.

The battery can be disconnected from the system by means of a safety switch located in the main junction box under the mechanic's panel and controlled both from the pilot's instrument panel and from the mechanic's stand.

-88- H H

§

• t!)

H r:r..

-89- The generator switches of K-11 ships and future are equipped · with the thermal overload devices which operate when the normal load is exceeded.

To reset a generator switch after it has tripped open, wait until the overload device has cooled, and close the switch again.

C. CONTROL BOXES AND CUTOUTS There is a control box and a cutout for each generator.

The control boxes are · the -carbon pile type. See Fig. XXXIV.

(1) Carbon Pile Regul~tor No adjustment or repairs should be attempted in flight on the carbon pile regulator.

(2) Service Troubles (a) If the DC - voltage output is erratic or low, check all connections to be sure they are clean and tight, and examine voltage regulator plug in connections for cor- rosion or poor contact. Spread plug in prongs, if necessary, to insure contact. If the regular contacts are dirty or pitted, th~y should be cleaned as instructed under "CONTROL BOX INSPECTION."

(b) If at any time the voltmeter shows a reversal of polarity by r2ading off scale in the wrong direction, or if the voltage reading is not more than 4 or 5 volts, the -90- FIG. XXXIV GENERATOR CONTROL BOX AND BATTERY INSTALLATION -91- indications are that either the DC field has been inadver- tently "flashed" in the wrong direction, or that the generator is operating on residual magnetism only. To "flash" the field, remove the (A+) lead from the generator and momentarily close the generator cutout contacts, making certain that the external connections to the battery are correctly connected with regard to polarity~ (c) If the ammeter indicates zero charging current when the generator voltage. is above 13.5 or 26.8 volts for 12 or 24-volt systems respectively, check the operation of the generator cutout contacts. If the contacts are open, the unit is out of adjustment and should be reset in accord- ance with manufacturer's cutout instructions. If the contacts are closed, check th~ charge on the battery, since the charg- ing current drops down to a low value when operating with a · fully charged battery resulting in li tt~e or no ammeter indication.

(d) ·· If the AC voltage output is below the normal 120 volts (=5%), check the DC voltage output and readjust to proper value as instructed under "CONTROL BOX INSPECTION. ·" -92- Switches (Cont.) Location Navigation lights, running Mechanic's panel.

lights, instruments light, galley light.

(2) Automatic Controls Port and starboard generator's Back of mechanic's main control box. junction.

Port and Starboard cutouts. Main junction box.

Aux. generator control box. Aft of auxili a ry pane.

(Location ch a nged K-30 & Fut.)

Aux. gener a tor cut c· ut. Aux. panel junction box.

(Aux.panel K-30 & Future).

Blinker Top of mechanic's stand.

(3) Instruments 3 A.C. Ammeters and 3 A.C. Auxiliary panel.

Changed K-30 & future.

voltmeters for port, star- (No A.C. Ammeter bo a rd and aux. generators.

(One A.C. Voltmeter 1 D.C. ammeter and 1 D.C. Auxiliary panel.

voltmeter for aux. engine .

2 D.C. ammeters and 2 D.C. Me chanic's pan el.

voltm e ters for port and st a r- board generators.

(4) Cooking Galley p or t side, frame 6.

Percolator, roasterette, hot plate.

(5) Lamps See pages 95 to 98 Incl.

for LamJ: Data.

(6) Fuses See pages 99, 100, and 101 for fu se data .

-94- NO.

NAF TRADE LAMP BASE VOLTS LOCATION CP BASE TYPE 'XJ NO. NO. TYPE CONT. REQ'D 1-'· OQ .

S.C.

309 S-11 32 28 Cand-Bay Nose Cone 1 D.C. _ Envelope 306 S-8 15 28 Cand-Bay 2

s

306 S-8 15 28 Cand-Bay D.C. Fins and Tail < I D.C. Outrigger 2 306 S-8 15 28 Cand-BaY..

PJ Cand-Bay D.C. Car-Running 1 306 S-8 15 28 D.C. Car-Ceiling 306 S-8 15 28 Cand-Bay t:f.l Flasher Box 1 T-3 .17A 28 Min-Screw '0 P> Pull-Knobs 11 .17A 28 Min-Screw 1477 T-3 t-j Panel-Inclinator (1) .17A 28 Min-Screw 1 .f.

1477 T-3 D.C. 1 28 Cand-Bay 5-0-5-Incl.

1068-23 302 3 T-4i t-' P> D.C. Pilot's Panel 2 G-6 6 28 Cand-Bay I s -.() D.C. Flight Panel 2 '0 6 28 Cand-Bay 304 G-6 \J'\ D.C. El Indicator 1 G-6 6 28 Cand-Bay I t:::1 ll' D.C. Nav-Inst. 1 G-6 6 28 Cand-Bay c-t

s.c. Nav-Compass p.l

3 1 .f.

**

S.C. Pilot-Compass 1 .f.

*'~ 3 s.c. Nav-Table 1 .;.

T-3.!. .17A 28 Min-Bay 1068-20 313 :;>;~ S.C. Radio Table I 1068-20 .17A 28 Min-Bay 1 .f.

313 T-31 VJ Spotlight Pref-Flange S.C.

.9A 22 1 .f.

c-t Landing Light .

ST-1220 28 1 .f.

* ::r Min-Screw Oil-Pressure 2 t-1 .17A 28 1477 T-3 c: Cand-Bay D.C. · Mech-Panel 3 G-6 6 2$ ~ .!.w Aux-Panel 1 4618 125 *** I Hot Plate Jet Box 0' -*** 125 3

4618 !w

Sealed Riggers Cabinet PAR-46 5.5A 28 1 .f.

*'~** NOTES:.f. Original Lamp by Equipment manufacturer.

* For Grimes Landing Light.

G. A. C.

*- * Koll sman Compass Light .

~ - *-l!- Bryant #4618 for Bryant Base #9446.

SK-1-5953 *-lHf-* For Grimes Model K-3 portable signal light.

NAF TRADE LAMP BASE NO.

VOLTS BASE TYPE LOCATION CP >r) No. NO. TYPE CONT.

REQ'D 1-'· Otl ~ 309 Cand-Bay S.C. Nose Cone 1 S-11 32 28 ~ I 306 S-8 15 28 Cand-Bay D.C. Envelope 2 ~ I 306 S-8 15 28 Cand-Bay D.C. Fins and Tail o' s.~.

305 S-8 15 28 C~nd-B ,ay Car-Running 28 Cand-Bay D.C. Car-Ceiltng 2 306 S-8 15 (/) .17A 28 Min-Screw Flasher Box 1 1477 T-3 'd PJ s.c.

1068-20 313 .17A 28 Min-Bay Pull-Knobs 11 T-3!

<D 1477 T-3 .17A 28 Min-Screw Panel-Inclinometer 1 ~ Cand..,....Bay D.C. 1 1068-23 302 3 28 5-0-5-Incl.

T-4i t-l Cand-Bay D.C. Pilot ' s Panel · 304 G-6 6 28 ~ ~ D.C. 'd G-6 6 28 Cand-Bay Flight Panel 2 I 304 ~ D.C.

.304 G-6 6 28 Cand-Bay El Indicator 1 tJ Pl *-!} I S.C.

3 Compass-Rudder 1 .;.

"'

cT Pl S.C. 1 .;.

3 Pilot-Compass ..

**

.17A 28 Min-Bay S.C. Nav-'l'able 1 .;.

1068-20 313 28 Cand-Bay D.C. Radio Table 1 1068-23 302 3

~=it

~ Spotlight I 22 Pref-Flange S.C. 1 .;.

.9A --J S').'-1220 28 Landing Light 1 .;.

*

f)) .17A 28 Min-Screw Oil-Pressure 2 1477 T-3 t:l p, G-6 6 28 Cand-Bay D.C. Mech-Panel 304 3 ?f.-~ - * l..VJ 4618 125 Aux.-Panel 1 ~ v" \, I -,,-n~- 4618 125 Hot Plate Jet Box

lw 3

- ~ - * - ~ - * 1 .;.

PAR-46 5.5A 28 Sealed Riggers Cabinet -- · -- · ----- ' - NOTES:f. Original Lamp by Equipment manufacturer.

* For Grimes Landing Light.

G. A. C.

** Kollsman Compass Light.

*-~* Bryant #4618 for Bryant Base #19446. SK-1-6420 *-**"'~ For Grim· ?S Model K-3 portable signal light.

txj NAF TRADE LAl il P BASE NO.

CP VOLTS BASE TYPE LOCATION 1-'· ' NO. NO. TYPE CONT.

RE Q'D ~ >< S.C.

1068-20 313 .17A 28 Min--Bay Flasher Box 1 T-3!

- ~

I 1068-20 • 17A 28 Min-Bay S.C • 313 Pull-Knobs 11 T-3t 1068-20 .17A 28 S.C. Navigator T~ble 313 Min-J?ay 1 1- 1068-20 .17A 28 Min-Bay S.C. Mech-Oil Press.

313 2

~=~I

tn "0 1477 T-3 .17A 28 Min-Screw Pilot Panel-Incl. 1 1- ~ T-41- - S.C.

1068-17 301 28 Cand-Bay 5-0-5 Incl. 1 3 1-i co D.C.

1068-23 302 28 Cand-Bay Radio Table 1 T-4l 3 6 28 Cand-Bay S.C. t-1 1068-18 303 G-6 Pilot's Panel 2 Ill 1068-18 6 28 Cand-Bay S.C. Flight Panel 303 G-6 3 a "0

1068-18 G-6 6 28 Cand-Bay s.c. Mechanic's Panel

303 3 I 28 Cand-Bay S.C. Car Ceiling 2 t:::l 305 S-8 15 -.() ~ --..1 S-8 28 Cand-Bay S.C. Car Run:hing 305 15 3 c+ I $ll 305 S-8 28 Cand-Bay S.C. Fins & Tail ..

S.C. Envelope 305 S-8 15 28 Cand-Bay 2 ~ 28 Cand-Bay S.C. Nose Cone 1 309 S-11 32 I -.() Spotlight • 9A 22 Pref-Flange S.C • 1 ?E- ST-1220 28 Landing Light 1 c+

~

~ *- ~ - Compass-Pilot 1 1-i 1- -)Hf- c Compass-Rudder 1 1- -X - ~ (- J...w 125 Auxiliary Panel 1 4618 ~ I - ~- ~(._~ 125 Hot Plate Jet Box

4618 !w 3

\.1\ - ~** ~~ PAR-46 5.5A 28 Sealed Riggers Cabinet 1 1- - -- ------ NOTES: r Original Lamp by Equipment manufacturer.

* For Grimes #ST-1220 Landing Lite.

~h~ Kollsman Compass Light.

-> *- *~ !- Bryant #4618 for Bryant Base #19446. G. A. C.

?HHH f- For Gri m es M odel K-3 -. portable signal light.

SK-1-6404 LAMP BASE NO.

NAF TRADE ' CP VOLTS BASE TYPE LOCATION NO. TYPE CONT.

NO. REQ'D S.C.

s~8 15 Cand-Bay Run.Lights-Car 3 305 26 S.C. Env.

S-8 15 28 Cand-~ay 3 .305 toa:J

" "

Cand.:..Bay 1-'• 28 S.C. Fin.

S-8 15 3 (I'Q

"

Cand-Bay 1 S-11 32 28 S.C. Nose Cone 1068-26 • s.c. Pome Lights 2.

S-8 15 28 Cand-Bay Min-Bay S.C. aelium Valve Lgt 2 1068-20 313 T-3i

s.c. Navigator Light 1

28 Min-Bay 1068-20 T-3!

~

28 Min-Bay s.c. Radio Table 1

T-3 1068-20 313 p..

} 28 Min-Bay S.C. Mechanic Panel 1068-20 313 T-3 28 Cand-Bay s~c. Inclinometer G-6 3 1068-17 CIJ ~ I» 125 Hot Plate Bryant I 'i -.!) Junction Box (1) 3* <» t-t I (Neon-lite) 1/4 Watt 1192-9 24-28 Ultra-Violet~ Pilot's Panel 2

~

fluorescent t:1 I» cT 24-28 Ultra-Violet Mechanics :Panel 1 I» 1192- 9 fluorescent ~ 1 I RPrll 0.9 amps 22 Pref.Flange S.C. Spot Lite (Unity) \J\ J-1 (100 hour) Landing Lite ST1220A 415 24 go (Grimes)

d

Grimes Sealed Beam 1 Par-46 5.5 amp 28 Signal Lite Gun 1171-2 cT • Rudder Compass 1** Kollsman #71-900 3 Light.

*Bryant #4-6/8 lamp for Bryant Base #19446 GAC SK-1-7657 **Bulb for Kollsman #230B Light Ring Fig. XXXVI-a ELECTRIC FUSE DATA: K-3 thru K-8 Cat. NAF No.

Rating Type Purpose Location No. Number Reqd.

Amps.

10 4AG AC Port Gen. Auxiliary Panel 1 1095 1034-4-10 4AG AC Stbd Gen. AUxiliary Panel 10 1095 10.34-4-10 1 10 4AG AC Aux. Gen. Auxiliary Panel 109.5 1034-4-10 1 10 4AG AC Spares Auxiliary Panel 1095 1034--4-10 2 HiAmp DC Aux. Gen. Aux. Cont. Panel 60 1235-60 1034-6-60 1 HiAmp DC Aux. Spare Aux. Cont. Panel 60 1235-60 1034-6-60 1 HiAmp Engine Gdn. Main-Jet. Box 50 1235-50 1034-6-50 1 HiAmp Eng. Gen Spare Main-Jet. Box 50 1235-50 1034-6-50 1 5AG Radio Main-Jet Box 30 1169 1 5AG Radio Spare Main Jet. Box 30 1169 1 20 4AG Spare Mechanic Panel 1097 1034-4-20 1 4AG Starter Control Mechanic Panel 20 1097 1034-4-20 1 20 4AG Oil-Press Mechanic Panel 1097 1034-4-20 1 20 4AG Instruments Mechanic P~nel 1097 1034-4-20 1 20 4AG Panel Lights Mechar~c Panel 1097 1034-4-20 1 20 4AG Running Lights Mechan~c Panel 1097 1034-4-20 1 20 4AG Nav. Lights Mechanic Panel 1097 1034:...4-20 1 20 4AG Dome Lights Mechanic Panel 1097 1034-4-20 1 20 4AG Spare Mechanic Panel 1097 1034-4-20 1 20 4AG Spare Fwd. Sw. Panel 1097 1034-4-20 1 20 4AG Dome Light Fwd. Sw. Panel 1097 1034-4-20 1 20 4AG Panels Fwd. Sw. Panel 1 1097 1034-4-20 20 4AG Compass Fwd. Sw. Panel 1097 ' 1034-4-20 1 20 4AG Instruments Fwd. Sw. Panel 1097 1034-4-20 1 4AG Landing Light Fwd. Sw. Panel 30 1099 1034-4-30 1 20 4AG L.L. Motor Fwd. Sw. Panel 1097 1034-4-20 1 20 4AG Misc. Fwd. Sw. Panel 1097 1034-4-20 1 4AG Spare Fwd. Sw. Panel 30 . 1099 1034-4-30 1 NOTE: All catalog numbers by Littelfuse.

G.A.C.

SK-1-6410 Fig. 39 -99- Fig. XXXVI-b ELECTRIC FUSE DATA: K-9 thru K-50 Rating Cat. NAF No.

Type Purpose Location Amps. No. Number Reqd.

10 AC Port Gen. Auxiliary Panel 4AG 1095 1034-4:-10 1 AC-Stbd Gen. Auxiliary Panel 1095 ' 10 4AG 1034-4-10 1 10 4AG AC-Aux. Gen. Auxiliary Panel 1095 1 1034-4-10 AC Spares 10 4AG Auxiliary Panel 1095 2 1034-4-10 Radio 30 5AG Main-Jet. Box 1167 1 30 5AG Radio Spare Main-Jet. Box 1167 . 1 ·Mechanic 10 Spare Panel 1095 1 4AG 1034-4-10 10 Starter Control Mechanic Panel 4Ag 1095 1034-4-10 1 10 Oil-Press Mechanic Panel 4AG 1095 1034~4-10 1 10 Instruments Mechanic Panel 4AG 1095 1034-4-10 l 10 Panel Lights Mechanic p-anel 4AG 1095 1034-4-10 1 Running Lights Mechanic Panel 10 4AG 1095 1034-4-10 1 10 Nav. Lights Mechanic Panel 4AG 1095 1034-4-10 1 Galley Light Mechanic Panel 10 4AG 1095 1034-4-10 1 4AG Spare Mechanic Panel 1095 1 1034-4-10 Spare FWd. Panel 5 4AG 1094 · 1034-4;...5 1 Dome Light Fwd. Panel 4AG 1094 1 5 10.34-4-5 .

Fwd. Panel 15 Panels 1096 1 4AG 1034-4-15 Compass 4AG Fwd. Panel 1094 .1 5 1034-4-5 4AG Instruments Fwd. Panel 1094 1 5 1034-4-5 Landing Light Fwd. Panel 1096 15 4AG 1034-4-15 1 Fwd. Panel 4AG L.L. Motor 1 5 1034-4-5 109i Misc. Fwd. Panel 15 4AG 109 1 1034-4-15 Spare Fwd. Panel 1096 15 4AG 1034-4-15 1 NOTE: All catalog numbers by Littelfuse.

G. A. C.

SK-1-6409 ) -100- Fig. XXXVI-c ELECTRIC FUSE DATA: K-51 & Fut.

Rating · No.

Location Cat. NAF Type . Purpose Amps Req.

No. No.

Port Generator AC Aux.out1et Box 1 10 4AG 1095 1034-4-10 TT n Stbd Generator 1095 1 10 4AG 1034-4-10

"

TT n 10 Converter No.1 1095 1034-4-10 1 4AG

"

tf 10 Converter No.2 1095 1034-4-10 1 4AG

"

If If 10 Spare 1095 1 4AG 1034-4-10

"

Oil Pres.Lite Mechanic's Panel 1 10 4AG 1095 1034-4-10 n Instruments 1 10 4AG 1095 1034-4-10

"

10 Running Lights l095 1D34-4-10 4AG

"

I 10 4AG Navigation Lgt 1095 1034-4-10

"

10 Dome Light 1095 1034-4-10 1 4AG

" "

10 Spare 1095 1 4AG 1034-4-10

"

Spare 1097 1 20 4AG 1034-4-20

"

tl 1097 1 20 4AG IFF 1034-4-20

"

It 20 Naviga tion Table 1097 1034-4-20 4AG

"

20 Starter Cont. 1097 1034-4-20 1 4AG

"

Radio 1099 1 30 4AG 1034-4-30

"

1099 1 30 4AG Spare 1034-4-30

"

n 1097 2 20 Spare 1034-4-20 4AG

"

10 4AG Spare 1095 1034-4-10

" "

Fwd.SW & Fuse Pan. 1 Spare 1094 5 4AG 1034-4-5 fl fl fl Dome 1094 1034-4:...5 1 5 4AG

"

Compass 1 5 4AG 1094 1034-4-5

" " " "

fl II Instruments 5 4AG 1094 1034-4-5 l

"

5 4AG L.L. Motor 1094 1034.-4-5

"

" " "

n 4AG U.V.Light 1094 1034-4-5

" " "

15 4AG Land·ing Light 1096 1034-4-15 1

" " "

" !I

Miscellaneous 1096 15 4AG 1034-4-15 1

" "

fl Spare 1096 1 15 4AG 1034-4-15

" "

"

Spare Main June. Box 1169 1 50 5AG TT II ff MAD 1169 1.

50 5AG 1T tf 30 5AG Spare 1

"

Tl 30 5AG Radar 1

"

NOTE: All Catalog Numbers by Litt1efuse, Inc. GAC SK-1-7658 -101- E. LAWRANCE AUXILIARY GASOLINE POWERED ELECTRIC GEN&qATOR (1) Specifications of the Lawrance Auxiliary Power Unit Model 30 C.:..2: No. of Cylinders Ignition Dual Horsepower 14.5 Output DC (Continu o us) 5KW Weight (pounds) 213 Fuel Oc ta . ne 91-100 RPM Output (5 mins.cont.) 7.5 KW (resting 30 minutes with an 86 amp.load of 28.1 volts.)

(2) Preparations for starting Before attempting to start the engine for the first time, the following checks should be made: (a) At le a st three (3) gallons of lubrication oil Navy Specification 1065 t<Y 1080 should be ple . ced in the oil tarL'l.c.

(b) See that 24 volts of battery are across line and that the main line switches for auxiliary power plc . nt are in "off" position.

Notice: Press in on automatic over-sneed cut G Ut button to make sure switch is in oper a ting position.

(d) Fuel tank should contain 91 octane gasoline. Open valves and check engine dribble va lve for flooding.

(e) By aid of the hand cr a nk, turn the engine · through two or three revolutions. If abnormal effort is required, remove a spark plug from ea ch cylinder to make sure liquid has not collected in the combustion chamber.

This procedure should be followed whenever the engine ha s been idle for a week or more. (See Navy Spec. AN9505a for prepar a tion for storage instructions).

-102- NOMENCLATURE FOR FIG. XXXVII Auxiliary Generator and Blower General Assembly DESCRIPT:ION 1 Lavrrance Generator 2 Mount - Auxiliary Generator 3 Auxiliary Blower - Homelite Ventilation Control Box Duct - Aii~ Intake 6 Air Outlet & Exhaust Assembly 7 Oil Pressure Line 8 Fuel Line Oil Line - To Engine 10 Oil Line ~ Return 11 Oil Tank Vent Line 12 Alternator Box 13 Alternators Air Int a. ke - Alternators Oil Tank lE Support Bracket - Oil Tank 1?

Drain Tube Assembly 18 D.C.Box . 19 A.C.Box 20 D.C.Voltmeter 0-35 V 21 Ignition ' Switch 22 Oil Temp. Gage 0-12ooc.

A.C. Voltmeter 0-150~V 24 D.C. Ammeter 0-480 Amps.

Relay Switch 26 Starter Switch 27 Cylinder Temp.Gage 28 Oil Heater Switch 29 Breaker Switch Alt. #2 30 Breaker Switch Alt. #1 31 Selector Switch 32 Switch - Alt.#2 - On-Off Sv{i tch-Al ternator #1 On-Off Voltage Regulator Meter Mounting Box 36 Oil Pressure Gage Ground wire Lead to Oil Temperature 39 Lead for Cooker A.C.

40 Lead for Radio A.C.

41 Lead for Radar A.C • . 42 Lead to Oil Heater D.C.

Lead to Magneto Lead to Voltage Regulator Lead from Alt. #2 A.C.

46 Lead from Alt. #1 A.C.

Lead to Alt. #2 D.C.

Lead to Alt. #1 D.C.

Power -Lead D.C.

50 Therm· ocouple Lead 51 Lead to Battery -103- ) 10 f II RfHREN([ DRAWINCi - 1'/G. N- vAC SERVICE /3ULLETIN- NUMBER 42.

A5 15 TH RU K- 98 0/Vl!T BLOWER - I{- 99 & FUTURC.

Fig. XXXVII AUXILIARY GENERATOR & BLOWER -104- (3) Starting After the above preparations, the engine may be started in the following manner: (a) Turn fuel valve to "ON."

(b) Turn oil . valve to "0N.

See that generator lead is connected.

(d) Turn starter switch to "ON. n Allow starter to prime engine with fuel and oil pump with oil.

(e) Turn ignition switch to "BOTH" when oil pressure g2.uge · registers pressure.

(f) Turn starter switch to 0FF" as soon as engine fires.

(g) As soon as engine starts, observe the oil pressure gauge and shut engine off immediately . lf' pressure is not indicated. N9rmal oil pressure is 55-65 lbs.

per sq. inch.

(4) Manual Starting If no 24-volt battery source is avail a ble, the engine may be started with the hand starting drum.

(a) Loosen the two Dzus fasteners holding . the st a rter hole cover and remoye the cover plate.

(b) Insert the starting drum shaft until it engages the engine crankshaft nut at the generator end.

(d) Maintain tension on the starter rope to keep the drum engaged.

(e) Turn fuel valve, oil valve, and ignition switch to "ON" positiou-.

(f) Pull rope thru to spin engine crankshaft and start . engine ..

(g) Repeat the process if the engine does not start at fir-st pull.

-105- (5) Warm Up Vfuen the operating temperature is below 21°C the engine will idle at about 1800 RPM after starting. As the oil warms, the engine speed will gradually increase to 4200 RPM (no load).

The governor is adjusted at the factory to operate bet we een 4000 (full load) and 4200 RPM (No load). During warm-up the engine oil hea. ter should be turned to "ON." Normal operating oil-in temperature should be about 60°C. and should not be per- mitted to exceed 87°C. DO NOT USE OIL HEATER BEFORE STARTING ENGINE.

(6) Loading Load may be applied to generator as soon as the engine comes up to speed.

(7) Overload Caution The generator is rated at 5 K.W. (175 amp.) for contin- uous operation. It has an overload capacity of 7.5 K. W .

(263 amp.) for a 5 minute period.

CAUTION: DO NOT operate the power plant above the normal 5 K.W. load for more than five minutes at a time.

Allow 10 minutes at not m ore than o% loa .d between overload eriods for the to cool.

-106-

Overview

Key points

LexTest_2014_08_18_07_23_14_714 View in PDF

UNITED STATES NAVY

· K-TYPE AIRSHIPS

PILOT'S MANUAL

GOODYEAR AIRCRAFT CORPORATION

RESTRICTED

P/2£FAf!E

7A8l£ OF &ONTENTS

.. . . .... . . . . . . . . . .. .. ~ . . . . . . ... Tail Surfaces

5. We:ights and Lift . .. . . .. ... .. . . . . . .... . . . .. . . 2

1. .... .. . .. . . . . . .... . . ... . ... . ..... Static Lift

Dynamic Lift .......•....•.......•.• ·- · ...... . 12

a. Scoops ... . . . ..... . ...... . . . . ..... . . . . . .. . 23

b. .. . . . . . .. . ... . .. . . .. . . . . . . . Valve Settings

h. . . . .... . ... . . .. . . . ... .. .... .... Descending 37

Shifting Air . . . . .. . . . . .. .. ... .. . ... .. . . . . 38

E. HANDLING LINES .....••..•••...•.. . .••.........••.••

c. RECOMMENDED CARBURETOR ADJUSTMENT

•·• ........ . 70

1. Switches ••..•.••.. . ......•.....•...•..•.. -

3. . . . . . . .. ... .... . . . . . . ... . . .. . . Instruments

GENERATOR . . . . . . .. .. .. . .... . ... ... ...... . .. . . 102

3. Starting . . ........ . . . .... . . . . . ..... .. . .. . 105

Warm Up . . . ..... . .. . . . .... . .... . .. . ..... . . . 106

6. Loading ... . . . . . . ... . .. . . .. .... ..... . . . . . . 106

7. ...... . . . . . . .. . . . . .. . . .. . Overload · Caution 106

A. HEATING SYSTEM ... . . . . . .. .... . ....... . ... . . . . 108

B. FIRE EXTINGUISHING SYSTE1! .. .. . .. . .... .. . .. . . 110

D. SERVICE ENGINEERING .. .. .... . .... . . . . . . . . . . . . 111

E. NOTES . . . . . . .. . .... .. . . . .. . .. . . . .. . . .. ... . .. . 112

- VS - % Fullness of Ballonets at Zero

Fig. XXXV Spare Lamp Data Chart .. . .. .... ... .. .. . . - 98

XXXVII Auxiliary Generator and Blower . . . . .. . . 104

Fig .. XXXVIII Heating System ... . .... ........... ... . . 109

PART I

(/Eh'l:R.Al 1J£SfJRIPTIOA'

_,r;_~::~~~-~ - :_ ",,, ... :;~; ~~~!

Length . . . . . . . ... . .. ... ... ... ..... . . . 248.50 251.70

~

Elevators (2) . . . .. ... ... . . . .... . . . 260

GRAND TOTAL - Tail Surfaces .. 1807

B • . AVERAGE PERFORMANCE *

.. . . .... . .... ... 1780 2200 1120 ],.050 1290

- - -

"

"

- - - - - 55.0 34.2

-

"

filtJHT AN!JliJtJHT CfJJYTROL

. · . ..• . :_ ~ .. : ~)~

L = CP

c

Ta = Absolute Air Temperature, oF.= Plus

-

-

-

=

=

=

=

=

= -

=

= -

=

=

=

=

=

=

=

5 =

=

=

=

=

=

LexTest_2014_08_18_07_23_14_714

LexTest_2014_08_18_07_24_42_714

LexTest_2014_08_18_07_27_02_008

LexTest_2014_08_18_07_32_06_131

L----- ....... J Q _ . I i ! I . ; i

..., ______ ---~ .. _ _

.. ______ _:~-------- .. . .. --~--~----; _____ ,.:. _ - ---