Document
N A S A T E C H N I C A L N O T E N *o
-
I n z c L/) z Itw COPY: RETURN m AFWL (WLOL) K I R M APB. N MEX
INVESTIGATION OF LEVEL-FLIGHT
A N D MANEUVERING CHARACTERISTICS
OF A HINGELESS-ROTOR
COMPOUNC -:HELICOPTER
by Jidiun L. Jenkins, Jr., und Perry L. Deul
*, 1 ' I
Lungley Reseurch Center
, Langley Stution, Humpton, Vu.
I,
'I .'*
~ a Y I '__ ' c . ; , r C \ ;>,y x.., 1 -'; ' :0;*,.4L,,/ N A T I O N A L A E R O N A U T I C S A N D SPACE A D M I N I S T R A T I O N W A S H I N G T O N , D . C . J A N U A R V 1970 TECH LIBRARY KAFB, NM 0332573 1. Report No. 2. Government Accession No. 3. Recipient's Catalog No.
NASA TN D-5602
I
4. T i t l e and Subtitle 5. Report Date INVESTIGATION OF LEVEL-FLIGHT A N 0 MANEUVERING CHARACTERISTICS OF A HINGELESS-ROTOR COMPOUND HELICOPTER 6. Performing Organization 7. Authar(s) 8. Performing Organization
I L-6661
J u l i a n L. Jenkins, Jr., a n d P e r r y L. Deal 10. Work Unit No.
~ Performing Organization Name and Address 9.
1 1 . Contract or Gront No.
NASA Langley Research Center Hampton, Va. 23365 13. T y p e of Report ond Per 2. Sponsoring Agency Name and Address Technical Note National Aeronautics and Space Administration 5. Supplementary Notes 16. Abstract The results of a flight-test program u t i l i z i n g a hingeless-rotor compound helicopter are presentec discussed. Data a r e presented to indicate t h e level-flight performance characteristics, speed stability, n v e r stability, a n d wing-rotor l i f t s h a r i n g in maneuvering flight. Also included a r e data indicating t h e rotational-speed c o n t r o l characteristics d u r i n g maneuvers a n d d u r i n g simulated main-rotor power f a i l u The data show t h a t t h e r e i s a n i n h e r e n t reduction in rotor l i f t as level-flight airspeed i s increas I n addition, a reduction in rotor-lift sensitivity in maneuvering f l i g h t was measured a n d determined t c dependent o n t h e stability of t h e a i r c r a f t in maneuvering flight. A l t h o u g h t h e l i f t - s h a r i n g trends coni favorably to t h e piloting task in t h e compound mode, t h e rotor overspeed tendencies c o u l d r e q u i r e con!
pilot attention d u r i n g maneuvering flight.
17. Key Words Suggested by A u t h o r b l 18. Distribution Statement Rotary w i n g Unclassified - Unlimited Compound helicopter Hingeless rotor - Security Classif. (of this page) 19. Security Classif. ( o f this report) 20. 22.
Unclassified Unclassified INVESTIGATION OF LEVEL-FLIGHT AND MANEUVERING CHARACTERISTICS O F A HINGELESS-ROTOR COMPOUND HELICOPTER By Julian L. Jenkins, Jr., and P e r r y L, Deal Langley Research Center SUMMARY The results of a flight-test program utilizing a hingeless-rotor compound helicopter are presented and discussed. Data are presented to indicate the level-flight performance characteristics, speed stability, maneuver stability, and wing-rotor lift sharing in maneu vering flight.
Also included are data indicating the rotor rotational-speed control char acteristics during maneuvers and during simulated main-rotor power failures.
The data show that there is an inherent reduction in rotor lift as level-flight air speed is increased. In addition, a reduction in rotor -lift sensitivity in maneuvering flight was measured and determined to be dependent on the stability of the aircraft in maneu vering flight. Although the lift-sharing trends contribute favorably t o the piloting task in the compound mode, the rotor overspeed tendencies could require constant pilot attention during maneuvering flight.
INTRODUCTION The desirability of increasing the high-speed performance and maneuvering ability of rotary-wing aircraft has been recognized for some time. Theoretical and experimental studies have demonstrated the problems associated with rotor operation a t high speed.
(See refs. 1 and 2.) These studies indicate a decrease in the lifting and propulsive capa bility of the rotor as speed increases. Consequently, in order to maintain the hovering and low -speed capabilities of a rotor while improving high-speed performance, additional sources of lift and/or propulsive force are required.
In recent years, several helicopters have been modified to incorporate various methods of compounding (i.e., the addition of auxiliary propulsion and/or wings) in order t o verify the expected improvements in high-speed performance and t o define the prob These test-bed compound aircraft lems associated with high-speed rotary-wing aircraft.
were modified and tested under contracts by the U.S. Army.
This report presents flight-test results obtained during a program by the National Aeronautics and Space Administration utilizing a hingeless-rotor compound helicopter.
Program support was provided by the U.S. Army. Data a r e presented to indicate the level-flight performance characteristics, speed stability, maneuver stability, and wing- rotor lift sharing in maneuvering flight. Also included are data indicating the rotor rotational-speed control characteristics during maneuvers and during simulated main- rotor power failures.
SYMBOLS longitudinal control position, positive in nose-down direction, degrees B1 number of blades b rotor lift coefficient, cLR ~ T R ~ ( ~ R ) Z Lwb wing-body lift coefficient, 'bvb lift-curve slope for wing-body, a c b v b (cLa)wb aaB C blade chord, feet (meters) auxiliary jet thrust, pounds force (newtons) F N longitudinal cyclic-stick force, pounds force (newtons) FBY acceleration due to gravity, 32.2 ft/sec2 (9.8 m/sec2) g rotor lift, pounds force (newtons) LR wing-body lift, pounds force (newtons) Lwb LR + =wb n aircraft vertical load factor, W
equivalent total horsepower, Pi + FNVTAS, horsepower (kilowatts)
Pe indicated shaft horsepower, horsepower (kilowatts) Pi aircraft roll rate, positive with right roll, degrees/second aircraft pitch rate, positive nose-up, degrees/second free-stream dynamic pressure, pounds force/foot2 (newtons/meterZ) % 3 rotor radius, feet (meters) R wing area, feet2 (meters21 s, calibrated air speed, knots VCAS true airspeed, knots VTAS W aircraft gross weight, pounds force (newtons) boom -indicated angle of attack, angle of fuselage reference line relative @ B to wind, positive nose-up, degrees rotor control-axis angle of attack, positive when tilted rearward, degrees o r @ C as indicated radians aircraft sideslip angle, positive nose left, degrees lateral stick position, positive for right deflection, inches (centimeters) longitudinal stick position, positive f o r rearward deflection, inches (centimeters) blade-root pitch angle, degrees
e
blade -root collective-pitch angle, degrees air density, slugs/foot3 (kilogramslmeter3) P
rotor solidity, bc
U 7rR 52 rotor angular velocity, radians/second I APPARATUS AND TESTS Description of Test Aircraft The test aircraft, shown in figure 1, was a compound helicopter which incorporates a hingeless-rotor system. The aircraft is described in more detail in reference 3. The basic physical characteristics of the test aircraft are presented in table I.
The flight-control systems are basic helicopter-type controls, and there a r e no movable fixed-wing-type control surfaces incorporated. The aircraft is equipped with the standard XH-51A mechanical control gyro. The auxiliary power system required an additional control which is incorporated in the twist grip of the collective-pitch handle.
Because of this modification, the primary power control is installed on a quadrant mounted to the left of the collective-pitch lever.
The cyclic-stick control has an irreversible boost with a longitudinal feel spring (8 lbf/in. (14 N/cm)). A bobweight (7.2 lbf/g unit (32 N/g unit)) w a s also incorporated into Total stick travels were 10 inches (25.4 cm) and 4.625 inches the longitudinal control.
(11.7 cm) for the longitudinal and lateral directions, respectively.
For the test results presented herein, the longitudinal cyclic control was set at 66 percent of the designed stick gearing, and the lateral cyclic control w a s set at 200 per cent of the designed stick gearing. These changes simply alter the pilot's cyclic-stick displacement required to produce a given aircraft response rate. The change in the lon gitudinal system, for example, reduces the response r a t e for a given stick displacement to 66 percent of the r a t e which would be achieved with the standard stick gearing.
Instrumentation tests was installed and calibrated by the The instrumentation utilized during these contractor. Data were recorded on a 50-channel oscillograph and a photo recorder.
Tests The flight -test program consisted of approximately 9 hours of operation including the pilot's familiarization flights. The tests were accomplished in two phases.
Since these tests were not intended to extend the operating envelope of the aircraft, the data obtained were limited to airspeeds up to approximately 190 knots calibrated airspeed and a specified range of rotor loading (i.e., collective-pitch angles).
The flight conditions investigated included level flight throughout the allowed forward-speed range, autorotation entries, maneuver characteristics, cyclic-control response characteristics, and rotor rotational-speed control in maneuvers.
RESULTS AND DISCUSSION The data presented herein include the level-flight performance characteristics, speed stability, and maneuver stability for several airspeeds and also data indicating the lift-sharing characteristics during maneuvering flight. Also included a r e data indicating the rotor rotational-speed control characteristics during maneuvers and during simulated main-rotor power failures.
The majority of the test points were taken with a nominal collective-pitch setting This value represents the recommended pitch setting for compound-mode flight of 3.5'.
Thus, once the airspeed exceeded (i.e., airspeeds above approximately 100 knots).
100 knots, the collective pitch could be set to the desired position of 3.5', and the aircraft could be flown essentially as a fixed-wing aircraft with speed variations being made by throttle control of the auxiliary thrust engine.
Level- Flight Performance The primary level-flight performance characteristics of the test vehicle a r e pre sented in figures 2 to 6. These data were obtained at a density altitude of approximately 5700 feet (1.7 km).
Rotor lift and indicated angle of attack.- The variation of the ratio of rotor lift to gross weight with true airspeed for a range of collective-pitch settings is presented in figure 2. For the recommended compound-mode setting of 3.5', the rotor lift is equiva lent to 57 percent of the g r o s s weight at 110 knots and decreases almost linearly with increasing airspeed. Extrapolation indicates that the rotor would be completely unloaded at approximately 240 knots. Increasing collective pitch, of course, increases the relative rotor loading; however, the maximum airspeed at the higher collective-pitch setting is restricted by an early onset of vibrational problems. Thus, a collective-pitch setting in the range from approximately 3.5O to 4.3O provides the maximum range of airspeed wherein the aircraft can be flown without need for a collective-pitch change. In addition to minimizing the pilot workload, by maintaining constant collective pitch, the trend of decreasing rotor l i f t as airspeed increases is advantageous. As the rotor penetrates a more unfavorable environment at the higher speeds, the gradual unloading of rotor lift tends to eliminate problems associated with rotor stall.
First, as indicated in There are limitations at both ends of the airspeed range.
figure 2, the rotor may be completely unloaded at about 240 knots and would probably Second, produce negative lift above this airspeed, with obvious performance penalties.
with the low collective-pitch setting, the aircraft angle of attack increases rapidly as the For example, the variation of the level-flight airspeed is reduced toward 100 knots.
The lower fuselage angle of attack with t r u e airspeed is presented in figure 3.
collective-pitch setting requires an excessive nose-high angle of attack in order to achieve the required lift on both the wing and rotor. Thus, flight at airspeeds near 100 knots can be accomplished more comfortably by employing a higher collective-pitch setting.
Thrust and power requirements. - The auxiliary thrust and power requirements for
the test aircraft a r e presented in figures 4 to 6. Figure 4 presents the auxiliary thrust requirements for a range of collective-pitch settings. The thrust levels are indicated in t e r m s of an equivalent flat-plate drag a r e a because this parameter reflects the nose-high attitude requirements for the low collective-pitch settings at the lower speeds. In addi tion, the rotor attitude is such that a drag force is produced instead of a propulsive force since the rotor is very close to an autorotative condition at the low collective-pitch set ting. As illustrated in figure 5, the rotor power requirements decrease with decreasing collective pitch; however, the auxiliary jet thrust must be increased to compensate for this decrement. In order to ascertain the total power requirements of the aircraft, an equivalent total horsepower which includes both the rotor-shaft horsepower and the jet thrust has been computed and is presented in figure 6. The data in this figure encom pass all the collective-pitch settings utilized. Within the scatter of the data, it would appear that the total power requirements at a given airspeed a r e the same regardless of the collective pitch selected.
Wing-body l i f t coefficient. - The wing-body lift coefficient is presented in figure 7
as a function of the boom-indicated fuselage angle of attack for the range of test air speeds. These data were obtained in level flight and have been corrected for the jet- reaction effect due to inclination of the jet thrust axis. By using a least-squares curve fit, a lift-curve slope of 0.0606 per degree (3.47 per radian) is indicated.
Control Response The longitudinal and lateral cyclic-stick response characteristics were evaluated for a range of airspeeds. The results a r e presented in figure 8 as a function of the air craft pitch or roll rate per inch (centimeter) of stick deflection. It should be recalled that these tests were performed with the stick gearing set at off-design conditions and that the rotor has a mechanical control gyro which has a significant effect on the response.
The data include the response characteristics at several collective-pitch settings although no significant effect on response is apparent for most of the settings. At the highest collective-pitch setting (00 = 6 O ) where there is a relatively large change in rotor lift, the response about both axes appears to be slightly higher as might be expected; however, since the rotor hub moment is the more significant part of the total rotor moment, the gradient with increasing airspeed is primarily dependent on the increased hub-moment sensitivity. Although the magnitude and gradient with air speed of the longitudinal response sensitivity are low, some difficulty would be expected in achieving compatible response characteristics at both low and high speeds. Limited hover and low-speed qualitative evaluation indicated that the longitudinal response was less than desired.
Stability Characteristics Speed stability.- The speed stability of the test aircraft was evaluated for several t r i m airspeeds. These data, which are presented in figure 9, were obtained by estab lishing a trimmed level-flight condition at a given air speed and making slow variations in airspeed about the t r i m point. A s indicated, the longitudinal stick position 6y has a The slope of the stick position is also slightly unstable slope for all test airspeeds.
slightly unstable about the t r i m point for increased rotor loading at 109 knots (00 = 6 . 8 ' ) .
Although the data are indicative of an instability with speed, the gradient is so small that the pilot's impression was that the aircraft had neutral stability. In view of the fact that these data were obtained at reduced longitudinal stick sensitivity which necessitates larger stick deflections, the gradient of stick position with speed would be reduced as stick sensitivity is increased.
Maneuver stability. - Two techniques were utilized to evaluate the maneuver stability
of the test aircraft. The f i r s t technique employed was the windup turn to obtain the stick force per g unit, and the second technique was the pull-and-hold maneuver normally uti lized for pure helicopters.
The results of the windup turn maneuvers are presented in figure 10 as the variation of the measured longitudinal stick force per unit load factor over the range of test air speeds. Also included a r e the variations in stick sensitivity (g units per inch (centimeter) of stick deflection) and the angle-of-attack sensitivity (g units per radian change in fuse lage angle of attack).
In all cases, the aircraft exhibited positive maneuver stability (that is, a positive stick displacement and force gradient); however, the pilot felt that the force gradient was high at the lower speeds. Since the force gradient results from an artificial feel system which is dependent on stick displacement and load factor, some latitude in providing a suitable gradient was available. The stick force gradient can also be determined with the following expression: .
I
The parameter dn/ddy is presented in figure 10 for a control gearing of 66 per cent of the designed gearing. Thus, increasing the control gearing or decreasing the feel-spring constant would produce a lower stick force gradient. At the higher speeds, the pilot felt that the combination of stick force gradient and stick sensitivity were at a satisfactory level. It should be pointed out, however, that no attempt was made to eval uate other combinations of artificial force gradient.
The last parameter dn/daB presented in figure 10 is a measure of the overall aircraft sensitivity in maneuvers. As a result of the influence of the rotor it will be noted that the sensitivity dn/daB increases at a r a t e considerably less than the velocity squared of a fixed-wing aircraft.
The dashed-line curve indicates calculated values based on the rotor lift derivatives given in reference 4 and the measured lift-curve slope of the wing-body combination. For this calculation, it w a s assumed that no change in rotor cyclic pitch w a s introduced; hence, the calculated curve is a measure of the effec tive controls-fixed sensitivity of the aircraft. The measured data, of course, include the effect of the rotor control variations required to perform the maneuvers. The equation used for the calculation is as follows: where dBl/daB is assumed to be zero.
The measured sensitivity appears to be higher than the controls-fixed calculation at airspeeds below 155 knots and is lower than the calculation above 155 knots. As will be illustrated subsequently, these results a r e compatible since the measured values of dBl/daB a r e negative at the lower speeds and positive at the higher speeds. Therefore, as noted in equation (2), a negative value of dBl/daB will increase the total aircraft sensitivity dn/daB; whereas, a positive value will decrease the calculated sensitivity.
The reversal in sign of the t e r m dBl/daB is indicative of a change in the level of angle-of-attack stability of the aircraft. When dBl/daB is negative, the aircraft is stable; whereas, a positive value indicates an unstable system. Even though the stick- position gradient is positive (fig. 10) throughout the test airspeed range, the actual con trol position, as commanded by the mechanical control gyro on this aircraft, r e v e r s e s at the higher speeds.
direction in order to provide positive angle-of -attack stability The reversal of control position is quite evident in the pull-and-hold maneuver illustrated in figure 11. For the condition presented, the aircraft response to a 1-inch rearward (2.54 cm) cyclic input is indicative of a stable system. That is, both the rate and normal acceleration a r e concave downward in l e s s than 2 seconds, and the stick displacement (and, consequently, the stick force) remains rearward. (See ref. 5.) The blade pitch angle, however, is indicative of a different trend. The cyclic amplitude is approximately 2' (i.e., I31 = 2') nose-down in level flight, which is consistent with the forward stick position. After the longitudinal stick position is displaced rearward, the blade cyclic-pitch amplitude decreases as expected; and then with constant stick position, the amplitude increases beyond the original t r i m (Le., B1 > 2'). The reversal in blade cyclic pitch relative to that commanded by the stick position is introduced by the mechan ical control gyro in providing apparent maneuver stability to the pilot. This reversal in blade cyclic pitch during maneuvers also has a favorable effect on the rotor loading.
Wing-Rotor Load Sharing in Maneuvers Measured rotor-lift sensitivity. - Of particular importance with regard to flight in the compound mode is the relative load sharing between the wing and the rotor during maneuvers. Windup turns were executed in order to establish the rotor-lift variation with load factor for several airspeeds. The results are presented in figure 12. The data presented were taken a t a nominal collective-pitch setting of 3.5'. The variation in rotor lift at 1.Og merely reflects the level-flight lift variation previously indicated (fig. 2). The data indicate that the rotor is providing a smaller increment of lift for a given load factor at the higher airspeeds.
In order to illustrate this trend more clearly, the rate of change of the rotor loading -- with load factor d(LR'W) was determined and is plotted as a function of airspeed in fig dn u r e 13. Since the rotor loading with load factor was essentially independent of collective pitch, figure 13 includes data applicable to all tested collective-pitch values. The curve illustrates the effective decrease in the rotor-lift sensitivity with increasing airspeed.
F o r example, in the turning maneuver the rotor provides approximately 73 percent of the incremental lift at 120 knots, but only 44 percent of the incremental lift at 210 knots. The reduction in lift sensitivity with speed is very beneficial since the rotor produces lower lift increments during maneuvers as it penetrates the more unfavorable environment at higher speeds.
Calculated rotor sensitivity (controls fixed). - In order to illustrate the unusual -
-- - -_
rotor-loading trend of the test aircraft, a calculated curve based on the theoretical rotor lift derivative is included in figure 13. The equation used is as follows: daC/dn is assumed to be equal to the inverse of the measured parameter where dn/dag (fig. 10). Thus the calculation represents the expected rotor-lift sensitivity The measured with blade cyclic controls fixed. The difference in trends is obvious.
I
curve, of course, was obtained with cyclic-control inputs, and thus the change in rotor angle of attack with load factor would differ from the fuselage angle of attack aB used.
Calculated rotor sensitivity (including control displacement). - The actual change in - -
rotor angle of attack with load factor may be expressed as follows: It should be noted that stable maneuver stability requires a negative sign for dBl/dn.
The negative sign, however, makes the parameter daC/dn larger than daB/dn and would increase the rotor -loading sensitivity. Unstable maneuver stability, on the other hand, requires a positive sign for dBl/dn, thus decreasing the rotor -loading sensitivity.
It would appear from figure 13, therefore, that above approximately 150 knots the aircraft has negative angle-of -attack stability.
Although it was indicated in figure 10 that the aircraft had positive maneuver sta bility as apparent to the pilot (stick position and force) over the test airspeed range, a n analysis of these data indicates that there is considerable cyclic -pitch feedback occurring during maneuvers which is produced by the mechanical control gyro. For example, fig u r e 14 illustrates the measured variation of the longitudinal cyclic-pitch increment AB1 with load factor for several airspeeds. The increment AB1 is the difference between the longitudinal cyclic pitch in level flight and the value in the turn. It is actually a com bination of the pilot input and the control-gyro feedback. It should be recalled (fig. 10) that in all cases a rearward stick displacement was required to maintain a given load factor; however, the steady-state longitudinal cyclic pitch is shown to be in the opposite direction at the airspeeds above approximately 150 knots. In other words, the feedback required a t higher speeds is large enough to wash out the pilot's rearward cyclic input (i.e., a negative B1 increment) and actually produce a positive cyclic-pitch increment.
Thus, as speed increases, the effective rotor angle-of -attack change in maneuvers This characteristic, in turn, reduces the rotor-lift becomes progressively smaller.
sensitivity in maneuvers as airspeed is increased.
As an illustration of the effect on the lift sensitivity of including the actual rotor cyclic control, the calculated curve presented in figure 13 has been recomputed to include The corrected points are presented in figure 15.
the cyclic t e r m s shown in figure 14.
Although the 210-knot data point is some The improvement in correlation is apparent.
what high, the overall trend of sensitivity is well defined.
An alternate method f o r predicting load sharing is to use the lift-curve slope for The curve in figure 15 labeled "calculated using " was computed the wing-body.
( ' La)wb
with the following equation: = 3.47 per radian. (See fig. 7.)
where wb The parameter dag/dn is the measured value obtained from figure 10 (the inverse of dn/dag). It should be noted that the lift-curve slope used w a s obtained from level-flight data and therefore does not reflect the effects of pitch rate. Pitch rate would be expected to increase the effective wing-body loading contribution due to the horizontal tail and thus improve the correlation between the two curves. Nevertheless, the trend of the measured rotor loading is well defined.
Although the trend of decreasing rotor-lift sensitivity with increasing airspeed is advantageous with regard to avoidance of rotor -stall problems, it should be emphasized that the decreasing sensitivity occurs as a result of decreasing aircraft stability and a n unstable rotor-fuselage configuration a t the higher speeds. In this particular aircraft, however, the control gyro provides the stabilizing inputs required without pilot action.
Thus, even though the pilot's cues (i.e., stick position and force) are indicative of appar ent stability, the actual control position is not. Without the gyro, the maneuvering char acteristics would, of course, be the same except that the pilot would have to provide the stabilizing inputs by moving the stick forward. In either case, the favorable rotor-loading trends result in reduced forward-control capability and, with the gyro in the system, the pilot is unaware of the remaining control margins. Although not encountered during the program, there may be combinations of airspeed and load factor that would utilize the maximum available nose-down cyclic pitch. Once this condition is reached, the aircraft would be divergent with a further increase in the angle of attack.
Rotor Rotational - Speed Control Rotor rotational-speed control is important with regard to both the power -off auto- rotational characteristics and the maneuver overspeed characteristics. Since both of these characteristics are related to the load factor required to autorotate the rotor in a banked turn, criteria which define these load factors are adequate for establishing the maneuver overspeed trends as w e l l as the power -off autorotational requirements. Tests were accomplished to establish the rotor rotationaLspeed (rpm) variation with load factor The procedure was to establish a t r i m level-flight condition for the f o r the aircraft.
desired configuration and then to reduce main-rotor power to flight idle while entering a descending banked turn at constant airspeed and jet thrust. The rotor speed w a s allowed to drop to 90 percent of the design rpm. When a steady load factor for maintaining 90 percent rpm was established, the load factor was gradually increased in order to increase the rotor rpm.
Samples of the resulting data a r e presented in figure 16 for two airspeeds. The boundary lines indicate the combinations of rpm and aircraft load factor that will produce autorotation: that is, the shaft power is zero. The a r e a to the left of each boundary represents the envelope wherein shaft power must be supplied to drive the rotor. Con versely, to the right of the boundary, the rotor extracts energy over and above that required to autorotate and would speed up in o r d e r to reestablish equilibrium on the autorotation boundary.
From the standpoint of maintaining rotor rpm in the event of a main-rotor power failure, the boundary represents the load factor necessary to prevent an underspeed con dition, assuming no other corrective action is taken. For example, at 115 knots C a l i brated airspeed, the rotor would stabilize at 100 percent rpm if a load factor of approxi mately 1.3g w a s maintained. At 160 knots, the load factor for 100 percent rpm has increased to 1.8g.
In t e r m s of rotor overspeed, the same data may be interpreted as a maneuver restriction in powered flight. If at a constant airspeed the load factor is increased beyond that required to autorotate the rotor, the rpm will increase from the initial set ting. Figure 17 illustrates typical variations of power-on rpm with load factor for two different initial rotor speeds at 115 knots calibrated airspeed. The initial r i s e in rotor rpm as load factor increases is a function of the power governing loop. As the power demand is decreased, the governor reduces the supplied power and, therefore, the rpm remains essentially constant. However, as the load factor increases further, the shaft power required reaches z e r o (on the autorotation boundary) and the rpm r i s e s along the boundary line as indicated. For the case illustrated, a steady load factor of 1.6g would produce a final rotor rpm in excess of 110 percent regardless of the initial governed rpm In order to illustrate the effectiveness of changes in aircraft configuration, a sum mary plot is presented in figure 18. Included in the figure a r e the effect of increasing the collective-pitch setting to a value above the normal compound mode of 3.5' and the effect of deploying the wing spoilers at the normal collective position. The boundary lines indicate the load-factor requirements to maintain a specified rpm as a function of the airspeed. The upper boundary (110 percent) can be associated with the power-on maneuver overspeed since any combination of airspeed and load factor which is above the boundary would drive the rotor rpm to values greater than 110 percent. For example, the data in figure 18(b) indicate that for a 2g maneuver the rotor speed would exceed 110 percent for airspeeds up to approximately 150 knots calibrated airspeed. The lower boundary, on the other hand, is an indication of the load factor which must be achieved in order to stabilize the power-off rotor rpm at 90 percent.
Changes in configuration can be accomplished in order to shift the boundaries in the desired direction. For example, figure 18(a) shows the effect of an increase in collective pitch which effectively increases the maneuver overspeed boundary. Fig u r e 18(c) shows the effect of application of wing spoilers as a means of lowering the These changes in configuration indicate that boundary for the power -off autorotation.
the boundaries can be shifted with appropriate pilot action; however, this requires the pilot to monitor rotor rpm in order to prevent rotor overspeeds in maneuvers.
Autorotational Characteristics
Rotor rotational-speed decay rate. - Tests were performed to establish the rotor
rpm decay r a t e following a loss of the primary power supply. The data, which were obtained at fixed collective pitch for several airspeeds, are presented in figure 19. The relatively low decay rates established result primarily from the low horsepower require As might be expected, the ments of the rotor over the test airspeed range. (See fig. 5.)
trends of the decay r a t e s reflect the changes in horsepower requirements shown in fig ure 5. Consequently, as the power required increases at the higher forward speeds, the The decay rates, however, a r e lower than those gener rotor rpm decay r a t e also rises.
ally demonstrated by a pure helicopter which, of course, operates with higher rotor power requirements.
The benefits associated with the low decay r a t e s a r e offset at the higher airspeeds by the increase in the load-factor requirements f o r autorotating the rotor.
(See, for example, fig. 18.) The rising decay r a t e and increasing load-factor require ments necessitate p r o q p t action by the pilot in order to make an autorotative entry at the higher speeds.
Autorotative entries. - Autorotative entries following a simulated main-rotor power failure were made for a range of t r i m airspeeds from approximately 110 to 215 knots true airspeed. The same general maneuver w a s used to a r r e s t the rotor rpm decay.
That is, the pilot initiated a windup turn in order to place the rotor into an autorotative condition. In addition to performing this maneuver, the pilot had recourse to additional actions in order to a r r e s t the rotor rpm decay. These included application of wing lift spoilers, reduction of auxiliary thrust, and a reduction of rotor collective pitch if necessary.
A sample autorotative entry is presented in figure 20. The simulated main-rotor power failure was initiated at a calibrated airspeed of 174 knots. The rotor speed was allowed to decay to 95 percent prior to taking any corrective action. For this entry, the pilot made an abrupt auxiliary-thrust reduction at 3.6 seconds (2.6 seconds after main- rotor power reduction) and deployed the spoilers at 5 seconds. Both of these actions produce a nose-down t r i m change, and the pilot reported that the t r i m shift was somewhat distressing with this sequence of abrupt action. All other entries were performed by using a more gradual reduction in auxiliary thrust; however, this abrupt maneuver s e r v e s t o emphasize the necessity of minimizing the t r i m shifts associated with corrective actions in an autorotative entry.
Throughout the airspeed range of the test, the rotor speed could be allowed to drop to 95 percent, and then with corrective action the r p m was maintained above 90 percent.
The allowable delay time was, of course, decreasing as indicated by the rising decay rates in figure 19. Thus, at the higher speed relatively prompt action would be required.
CONCLUDING REMARKS The flight-test results presented and discussed herein have indicated several trends which are of interest concerning both the performance and the flying qualities of com pound helicopters. Specifically, the inherent reduction in rotor lift as level-flight air - speed is increased is desirable since no pilot action is required, and the reduced t r i m lift provides a margin between t r i m lift and the lifting capability of the rotor which may be utilized in maneuvers.
The trend of decreasing rotor-lift sensitivity in maneuvers with increasing airspeed is also advantageous with regard to avoidance of rotor-stall problems; however, it should as a result of decreasing be emphasized that in this case the decreasing sensitivity occurs aircraft stability and an unstable rotor -fuselage configuration at the higher speeds.
Although these lift-sharing trends contributed favorably to the piloting task in the compound mode, the rotor over speed tendencies could require constant pilot attention during maneuvering flight.
High-speed autorotative entries could be made without undue pilot effort as a result of the low power requirements of the rotor which produced relatively low rotor rotational- speed decay rates. Adverse t r i m changes associated with any corrective actions should be minimized so that positive pilot response does not introduce undesirable disturbances.
Langley Research Center, National Aeronautics and Space Administration, Langley Station, Hampton, Va., October 27, 1969.
RE FERENCE S Use of Thrust and Lift Augmentation for Increasing Heli 1. Robinson, Donald W., Jr.: Pap. No. 63-94, Inst. Aerosp. Sci., Jan. 1963.
copter Operating Speed.
High-Performance Helicopter Program.
2. Van Wyckhouse, J. F.; and Cresap,, W. L.: TRECOM Tech. Rep. 64-61, U.S. Army, Oct. 1964.
Summary Report, Phase 11.
3. Wyrick, Donald R.: Extension of the High-speed Flight Envelope of the XH-51A Compound Helicopter. USAAVLABS Tech. Rep. 65-71, U.S. Army, Nov. 1965.
(Available from DDC as AD 627 372.)
Stability and Control Handbook for 4. Kisielowski, E.; Perlmutter, A. A.; and Tang, J.: Helicopters. USAAVLABS Tech. Rep. 67-63, U.S. Army, Aug. 1967. (Available from DDC as AD 662 259.)
Helicopter Flying and Ground Handling Qualities; General Requirements for.
5. Anon.: Mil. Specif. MIL-H-8501A, Sept. 7, 1961, Amendment I, Apr. 3, 1962.
I .... . . . . . . . . . . . . . . . . . . . . -- ........_..._....- ....-.- ....
__ TABLE 1.- PHYSICAL CHARACTERISTICS OF TEST AIRCRAFT General :
Nominal take-off weight. lbf (N) . . . . . . . . . . . . . . . . . . . . . 5165 (22 974)
Longitudinal center of gravity. forward of rotor mast. in . (cm) . . . . 0.30 (0.76)
Lateral center of gravity. left of center. in . (cm) . . . . . . . . . . . . 3.81 (9.68)
Overall length. f t (m) . . . . . . . . . . . . . . . . . . . . . . . . . . 42.58 (12.98)
Area ratio (wing t o rotor) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.0728 Main rotor:
Diameter. f t (m) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 (10.67)
Blade chord (constant root to tip). in . (cm) . . . . . . . . . . . . . . . 13.5 (34.29)
Solidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0818
Blade airfoil section . . . . . . . . . . . . . . . . . . . . . . . . Modified NACA 0012
Normal operating rotational speed. r p m . . . . . . . . . . . . . . . . . . . . . . . 355
Blade twist (root to tip). deg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5
Shaft incidence. forward. deg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tail rotor:
Diameter. in . (cm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 (182.88)
Blade chord (constant root to tip). in .
(cm) . . . . . . . . . . . . . . . 8.5 (21.59)
Solidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1503
Blade airfoil section . . . . . . . . . . . . . . . . . . . . . . . . . . . NACA 0012
Blade twist. deg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4.35 Wing:
Span (nominal). ft (m) . . . . . . . . . . . . . . . . . . . . . . . . . . 16.83 (5.13)
Taper ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5
Area (including carry-through). f t 2 (m2) . . . . . . . . . . . . . . . . . . . 70 (6.5)
Aspect ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.05 Airfoil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NACA 23012
Incidence (fixed). relative to fuselage reference line. deg . . . . . . . . . . . . . -0.9
Powerplants:
Primary type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Turboshaft
Maximum shaft power (take-off) at sea level. hp (kW) . . . . . . . . . . 500 (373)
Military shaft power (30-min limit) at sea level. hp (kW) . . . . . . . 450 (335.7)
Auxiliary type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Turbojet
Military thrust at 200 knots at sea level. lbf (N) . . . . . . . . . . 2490 (11 075.5)
L-69-5102 Figure 1 . - Test aircraft.
L O Nominal eo, deg p .8 3 . 5 OI: A I -- - 4.3 -- 0- .- 5.2 c e 6.8 .6 c c D .- B v) v) .
. 4
c P
-
. - I L - s . 2 I Y
0 ! U L - - L A _ > . _ -
1 0 0 120 140 160 180 200 220 240 True airspeed. knots Figure 2.- Variation of level-flight rotor l i f t w i t h airspeed.
\
- Nominal eo, 3.5 -- -- 4.3 5.2 8 - 6.8 c
0 I-- . L -1. I
L- - -1 100 1 2 0 140 160 180 200 220 True airspeed, knots F i g u r e 3.- Variation of level-flight angle of attack w i t h airspeed.
-
2 5 Nominal e , , , deg 3.5 - - - _ - 4.3 -- 5 . 2 2 0
_ - - 6.8
2 0 L 5 - cv E cvc @ z
- U
, = 12 L O .5 I . I I. -. .L.-. ...-. I ~ .... I I o 0 .
120 140 160 180 200 220 240 True airspeed, knots F i g u r e 4.- Variation of level-flight a u x i l i a r y t h r u s t (expressed as a n equivalent flat-plate drag area) w i t h airspeed.
-
Nominal eo, deg CL -c 3.5 _ _ - - - 4.3 - 2 3 0 0 --- 5 . 2
-
200 f --- L ' 6. 8 W
H
zl n a= m
-
;r 200 .I= m v) .I= v) U W c
- - _ _ _ - - -
U 100 8 W .- c m -0 t :
---
-
-
g 100
t :
-
. L I - 0 I -, ' - F i g u r e 5.- Variation of level-flight main-rotor power w i t h airspeed.
-
- lo00 n c
-
800 600 L ‘ i a , a ,
z
a n Q) a , ul L - A l l measured collective- 2= .K p i t c h settings - 4 0 0 t u m c c c c c c
-
c 5 400 a , - - m > F .- .- =I =i ET w 200 y” -
I I I - 1 I - I I
0 1 - 0 True airspeed, knots F i g u r e 6.- Variation of level-flight equivalent total horsepower w i t h airspeed f o r a l l measured collective-pitch settings.
I 0 2 4 6 8 10 12 Boom-indicated angle o f attack, aB, deg Figure 7.- Variation of wing-body lift coefficient w i t h boom-indicated angle of attack f o r a l l test airspeeds.
- 8
@ c
E Q - 6 % W
e
m W -0 W v) I= - 4 3 00, deg W L
-
0 3.5 m L a J 17 4. 3 + .!I A 5. 2
0 6.0
1 - -I I - 120 140 160 180 200 220 240 True airspeed, knots F i g u r e 8.- A i r c r a f t response to cyclic-stick input.
I
t s 8 --_I_ 4 ' Rearward 1 Reference stable slope
1 1
r
- - I 1 - - - --.I 1 I I __ - - - __ _ _
Forward -2 1
80 100 120 140 160 180 200 220 Ca I ibrated airspeed, knots F i g u r e 9.- Variation of rotor lift, angle of attack, a n d longitudinal stick position w i t h airspeed, I= v u 0 ‘ / /
16 i /
.
.c-’ Measured f’ I . . I I. 1 100 120 140 160 180 200 220 240 True airspeed, knots F i g u r e 10.- V a r i a t i o n of airspeed m a n e u v e r i n g sensitivity w i t h airspeed ( w i n d u p turn).
d 5000 L E 3 -
3000 -
J v) c 5 1 (5, r- I I I I Blade zero a z i m u t h position marker
i
1 2 3 4 Time, sec F i g u r e 11.- Time history of longitudinal p u l l - a n d - h o l d maneuver. VCAS = 170 knots.
.24 I 1
0 I
1 . 2 1.4 1.6 1 . 8 2 0 1 . 0 Load factor, n F i g u r e 12.- V a r i a t i o n of rotor l i f t w i t h load factor for several airspeeds. O0 = 3.5O; w i n d u p turn.
I I ! -1 ~ I I !
160 180 200 220 240 120 140 True airspeed, knots F i g u r e 13.- Effect of airspeed on rotor-lift sensitivity in maneuvering flight.
VTAS = 210 knots
- I
- 3 - l I I I ~~ I . .. 1 L 1 . 0 1 . 2 1 . 4 1 . 6 1 . 8 20 Load factor, g u n i t s F i g u r e 14.- V a r i a t i o n of l o n g i t u d i n a l cyclic-pitch i n c r e m e n t w i t h load factor.
,-Calculated u s i n g (C 1 La wb
/
/ / \ A l l measured collective c
-
-c D Calculated (rotor control fixed) 0 Calculated i n c l u d i n g rotor control i n p u t I I I .. I 1 . .I - I I 100 1 2 0 1 4 0 160 1 8 0 200 220 240 True airspeed, knots F i g u r e 19.- Comparison of measured a n d calculated r o t o r - l i f t sensitivity.
I
L O L 2 L 4 L 6 1 . 8 20
Load factor, g units F i g u r e 16.- Variation of power-off rotor rotational speed w i t h load factor.
/
110 r
VCAS =I I5 knots Initial rpm = 100% I I __ __ .. - L A
1. 0 L 2 L 4 1. 6 1.8 2 0
Load factor, g units F i g u r e 17.- Variation of power-on rotor rotational speed w i t h load factor.
rpm = 110% 100 % L 4 -a m
L 2 I I /
L O 1 I 1 - !
2 0 (c) eo = 3.5O w i t h spoilers.
1.8
.-
c c n L 6
-
L + g L 4 \c -u 1.2 1.0 110 120 130 140 150 160 170 180 Calibrated airspeed, knots F i g u r e 18.- Effect of a i r c r a f t configuration o n rotor steady-state autorotative boundaries.
Nominal eo, deg
__o__ 3.5
- 4- - 6. 8
120 140 160 180 200 220 240 100 T r u e airspeed, knots F i g u r e 19.- Rotor rotational-speed decay rate following m a i n - r o t o r t h r o t t l e chop (spoilers n o t applied).
Main-rotor Power Aux.power c u t cut Spoilers o u t Spoilers in
- - I I I I
I
- I
>
120 -- 160 j
- 15000
z
-
h
0 2 4 6 8 10 12 14
Time, sec F i g u r e 20.- Time history of autorotative entry.
Main-rotor Power Aux-power CT, aJ '0 d 0 2 4 6 8 10 12 14 Time, sec Figure 20.- Concluded.
AERONAUTICS NATIONAL AND SPACE ADMINISTRATION WASHINGTON, D. C. 20546 FIRST CLASS MAIL OFFICIAL BUSINESS POSTAGE AND FEES PAID NATIONAL AERONAUTICS A SPACE ADMINISTRATION “The ncr.oizai/ticnl nizd spnce nctiz’ities of the United Stntes shall be condiicted so as t o contribzrte . . . t o the expnitsioa of hiliiinn Riaowl edge of phenoiiiean in the nluiosphere nnd spnce. The Adniinistrntioiz .thrill proside for the wideJt pmctic.?ble nizd npproprinte disseiizinntion of infori)intion concernilzg its nctizities nizd the residlts thereof.” -NATIONAL AERONAUTICS AND SPACE ACT OF 1958
NASA SCIENTIFIC AND TECHNICAL PUBLICATIONS
TECHNICAL REPORTS: Scientific and TECHNICAL TRANSLATIONS: Information technical information considered important, published in a foreign language considered complete, and a lasting contribution to existing to merit NASA distribution in English.
knowledge.
SPECIAL PUBLICATIONS: Information TECHNICAL NOTES: Information less broad derived from or of value to NASA activities.
in scope but nevertheless of importance as a Publications include conference proceedings, contribution to existing knowledge. monographs, data compilations, handbooks, sourcebooks, and special bibliographies.
TECHNICAL MEMORANDUMS: Information receiving limited distribution TECHNOLOGY UTILIZATION because of preliminary data, security classifica PUBLICATIONS: Information on technology tion. or other reasons. used by NASA that may be of particular interest in commercial and other non-aerospace CONTRACTOR REPORTS: Scientific and applicatioiv. Publications include Tech Briefs, technical information generated under a NASA Tdinology Utilization Reports and Notes, contract or grant and considered an important and Technology Surveys.
contribu tion to existing knowledge.
Details on the availability of these publications may be obtained from: SCIENTIFIC AND TECHNICAL INFORMATION DIVISION NATIONAL AERONAUTICS AND SPACE ADMINISTRATION Washington, D.C. 20546