PREPURCHASE SURVEY CHECKLIST

Look for loose, bent, collapsed or missing clamps at front and back of muffler Check exhaust manifold and tailpipe for corrosion Check for worn or missing rubber grommets on tailpipe hangers at firewall Check angles on firewall for wear and looseness Check for missing, bent or distorted muffler flame cones Check muffler exterior for dents, heat warp, holes or cracks Exhaust System Checked Notes 2 Cowl Flaps Checked Notes Check that cowl flaps fit well and do not contact firewall(s) or rub cowling(s) Check cowl flaps for excessive looseness, wear, cracks or breaks Check for damage to the cowl flap hinge lines (BARONS AND TRAVEL AIRS): Check for rubbing between cowl flaps and breather lines (MANUAL COWL FLAPS): Check smooth operation of cockpit cowl flap control (Bonanza/Debonair: Binding may indicate friction between cowl flap and nose wheel tubes. Friction here may lead to the inability to extend the nose wheel) (ELECTRIC COWL FLAPS): Verify operation of cowl flap motors and actuators Cowling and Cowl Doors Checked Notes Check doors for proper fit all around, and any damage due to rubbing against engine components or baffling, or at the front of the cowling Inspect cowling hinge area for damage from being blown open beyond limits Check general condition of cowl doors and nosebowl (95s: fiberglass nosebowls) Verify all cowling latches/Dzus fasteners are in place and working properly Propeller(s) Checked Notes Check spinner(s) for cracks, dents or damage (FAA does not permit chromed spinners) Check spinner bulkhead(s)/backplate(s) for cracks, dents or damage (ELECTROTHERMAL PROPELLER): Check condition of wiring, brush blocks, slip rings and hold-down boots (ALCOHOL PROPELLER): Check condition of plumbing, slinger ring(s) and rubber prop leading edge boots Check propeller blades for security, cracking, nicks or other damage Nose Landing Gear Checked Notes Check for leaks, visible corrosion or rust on the nose landing gear strut Check for nose tire cupping, cracks in the tire, excessively worn tread, flat spots or chord showing Check for pitting or corrosion on the chromed part of the strut Check for looseness in the nose strut mounting, piston or barrel Check shimmy damper for security and inspect for bends or leaks Check tow pin area for damage Check for any cracks, dents, bends or corrosion of the wheel well sheet metal Look for bent, loose or missing rivets or bolts Check condition of boots for nosewheel steering and retraction Check for bent nose wheel steering mechanism or gear door pushrods Check nose gear doors and hinges for bends, wrinkles or excessive wear Check for bends in the nose gear door pick up arm Check for grooved, bent or missing nose gear pickup pin on V-brace Main Landing Gear (check both gear legs and wells) Checked Notes Check for tire cupping, cracks in tires, excessively worn tread, flat spots or chord showing Check for grooves in brake discs and the condition of brake pads Look for hard, stiff, kinked or leaking brake hoses Check for security of the outer main gear doors, and for cracks or loose nuts or rivets at the strut connections and door hinges Check for rusted, pitted or worn areas on the chromed part of the piston 3 Main Landing Gear (check both gear legs and wells) (continued) Checked Notes Look for fluid or other signs of strut leaks Check for any looseness of the gear on its mounts Look for bends, dents, or looseness in surfaces, linkages, arms and brackets Check for close fit and any fraying of uplock cable at uplock roller end Check for evidence of gear rubbing on doors or wheel well Check for rust on the springs associated with the gear uplock mechanism Check uplock roller for freedom to roll Check that inner gear doors retract fully against underside of the wing Retraction Tests Checked Notes Conduct a full gear retraction test Check gear rigging tolerances, including down tensions, free play in the gear box, uplock clearance and any sign of bent extension arms Check gear transit speed (14V 11-13 seconds, 28V 4-8 seconds) Check for looseness in lift leg joints or pivots when gear is at mid-travel point Check for looseness in nose gear rod ends and actuator arm when gear is at mid-travel point Wings Checked Notes Sight across the top and bottom of the wing, checking for dents, wrinkles or paint blistering (Paint blistering may indicate corrosion of wing skins, spars or other internal structure) Check for ground-down rivet heads (Flattened rivets may indicate damage from sanding if the airplane was not fully stripped before repainting) Check that installed wingtip is correct for the model of airplane, or approved as indicated in the airframe log Check tip tanks, if installed, for dents, signs of leaks, delamination of fiberglass, proper fit and condition of fuel caps, proper venting, and opaqueness of visual fuel level indicator windows Inspect ailerons for dents, wrinkles, pinholes, corrosion "blistering," or missing or touched-up paint that might indicate damage or corrosion Check aileron attach screws for security and any corrosion Check aileron is mounted properly (stainless steel screws are not approved) Look for paint overspray in the aileron gaps, or rough or missing paint on the aileron leading edges (Such may indicate ailerons were not removed for balancing) Check aileron trim connections, and that trim is flush with aileron when cockpit indicator indicates "zero" or "neutral" (left only; 95, all Baron, A/B36 1984 and after) With flaps extended, check signs of contact or damage on flap leading edge Check attach bolt "bathtub" fittings for corrosion, standing water or evidence of past standing water, paint stripper, or rusty or corroded wing attach bolts Check bathtub fittings for correct cover and cover attachment Check drain holes under wings beneath bathtub fittings for obstructions Check for evidence of fuel leaks on the top and bottom of wing Check for proper length and slant of fuel vents, and broken or missing vent lines (33, 35, 36 [except 36TC]: Fuel vents must be at least 13 ⁄4 inches below wing, canted forward 10 degrees with 45-degree scarf pointed forward) Crosscheck serial numbers from fuselage, ailerons, flaps and logbooks. Differing serial numbers may indicate replacement due to prior damage. 4 Tail Checked Notes Check fuselage in tail area for any wrinkles, dents, bends, loose rivets, corrosion or other damage Check tail tie-down area for evidence the airplane has been pulled by tie-down ring with excessive force Check all fixed surfaces for corrosion, pinholes, cracks, wrinkles, dents or other damage Look for paint overspray inside elevator/ruddervator/rudder wells, or rough or missing paint on control surface leading edges (Such may indicate controls were not removed for balancing) Check pitch trim tabs, pushrods and hinges for proper mounting and security • "Straight" 35,Travel Airs and Barons have no camber to the trim tabs • A35 - G35 have cambered trim tab with contour on the bottom • H35-V35B, all 33 and 36 have cambered trim tab with contour on top Check pitch and (95, all Barons) rudder trim tab is flush with control surface when cockpit indicator is in the "zero" or "neutral" position Check for unpainted, bent, wrinkled, pinholed, creased or corroded surfaces Check control surface security and condition of hinges Check for excessive play at bearings or rod ends Check control horns for looseness, corrosion or bends (33, 36, 95, ALL BARONS): Look for looseness or movement near rudder attach points Check fixed stabilizers for security, and listen for unusual noises when fixed surfaces are pushed up and down Cabin Area Checked Notes Check for crazed or cracked windows, or windows turning bluish-white in color Look for cracked, broken, discolored or distorted window moldings Check for proper mounting and hardware if windows/doors have been replaced Check fit of forward door, and that hinges do not move when door is moved up and down Check smooth operation of door, and proper operation of door hold-open rod Check operation and security of rear and/or cargo doors, and (95, all Barons) nose baggage door Inspect forward door hinge plates for signs of overextension Look for signs of interior leaks around door and window frame seals Check cabin sidewalls for corrosion under windows, doors, pilot's storm window Check for proper operation of openable windows Check proper operation and then security of emergency exits Check proper installation and operation of seat belts and shoulder harnesses Check proper installation and operation of seats and adjustment mechanisms Check that manual landing gear hand crank is accessible, snaps into cranking position, and restows properly Check that fuel selector valve(s) move easily between all positions including "off" and (95, all Barons) "crossfeed" • Check proper operation of "off" position safety stops" • Travel Air and Model 55 Barons prior to TC-1608 have a mechanical stop that prevents simultaneous selection of "crossfeed" on both engines" While Engine is Warm (May follow flight survey) Checked Notes Conduct borescope check of all cylinders Conduct differential compression check of all cylinders Inspect oil screens/filters for metal or other contamination 5 III. Flight Survey After other surveys complete, discrepancies resolved and airplane deemed airworthy If possible, bring the survey mechanic along on a flight evaluation. If mechanic is not available, bring a knowledgeable observer to record data and assist with traffic avoidance and flight safety. Conduct your survey flight in day, VFR conditions in the immediate vicinity of the airport. Conduct all phases of your survey flight using checklists from the Pilots Operating Handbook/Flight Manual or other Beech-savvy source. Flight Survey Checked Notes Check manifold pressure gauge(s) for ambient pressure indication before start Check all instruments against tolerance for IFR flight after start/during taxi Flight Survey (continued) Checked Notes Functionally check the autopilot system and all methods of disconnect (See POH supplement for autopilot preflight checks and disconnect procedures) Check operation of flaps, preselects and indicating systems were installed Confirm expected manifold pressure and rpm at full throttle at takeoff (MP as per POH/supplement for turbocharged engines; approx. 1" < ambient normally aspirated Check fuel flow is at or above redline at takeoff power (reduce 1.5 gph per 2,000 feet above sea level for normally aspirated engines) IF EQUIPPED WITH FUNCTIONING AUTOPILOT, RECOMMEND ENGAGING AUTOPILOT DURING FUNCTIONAL CHECKS Complete all operations through level-off at a safe altitude in cruise configuration If possible, check tachometer indication using hand-held tach checking device (NORMALLY ASPIRATED): Check manifold pressure at full throttle against expectations from POH for the altitude and propeller speed (TURBOCHARGED): Check for no MP "drift" with changes in altitude and/or propeller speed below critical altitude Compute True Air Speed and compare to POH expectations Using a "flow pattern" across the cockpit (for instance, from left to right), operationally check all instruments, avionics and indicators. Check magnetic compass for proper fluid fill and operation. Turn on and off all switches (unless doing so presents a safety hazard) to check equipment Check for false StormScope ™ /StrikeFinder™ indications (if installed; false plotsmay indicate poorly grounded electrical equipment) Conduct VOR check and compare to 30-day VOR check log Slow (as necessary) to or below landing gear extension speed and cycle the landing gear. Time the gear cycle; check electrical indications and the landing gear position indicators (14V: 7-11 one-way cycling time. 28V: 4-8 seconds) (IF AIRCRAFT AND GROUND EQUIPMENT PERMITS): Fly a coupled ILS approach to test both the ILS receivers (including marker beacons) and autopilot coupling Review all notes and discrepancies from this survey and the mechanic's own inspection procedures as you make your purchasing decision, and/or negotiate repairs and adjustment to sale price with the seller/broker/agent. This is a product of the American Bonanza Society Technical Services. Please address comments/suggestions to <bonanza8@bonanza.org>. 6 BEECH BONANZA • DEBONAIR • TRAVEL AIR • BARON PREPURCHASE SURVEY CHECKLIST 316-945-1700 • <www.bonanza.org>