Cessna 188 AGwagon

Tail wheel control arm Tail wheel push-rod 1 1- Insert the tail wheel pushrod into the hole on the tail wheel control arm (as show). 2- Re-install the rudder torque rod and tail wheel mount in place. 3- Secure the tail wheel mount in place using four 3x12mm screws. Secure the tail wheel control horn in place using a 1/8”(3mm) screw set, Ensure smooth non-binding movement. 1 2 1 A B Test-fit the rudder torque rod into the slot. 3 Rudder torque rod NOTE: You may need to open up the slots so that the torque rod bearing are not too difficult to push in 3x12mm screw ...........4 4- Tail wheel leg / Spornradtrager Note: All holes on the fuselage and bilnd-nuts are pre-installed at factory. 6- Main landing gear / Fahrwerk 4x15mm screw Aluminum landing gear 7- Wheel / Radl 8- Engine mount / Motortrager 4X15mm screw ...........6 4X30mm screw ......2 ..............2 ..............2 ! Align the mark on both mounts with the mark on the fuselage 4X25mm screw ......4 ..............4 ..............4 4.5mm .............2 Aluminum Haupfahrwerk Rudder servo Throttle servo Switch Nylon pushrod guide Nylon pushrod guider Rudder and tail wheel pushrod Elevator servo Elevator servo 9- Engine / Motor 10- Servo installation 11- Linkage / Alenkungen 140-141mm 140 - 141mm ! Engine thrust on balk head is already adjust at factory 1.5 TOP-VIEW .........2 2x20mm .......4 TOP VIEW / Draufsicht BOTTOM - VIEW / Unteransicht FUEL TANK RECEIVER BATTERY 2.5x10mm.....4 Attach the board or transparent plastic on the side of the fuselage with the adhesive tape as show. Using a pencil or felt tipped pen trace around the engine head where it meet the cowl. Cut the opening the board or trans- parent plastic for the engine head as marked above. Remove the engine and insert the cowl on to the fuselage so the distance from the fire wall to the front of the cowl is 138 to 139mm. Remove the cowl from the fuselage and carefully cut the opening for the engine head as marked above. Do the same way with the hole for needle-valve and silencer. Again. Insert the cowl on to the fuselage and secure it in place with five 2x5mm screws. 138mm Ruler 12- Fuel tank / Kraftstofftank 13- Cowling / Motorhaube SIDE-VIEW / Seitenansicht BATTERY STAND F3 F3 F2 F3A FUEL TANK STAND FUEL TANK BATTERY STAND LI-PO BATTERY Magnetic Battery stopper (3mm plywood) IN CASE OF LI-PO BATTERY USING Slide the battery stand throughout the slots on the bottom of F3 One end of the battery stand touched the rear of the fire-wall IN CASE OF GLOW ENGINE USING IN CASE OF ELECTRIC MOTOR USING Slide the battery stand (P1) throughout the slots on the bottom of F3 so that the end of the battery stand touched the rear of the fire-wall. Secure the battery stand in place using the magnetic battery stopper (P4). P1 Place the Li-po battery on to the battery stand and secure it in place with the nylon cable tie. Nylon cable tie F3 F2 Fire-wall 14- Li-po battery / Li-po akku SIDE-VIEW / Seitenansicht Insert the 18x500mm aluminum tube throughout the fuselage (do not using glue) L/R 2x10mm screw X X Flap servo hatch (plywood) Flap push rod exit Aileron servo Aileron push rod 305mm CA 1-Using the ABS shield as a template, trace around the outside edge of the ABS air-scoop,and then remove it. 2-Using a sharp hobby knife, cut away the covering inside the lines. Not to cut into the wood. 3-Apply the ABS shield in place and secure with CA glue. Do the same way with another half wing. Cut away the covering only WING - TOP VIEW 15- Servo 16- ABS Shield 17- Wing installation / Flachenbefestigung BOTTOM - VIEW / Unteransicht 5x20mm screw 5mm washer 5mm blindnut pre-installed inside. Wood dowel Wood dowell CA 1- Test-fit the dowel into the hole. 2- Secure the dowel in place using CA glue. Do the same way with another haft wing. Secure the half wing in place using 5x20mm screw. Do the same way with another half wing. Lightly, push the half wing to the side of fuselage. CA 19- Cockpit 18- Wing installation / Flachenbefestigung 5X20mm screw ......2 ..............2 CA Black nylon tube 20- Cockpit 21- Canopy / Kabinenhaube 2x12mm screw 3x15mm screw 22- Cockpit installation 2x12mm screw ...........5 3X15mm screw ...........2 Fiberglass shield 23- Wing brace 24- Tail shield 3x15mm ..........2 3x10mm screw 12mm 35mm 80mm ELEVATOR CONTROL RANGE RUDDER CONTROL RANGE Adjust the travel of each control surface to the values in the diagrams these values fit general flight capabilites. Readjust according to your needs and flight level. Position for right diagram. AILERON CONTROL RANGE FLAP CONTROL RANGE CG 40mm Position for right diagram. Position for right diagram. NEVER FLY BEFORE CHECKING THE CG’S REQUIRED POSITION. Carefully install the battery pack to ensure that they will not shift during flight. Shift the location of the battery pack as needed to obtain the specification. Position for right diagram(CG) 25- Tail shield 26- Control surface & Balance Schwerpunkt & Ruderausschlage 150 - 153mm 40mm 12mm 80mm All details are subject to change without notice ! Technische Anderungen und Irrtumer vorbehalten ! IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner to clean on surface of your model to keep the colour not fade. 3x10mm screw ...........4 2mm