TN72 Minor Change for CS-23 Aircraft

5.3 POST INSTALLATION CHECKS .................................................................................................. 12 5.3.1 Continuity Check ............................................................................................................ 12 5.3.2 Secure Looms .................................................................................................................. 12 5.3.3 Initial Power On ............................................................................................................. 12 5.3.4 TT21/22 Setup ................................................................................................................. 12 5.3.5 TT31 Setup ...................................................................................................................... 13 5.4 TEST ........................................................................................................................................ 13 5.4.1 Equipment Function ....................................................................................................... 13 5.4.2 Interference Effects ......................................................................................................... 14 5.4.3 Ramp Test ....................................................................................................................... 14 6. COMPLIANCE STATEMENT................................................................................................... 15 7. APPENDIX 1 ................................................................................................................................ 17 8. APPENDIX 2 ................................................................................................................................ 18 THIS DOCUMENT IS CONFIDENTIAL AND CONTAINS COMMERCIALLY SENSITIVE INFORMATION TO TRIG AVIONICS LTD AND PARTNER COMPANIES. THE CONTENTS OF THIS DOCUMENT ARE TO BE KEPT CONFIDENTIAL AND ARE NOT TO BE DISCLOSED TO THIRD PARTIES WITHOUT THE PRIOR WRITTEN CONSENT OF TRIG AVIONICS LTD. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 1 1. Preface 1.1 Purpose To document the Minor Change to install a TN72 GPS position source connected to a previously installed Trig TT21/22 or TT31 transponder. 1.2 Scope This Minor Change applies to unpressurised single engine piston aeroplane. The applicable aircraft are listed in Appendix 2. 1.3 Changes from Previous Issue None, this is the first issue 1.4 Changes Forecast None. 1.5 Document Cross-References 1.5.1 Internal Documents 01691-00 TN72 Installation Manual Issue AI 00455-00 TT31 Transponder Installation Manual Issue AR 00560-00 TT21/TT22 Transponder Installation Manual Issue AQ DEV/TN72/009 TN72 Declaration of Design Performance Issue 2.0 1.5.2 External Documents CS-23 (Amdt 5) Certification Specifications for Normal, Utility, Aerobatic, and Commuter Category Aeroplanes EASA CAP747 Mandatory Requirements for Airworthiness CAA ED-23C MOPS for airborne VHF Receiver - Transmitter Eurocae ETSO C199 ETSO for Traffic Awareness Beacon System (TABS) EASA 1.5.3 Approval Traceability Not applicable 1.6 Abbreviation and Acronyms The following abbreviations and acronyms are used in this document: ADS-B Automatic Dependant Surveillance Broadcast AFM Aircraft Flight Manual TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 2 DC Direct Current DDP Declaration of Design Performance EASA European Aviation Safety Agency ETSO European Technical Standards Order GNSS Global Navigation Satellite System GPS Global Positioning System MOPS Minimum Operational Performance Standard POH Pilots Operating Handbook TABS Traffic Awareness Beacon System TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 3 2. Introduction The TN72 TABS GPS Receiver is a TSO-C199 class B compliant GPS, suitable for use as an ADS-B position source for a Trig transponder. When installed in accordance with this minor change it forms part of a voluntary ADS-B Out system that is compatible with airborne traffic systems and surface surveillance equipment. The TN72 is a remote unit which is mounted within the aircraft cabin or avionics bay with connections to aircraft power, data connection to the transponder and connection to a suitable GPS antenna. The TN72 runs from either 14 volt nominal or 28 volt nominal DC power supply with no configuration changes required. This minor change describes the process of installing a TN72 with a preinstalled Trig TT21/22 or TT31 transponder and TA70 GPS antenna. The installation of these items can be accomplished using CS- STAN and therefore is not covered under this minor change for simplicity. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 4 3. Change Details 3.1 Description of Change 3.1.1 Installation Overview This change involves installing and configuring a Trig Avionics TN72 GPS Position source connected to a Trig Avionics TT21/22 or TT31 transponder. The installation will include physical mounting of the TN72, construction of a wiring loom, connection to a TA70 GPS antenna and configuration of the associated transponder. 3.2 Mechanical Details The TN72 is a remote mount unit that is installed within the aircraft cabin or avionics bay. The TN72 features connections for power, data and GPS antenna. The TN72 is compatible with any GPS antenna approved to ETSO C190 or C114a. For the purpose of this minor change, a separately installed Trig TA70 antenna will be used. The TN72 has a total weight of 110 grams. The effect on weight and balance of the aircraft will be small due to the low weight of the transceiver equipment. After the installation a weight and balance check should be calculated or performed in accordance with the manufactures instructions. 3.3 Continued Airworthiness Instructions Other than for periodic functional checks required by the regulations, the TN72 has been designed and manufactured to allow “on condition maintenance”. This means that there are no periodic service requirements necessary to maintain continued airworthiness, and no maintenance is required until the equipment does not properly perform its intended function. When service is required, a complete performance test as detailed in section 5.4 of these instructions should be accomplished following any maintenance action. 3.4 Installed Equipment Suitability 3.4.1 ETSO The TN72 is certified to ETSO C199 3.4.2 Environmental The environmental testing conducted for the TN72 is appropriate for this installation. Key aspects of the TN72 environmental qualification are summarised here: DO-160F reference Qualification Applicability Temperature & Altitude Category A2 and C1 Equipment intended for installation in a partially controlled temperature but pressurised location and installed is a non-pressurised but controlled temperature location. Loss of Cooling +70C without cooling air Forced air cooling not required. Temperature Variation Category B For a non temperature controlled or partially temperature controlled internal section of the aircraft. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 5 Humidity Category A Standard humidity environment. Operational Shock & Crash Safety Category B type 5 Equipment generally installed in fixed-wing aircraft or helicopters, VLA’s and sailplanes tested for standard operational shock and crash safety. Vibration Aircraft zone 2; type 3, 4, 5 to category S level M, type 1 (Helicopters) to category U level G Single engine fixed wing reciprocating or turboprop. Multi engine less than 5700Kg. Helicopters, reciprocating and turbojet engines. Equipment fitted to instrument panel, console or equipment rack. Magnetic Effect Category Z Equipment and or its connecting cable harness may be mounted within 0.3m of magnetic compass. All verified during ETSO environmental qualification testing. Power Input Category BX DC equipment intended for use on aircraft electrical system supplied by engine driven alternator or generator, where a battery of significant capacity is on the DC bus at all times. Voltage Spike Category B Installation where a lower standard of protection is acceptable. Audio Susceptibility Category B DC equipment intended for use on aircraft electrical system supplied by engine drive alternator or generator, where a battery of significant capacity is on the DC bus at all times. Induced Signal Susceptibility Category AC Equipment intended for operation where interference- free operation is desirable and installed on aircraft whose primary power is constant frequency or DC. RF Susceptibility Category TT Specified in the HIRF rules; representative of the internal EMI environment from aircraft equipment. RF Emission Category B Basic emission control. In each case the environmental qualification is appropriate to the installation in the instrument panel of a light piston engine aircraft with a DC electrical system. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 6 3.5 Drawings 3.5.1 Mounting fixing All dimensions in millimetres. The drawing is not to scale 3.6 Electrical Load Analysis The TN72 will typically draw under 0.08 Amps in normal operation based on a 14v DC supply and 0.04 Amps in normal operation based on an 18v DC supply. The TN72 wiring and circuit breaker rating to be used are specified in the accomplishment instructions. The TN72 is considered to be non-essential for continued safe flight. It will be installed with a circuit breaker separate to that of the transponder that allows the unit to be powered off by the pilot. On this basis, it can be concluded that the 30 minute battery requirement of CAP747 GR6 will be satisfied. 3.7 Flight manual/POH Amendments No AFM amendments are required as part of this Minor Change. A pilot operating booklet is provided with the associated transponder and this should be made available to the flight crew. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 7 4. Preparation 4.1 Equipment and tools required You will need the TN72 install kit and standard avionics workshop tooling. Depending on the transponder used, you will also require extra crimp pins to connect the new wiring loom to the existing transponder loom. Description Trig Part No Quantity TT21/22 Crimp Terminal, Male, 22-24 AWG 00729-00 2 TT31 Crimp Terminal, Female, 18-24 AWG 00236-00 2 4.2 Aircraft Voltage Ensure the aircraft voltage is between 11 and 33 volts. 4.3 TN72 Position The TN72 unit can be installed in any orientation as long as it is secured with four screws and locking nuts to a solid piece of structure in a suitable location that meets the following criteria:  Does not interfere with any primary flying controls.  Will not be subject to any damage or displacement due to person entering/exiting the aircraft.  Allows a suitable routing for any interconnecting wiring.  Will not be subject to adverse weather conditions such as rain, snow or ice. Example Location – Under panel 4.4 Protective devices The live power supply must be protected by a 1 Amp circuit breaker of such a type that can be put offline by the pilot. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 8 1 Amp Circuit breaker 4.5 Wiring 4.5.1 Power and Ground Ensure there is space in the panel to fit the addition 1 Amp circuit breaker required. All power and ground wires should be of the size and type detailed in the wiring diagrams. 4.5.2 Wire Routing Care must be taken to ensure surface damage does not occur to the wires during installation and that all wire looms are appropriately secured to prevent damage during its installed life. Ensure the loom does not chafe on any parts of the aircraft or interfere with any moving parts especially if you are using thin walled insulated wire to save on weight, such as MIL-22759/16, 17, 18 or 19. 4.5.3 Inspect the General Wiring Inspect any existing wiring for the general condition and gauge. The power wires should be AWG 20 or heavier; the other signal wires carry only light currents and may be any gauge appropriate to the mechanical environment. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 9 5. Accomplishment Instructions 5.1 TN72 Installation 5.1.1 Installing TN72 GPS Position Source Once a suitable location has been decided as per section 4.4, secure the TN72 using suitable screws. You should use an appropriate locking nut or similar to ensure the TN72 does not come loose during normal aircraft vibrations. Install the TN72 in accordance with the installation manual. 5.1.2 Wiring Loom Manufacture the connectors and wiring looms in accordance with the appropriate wiring diagrams in section 5.2. The power wires should be AWG 20 or heavier; the other signal wires carry only light currents and may be any gauge appropriate to the mechanical environment. Shielded wiring can be used if deemed appropriate the particular installation. Aircraft standard wire should be used for the installation. For example, wire that meets MIL-W- 22759/1 to 23, 32 to 35 specifications would be acceptable for this installation. Common wire types include MIL-W-22759/34 or Raychem 55 wire. Shielded wires should be to MIL-W-27500. When installing the TN72 to a TT31 either the primary 24 way or the secondary 12 way connection can be used. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 10 5.2 Wiring Diagrams Figure 1 – TN72 System Interconnect .................................................................................................... 11 TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 11 Figure 1 – TN72 System Interconnect TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 12 Antenna Connection Install the TA70 antenna in accordance with its fitting instructions. This should be accomplished using either a separate minor change or CS-STAN CS-SC004a. Install the antenna cable as per the TN72 installation manual. 5.3 Post Installation Checks 5.3.1 Continuity Check Perform a continuity check on all the newly installed wiring to ensure the correct connections have been made. 5.3.2 Secure Looms Ensure all the wiring is suitably secured and does not interfere with any flying controls. Make sure the wiring cannot be damaged or chaffed due to aircraft vibrations. 5.3.3 Initial Power On Apply power. The TN72 has no indicators of function on the unit and so functionality cannot be determined visually. The circuit breaker should remain untripped. 5.3.4 TT21/22 Setup Enter the setup menu by holding down the “Fn” button while powering the transponder on then press “Ent” when instructed. Setup the parameters as follows: VFR Flight ID, Mode S Address As per aircraft VFR Squawk As per customer preference Maximum Airspeed, Aircraft Category As per aircraft Squat Switch Type Auto on GPS data TIS Output None GPS Source C199 TABS GPS Interface Speed 9600 Aircraft Length, Aircraft Width, GPS Reference Position Offset, 1090MHz Receiver Installed As per aircraft UAT Receiver Installed No Press “Fn” to skip the voltage check and altimeter calibration. Power cycle the transponder when instructed. Refer to the Installation and Operation manuals for further information on each setup parameter. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 13 5.3.5 TT31 Setup Enter the setup menu by holding down the “Func” button while powering the transponder on, press “Ent” when instructed. Setup the parameters as follows: VFR Flight ID, Mode S Address As per aircraft VFR Squawk As per customer preference Maximum Airspeed, Aircraft Category As per aircraft Squat Switch Type Auto on GPS data ARINC TIS Output None If connection the TN72 on the primary connector use the following setting, otherwise leave at current values. Serial Input 1 GPS - C199 TABS Serial Output 1 Leave at current setting Interface 1 Speed 9600 If connection the TN72 on the secondary connector use the following setting, otherwise leave at current values. Serial Input 2 GPS - C199 TABS Serial Output 2 Leave at current setting Interface 2 Speed 9600 Aircraft Length, Aircraft Width, GPS Reference Position Offset, 1090MHz Receiver Installed As per aircraft UAT Receiver Installed No Audio Volume, LCD Dimmest Point, As per customer preference LCD Brightness Press “Func” to skip the external interface, altitude encoder and temperature checks. Confirm that the correct channel shows “GPS: *”. Press “Func” to skip forward and power cycle the transponder when instructed. Refer to the Installation and Operation manuals for further information on each setup parameter. 5.4 Test 5.4.1 Equipment Function Verify that the proper mechanical and electrical connections have been made. With the aircraft positioned with a clear view of the sky, power the transponder and TN72 and set the transponder to ALT mode and allow two minutes to for a GPS position to be established. Press the TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 14 “Fn” or “Func” key until “ADS-B POSN” is shown and verify that the latitude and longitude shown are correct for the current aircraft location. Check that the transponder is displaying GND on screen, indicating that the automatic air / ground determination has been successful. Pull the isolating circuit breaker to the TN72. Ensure that the “No ADS-B position” warning is shown within 20 seconds. Check that ALT is displayed on the screen within one minute, indicating that the transponder has reverted to airborne mode. Reset the circuit breaker and ensure the position returns within two minutes. 5.4.2 Interference Effects With the TN72 powered on, operate each of the other electrically operated aircraft systems to determine that no significant interference effects are present. 5.4.3 Ramp Test Using an IFR 6000 or other suitable transponder test set, confirm that the transponder gives an ADS-B positon comparable to the actual position and a SIL and SDA value of 1 during operation. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 15 6. Compliance Statement CS 23 Amdt 1 Para Requirement Compliance References 23.1301 (a) Installed equipment to be of a design appropriate to its intended function. TN72 is approved under ETSO C199. Review of certification basis in DDP completed. TN72 DDP. 23.1301 (b) Be labeled as to its identification, function or operating limitations. All controls are present. No limitations are recorded. ETSO compliance is shown on the product identification label. TN72 Installation Manual. 23.1301 (c) Be installed according to specified limitations Review of environmental testing, deviations and limitations in DDP completed. TN72 DDP. 23.1301 (d) Function properly when installed. System tested by ground and flight tests on completion Section 5.4, Post installation checks 23.1309 (a) System must not adversely affect existing systems The TN72 does not interface with and is physically separate from other aircraft systems apart from the transponder. Failure of the TN72 will not result in failure of the transponder. TN72 system integrity is commensurate with a minor failure condition and unit failure does not affect the correct function of other existing systems. EMI tests carried out post-installation. Section 5.2, Wiring Diagram. Section 5.4, Post installation checks 23.1351(a) Electrical system capacity 1 amp circuit breaker used supplying a maximum load of 0.1 amps. Wire gauge 20 appropriate. Effects on battery endurance will be negligible and the TN72 is not required equipment and can be powered off. Section 3.6, Electrical load analysis TN72 Installation Manual. 23.1357 Circuit Protective Devices New circuit breaker used. Section 4.8 of accomplishment instructions. 23.1431(a) Environmental conditions must be considered. Section 3.4.2, review of environmental testing. TN72 DDP. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 16 23.1431(b) Not adversely affect simultaneous operation of other radio or electronic systems or units. EMI tests carried out post-installation. Section 5.4, Post installation checks 23.1529 Instructions for Continued Airworthiness Other than for periodic functional checks required by the maintenance program, the TN72 GPS Position Source has been designed and manufactured to allow “on condition maintenance”. This means that there are no periodic service requirements necessary to maintain continued airworthiness, and no maintenance is required until the equipment does not properly perform its intended function. Section 3.3 Continued Airworthiness Instructions. CAP747, GR6 Battery duration not less than 30 minutes The TN72 has a maximum load of 0.1 amps. Effects on battery endurance will be negligible and the TN72 is not required equipment and can be powered off. TN72 Installation Manual. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 17 7. Appendix 1 TN72 Instructions for Continued Airworthiness 1. Description This document describes the necessary maintenance requirements and instructions necessary to ensure the continued airworthiness of the aircraft following the embodiment of the Minor Change to add the TN72 GPS Receiver. 2. Operation There are no specific operation instructions for the TN72 as all operation is automatic and handled by the associated transponder. Details of transponder operation can be found in the relevant transponder operating manual.  00454-00 TT31 Operating Manual  00559-00 TT21/22 Operating Manual 3. Servicing There are no periodic service requirements necessary to maintain continued airworthiness of the TN72 GPS Receiver. 4. Maintenance Instructions Please refer to your national approved aircraft maintenance program for any periodic functional checks that must be carried out on the transponder system. Other than for periodic functional checks required by the regulations, there are no periodic maintenance requirements necessary to maintain continued airworthiness. If a service is required, a complete performance test as detailed in section 5.4 of these instructions should be accomplished following any maintenance action. 5. Install and Removal Instructions Please refer to Trig Avionics TN72 Installation Manual;  01691-00 Installation Manual section Installation 6. Required Tools and Test Equipment  None 7. Airworthiness Limitations There are no Airworthiness Limitations applicable to the Trig Avionics Minor Change to install a TN72 GPS Receiver. TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 18 8. Appendix 2 Applicable aircraft types Type Certificate Holder CESSNA AIRCRAFT COMPANY Type Certificate Number FR 38, US A13EU, US A4EU, US A26EU, US A42EU, US A18EU, FR 43 Type Cessna F150/F152 Series Model F152 Model FA150K Model FA150L Model FA150M Model FA152 Model FRA150L Model FRA150M Model F150F Model F150G Model F150H Model F150J Model F150K Model F150L Model F150M Type Cessna F172 Series Model F172G Model F172H Model F172K Model F172L Model F172M Model F172N Model F172P Model FP172D Model F172D Model F172E Model F172F Type Cessna F177RG Model F177RG Type Cessna F182 Series Model F182P Model F182Q Model FR182 Type Cessna FR172 Series Model FR172E TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 19 Model FR172F Model FR172G Model FR172H Model FR172J Model FR172K Type Certificate Holder BRITTEN-NORMAN AIRCRAFT LTD. Type Certificate Number EASA.A.388, AAN 9405.1, AAN 10101, AAN 11529, AAN 10918, AAN 12401, AAN 11105, AAN 11108 Type BN2 Islander Series Aircraft Model BN2A-9 Model BN2B-20 Model BN2B-21 Model BN2 Model BN2A Model BN2A-10 Model BN2A-2 Model BN2A-20 Model BN2A-21 Model BN2A-23 Model BN2A-26 Model BN2A-27 Model BN2A-3 Model BN2A-6 Model BN2A-8 Model BN2B-26 Model BN2B-27 Type Certificate Holder AQUILA AVIATION INTERNATIONAL GMBH Type Certificate Number EASA.A.527 Type AQUILA AT01 Model AQUILA AT01-100 Model AQUILA AT01 Type Certificate Holder AVIAT AIRCRAFT INC Type Certificate Number EASA.IM.A.294, US A8SO Type Husky A-1 Model A-1 Model A-1A Model A-1B TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 20 Model A-1C-180 Type Pitts S-1/-2 Model S-1S Model S-2A Model S-2B Model S-2C Model S-2S Type Certificate Holder CIRRUS DESIGN CORPORATION Type Certificate Number EASA.IM.A.007 Type Cirrus SR-20, SR-22 Model SR20 Model SR22 Model SR22T Type Certificate Holder DIAMOND AIRCRAFT INDUSTRIES Type Certificate Number EASA.A.005, EASA.A.513, EASA.A.439, EASA.A.065, EASA.A.066 Type DA 42 Model DA 42 Model DA 42 M Model DA 42 M-NG Model DA 42 NG Model DA 62 Type DA 42 M (Restricted) Model DA 42 M (Restricted) Model DA 42 M-NG (Restricted) Type DV 20 Model DV 20 Model DV 20 E Type H 36 Model H 36 "Dimona" Model HK 36 "Super Dimona" Model HK 36 R "Super Dimona" Model HK 36 TC Model HK 36 TS Model HK 36 TTC Model HK 36 TTC-ECO Model HK 36-TTS Type HK 36 TTC-ECO Model HK 36 TTC-ECO TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 21 Type Certificate Holder E.I.S. AIRCRAFT GMBH Type Certificate Number DE TC 666, DE TC 695, DE 1014, DE TC 755 Type Fournier RF 3 Model Fournier RF 3 Model Fournier RF 4 Model Fournier RF 4 D Type Fournier RF 5 Model Fournier RF 5 Model Fournier RF 5 B "Sperber" Type RS 180 Model RS 180 Type SFS 31 "Milan" Model SFS 31 "Milan" Type Certificate Holder EVEKTOR, SPOL. S R.O. Type Certificate Number EASA.A.029, EASA.A.046, EASA.A.592 Type EV-97 VLA Model EV-97 VLA Type L 13 Vivat Model L 13 SDL Vivat Model L 13 SDM Vivat Model L 13 SE Vivat Model L 13 SEH Vivat Model L 13 SL Vivat Model L 13 SW Vivat Type SportStar RTC Model SportStar RTC Type Certificate Holder EXTRA Type Certificate Number EASA.A.362 Type EA 300 Model EA 300 Model EA 300/200 Model EA 300/L Model EA 300/LC Model EA 300/LT Model EA 300/S Model EA 300/SC TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 22 Type Certificate Holder FUJI HEAVY INDUSTRIES LTD. Type Certificate Number JP 20-10, JP 22-2, JP 22-6 Type FA-200 Model FA-200-160 Model FA-200-180 Model FA-200-180AO Type Certificate Holder GROB AIRCRAFT AG Type Certificate Number EASA.A.075, EASA.A.565, DE TC 817, EASA.A.364 Type G 120 Model G 120A Model G 120A-I Type G 120TP Model G 120TP-A Type G109 Model G109 Model G109 B Type Grob G 115 Model G 115 Model G 115A Model G 115B Model G 115C Model G 115C2 Model G 115D Model G 115D2 Model G 115E Model G 115EG Model G 115TA Type Certificate Holder HB-FLUGTECHNIK GMBH Type Certificate Number EASA.A.434, EASA.A.433 Type HB 21 Model HB 21 Model HB 21 V1 Model HB 21 V2 Model HB 21/2400 Model HB 21/2400 B Type HB 23/2400 Model HB 23/2400 Model HB 23/2400 SP TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 23 Model HB 23/2400 Scanliner Model HB 23/2400 V2 Type Certificate Holder M & D FLUGZEUGBAU GMBH Type Certificate Number EASA.A.252 Type AVO 68 - v "Samburo" Model AVO 68 - R "Samburo" Model AVO 68 - R 100 "Samburo" Model AVO 68 - R 115 "Samburo" Model AVO 68 - s "Samburo" Model AVO 68 - v "Samburo" Type Certificate Holder PILATUS AIRCRAFT LTD. Type Certificate Number CH F 56-10 Type PC-6 Model PC-6 Model PC-6-H1 Model PC-6-H2 Model PC-6/350 Model PC-6/350-H1 Model PC-6/350-H2 Model PC-6/A Model PC-6/A-H1 Model PC-6/A-H2 Model PC-6/A1-H2 Model PC-6/A2-H2 Model PC-6/B-H2 Model PC-6/B1-H2 Model PC-6/B2-H2 Model PC-6/B2-H4 Model PC-6/C-H2 Model PC-6/C1-H2 Type Certificate Holder PZL WARSZAWA-OKECIE S.A. Type Certificate Number EASA.A.061, EASA.A.444, EASA.A.091 Type PZL-104 Wilga Series Model PZL-104 Wilga 32 Model PZL-104 Wilga 32A Model PZL-104 Wilga 35 Model PZL-104 Wilga 35A Model PZL-104 Wilga 80 TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 24 Model PZL-104M Wilga 2000 Model PZL-104MA Wilga 2000 Model PZL-104MF Wilga 2000 Model PZL-104MN Wilga 2000 Type PZL-106 BT TURBO KRUK Series Model PZL-106 BT-601 TURBO KRUK Model PZL-106 BTU-34 TURBO KRUK Type PZL-KOLIBER Series Model PZL-110 KOLIBER Model PZL-KOLIBER 150 Model PZL-KOLIBER 150A Model PZL-KOLIBER 160A Type Certificate Holder SLINGSBY ADVANCED COMPOSITES Type Certificate Number EASA.A.390 Type T67 Model T67A Model T67B Firefly Model T67C Firefly Model T67M Firefly Model T67M-MKII Firefly Model T67M200 Firefly Model T67M260 Firefly Model T67M260-T3A Firefly Type Certificate Holder SOCATA Type Certificate Number EASA.A.377, EASA.A.379, EASA.A.378 Type MS 880 and Rallye 100 Series Model MS 880 B Model MS 880 B-D Model MS 881 Model MS 883 Model MS 884 Model MS 885 Model MS 886 Model MS 887 Model Rallye 100 S Model Rallye 100 S-D Model Rallye 100 ST Model Rallye 100 ST-D TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 25 Model Rallye 110 ST Model Rallye 150 ST Model Rallye 150 ST-D Model Rallye 150 SV Model Rallye 150 SVS Model Rallye 150 T Model Rallye 150 T-D Model Rallye 180 T Model Rallye 180 T-D Model Rallye 180 TS Type MS 890 and Rallye 235 Series Model MS 890 A Model MS 890 B Model MS 892 A.150 Model MS 892 B.150 Model MS 892 E-D.150 Model MS 892 E.150 Model MS 893 A Model MS 893 B Model MS 893 E Model MS 893 E-D Model MS 894 A Model MS 894 C Model MS 894 E Model RALLYE 235 A Model RALLYE 235 C Model RALLYE 235 E Model RALLYE 235 E-D Model RALLYE 235 F Type TB Series Model TB 10 Model TB 20 Model TB 200 Model TB 21 Model TB 9 Type Certificate Holder STEMME AG Type Certificate Number EASA.A.054 Type Stemme S10 Model Stemme S10 TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 26 Model Stemme S10-V Model Stemme S10-VT Model Stemme S12 Type Certificate Holder SYMPHONY AIRCRAFT INDUSTRIES Type Certificate Number EASA.IM.A.031 Type OMF-100 Model OMF-100-160 Type Certificate Holder TECHNOFLUG LEICHTFLUGZEUGBAU Type Certificate Number DE TC 880 Type CARAT Model CARAT Type Certificate Holder TRUE FLIGHT HOLDINGS LLC Type Certificate Number US A16EA, US A11EA Type AA-5 Model AA-5 Model AA-5A Model AA-5B Model AG-5B Type AA-1 Model AA-1 Model AA-1A Model AA-1B Model AA-1C Type Certificate Holder COMMANDER AIRCRAFT CORPORATION Type Certificate Number US A12SO Type Commander 112/114 Series Model 112 Model 112B Model 112TC Model 112TCA Model 114 Model 114A Model 114B Model 114TC Type Certificate Holder COSTRUZIONI AERO. TECNAM TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 27 Type Certificate Number EASA.A.006 Type P2002 Model P2002-JF Model P2002-JR Type Certificate Holder BEECHCRAFT CORPORATION Type Certificate Number US 5A4, US A23CE, US A29CE, US A30CE, US A1CE Type 50 (Twin Bonanza) Model 50 Model B50 Model C50 Model D50 Model D50A Model D50B Model D50C Model D50E Model D50E-5990 Model E50 Model F50 Model G50 Model H50 Model J50 Type 58 Model 58P Model 58PA Model 58TC Model 58TCA Type 76 (Duchess) Model 76 Type 77 (Skipper) Model 77 Type Hawker Beechcraft 19, 23, 24 Model 19A Model 23 Model A23 Model A23-19 Model A23-24 Model A23A Model A24 Model A24R TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 28 Model B19 Model B23 Model B24R Model C23 Model C24R Model M19A Type Certificate Holder DIAMOND AIRCRAFT IND. INC Type Certificate Number EASA.IM.A.223, EASA.IM.A.022, EASA.IM.A.629 Type DA 20 Model DA 20-A1 Model DA 20-C1 Type DA 40 Model DA 40 Model DA 40 D Model DA 40 F Model DA 40 NG Type DA 62 Model DA 62 Type Certificate Holder MAULE AEROSPACE TECHNOLOGY Type Certificate Number EASA.IM.A.018 Type Maule Model Bee Dee M-4 Model M-4 Model M-4-180V Model M-4-210 Model M-4-210C Model M-4-220 Model M-4-220C Model M-4-220S Model M-4C Model M-4S Model M-4T Model M-5-180C Model M-5-210C Model M-5-235C Model M-6-235 Model M-7-235 Model M-7-235B TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 29 Model MT-7-235 Model MX-7-180 Model MX-7-180A Model MX-7-180B Model MX-7-180C Model MX-7-235 Model MXT-7-160 Model MXT-7-180 Model MXT-7-180A Type Certificate Holder MOONEY AVIATION COMPANY, INC. Type Certificate Number US 2A3, EASA.IM.A.266, US A6SW Type M20 Model M20 Model M20A Model M20B Model M20C Model M20D Model M20E Model M20F Model M20G Model M20J Model M20K Model M20L Model M20M Model M20R Model M20S Type M22 Model M22 Type Certificate Holder PIPISTREL D.O.O. AJDOVSCINA Type Certificate Number EASA.A.573 Type Virus SW 121 Model Virus SW 121 Type Certificate Holder QUEST AIRCRAFT DESIGN LLC Type Certificate Number EASA.IM.A.632 Type Kodiak 100 Series Model Kodiak 100 TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 30 Type Certificate Holder ZLIN AIRCRAFT A.S. Type Certificate Number EASA.A.353, EASA.A.443, EASA.A.027, EASA.A.028, EASA.A.108 Type ZLIN Z 26 Series Model Z 126 Model Z 126 T Model Z 226 A Model Z 226 B Model Z 226 M Model Z 226 MS Model Z 226 T Model Z 326 Model Z 326 A Model Z 326 M Model Z 526 Model Z 526 A Model Z 526 AFS Model Z 526 AFS-V Model Z 526 F Model Z 526 L Model Z 526 M Model Z 726 Model Z 726 K Type ZLIN Z 37 T Series Model Z 137 T Model Z 37 T Type ZLIN Z 42 Series Model Z 142 Model Z 142 C Model Z 242 L Model Z 42 M Model Z 42 MU Type ZLIN Z 43 Series Model Z 143 L Model Z 143 LSi Model Z 43 Type ZLIN Z 50 Series Model Z 50 L Model Z 50 LA Model Z 50 LS Model Z 50 LX TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 31 Model Z 50 M Type Certificate Holder PIPER AIRCRAFT, INC. Type Certificate Number US 1A10, US 1A15, US 2A13, EASA.IM.A.234, US A1EA, US A20SO, US A3SO, EASA.IM.A.239, US A7SO, EASA.IM.A.090, US A9SO, US A10SO, US A18SO, EASA.IM.A.232 Type PA-23 Model PA-23-235 Model PA-23-250 Model PA-E23-250 Type PA-24 (Comanche) Model PA-24 Model PA-24-250 Model PA-24-260 Model PA-24-400 Type PA-28 Model PA-28-140 (Cherokee Cruiser) Model PA-28-150 (Cherokee) Model PA-28-151 (Cherokee Warrior) Model PA-28-160 (Cherokee) Model PA-28-161 Model PA-28-161 (Warrior II) Model PA-28-161 (Warrior III) Model PA-28-180 (Archer) Model PA-28-180 (Cherokee) Model PA-28-181 (Archer II) Model PA-28-181 (Archer III) Model PA-28-201T (Turbo Dakota) Model PA-28-235 (Cher.Pathfinder) Model PA-28-236 (Dakota) Model PA-28R-180 (Arrow) Model PA-28R-200 (Arrow II) Model PA-28R-200 (Arrow) Model PA-28R-201 (Arrow III) Model PA-28R-201T (Turbo Arrow III) Model PA-28RT-201 (Arrow IV) Model PA-28RT-201T (Turbo Arrow IV) Model PA-28S-160 (Cherokee) Model PA-28S-180 (Cherokee) TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 32 Type PA-30, PA-39, PA-40 Model PA-30 Model PA-39 Model PA-40 Type PA-31 (Navajo) Model PA-31 Model PA-31-300 Model PA-31-325 Model PA-31-350 (Chieftain) Type PA-32 Model PA-32-260 (Cherokee Six 260) Model PA-32-300 (Cherokee Six 300) Model PA-32-301 (Saratoga) Model PA-32-301FT (Piper 6X) Model PA-32-301T (Turbo Saratoga) Model PA-32-301XTC (Piper 6XT) Model PA-32R-300 (Lance) Model PA-32R-301 (Saratoga II HP) Model PA-32R-301 (Saratoga SP) Model PA-32R-301T (Saratoga II TC) Model PA-32R-301T (Turbo SaratogaSP) Model PA-32RT-300 (Lance II) Model PA-32RT-300T (Turbo Lance II) Model PA-32S-300 (Cher.Six Seaplane) Type PA-34 Model PA-34-200 (Seneca) Model PA-34-200T (Seneca II) Model PA-34-220T (Seneca III) Model PA-34-220T (Seneca IV) Model PA-34-220T (Seneca V) Type PA-36 (Normal category) Model PA-36-285 (Normal category) Model PA-36-300 (Normal category) Model PA-36-375 (Normal category) Type PA-36 (Restricted category) Model PA-36-285 (Restricted) Model PA-36-300 (Restricted) Model PA-36-375 (Restricted) Type PA-38 Model PA-38-112 TN72 Minor Change for CS-23 Aircraft 20 April 2018 SUP/TN72/001 Issue 1.0 ______________________ Trig Avionics Limited Page 33 Type PA-44 Model PA-44-180 (Seminole) Model PA-44-180T (Turbo Seminole) Type Certificate Holder CUB CRAFTERS, Inc. Type Certificate Number EASA.IM.A.638 Type CC19-180 Model CC19-180