Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure
CESSNA P337 · Flight Manual
Overview
This Service Letter provides critical maintenance information regarding the CD Series combustion heaters used in various aircraft, including the Cessna P337 and T337H. It details a configuration change involving the replacement of the existing welded heater fuel solenoid shroud with a new die-formed version. This change aims to improve product reliability and standardize part numbers across the Janitrol Aero combustion heater lines. The document outlines the necessary materials, removal and installation procedures, and safety warnings to ensure compliance with the latest revisions. It is essential for maintenance personnel to follow these guidelines to maintain safety and operational integrity.
- This Service Letter applies to Cessna P337 and T337H models.
- The document outlines a change from a welded to a die-formed heater fuel solenoid shroud.
- Specific part numbers for materials required are listed in Table 1.
- Installation procedures must be performed by qualified personnel to ensure safety.
- Operational checks must be conducted post-installation to verify functionality.
Document
Source
Originally published by janitrol.aero. Sprinkle hosts a reference copy with an added summary, specifications and searchable full text.
Document details
- Type
- Flight Manual
- Year
- 2018
- Pages
- 10
- File size
- 508 KB
- Publisher
- janitrol.aero
Common. Rarer than 17% of the aircraft models we track.
Most owners only have the POH. Here's the essential set for the CESSNA P337.
- Pilot's Operating Handbook / AFM
- Checklist
- Maintenance Manual
- Parts Catalog (IPC)
- Systems & Wiring
- Service Bulletins
- Type Certificate (TCDS)
CESSNA P337 for sale now
Free — save the P337 to your watchlist and track it in one place.
More CESSNA P337manuals & documents
- Parts CatalogParts Catalog
- Short Term Monitoring Program VIC, Oak Park ReportOther Documents
- Short Term Monitoring Program VIC, Strathmore ReportOther Documents
- Airworthiness DirectiveAirworthiness Directives
- Aircraft Accident Briefs - Brief Format U.S. Civil and Foreign AviationOther Documents
- GUIDELINES FOR THE DESIGN OF AIRCRAFT WINDSHIELD/CANOPY SYSTEMSOther Documents
- Cessna P337 ChecklistChecklist
- Pneumatics Application Guide & AccessoriesSupplemental Type Certificate
- CESSNA 337 SKYMASTER Instruction ManualWeight And Balance
- MPS-3 FSARChecklist
If you fly the CESSNA P337, you may also be researching these.
In this document
Planning Information
This section outlines the effectivity of the Service Letter, indicating that all Hartzell Engine Technologies LLC CD series combustion heaters with specific part and serial numbers are affected. It emphasizes the importance of using the most recent revision of the Service Letter to avoid unsafe conditions.
Material Required
A list of materials needed for the replacement of the fuel solenoid shroud is provided, including specific part numbers for the upper and lower shrouds, screws, fittings, nuts, washers, gaskets, and labels.
Accomplishment Instructions
Detailed instructions for removing the old welded heater fuel solenoid shroud and installing the new configuration are included. The steps emphasize safety precautions, proper handling of components, and the need for qualified personnel to perform the work.
Return to Service
After installation, a heater operational check must be performed in accordance with the applicable aircraft maintenance manual, AFM, or POH to ensure proper functionality.
Contact Information
For technical support regarding this Service Letter, contact Hartzell Engine Technologies LLC via phone, fax, or email. The address for correspondence is also provided.
Safety notes
- Do not use obsolete or outdated information; always refer to the most recent revision of this Service Letter.
- Improper installation may result in unsafe conditions, including potential fuel leaks.
Full document text
1. Planning Information A. Effectivity (1) All Hartzell Engine Technologies LLC (HET) CD series combustion heaters with part numbers shown in Table 1 using an external fuel solenoid contained in a shroud assembly are affected by this Service Letter (SL). (2) All HET CD series combustion heaters with serial number HA17060001 and prior are affected by this Service Letter. WARNING: DO NOT USE OBSOLETE OR OUTDATED INFORMATION. PERFORM ALL WORK IN ACCORDANCE WITH THE MOST RECENT REVISION OF THIS SERVICE LETTER. THE INFORMATION CONTAINED IN THIS SERVICE LETTER MAY BE SIGNIFICANTLY CHANGED FROM EARLIER REVISIONS. FAILURE TO COMPLY WITH THIS SERVICE LETTER OR THE USE OF OBSOLETE INFORMATION MAY CREATE AN UNSAFE CONDITION THAT MAY RESULT IN DEATH, SERIOUS BODILY INJURY, AND/OR SUBSTANTIAL PROPERTY DAMAGE. REFER TO THE JANITROL.AERO WEBSITE FOR THE MOST RECENT REVISION LEVEL OF THIS SERVICE LETTER. B. Concurrent Requirements (1) None C. Reason: (1) As a product improvement and part number consolidation effort, HET has decided to replace the existing welded heater fuel solenoid shroud and associated hardware with a die formed version on CD series combustion heaters. (2) Replacing the welded heater fuel solenoid shroud with the die formed version will provide common part numbers across the Janitrol Aero combustion heater lines. (3) This change is being implemented on new and factory rebuilt combustion heaters. There is no requirement to change shrouds in the field, however, the previous configuration of the welded heater fuel solenoid shroud will no longer be available. 2900 Selma Highway Montgomery, AL 36108 USA Tel: 334-386-5400 Fax: 334-386-5450 Service Letter Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure Rev. New: March 02/18 SL 060 © 2018 - Hartzell Engine Technologies. - All rights reserved Page 1 of 10 D. Description (1) This publication provides Additional Maintenance Information (AMI). (2) This Service Letter provides notification that a configuration change has been made as a product improvement and part number consolidation effort. (3) This configuration change requires new Janitrol Aero style heater fuel solenoid shroud and hardware. Instructions for the change or repair of the new configuration are included. E. Approval (1) FAA acceptance has been obtained on the technical data in this publication that affects type design. F. Manpower (1) No addtional time required when performed at overhaul. G. References (1) HET P/N MM10001 Overhaul Manual Rev. L or later FAA approved revision. H. Other Publications Affected (1) None 2. Material Required A. As desired at overhaul or repair requiring replacement of the CD series fuel solenoid shroud, the following material is required: (1) One (1) each, Upper Shroud, fuel solenoid, HET P/N from Table 1 as applicable. (2) One (1) each, Lower Shroud, fuel solenoid, HET P/N from Table 1 as applicable. (3) Two (2) each, Screw, Upper Shroud, HET P/N 86D38-2. (4) One (1) each, Fitting, 90˚, HET P/N 81030. (5) One (1) each, Nut, fitting, P/N MS36591-45. (6) One (1) each, Washer, fitting, P/N AN960-916L. (7) One (1) each, Gasket, fitting, HET P/N F44A06. (8) One (1) each, Grommet, P/N MS35489-6. (9) One (1) each, Grommet, P/N MS35489-8S fuel solenoid shroud. (10) One (1) each, Label, fuel filter, HET P/N 81031. SL 060 Rev. New: March 02/18 Page 2 of 10 © 2018 - Hartzell Engine Technologies. - All rights reserved Service Letter Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure 3. Accomplishment Instructions WARNING 1: THIS PROCEDURE MUST BE PERFORMED BY COMPETENT AND QUALIFIED PERSONNEL WHO ARE FAMILIAR WITH AIRCRAFT MAINTENANCE THAT IS SPECIFIC TO THE CABIN HEATING SYSTEM. FAILURE TO DO SO MAY RESULT IN ECONOMIC LOSS, EQUIPMENT DAMAGE, AND/OR PHYSICAL INJURY. WARNING 2: DO NOT USE OBSOLETE OR OUTDATED INFORMATION. PERFORM ALL INSPECTIONS OR WORK IN ACCORDANCE WITH THE MOST RECENT REVISION OF THIS SERVICE LETTER AND THE APPLICABLE AIRCRAFT AND/OR HET HEATER MAINTENANCE MANUALS. INFORMATION CONTAINED IN THESE MANUALS OR THIS SERVICE LETTER MAY BE SIGNIFICANTLY CHANGED FROM EARLIER REVISIONS. THE USE OF OBSOLETE INFORMATION MAY CREATE AN UNSAFE CONDITION THAT MAY RESULT IN DEATH, SERIOUS BODILY INJURY, AND/OR SUBSTANTIAL PROPERTY DAMAGE. CAUTION: DO NOT DEPEND ON THIS SERVICE LETTER FOR GAINING ACCESS TO THE HEATER INSTALLED IN THE AIRCRAFT. ACCESS REQUIRES THE USE OF THE APPLICABLE MANUFACTURER’S MAINTENANCE MANUALS OR SERVICE INSTRUCTIONS. IN ADDITION, ANY PREFLIGHT OR IN FLIGHT OPERATIONAL CHECKS REQUIRE USE OF THE APPROPRIATE AFM OR POH. A. Removal of the welded heater fuel solenoid shroud (original configuration). Refer to Fig. 1. NOTE: HET does not require that the existing heater fuel solenoid shroud be replaced unless damaged or other problems exist. The improved version may be installed as desired at overhaul or other convenient maintenance. (1) Ensure Master Power is OFF and the Fuel Selector is in the OFF position. (2) Disconnect the overboard drain tube from the fuel solenoid base shroud. (3) Remove the two (2) screws retaining the fuel solenoid shroud cover and remove cover. (4) Remove grommet P/N 60533 from the end of base shroud. (5) Provide a small container to contain any fuel in the heater fuel line while the line is being removed. (6) While holding the fuel filter housing with an appropriate size wrench, loosen the B-nut and disengage the fuel line. (a) Do not loosen the fuel filter housing unless the filter will be changed. Rev. New: March 02/18 SL 060 © 2018 - Hartzell Engine Technologies. - All rights reserved Page 3 of 10 Service Letter Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure (7) Follow the fuel solenoid electrical wires back to the terminal connector and disconnect. (8) Remove the grommet supporting the electrical wires and pull wires through the hole one at a time.
Show full textShow less
(9) Using a 3/4 inch wrench on the hex end of the valve, unscrew the fuel solenoid from the fuel feed elbow fitting (rotate counter clockwise looking at the elbow fitting). (a) Remove the fuel solenoid assembly from the base shroud. CAUTION: WHILE LOOSENING THE NUT AT THE BASE OF THE ELBOW FITTING, THE FUEL FEED FITTING MUST NOT MOVE. MOVEMENT OF THE FITTING MAY CRACK THE BRAZING AT THE DOUBLE WALLED FUEL FEED LINE AND CREATE A FUEL LEAK. ALWAYS HOLD THE INLET FITTING BY THE FLATS FROM INSIDE THE HEATER. (10) If equipped, remove the four (4) or eight (8) screws, depending on heater model, holding the ventilating fan endplate. (a) Remove the fan endplate. (11) It may be necessary to remove the ventilating fan in order to access the back of the fuel feed tubes. Remove if necessary. (a) Measure the length of the motor shaft protruding from the fan and record dimension for use during re-assembly. (b) Loosen the Allen screw and remove the ventilating fan. (12) Hold the fuel feed inlet fitting in postition using a long reach 7/8 in. wrench across the flats. Refer to Fig. 1a detail. (a) Remove the elbow fitting. (b) Remove the 7/8 nut and washer holding the fuel shroud base and fuel feed inlet. (c) Remove the fuel shroud base and fuel shroud base gasket. B. Installation of the current series heater fuel solenoid shroud (new configuration). Refer to Figure 2. NOTE: Prior to starting installation, it is necessary to obtain the part number of the upper and lower fuel shroud needed for the specific heater part number. Refer to Table 1 for assistance in choosing the correct replacement part numbers. (1) Install a new gasket HET P/N F44A06 over the heater fuel feed inlet. (2) Install the new lower fuel shroud over the heater fuel feed inlet. Refer to Table 1 for P/N. (3) Install a new washer P/N AN960-916L and nut P/N MS36591-45 on the heater fuel feed inlet finger tight . SL 060 Rev. New: March 02/18 Page 4 of 10 © 2018 - Hartzell Engine Technologies. - All rights reserved Service Letter Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure CAUTION: WHEN THE NUT AT THE FUEL FEED INLET FITTING IS TIGHTENED, THE FITTING MUST NOT MOVE. MOVEMENT OF THE FITTING MAY CRACK THE BRAZING AT THE DOUBLE WALLED FUEL FEED LINE AND CREATE A FUEL LEAK. ALWAYS HOLD THE INLET FITTING BY THE FLATS FROM INSIDE THE HEATER. (4) Hold the fuel feed inlet fitting using a long-reach 7/8 in. wrench across the flats. Refer to Figure 1a. (a) Tighten nut P/N MS36591-45 on the heater fuel feed. (5) Place a small quantity of thread sealant, Loctite® NS5109 Gasket Maker or equivalent, on the pipe thread of the 90˚ Fitting HET P/N 81030. (6) Install the HET P/N 81030 Fitting into the fuel feed fitting and tighten. (a) Align the HET P/N 81030 Fitting so the fuel solenoid will be centered in the lower fuel shroud. (7) Install the fuel solenoid and filter assembly into the lower fuel solenoid shroud. (a) Place a small quantity of thread sealant, Loctite® NS5109 Gasket Maker or equivalent, on the pipe thread of the fuel solenoid and install into the 90˚ Fitting. (b) Tighten using a 3/4 inch wrench on the valve hex end. (8) Install the fuel solenoid electrical wires by pulling through the hole in the lower shroud one at a time. (a) Install the P/N MS35489-6 grommet. (9) Connect the fuel solenoid electrical wires at the existing terminal connector. (10) Connect the fuel solenoid fuel supply B-nut finger tight. (11) While holding the fuel filter housing with an appropriate size wrench, tighten the B-nut to the specified torque shown in the applicable aircraft maintenance or service manual. (12) Install new grommet P/N MS35489-8S into the end of lower fuel solenoid shroud. (13) If the ventilating fan was removed, re-install on motor shaft using dimension recorded in step 3.A.(11).(a) and tighten the Allen screw. (14) If removed, reinstall the ventilating fan endplate and tighten four (4) or eight (8) screws, depending on heater model, holding the ventilating fan endplate. (15) Prior to installing the upper fuel solenoid shroud, apply heater fuel pressure to check for leaks in the fuel solenoid, filter, fittings, and B-nut of the inlet fuel. (a) To apply heater fuel pressure, refer to the applicable aircraft service or maintenance manual, AFM or POH. Rev. New: March 02/18 SL 060 © 2018 - Hartzell Engine Technologies. - All rights reserved Page 5 of 10 Service Letter Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure Service Letter Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure (16) Install upper fuel solenoid shroud. (a) Install two (2) upper fuel solenoid shroud screws and tighten. (b) Install a P/N 81031 label on the upper fuel shroud. (17) Connect the overboard drain line from the lower fuel solenoid shroud. Location may vary. C. Return to Service (1) Perform a heater operational check in accordance with the applicable aircraft maintenance manual, AFM, or POH. 4. Contact Information A. Contact HET Product Support for all communications regarding the technical content of this Service Letter. (1) Phone +1.334.386.5400 (Option 2) (2) Fax +1.334.386.5450. (3) E-mail at techsupport@HartzellEngineTech.com. (4) Address Hartzell Engine Technologies LLC 2900 Selma Highway Montgomery, AL 36108 USA. SL 060 Rev. New: March 02/18 Page 6 of 10 © 2018 - Hartzell Engine Technologies. - All rights reserved Rev. New: March 02/18 SL 060 © 2018 - Hartzell Engine Technologies. - All rights reserved Page 7 of 10 Service Letter Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure Figure 1 - Fuel Solenoid Shroud & Hardware (Welded Version) Grommet P/N 60533 (use only with welded shroud) Shroud Cover P/N No Longer Available 90˚ Fitting P/N 22209 (use only with welded shroud) Grommet P/N 60531 (use only with welded shroud) Nut P/N 21393 Washer P/N 60103 (use only with welded shroud) Gasket P/N CD21518 (use only with welded shroud) Shroud Body P/N No Longer Available Screw (2) HET P/N CD60002 (use only with welded shroud) Existing Fuel Solenoid. Existing Fuel Feed Tube. (See Fig. 1a Detail) Fuel Filter & Housing Figure 1a - CD Series Fuel Feed Assembly Flats 7/8 in. Threaded Fuel Inlet Fuel Inlet Fitting Drain Tube (location may vary) SL 060 Rev. New: March 02/18 Page 8 of 10 © 2018 - Hartzell Engine Technologies. - All rights reserved Service Letter Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure Figure 2 - New HET Fuel Solenoid Shroud & Hardware (Formed Version) Grommet P/N MS35489-8S Upper Shroud P/N from Table 1 90˚ Fitting HET P/N 81030 Grommet HET P/N MS35489-6 Nut P/N MS36591-45 Gasket HET P/N F44A06 Lower Shroud P/N from Table 1 Drain Tube (location may vary) Screw (2) HET P/N 86D38-2 Existing Fuel Solenoid. Heater Jacket Existing Fuel Feed Tube. (See Fig. 1a Detail) Fuel Filter & Housing Washer P/N AN960-916L Rev. New: March 02/18 SL 060 © 2018 - Hartzell Engine Technologies. - All rights reserved Page 9 of 10 Service Letter Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure Heater Part No. Orig Heater Aircraft New Lower New Upper CD11010-1 C&D Velocity 87D77-3 87D69-1 CD11014-1 37D88, A37D88, B37D88 (Janitrol) Bell 206A, 206B 87D77-1 87D69-1 CD11047-1 74D01, -1, -2, -3EL (Janitrol) Diamond DA-42 L 87D77-3 87D69-1 CD11049-1 74D01, -1, -2, -3EL (Janitrol) Cessna P337, T337H 87D77-1 87D69-1 CD11050-1 42D79, -1 (Janitrol) Cessna 337, A to H, T337, B to H 87D77-3 87D69-1 CD11214-1 979-B1, 940 (South Wind) Cessna 337, A to H, T337, B to H 87D77-2 87D69-1 CD11215-1 940 (South Wind) Lake LA-4, A, P, LA4-200 87D77-3 87D69-1 CD12003-1 22D25, -1 EL (Janitrol) Aerostar PA60-600, 601 87D77-3 87D69-1 CD12004-1 23E62, -1, -2 EL (Janitrol) Piper PA31T3 T1040 87D77-3 87D69-1 CD12006-1 940 (South Wind) Piper PA30 Twin Commanche 87D77-3 87D69-1 CD12007-1 96D75, -1 (Janitrol) Twin Commander 700 87D77-3 87D69-1 CD12008-1 STC kit rear heater SA02487CH Navion, A, B, C, D, E, F, G 87D77-3 87D69-1 CD12009-1 A34D51, B34D51 EL (Janitrol) Beech 60, A60, B60 Duke 87D77-3 87D69-1 CD12010-1 B34D51, D34D5 1EL (Janitrol) Aerostar PA60-601P, 602P, 700P 87D77-3 87D69-1 CD12011-1 940 (SW), 99C42 (Janitrol) Lake LA-4, A, P, LA-4-200, 250 87D77-3 87D69-1 CD12012-1 37D77, 37D77-1EL (Janitrol) Piper PA-23, 23-235, 23-250, E23-25 87D77-3 87D69-1 CD12015-1 STC kit, heater SA02707CH Gulfstream G-44, G-44A 87D77-3 87D69-1 CD12016-1 mod kit rear heater Navion, A, B, C, D, E, F, G 87D77-3 87D69-1 CD12017-1 mod kit rear heater Navion, A, B, C, D, E, F, G 87D77-3 87D69-1 CD12018-1 mod kit rear heater Navion, A, B, C, D, E, F, G 87D77-3 87D69-1 CD12022-1 62D33, 1, 2 10E21-1, 2, 3, 4EL (Jan) Piper PA31T, 31T1 Chyenne 87D77-4 87D69-1 CD12030-1 mod kit heater DeHavillin DHC-2 87D77-4 87D69-1 CD12031-1 A39D59, C39D59EL (Janitrol) Piper PA31, 31-300, 31-325, 31-350 87D77-3 87D69-1 CD12032-1 39D59, B39D59, D39D59EL (Jan) Piper PA31, 31-325 87D77-3 87D69-1 CD12036-1 45D70, 45D70-1, -2EL (Janitrol) Piper PA-23, 23-235, 23-250, E23-25 87D77-3 87D69-1 CD12039-1 47D65, 47D65-1, -2, -3EL (Janitrol) Piper PA31P 87D77-3 87D69-1 CD12043-1 C15C54 (Janitrol) Twin Commander 500, 520, 560, 680 87D77-3 87D69-1 CD12044-1 62D95-1 (Janitrol) Twin Commander 500-S 87D77-3 87D69-1 CD12059-1 82D31-1, -2, 90D38-1EL (Janitrol) Piper PA34-200, 200T, 220T 87D77-1 87D69-1 CD12060-1 90D38-2EL (Janitrol) Piper PA44-180, 180T 87D77-3 87D69-1 CD12061-1 96C62, 96C62-1 (Janitrol) Cessna 310, T310, 320 87D77-3 87D69-1 CD12064-1 8240E (South Wind) Cessna 310Q, T310Q 87D77-3 87D69-1 CD12065-1 8240A, C (South Wind) Cessna 310, 320, Beech D18S 87D77-3 87D69-1 CD12089-1 20D35-1EL, 96C92-X (Janitrol) Lake LA-4, A, P, LA-4-200, 250 87D77-3 87D69-1 CD12090-1 20D35 (Janitrol) Piper PA30, PA-39 87D77-3 87D69-1 CD12091-1 mod kit heater Cessna 190, 195, 195A, 195B 87D77-4 87D69-1 CD12099-1 39D90, 39D90-1EL (Janitrol) Bell 206L 87D77-1 87D69-1 CD12188-1 91E88-1(IS), 90D39-2 (Janitrol) Piper PA44-180 87D77-3 87D69-1 CD12189-1 91E88-1(IS) (Janitrol) Piper PA34-220T 87D77-1 87D69-1 CD14010-1 94DB24, 978 (South Wind) Cessna 310, 310A 87D77-3 87D69-1 CD14019-1 07E94-1(EL) (Janitrol) Beech 76 87D76-6 87D78-4 TABLE 1 Heater Original New New Part number Heater Aircraft Lower Upper Rev. New: March 02/18 SL 060 © 2018 - Hartzell Engine Technologies. - All rights reserved Page 10 of 10 Service Letter Service Letter No. 060 CD Series Combustion Heater Fuel Shroud & Hardware Supersedure Heater Part No. Orig Heater Aircraft New Lower New Upper CD14020-1 07E94-2(EL) (Janitrol) Beech 76 87D76-6 87D78-4 CD14025-1 A34D35(EL) (Janitrol) Cessna 414, 421, 421A, 421B 87D77-3 87D69-1 CD14026-1 02E17-1, 13E55-1(EL) (Janitrol) Cessna 414, 414A, 421C 87D77-4 87D69-1 CD14027-1 02E17-2, 13E55-2(EL) (Janitrol) Cessna 340A 87D77-4 87D69-1 CD14028-1 02E17-2, 13E55-2(EL) (Janitrol) Cessna 340A 87D77-4 87D69-1 CD14048-1 65D79, -1, -2, -3EL (Janitrol) Piper PA31-350 87D77-3 87D69-1 CD14050-1 D83A28, F83A28 (Janitrol) Beech 95 series 87D76-6 87D78-4 CD14060-1 C83A28, E83A28 (Janitrol) Beech 50 series 87D77-3 87D69-1 CD14066-1 8259A, DL, FL, FL1 (South Wind) Cessna 411, 411A 87D77-3 87D69-1 CD14070-1 8259L (South Wind) Britten Norman BN-2 series 87D77-2 87D69-1 CD14071-1 8259GL, GL1, GL2, HL1, HL2 (SW) Cessna 401, A, B, 402, A, B, C, 404 87D77-3 87D69-1 CD14072-1 8259HR (South Wind) Cessna 310R, T310R 87D77-3 87D69-1 CD14073-1 8259JR2 (South Wind) Cessna 310R, T310R 87D77-3 87D69-1 CD14075-1 8259M (South Wind) Cessna 335 87D77-3 87D69-1 CD14077-1 8472D (South Wind) Cessna 340, 340A 87D77-3 87D69-1 CD14078-1 8472C, 8472E (South Wind) Cessna 414, 421B, 421C 87D77-3 87D69-1 CD14125-1 82D20 -1, -2EL (Janitrol) Beech 58P, 58PA 87D77-4 87D69-1 CD14126-1 07E02-1(EL) (Janitrol) Beech 58P, 58PA 87D76-6 87D78-4 CD14152-1 19E69-1(EL) (Janitrol) Cessna T303 87D77-4 87D69-1 CD14186-1 94E11-1(EL) (Janitrol) Britten Norman BN-2, 2A, 2A-6, 2A-8 87D77-4 87D69-1 CD14190-1 90E00-1(EL) (Janitrol), mod kit BN Group BN-2T, Beech 99, A, B 87D77-4 87D69-1 CD14192-1 81D94-1, -2, -3 EL (Janitrol) Beech 95, 55, 58, 58TC 81151 87D78-1 CD14193-1 81D94-1, -2, -3 EL (Janitrol) Beech 95, 55, 58, 58TC 87D76-6 87D78-4 CD50000-1 STC mod kit SA02816CH Beech G58 81151 87D78-1 CD52000-1 91E88-1(IS) (Janitrol) Piper PA34-220T 87D77-3 87D69-1 CD52001-1 90D38-2EL (Janitrol) Piper PA44-180, 180T 87D77-3 87D69-1 CD52002-1 90D38-2EL (Janitrol) Piper PA44-180, 180T 87D77-3 87D69-1 Heater Original New New Part number Heater Aircraft Lower Upper TABLE 1 (Cont’d)