Tube Mount NSA Sunvisor System

Rosen Sunvisor Systems LLC Data 9051-0171-001 Rev D Page 4 of 12 Company Proprietary Information. This document may not be disclosed without the permission of RSS Rosen Sunvisor Systems CMM / IPC for Sunvisor Assembly (p/n R1710000) Installation Instructions and ICA . Install time: approximately 1/2 to 1 hour. Please read these short instructions COMPLETELY before starting. Installation Hardware (included) Qty: (1) 1/16 Allen Key for #6-32 Set Screw Qty: (1) 7/64 Allen Key for #6-32 Cap Screw Qty: (1) 9/64 Allen Key for #8-32 Cap Screw Qty: (1) 5/32 Allen Key for #10-32 Cap Screw Qty: (1) MS16995-28B #8-32 x 3/4 Socket Head Cap Screw Qty: (1) 8HCLW #8 Lock Washer Qty: (1) AN565-AC6-4B #6-32 X 1/4 Cone Point Set Screw 1. Remove (2) stock visors (as necessary). 2. Remove the 4 screws and lock washers from clamp assembly. Position top clamp half on diagonal tube just down and below the corner and any soft goods or cross tube. Consideration should be made for side window coverage as well as the front windscreen. The bottom of the visor must clear the instrument glare-shield. 3. Attach BOTTOM CLAMP HALF using the same 4 screws and lock washers. Do not tighten at this point. 4. Rotate clamp on tube until the TAB on BOTTOM CLAMP HALF is as near to vertical* as possible. Tighten the 4 clamp screws evenly. 5. Mount the visor on the clamp TAB by installing the #8-32 x 3/4” SCREW and #8 LOCK WASHER. Position the joint so the visor SWING AXIS is vertical*. See example installations on a Maule and Husky on pages 2 & 3, respectively. *In normal horizontal flight Rosen Sunvisor Systems LLC Data 9051-0171-001 Rev D Page 5 of 12 Company Proprietary Information. This document may not be disclosed without the permission of RSS Rosen Sunvisor Systems CMM / IPC for Sunvisor Assembly (p/n R1710000) 6. Tighten the 8-32 x 3/4 SCREW 7. Tighten the #6-32 x 1/4 CONE POINT SET SCREW. The cone of the set screw will drive into the tab – locking it in place. 8. Repeat for the other side (if applicable). 9. Installation is now complete. Proceed to adjust the visor tension in the next section. Removal Removal is a reverse of installation. Visor Tension Adjustments: The three pivots of the Rosen NSA System are independently adjustable with the provided Hex Keys. Adjust the tension in each axis to your preference. All motions should be smooth, but not loose. The thumb screw on the VISOR EXTENSION ADJUSTMENT will allow you to make adjustments at anytime. To stow, the unit can be rotated straight to the overhead while in front, or moved to the side of the aircraft and rotated overhead. While in the forward position the NSA visor stows nicely overhead. Place the FAA STC and AML (if appropriate) in the Aircraft Maintenance Log and make an installation entry. Rosen Sunvisor Systems LLC Data 9051-0171-001 Rev D Page 6 of 12 Company Proprietary Information. This document may not be disclosed without the permission of RSS Rosen Sunvisor Systems CMM / IPC for Sunvisor Assembly (p/n R1710000) Continued Airworthiness Instructions:  (On the ground only) o Periodically clean the lenses with a soft cloth using Rosen Plastic Cleaner, Polisher and Protectant, or mild soap and water. Do not use abrasives on the lens. o Periodically adjust the pivot tensions on the visor assemblies. o Periodically (at minimum on annual inspections) inspect attaching hardware for security.  Updates to this continued airworthiness section are available on the Rosen Website. (www.rosenvisor.com) The most up to date version of this document is available on the Rosen Website. (www.rosenvisor.com) We recommend that you periodically look to make sure you are using the most current version. Airworthiness Limitations: The Airworthiness Limitations Section is FAA approved and specifies maintenance required under §§43.16 and 91.403 of the Federal Aviation Regulations unless an alternative program has been FAA approved. There are no airworthiness limitations associated with this installation. Rosen Sunvisor Systems LLC Data 9051-0171-001 Rev D Page 7 of 12 Company Proprietary Information. This document may not be disclosed without the permission of RSS Rosen Sunvisor Systems CMM / IPC for Sunvisor Assembly (p/n R1710000) Maule Installation Example: Image showing measurement from corner soft goods Completed Maule Installation Rosen Sunvisor Systems LLC Data 9051-0171-001 Rev D Page 8 of 12 Company Proprietary Information. This document may not be disclosed without the permission of RSS Rosen Sunvisor Systems CMM / IPC for Sunvisor Assembly (p/n R1710000) Husky Installation Example: Image showing measurement from cross tube. Husky Completed Installation: Side window coverage. Rosen Sunvisor Systems LLC Data 9051-0171-001 Rev D Page 9 of 12 Company Proprietary Information. This document may not be disclosed without the permission of RSS Rosen Sunvisor Systems CMM / IPC for Sunvisor Assembly (p/n R1710000) Figure 1 Rosen Sunvisor Systems LLC Data 9051-0171-001 Rev D Page 10 of 12 Figure 2 Company Proprietary Information. This document may not be disclosed without the permission of RSS Rosen Sunvisor Systems CMM / IPC for Sunvisor Assembly (p/n R1710000) Part Listing Figure No Figure Item Part Number Description Reference Eff QTY 1 R1710000-011 Complete Tube Mount System, ¾” Mount and Universal Lens System 1 R1710000-114 Tube Mount Visor Assembly, Pilot Side, ¾” Mount and Husky Lens (not shown) System 1 R1710000-034 Complete Tube Mount System, 5/8” Mount and Husky Lens (not shown) System 1 R1710000-134 Tube Mount Visor Assembly, Pilot Side, 5/8” Mount and Husky Lens (not shown) System 1 R1710000-041 Complete Tube Mount System, 7/8” Mount and Universal Lens System R1710200-114 Husky Visor Assembly, Pilot Side Only, ¾” Mount and Husky Lens (not shown) System 1 1 1710201 1710202 Lens, Universal Lens, Maule 1(pilot assy) 2 (system) 1 2 1710100-x Mounting Assembly 1(pilot assy) 2 (system) 1 3 1010000-5 Slide Assembly 1(pilot assy) 2 (system) 1 4 1020100-001 Mod Block Assembly 1(pilot assy) 2 (system) 1 5 1010003 Lens Strip 1(pilot assy) 2 (system) 1 6 8HCLW #8 High Collar Lock Washer 3(pilot assy) 6 (system) 1 7 MS16995-28B #8-32 X .750 Hexagon Socket Cap Screw(Black) 2(pilot assy) 4(system) 1 8 AN565-AC6-4B #6-32 x.25 Set Screw (Cone Point) 1(pilot assy) 2 (system) 1 9 1710102 Tube Mount - Swivel 1(pilot assy) 2 (system) 1 10 MS16995-27B #8-32 x.625 Hexagon Socket Cap Screw (Black) 1(pilot assy) 2 (system) Rosen Sunvisor Systems LLC Data 9051-0171-001 Rev D Page 11 of 12 Company Proprietary Information. This document may not be disclosed without the permission of RSS Rosen Sunvisor Systems CMM / IPC for Sunvisor Assembly (p/n R1710000) Rosen Sunvisor Systems LLC Data 9051-0171-001 Rev D Page 12 of 12 Company Proprietary Information. This document may not be disclosed without the permission of RSS 1 11 MS24693- C48BP #8-32 x.375 Phillips Flathead Screw 100 (Black/Patch) 3(pilot assy) 6(system) 2 1710100-x Mounting Assembly 1(pilot assy) 2 (system) 2 1 1710103-x Tube Mount - Bottom 1(pilot assy) 2 (system) 2 2 1710104 Tube Mount - Top 1(pilot assy) 2 (system) 2 3 6HCLW #6 High Collar Lock Washer 2(pilot assy) 4(system) 2 4 MS16995-20B #6-32 x .75 Hexagon Socket Head Cap Screw 2(pilot assy) 4(system)