Globe Engineering Specification Master List

AMS2801 D Heat Treatment of Titanium Alloy Parts AMS2807 C Identification Carbon and Low-Alloy Steels, Corrosion and Heat-Resistant Steels and Alloys Sheet, Strip, Plate and Aircraft Tubing AMS2816 W Reaffirmed 2025 Identification Welding Wire, Tab Marking Method AMS3025 E Polyalkylene Glycol Heat Treat Quenchant AMS3100 E Adhesion Promoter For Polysulfide Sealing Compounds AMS3195 H Silicone Rubber Sponge Closed Cell, Medium AMS3265 F Sealing Compound, Polysulfide Rubber, Fuel Resistant. . . AMS3276 H Sealing Compound, Integral Fuel Tanks and General Purpose, Intermittent Use to 360 °F (182 °C) AMS3277 L Sealing Compound…. AMS3281 G Sealing Compound, Polysulfide Synthetic Rubber AMS3304 J Elastomer: Silicone, Rubber (MQ/VMQ) General Purpose 65- 75 Durometer Type A Hardness AMS3315 G Silicone (VMQ) Rubber Sheet, Glass Cloth Reinforced AMS3410 K Flux, Silver Brazing AMS3411 E Flux, Silver Brazing High Temperature AMS3819 E Cloths, Cleaning for Aircraft Primary and Secondary Structural Surfaces AMS4006 K CANCELLED Superseded by ASTM B 209 Aluminum Alloy, Sheet and Plate 1.25 Mn - 0.12 Cu (3003-0) Annealed AMS4015 N Aluminum Alloy, Sheet and Plate (5052-0) Annealed AMS4016 N Aluminum Alloy, Sheet and Plate 2.5Mg - 0.25Cr (5052-H32) Strain Hardened, Quarter-Hard, and Stabilized (Composition similar to UNS A95052) AMS4025 P Aluminum Alloy, Sheet & Plate. . . AMS4026 N Aluminum Alloy, Sheet & Plate. . . AMS4027 P Aluminum Alloy, Sheet & Plate. . . AMS4031 K Aluminum Alloy, Sheet and Plate (2219-O) AMS4035 N Aluminum Alloy, Sheet And Plate (2024-0) AMS4036 L Aluminum Alloy Sheet and Plate, Alclad One Side 4.4CU - 1.5Mg - 0.60Mn Alclad One Side 2024 and 1-1/2% Alclad Once Side 2024-T3 Sheet; 1-1/2" Alclad One Side 2024-T351 Plate AMS4037 R Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024; -T3 Flat Sheet, -T351 Plate) Solution Heat Treated AMS4044 P Aluminum Alloy, Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr Annealed (7075-0) AMS4045 M Aluminum Alloy Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr 7075: (-T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated AMS4048 R Aluminum Alloy Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075-0) Annealed AMS4049 N Aluminum Alloy, Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075; -T6 Sheet - T651 Plate) Solution and Precipitation Heat Treated AMS4050 K Aluminum Alloy, Plate…… AMS4068 G Aluminum Alloy, Tube (2219-T3511) AMS4070 P Aluminum Alloy Tubing, Seamless, Drawn, Round AMS4071 P Aluminum Alloy, Drawn, Round Seamless Hydraulic Tubing AMS4078 L Aluminum Alloy Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr 7075: (-T73 Sheet, T7351 Plate) Solution Heat Treated and Overaged (Composition similar to UNS A97075) AMS4079 J Aluminum Alloy, Drawn, Round, Seamless, Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Close Tolerance, Annealed AMS4080 R Aluminum Alloy, Drawn Seamless Tubing . . . AMS4081 K Aluminum Alloy, Hydraulic, Seamless Tubing AMS4082 S Aluminum Alloy Tubing, Seamless , Drawn AMS4083 N Aluminum Alloy Tubing, Hydraulic 6061-T6 AMS4088 L Aluminum Alloy, Drawn, Seamless Tubing (2024-T3) AMS4101 G Alluminum Alloy, Plate 4.4Cu - 1.5Mg - 0.60Mn (2124-T851) Solution Heat Treated, Stretched, and Precipitation Heat Treated AMS4114 J CANCELLED AMS4115 K Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and wire and Flash Welded Rings Annealed 1.0Mg - 0.60Si - 0.28 AMS4116 K Aluminum Alloy, Bars, Rods & Wire (6061-T4) AMS4117 L Aluminum Alloy, rolled or Cold Finished Bars, Rods, and wire and Flash Welded Rings…. (6061;-T6, -T651) Solution and Precipitation Heat Treated AMS4150 P Aluminum Alloy, Extrusions and Rings…. AMS4161 K Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged (Composition Similar to UNS A96061) AMS4173 G Alluminum Alloy, Extrusions 1.0Mg-0.60Si-0.30Cu-0.20Cr (6061-T6511 or T6510) Solution Heat Treated, Stress Relieved by Stretching, Straightened and Precipitaion Heat Treated AMS4182 J Aluminum Alloy, Wire 5.0Mg - 0.12Mn - 0.12Cr (5056-0) Annealed AMS4189 K Aluminum Alloy Welding Wire 4.1 Si-0.20 Mg (4643) AMS4190 L Aluminum Alloy, Welding Wire 5.2 Si (4043) AMS4191 K Aluminum Alloy, Welding Wire AMS4201 H Aluminum Alloy Plate 6.2Zn - 2.3Cu - 2.2 Mg - 0.12Zr (7050-T7651) Solution Heat Treated, Stress Relieved and Overaged (Composition Similar to A97050) AMS4216 C Alum. Alloy Sheet (6013-T6) AMS4268 B Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn; (2024-T81 Sheet, -T851 Plate) Solution Heat Treated, Cold Worked and Artificially Aged AMS4274 C Aluminum Alloy, Alclad Sheet 4.4Cu - 1.5Mg - 0.60 Mn (Alclad 2024-0) Annealed, Fine Grain AMS4315 B Aluminum Alloy, Sheet and Plate. . . AMS4316 C Aluminum Alloy, Alclad Sheet and Plate. . . AMS4340 H Aluminum Alloy, Extrusions AMS4341 H Aluminum Alloy, Extrusions 6.2ZN - 2.3Cu - 2.2Mg - 0.12Zr (7050-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged AMS4342 G Aluminum Alloy, Extrusions 6.2ZN - 2.3Cu - 2.2Mg - 0.12Zr (7050-T74511) Solution Heat Treated, Stress Relieved, Straightened and Overaged AMS4347 E Aluminum Alloy Sheet (6013-T4) AMS4461 C Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024-O, Sheet and Plate) Annealed; or when specified, “As Fabricated” (2024-F) AMS4462 B Alluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024, -T3 Sheet, -T351 Plate) Solution Heat Treated, Cold Worked and Naturally Aged AMS4478 B Aluminum Alloy, Sheet and Plate, Alclad 4.4 Cu - 1.5MG - 0.60Mn (Alclad 2024, -T81 Sheet, T851 Plate) Solution Heat Treated, Cold Worked and Artificially Aged AMS4640 J Aluminum Bronze, Bars, Rods, Shapes, Tubes, and Forgings 81.5Cu-10.0Al-4.8Ni-3.0Fe Drawn and Stress Relieved (HR50) or Temper Annealed (TQ50) AMS4769 G Silver Alloy, Brazing Mat AMS4771 J Silver Alloy, Brazing Filler Metal . . . AMS4777 K Nickel Alloy, Brazing Filler Metal . . . AMS4900 S Titanium Sheet, Strip, and Plate Commercially Pure Annealed, 55 ksi (379 Mpa) Yield Strength (Composition similar to UNS R50550) AMS4901 V Titanium Sheet, Strip, and Plate Commercially Pure Annealed, 70.0 ksi (485 MPa) (Composition similar to UNS R50700) AMS4902 M Titanium Sheet, Strip, and Plate AMS4911 T Titanium Alloy, Sheet, Strip and Plate, 6Al-4V Annealed AMS4921 S Titanium Bars, Wire, Forgings and Rings. . . AMS4928 X Titanium Alloy Bars, Wire, Forgings, Flash-Welded Rings and Drawn Shapes, 6Al-4V Annealed AMS4940 D Titanium Sheet. . . AMS4941 H Titanium Tubing, Welded 40 ksi (276 MPa) Yield Strength AMS4942 H Titanium Tubing, Seamless Annealed. . . AMS4943 M Titanium Alloy, Hydraulic Seamless Tubing 3.0Al-2.5V Annealed AMS4944 N Titanium Alloy Tubing, Seamless, Hydraulic. . . AMS4945 J Titanium Alloy Tubing, Seamless, Hydraulic. . . AMS4951 K Titanium Wire, Welding AMS4954 L Titanium Alloy, Welding Wire 6Al-4V AMS4956 H Titanium Alloy Welding Wire 6Al - 4V, Extra Low Interstitial Environment Controlled Packaging (Composition Similar to UNS R556408) AMS5510 T Steel, Corrosion and Heat Resistant, Sheet. . . AMS5511 L Steel, Corrosion-Resistant, Sheet, Strip & Plate 19Cr-9.5Ni (304L) Solution Heat Treated AMS5512 N Steel, CHR, Sheet, Strip and Plate AMS5513 L Steel, Corrosion Resistant, Sheet, Strip, & Plate AMS5516 S Steel, Corrosion-Resistant, Sheet, Strip & Plate 18cR - 9.0Ni (302) Solution Heat Treated AMS5517 N Steel, Corrosion Resistant, Sheet and Strip. . . AMS5518 P Steel, Corrosion-Resistant, Sheet and Strip. . . AMS5519 R Steel, Corrosion-Resistant, Sheet and Strip. . . AMS5520 H Steel, Corrosion and Heat-Resistant, Sheet, Strip, Foil, and Plate 15Cr - 7.1Ni - 2.5Mo - 1.1Al Solution Heat Treated, Precipitation Hardenable AMS5524 N Steel, Corrosion & Heat Resistant, Sheet, Strip, and Plate AMS5525 L Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate AMS5528 K Steel, Corrosion Resistant, Sheet, Strip & Plate AMS5532 J Iron Alloy, Corrosion & Heat Resistant…. AMS5536 R Nickel Alloy, Corrosion and Heat Resistant, Sheet, Strip and Plate 47.5Ni - 22Cr - 1.5Co - 9.0Mo - 0.60W - 18.5Fe (Alloy X or HZ) Solution Heat Treated AMS5537 K Cobalt Alloy, Corrosion and Heat-Resistant, Sheet, Strip, Foil and Plate 52Co-20Cr-10Ni-15W (Solution Heat Treated) AMS5540 R Nickel Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 74 Ni - 15.5Cr - 8.0 Fe Annealed AMS5548 R Steel, Corrosion and Heat-Resistant, Sheet and Strip ….. AMS5556 K Steel, Corrosion and Heat-Resistant, Seamless or Welded Hydraulic Tubing 18Cr - 11Ni - 0.70Cb (SAE 30347) Solution Heat Treated AMS5557 K Steel, Corrosion & Heat Resistant, Seamless or Welded Hydraulic Tubing (T321) Solution HT AMS5560 P Steel, Corrosion Resistant, Seamless Tubing 19Cr-10Ni (SAE30304) Solution Heat Treated AMS5561 H Steel, Corrosion and Heat-Resistant AMS5564 D Steel, Corrosion Resistant, Tubing 19CR - 10Ni (SAE 30304) High-Pressure Hydraulic, Welded Plus Ultrasonically Tested or Seamless Cold Drawn, One Eighth - Hard Temper AMS5567 G Steel, Corrosion Resistant, Seamless or Welded Hydraulic Tubing 19Cr-10Ni (SAE 30304) AMS5568 J Steel, Corrosion & Heat-Resistant, Welded Tubing. . . AMS5570 R Steel, Corrosion & Heat-Resistant, Seamless…. AMS5576 M Steel, Corrosion & Heat-Resistant, Welded Tubing. . . AMS5581 G Nickel Alloy, Corr. & Heat Resist. Tubing AMS5596 N Heat Resistant Nickel Alloy AMS5599 J Nickel Alloy, Corr. & Heat Resist., Sheet, Strip & Plate AMS5604 K Steel, Corrosion Resistant, Sheet, Strip, and Plate 16.5Cr - 4.0Ni - 4.0Cu - 0.30Cb Solution Heat Treated, Precipitation Hardenable (Composition similar to UNS S17400)X AMS5612 L Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Mechanical Tubing, Rings and Stock for Forging and Flash- Welded Rings, 12Cr (4100, Ferrite Controlled, Annealed AMS5629 K Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings and Extrusions, 13Cr - 8.0Ni - 2.2 Mo -1.1Al Vacuum Induction Plus Consumable Electrode Melted, Premium Aircraft-Quality, Solution Heat Treated, Precipitation Hardenable AMS5639 K Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, Rings and Forging and Ring Stock 19Cr - 10Ni Solution Heat Treated AMS5640 W Steel, Corrosion-Resistant, Bar AMS5641 J Steel, Corrosion-Resistant, Bars, Wire, Forgings and Forging Stock 18.5Cr - 10Ni - 0.22Se (303Se) Free-Machining; for Swaging or Upsetting Solution Heat Treated AMS5643 W Steel, Corrosion-Resistant Bars, Wire, Forgings, Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb (Nb) - 4.0 Cu Solution Heat Treated, Precipitation Hardenable (Composition similar to UNS S17400) AMS5645 T Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Mechanical Tubing, Rings and Forging Stock…. AMS5646 R Steel Bars, Forging, Tubing, and Rings; Corrosion and Heat Resistant AMS5653 K Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Mechanical Tubing, Rings, and Stock for Forging and Rings 17Cr - 12Ni - 2.5Mo (0.030 Max C) (316L) Solution Heat Treated AMS5659 T Steel, Corrosion - Resistant, Bars….. AMS5662 P Nickel Alloy, Corrosion & Heat-Resistant ….. AMS5663 P Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, Rings and Stock for Forgings and Rings. . . AMS5666 K Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, Extrusions, Rings, and Stock for Forgings, Extrusions, and Rings 62Ni - 21.5Cr - 9.0Mo - 3.65Cb (Nb) Annealed AMS5678 G Steel, Corrosion Resistant, Wire 17Cr - 7.1 NI - 1.1AI Cold Drawn, Precipitaion-Hardenable AMS5680 K Steel, Corrosion & Heat Resistant, Welding Wire AMS5689 H Steel, Corrosion and Heat Resistant, Wire 18Cr - 10.5Ni - 0.40Ti (321) Solution Heat Treated AMS5731 M Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Mechanical Tubing, Rings or Heading 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Remelted, 1800 °F (982 °C) Solution Heat Treated AMS5737 R Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Mechanical Tubing. . . 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Remelted 1650 °F (899 °C) Solution and Precipitation Heat Treated AMS5743 L Steel, Corrosion & Heat Resistant, Bars, Forgings. . . AMS5774 F Steel, Corrosion & Heat-Resistant, Welding Wire. . . AMS5782 J Steel, Corrosion & Heat Resistant, Welding Wire 20.5Cr - 9.0Ni - 0.50Mo - 1.5W - 1.2Cb - 0.20Ti Vacuum induction Melted AMS5786 J Nickel Alloy, Corrosion & Heat Resistant Weld Wire AMS5794 G Iron Alloy, Corrosion & Heat Resistant, Welding Wire. . . Annealed AMS5798 J Nickel Alloy, Corrosion & Heat-Resistant ….. AMS5812 G Steel, Corrosion and Heat Resistant, Welding Wire 15Cr - 7.1Ni - 2.4Mo - 1.0Al Vacuum Induction Melted AMS5824 G Steel, Corrosion Resistant, Welding Wire AMS5825 J Steel, Corrosion-Resistant, Welding Wire 16.4Cr - 4.8Ni - 0.22Cb(Nb) - 3.6Cu AMS5826 F Steel, Corrosion & Heat Resistant, Welding Wire AMS5832 J Nickel Alloy, Corrosion and Heat Resistant, Welding Wire AMS5837 H Alloy Welding Wire, Corrosion & Heat Resistant AMS5839 D Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 59Ni - 22Cr - 2.0Mo - 14W - 0.35Al AMS5862 M Steel, Corrosion-Resistant, Sheet, Strip & Plate 15cR - 4.5Ni - 0.30Cb (Nb) - 3.5 Cu AMS5878 F Nickel Alloy, Corrosion and Heat Resistant, Sheet, Strip and Plate 59Ni - 22Cr - 2Mo - 14W - 0.35Al - 0.03La Solution Heat Treated AMS5896 C Steel, Corrosion and Heat-Resistant Seamless or Welded Hydraulic Tubing (T321) 1/8 Hard AMS5901 D Steel, Corrosion Resistant, Sheet, Strip, Plate AMS5951 B Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip and Plate. . . AMS6345 F Steel, Sheet, Strip, And Plate 0.95Cr – 0.20Mo AMS6348 F Steel, Bars Aircraft Quality (4130) Normalized AMS6350 R Steel Sheet, Strip and Plate 0.95Cr – 0.20Mo (SAE 4130) Aircraft Quality AMS6351 M Steel, Sheet, Strip and Plate 0.95Cr - 0.20Mo (SAE 4130) Aircraft Quality, Spheroidized AMS6360 R Steel Mechanical Tubing, Seamless. . . AMS6371 M Steel, Mechanical Tubing 0.94Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) AMS6373 K Steel, Welded Tubing 0.95Cr - 0.20Mo (0.28 - 0.33C) AMS6457 E Steel, Welding Wire AMS6461 L Steel Welding Wire AMS6462 K Steel Welding Wire AMS6931 D Titanium Alloy Bars, Forgings, and Forging Stock 6.0Al-4.0V Annealed AMS7490 R Reaffirmed 2025-09 Rings, Flash Welded Corrosion and Heat- Resistant Austenitic Steels, Austenitic-Type Iron, Nickel or Cobal Alloys, or Precipitation-Hardenable Alloys AMS8660 A Silicone Compound NATO Code Number S-736 AMS-A-8625 CANCELLED A Jul 2003 Use MIL-A-8625 AMS-C-26074 D CANCELLED Superseded by AMS2404 AMS-C-27725 E Coating, Corrosion Preventative Polyurethane.. AMS-C-5541 A CANCELLED Superseded by MIL-C-5541 AMS-C-6183 B Cork and Rubber Composition Sheet; for Aromatic Fuel and Oil Resistant Gaskets AMS-C-7438 A Core Material, Aluminum, for Sandwich Construction AMS-C-83231 A Coatings, Polyurethane, Rain Erosion Resistant for Exterior Aircraft and Missile Plastic Parts AMS-C-9084 2013-07 Reaffirmed 2022-10 Cloth, Glass, Finished, For Resin Laminates AMS-DTL-22499 B Shim Stock, Laminated AMS-DTL-22499/1 B SHIM STOCK, LAMINATED, ALUMINUM ALLOY AMS-DTL-23053/5 B CANCELLED Replaced by AS23053/5 AMS-DTL-23053/6 B CANCELLED Replaced by AS23053/6 AMS-DTL-23053/13 B CANCELLED Replaced by AS23053/13 AMS-H-6088 C CANCELLED See AMS2770 AMS-H-6875 C Heat Treatment of Steel Raw Materials AMS-H-81200 D Heat Treatment Of Titanium And Titanium Alloys AMS-I-7444 A Insulation Sleeving, Electrical, Flexible AMS-QQ-A-200 C Aluminum Alloy, Bar, Rod, Shapes, Structural Shapes, Tube, and Wire, Extruded: General Specification For AMS-QQ-A-200/11 A Aluminum Alloy 7075, Bar, Rod, Shapes, .... AMS-QQ-A-200/15 B Aluminum Alloy Bar, Rod, and Shapes, Extruded, 7075-T76 Improved Exfoliation Resistance AMS-QQ-A-200/2 B Aluminum Alloy 2014, Bar, Rod, Shapes, Tube, and Wire, Extruded AMS-QQ-A-200/3 A Aluminum Alloy 2024, Bar, Rod, Shapes, Tube and Wire Extruded AMS-QQ-A-200/8 A Aluminum Alloy 6061, Bar, Rod, Shapes, …. AMS-QQ-A-225 C Aluminum and Aluminum Alloy, Bar, Rod, Wire, or Special Shapes; Rolled, Drawn, or Cold Finished AMS-QQ-A-225/2 A CANCELLED Superseded by ASTM-B211 Aluminum Alloy 3003… AMS-QQ-A-225/4 A Aluminum Alloy, 2014, Bar, Rod, Wire and Special Shapes, Rolled, Drawn, or Cold Finished AMS-QQ-A-225/6 B Aluminum Alloy, 2024, Bar, Rod, Wire…. AMS-QQ-A-225/8 B CANCELLED Superseded by AMS4115, AMS4116, AMS4128, AMS4117, AMS4115, AMS4116, AMS4117 Alum Alloy 6061, Bar, Rod, Wire…. AMS-QQ-A-225/9 A Aluminum Alloy 7075, Bar, Rod, Wire, and Special Shapes; Rolled, Drawn, or Cold Finished AMS-QQ-A-250 B Alum & Alum Alloy, Plate and Sheet AMS-QQ-A-250/1 A CANCELLED Superseded by ASTM B 209 Aluminum 1100, Plate and Sheet AMS-QQ-A-250/11 A CANCELLED Superseded by AMS4025,AMS4026,AMS4027,ASTM-B209 Aluminum Alloy 6061, Plate and Sheet AMS-QQ-A-250/12 A Aluminum Alloy 7075, Plate and Sheet AMS-QQ-A-250/13 AUG 1997 CANCELLED Superseded by AMS4048 Aluminum Alloy Alclad 7075, Plate and Sheet AMS-QQ-A-250/2 A Aluminum Alloy 3003, Plate and Sheet AMS-QQ-A-250/24 B CANCELLED Superseded by AMS4315 Alum Alloy 7075, Plate, Sheet AMS-QQ-A-250/25 B CANCELLED Superseded by AMS4316 Aluminum Alloy, Alclad 7075 AMS-QQ-A-250/29 A Aluminum Alloy 2124, Plate AMS-QQ-A-250/3 A Aluminum Alloy Alclad 2014, Plate and Sheet AMS-QQ-A-250/30 A Aluminum Alloy 2219, Plate and Sheet AMS-QQ-A-250/4 B Aluminum Alloy 2024, Plate and Sheet AMS-QQ-A-250/5 C Aluminum Alloy Alclad 2024, Plate and Sheet AMS-QQ-A-250/8 C Aluminum Alloy 5052, Plate and Sheet AMS-QQ-P-35 A CANCELLED Superseded by AMS2700 AMS-QQ-P-416 G Plating, Cadmium (Electrodeposited) AMS-QQ-S-763 D Steel Bars, Wire, Shapes, and Forgings; CRS AMS-S-13165 A CANCELLED Superseded by AMS2430 Shot Peening of Metal Parts AMS-S-6758 B Steel, Chrome-Molybdenum (4130) Bars …. AMS-S-8802 F Sealing Compound, Fuel Resistant, Integral Fuel Tanks and Fuel Cell Cavities AMS-S-8840 A Steel Sheet and Strip, Corrosion-Resistant, Precipitation Hardening (AM350 & AM355)… AMS-STD-595 A AMD1,2,3 Colors Used in Government Procurement AMS-STD-753 B Corrosion-Resistant Steel Parts: Sampling, Inspection and Testing for Surface Passivation AMS-STD-1595 A CANCELLED Superseded by AWS D17.1 AMS-STD-2154 E Inspection, Ultrasonic, Wrought Metals, Process AMS-STD-2175 A Superseded by AMS2175 AMS-STD-2219 A CANCELLED Superseded by AWS D17.1 Fusion Welding for Aerospace Application AMS-T-6736 B CANCELLED Superseded by SAE-AMS-6360,6361,6362 AMS-T-6841 A Tape and Sheet, Adhesive, Rubber and Cork Composition AMS-T-6845 B Tubing, Steel, Corrosion-Resistant S30400 1/8 H AMS-T-7081 A CANCELLED Superseded by AMS4081 or AMS4083 Tube, Alum. Alloy, Seamless..Hydraulic… AMS-T-81914/2 CANCELLED Superseded by AS81914/2 Tubing, Plastic, Extra Flexible, Convoluted, Polytetrafluoroethylene Close Convolution AMS-T-9046 B CANCELLED See NOTICE for supersession AMS-T-9047 A CANCELLED See NOTICE for supersession AMS-W-6858 A CANCELLED Superseded by AWS D17.2 Welding, Resistance: Spot and Seam AMS-WW-T-700/2 A CANCELLED Superseded by ASTM-B210 Tube, Aluminum, Alloy, Drawn, Seamless, 3003 AMS-WW-T-700/3 B Tube, Aluminum Alloy, Drawn, Seamless 2024 AMS-WW-T-700/4 B Tube, Aluminum Alloy, Drawn, Seamless 5052 AMS-WW-T-700/6 C Tube, Aluminum Alloy, Drawn, Seamless 6061 AMS-WW-T-700/7 B Tube, Aluminum Alloy, Drawn, Seamless 7075 Aerospace Recommended Practice ARP584 D Coiled Tubing - Corrosion Resistant Steel, Hydraulic Applications, Aerospace ARP994 C Design of Tubing Installations for Aerospace Hydraulic Systems ARP1176 B Reaffirmed 2025-09 Oxygen System & Component Cleaning and Packaging ARP1234 F Static Axial O-Ring Seal Aplications without Anti-Extrusion Devices for Engine and Engine Control Systems ARP1917 B CANCELLED Superseded by AS7766 ARP1962 C Training and Approval of Thermal Processing Personnel ARP4146 D Coiled Tubing - Titanium Alloy, Hydraulic Applications, Aerospace ARP4988 A Procedure for Determining Thrust Wire Lengths and Minimum Insertion Depths ARP8615 NC 2011-08 Fuel System Components: General Specification for ARP9136 NC 2016-11 Aerospace Series - Root Cause Analysis and Problem Solving (9S Methodology) Aerospace Standard (AS) AS1038 H Fitting, Elbow, 90 Degree, Standard and Reducer, Bulkhead, Flared AS1039 H (R) Fitting, Tee, Standard and Reducer, Bulkhead on Side, Flared AS1043 H Safety Wire Holes, Hex, Fitting, Location of, Design Standard AS1072 F Sleeve, Hose Assembly, Fire Protection AS1097 B Seal Ring, 37 Degree Flared Tube Fitting End AS1098 B Fitting End Standard Dimensions, 37 Degree Flared Tube Connection for Seal Ring AS1182 E Standard Stock Removal Allowance Aircraft-Quality and Premium Aircraft-Quality Steel Bars and Mechanical Tubing AS123601 thru AS13750 C Rivet, Solid, 100° Flush Head, Nickel Alloy UNS N06600 AS13000 A Problem Solving Requirements for Suppliers AS13001 A Supplier Self Release Training Requirements AS13002 2015-03 Requirements for Developing and Qualifying Alternate Inspection Frequency Plans AS13003 A Measurement Systems Analysis Requirements for the Aero Engine Supply Chain AS13004 A Process Failure Mode and Effects Analysis (PFMEA) and Control Plans AS13006 A Process Control Methods AS13100 A AESQ Quality Management System Requirements for Aero Engine Design and Production Organizations AS14101 E Boeing Supp C Bearing, Plain, Self-Lubricating, Self-Aligning, Low Speed, Narrow, Grooved Race, -65 to +325 °F AS14103 F Bearing, Plain, Self-Lubricating, Self-Aligning, Self-Aligning, Low Speed, Wide, Grooved Race, -65 to +325 °F AS14238 E Bushing, Sleeve Flanged, Press Fit, Ream Type AS1424 H Hose Assemblies, Metal, Medium Pressure, High Temperature AS1576 G Fittings, Welded, Hydraulic, Titanium, Corrosion-Resistant Steel and Nickel, 3000 psi Hydraulic AS1577 B Tube End, Weld Design Standard AS1581 E Boeing Supp P Fitting, Sleeve, Flareless, Acorn to Integral Welding Ring, 3000 PSI AS1582 H Boeing Supp T Fitting, Adapter, External Thread Flareless to Integral Weld Ring, 3000 PSI AS1650 F Coupling Assembly, Threadless, Flexible, Fixed Cavity, Self- Bonding, Procurement Specification AS1653 D Male Ferrule, Threadless … AS1654 E Sleeve, Threadless … AS1656 D Fitting End, Threadless …… AS1716 E Boeing Supp C Ferrule, Coupling, Flexible…. AS1719 C Fitting End, Half-Coupling, Flexible Variable Cavity Threaded, Ferrule Type Design Standard AS1732 F Body, Coupling, Rigid, Fixed Cavity, Threaded, Ferrule Type Tube Ends, Type II AS1733 F Body, Coupling, Rigid, Fixed Cavity, Threaded, Ferrule Type Tube Ends, Type I AS1734 D Nut, Coupling, Rigid, Fixed Cavity, Threaded, Ferrule Type Tube Ends, Type I AS1736 D Washer, Coupling, Rigid, Fixed Cavity, Threaded, Ferrule Type Tube Ends AS1737 C Ferrule, Coupling, Rigid, Fixed Cavity Threaded, Ferrule Type Tube Ends AS1790 H Nut, Retained, Lightweight AS1791 E Wire, Retainer - Tube Coupling Nut AS1792 E Nut, Fitting, Lightweight, Flareless AS18280 H Fittings, 24° Cone Flareless, Fluid Connection, 3000 psi AS18280/1 C Sleeve, Bite Type, 24°Cone Flareless Fitting, 3000 psi AS1895 F Coupling Assembly, V-Retainer, High Pressure High Temperature, Pneumatic Tube AS1895/5 D Flange, Male, Seam Weld, Type II Low Profile AS1895/6 D Flange, Female, Seam Weld, Type II Low Profile AS1895/8 E Flange, Male, Butt Weld, Type II Low Profile AS1895/8SUP K Flange, Male, Butt Weld, Type II Low Profile AS1895/9 D Flange, Female, Butt Weld, Type II Low Profile AS1895/9SUP L Flange, Female, Butt Weld, Type II Low Profile AS1895/13 E Flange End, Femail, Type I Standard Profile Design Standard AS1895/14 D Flange End, Male, Type II Low Profile Design Standard AS1895/15 E Flange End, Female, Type II Low Profile Design Standard AS1895/16 B Flange, Male, Integral, Weld Ring, Type II Low Profile AS1960 A Coupling Assembly, V-Band, Sheet Metal Flange, Pneumatic Tube AS1960/3 A Flange, Sheet Metal AS2094 B Test Methods for Tube-Fitting Assemblies AS20253 B Pin, Hinge, Corrosion resistant Steel UNS S30200, UNS S30400 or UNS S31600 AS21902 D Boeing Supp G Union, Flareless Tube AS21915 D Boeing Supp F Adapter, Straight, Tube to Boss AS21916 H Reducer, External Thread, Flareless Tube AS21916SUP G Reducer, External Thread, Flareless Tube AS21921 D Nut, Sleeve Coupling, Flareless AS21921SUP C Nut, Sleeve Coupling, Flareless AS21922 C Sleeve, Coupling, Flareless AS21922SUP D Sleeve, Coupling, Flareless AS23053/5 A Insulation Sleeveing, Electrical, Heat Shrinkable, Polyolefin, Flexible, Crosslinked AS23053/6 2016-10 Reaffirmed 2022-01 Insulation Sleeveing, Electrical, Heat Shrinkable, Polyolefin, Semi-Rigid, Crosslinked AS23053/13 2016-10 Reaffirmed 2022-01 Insulation Sleeveing, Electrical, Heat Shrinkable, Fluoroelastomer, Flexible AS24563 B Flange Profiles, V-Coupling AS28778 C O-Ring, Straight Thread Tube Fitting Boss Molded from AMS-P-5510 Rubber AS29512 C Hydrocarbon Fuel Resistant, Tube Fitting, O-Ring Molded From AMS-P-5315 Rubber AS29513 C Boeing Supp F Packing, Preformed, Hydrocarbon Fuel Resistant, "O" Ring AS3071 C Acceptance Criteria-Magnetic Particle, Fluorescent Penetrant, and Contrast Dye Penetrant Inspection AS3208 A Stabilized 2020 - USE AS83248/1 FOR HYDRAULIC AND PNEUMATIC APPLICATIONS AS3220 B Fitting, Sleeve, Flared Aluminum AS33514 E Fitting End, Standard Dimensions for Flareless Tube Connection and Gasket Seal AS33515 D Fitting End, Standard Dimensions for Bulkhead Flareless Tube Connections AS33566 2000-09 Reaffirmed 2013-01 Fittings, Installation of Flareless Tube, Straight-Threaded Connectors AS33583 1997-12 (R2015-04) Tubing End Double Flared AS33611 1997-08 (R2015-04) Boeing Supp A Tube Bend Radii AS33649 A CANCELLED Superseded by AS5202 Bosses, Fluid Connection, Internal Straight Thread AS3581 A Boeing Supp B Packing Preformed - O Ring AS3582 1996-09 (2018-08) Packing, Preformed - O-Ring Seal AMS3304 AS38386/2 A Connector, Air Duct Hose, Ground Cooling, Female AS4059 G Contamination Classification for Hydraulic Fluids AS4060 1995-09 (R2013-01) Tube Fitting Swaged Joint, Roller Expander Manual Process AS4208 A Fitting End, Bulkhead, External Thread, Beam Seal, Design Standard AS4209 E Fitting End Assembly, Internal Thread, Retained Nut, Beam Seal, Design Standard AS4227 D Fitting Assembly, Adapter, Internal Thread, Beam Seal to Integral Weld Ring AS4228 D Fitting, Adapter, External Thread, Beam Seal to Integral Weld Ring AS4229 C Fitting, Adapter, Bulkhead, External Thread, Beam Seal To Integral weld Ring AS4330 A Tubing, Flared AS4357 B Hose Assembly, Polytetrafluoroethylene, Cres Reinforced, 400° F, 3000 PSI, Heavyweight, Beam Seal, 90° to 90° AS4370 G Nut, Fitting, Retained AS4375 D Fitting End, Flareless Design Standard AS4395 C Fitting End, Flared, Tube Connection….. AS4396 C Fitting End, Bulkhead, Flared Tube Connection AS4407 D Fitting Assembly, Elbows 90°, Reducer and Nonreducer, Internal Flare to Flared Tube AS4458 B Fitting End, Flareless, Blunt Nose, Design Standard AS4510 A Fittings, Weld, Fluid Connection, 5000 psi Maximum AS4697 C Fitting End, Integral Centered Weld Lip, Design Standard AS4734 D Male Ferrule, Threadless - Flexible, Fixed.... AS4736 A (R2013-01) Female Ferrule, Threadless - Flexible Fixed… AS478 S Identification Marking Methods AS4841 D Fittings, 37 Degree Internal Flare, Fluid Connection, Procurement Specification AS4873 A Gland Design, Elastomeric O-Ring Seals, Static Radial and Face 800 psi Maximum Service AS4875 B Fittings, Straight Threaded Boss or Flanged, Fluid Connection AS5127 D Methods for Testing Aerospace Sealants AS5127/1 D Aerospace Standard Test Method for Aerospace Sealants AS5131 A Tube End - Beaded AS5132 1997-01 (R2015-04) Fitting End - Hose Connection, Design Standard AS5148 A Assembly, Installation and Torque for Flareless and Straight Thread Fluid Fitting and Tube Assemblies AS5168 D Fitting, Plug, Tube End, Flared AS5169 D Fitting, Port Plug and Bleeder AS5173 E Fitting, Bushing, Port, Reducer AS5174 F Boeing Supp D Fitting, Union and Reducer, Flared AS5175 A Nut, Coupling, Flared AS5176 D Boeing Supp C Boeing SL Supp 30M-AS5176(A) Fitting, Sleeve, Flared AS5178 E Boeing Supp F Boeing SL Supp 30M-AS5178(C) Nut, Fitting, Bulkhead AS5184 2004-07 (R2015-04) Fitting, Adapter, Flared to Hose AS5192 F Fitting, Tee, Internal Straight Thread Port AS5200 2004-07 (R2013-01) Port or Fitting End, Internal Taper Pipe Thread, Design Standard AS5202 A Port Or Fitting End, Internal Straight Thread, Design Std. AS5205 B Nut, Fitting, Engine, Flared AS5227 A Flange, Straight Thread Port, Weld AS5231 C Fitting, Plug, Tube End, Flareless AS5235 C Fitting, Sleeve, Couplings, Flareless AS5272 G Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting, Procurement Specification AS5406 D Fitting, Union, Tube, .375 Bulkhead AS5502 F Standard Requirements for Aerospace Sealants AS5528 F Lubricant Application, Solid Film, Heat Cured, Corrosion Inhibiting AS5553 E Counterfeit Electronic Parts, Avoidance, Detection, Mitigation and Disposition AS5620 C Titanium Hydraulic Tubing, Ti-3Al-2.5V Cold Worked and Stress Relieved. . . . AS568 F Aerospace Size Standard for O-rings. AS5791 B Fitting Assembly, Adapter, Bulkhead Flareless, Axially Swaged, Hydraulic AS5792 D Fitting Assembly, Straight, Female Flareless, Axially Swaged, Hydraulic AS5793 B Fitting Assembly, Straight, Male Flareless, Axially Swaged, Hydraulic AS5801 B Fitting Assembly, 90° Female Flareless, Axially Swaged, Hydraulic, 3000 PSI AS5802 B Fitting Assembly, 90°, Male Flareless, Axially Swaged, Hydraulic, 3000 PSI AS5803 B Fitting Assembly, 45° Elbow, Female Flareless, Axially Swaged, hydraulic, 3000 PSI AS5827 A Fitting End, Flareless…. AS5836 2006-09 (R2013-01) Fitting End, Threadless-Flexible, Fixed Cavity, Current Carrying, Self Bonding, Male and Female Design Standard AS5837 2013-01 Male Ferrule, Threadless-Flexible, Fixed Cavity, Current Carrying, Self Bonding, Butt Welded AS6174 B Counterfeit Materiel; Assuring Acquisition of and Conforming Materiel. AS6279 C Standard Practice for Production, Distribution and Procurement of Metal Stock AS7101 C NADCAP General Reqs. for Mats Test Laboratory Accreditation Program AS71051 B Pipe Threads, taper, Aeronautical National Form, Symbol ANPT - Design and Inspection Standard AS7116 A CANCELLED Superseded by PRI AC7116 National Aerospace and Defense Contractors Accreditation Program Requirements for Nonconventional Machining AS7116/4 A CANCELLED Superseded by PRI AC7116/4 National Aerospace and Defense Contractors Accreditation Program Requirements for Laser Beam Machining (LMB) AS7766 2021-09 Terms Used in Aerospace Metals Specifications AS81914 A Tubing, Plastic, Flexible, Convoluted, Conduit, General Specification for AS81914/2 C Tubing, Plastic, extra Flexible, Convoluted Helical, Polyytetrafluoroethylene (PTFE) Close Convolutions AS81934/2 B (R) Bearing, Sleeve, Flanged, Self-Lubricating, - 65 degF to 325 degF AS81935/4 B Bearing, Plain, Rod End, Self-Aligning, Self-Lubricating, Narrow, Externally Threaded,-65 to +325 deg F AS83248/1 A O-Ring Molded from AMS7276 Material AS83461/1 C M83461 O-Ring Molded from AMS-P-83461 Rubebr AS83461/2 D Straight Thread Tube Fitting Boss O-Ring Molded from AMS- P-83461 Acrlonitrile Butadiene (NBR) Rubber AS85421 C Fitings, Tube, Fluid Systems, Separable, Beam Seal, 3000/4000 PSI, General Specification For AS8660 A CANCELLED Superseded by AMS8660 Silicone Compound NATO Code Number S-736 AS8879 D Reaffirmed 2024-04 Screw Threads - UNJ Profile. . . AS9100 D Model for Quality Assurance in Design, Development, Production, Installation and Servicing AS9101 G Requirements for Conducting Audits of Aviation, Space and Defense Quality Management Systems AS9102 C First Article Inspection Requirement AS9103 B Variation Management of Key Characteristics AS9110 C Quality Management Systems - Requirements for Aviation Maintenance Organizations AS9117 2016-03 Delegated Product Release Verification AS9131 D Quality Management Systems - Nonconformance Documentation AS9132 B Reaffirmed 2022-05 Data Matric Quality Requirements for Part Marking AS9138 2018-01 Quality Management Systems - Statistical Product Acceptance Requirements AS9145 2016-11 Requirements for Advanced Product Quality Planning and Production Part Approval Process AS9146 2022-09 Foreign Object Damage (FOD) Prevention Program - Requirements for Aviation, Space, and Defense Organizations AS930 F Fitting End, Straight Thread, Port Connection, Design Standard ALOFT AEROARCHITECTS PS-001 M Gas Tungsten Arc and Resistance Welding PS-002-1 G Marking and Labeling Instructions STC-PMA Parts AMERICAN GEN AIRCRAFT PROCESS SPECS (AGAPS) AGAPS1007 12 Material Callouts AGAPS1012 12 Installation, Countersinking, and Dimpling – Mechanical Fasteners AGAPS1013 7 Sheet Metal Fabrication AGAPS1081 2 Cadmium Plating AGAPS1201 6 Heat Treatment of Aluminum Alloys American Welding Society (AWS) AWS A2.4 2020 Ed 8 Standard Symbols for Welding, Brazing and Nondestructive Examination AWS A3.0M/A3.0 2025 Ed 14 Standard Welding Terms and Definitions AWS A5.01M/A5.01 2019 Ed 6 Procurement Guidelines for Consumables - Welding and Allied Processes - Flux and Gas Shielded Electrical Welding Processes AWS A5.02/A5.02M 2007 Ed 1 Filler Metal Standard Sizes, Packaging and Physical Attributes AWS A5.10/A5.10M 2023 Ed 13 Bare Aluminum & Aluminum Alloy Welding Electrodes and Rods AWS A5.12M/A5.12 2024 Ed 8 Tungsten & Tungsten-Alloy Electrodes for Arc Welding and Cutting AWS A5.14/A5.14M 2024 Ed 12 Nickel & Nickel-Alloy Bar Welding Rod AWS A5.16/A5.16M 2023 Ed 7 Titanium Welding Rods AWS A5.18/A5.18M 2023 Ed 9 Carbon Steel Electrodes & Rods AWS A5.28/A5.28M 2022 Ed 5 Low-Alloy Steel Electrodes and Rods for Gas Shielded Arc Welding AWS A5.31M/A5.31 2022 Ed 3 Fluxes for Brazing and Braze Welding AWS A5.32M/A5.32 2021 Ed 3 Welding Shelding Gases AWS A5.4/A5.4M 2012 Ed 11 Reaffirmed 2022 Stainless Steel Electrodes for Shielded Metal Arc Welding AWS A5.8M/A5.8 2019 Ed 11 Filler Metals for Brazing AWS A5.9/A5.9M 2022 Ed 10 Bare Stainless Steel Welding Rod AWS B2.1/B2.1M 2021 Ed 7 Welding Procedure & Performance Qualification AWS B2.2/B2.2M 2016 Ed 4 Brazing Procedure and Performance Qualification AWS B4.0 2016 Ed 8 AMD1 Standard Methods for Mechanical Testing of Welds AWS B5.2 2018 Ed 2 Qualification of Welding Inspector Specialists and Welding Inspector Assistants AWS C1.1M/C1.1 2019 Ed 6 AMD1 Recommended Practices for Resistance Welding AWS C3.4M/C3.4 2016 Ed 4 Torch Brazing AWS C3.6M/C3.6 2016 Ed 4 AMD2 Furnace Brazing AWS C7.3 2016 Ed 2 Electron Beam Welding AWS D17.1/D17.1M 2024 Fusion Welding for Aerospace AWS D17.2/D17.2M 2019 Ed 3 Resistance Welding AWS QC1 2016 Ed 6 AMD1 Standard for AWS Certification of Welding Inspectors AIRBUS AIMS0-1-04-003 ISS 3 Precipitation Hardened Stainless Steel (15-5PH) AIMS03-02-000 ISS 3 Aluminum & Aluminum Alloy Wrought Products - Plate AIPI09-01-014 ISS 3 Final Cleaning of Hydraulic Pipes AIRDROME AP2097 R Sleeve, Flareless Tube Fitting AIR TRACTOR PS132 D Tubing Fabrication, Beading and Flaring ALCOA FASTENING SYSTEMS CA35913 K1 Grommet Assembly, 130° Flush Head, .218 Nominal Diameter AN AN3,AN4,AN5,AN6,AN7,AN8,AN9, AN10,AN11,AN12,AN13,AN14,AN 15,AN16,AN17,AN18,AN19,AN20 CANCELLED 12 NOT 1 Replaced by NASM3 THRU NASM20 Bolt - Machine, Aircraft AN21,AN22,AN23,AN24,AN25,AN 26,AN27,AN28,AN29,AN30,AN31, AN32,AN33,AN34,AN35,AN36,AN 37 CANCELLED 11 NOT 1 Replaced by NASM21 THRU NASM37 Bolt - Clevis AN256 CANCELLED 5 NOT2 Boeing SL Supp 30M-AN256(NEW) Superseded by NASM256 Nut - Self Locking, Plate, Right Angle, 250 F AN310 CANCELLED 10 NOT 1,2 Superseded by NASM310 Nut, Plain, Castellated, Airframe AN316 CANCELLED 11 NOT 1 Boeing SL Supp 30M-AN316(NEW) Superseded by NASM316 Nut, Jam, Hexagon AN320 CANCELLED 14 NOT 1 Superseded by NASM320 Nut, Plain, Castellated, Shear AN426 CANCELLED 8 15-FEB-69 Use MS20426 Rivet - Solid, Countersunk 100° Precision Head, Aluminum Alloy AN490 CANCELLED 8 NOT 2 Superseded by AS49011 Rod End - Threaded, Aircraft AN743 CANCELLED 7 NOT 1 Boeing SL Supp 30M-AN743(A) Superseded by SAE-AS7431 Bracket, Support Clamp AN806 CANCELLED 7 NOT 1 Superseded by AS5168 Plug - Flared Tube AN814 CANCELLED 14 NOT 1 Boeing SL Supp 30M-814(A) Superseded by AS5169 Plug and Bleeder - Screw Thread AN815 10 w/AMD 1 Boeing Supp B Boeing SL Supp 30M- AN815(A) Union - Flared Tube AN818 20 w/AMD 4 NOT 4 Boeing Supp A Boeing S L Supp 30M-AN818(D) Nut, Tube, Coupling, Short AN819 14 CANCELLED Boeing Supp ORIG Superseded by MS20819 Sleeve, Coupling AN832 CANCELLED 8 NOT 1 Boeing SL Supp 30M-AN832(A) Use AS5406 per TABLE 1 Union - Flared Tube, 3/8 Bulkhead and Universal AN834 CANCELLED 9 NOT 2 Use AS1039 Tee, Bulkhead and Universal Flared Tube AN871 CANCELLED 9 NOT 1 Use AS5227 per TABLE 1 Flange - Straight AN894 CANCELLED 9 NOT 3 Use AS5173 Bushing, Screw Thread, Expander AN924 14 Boeing Supp B Nut, Tube, Bulkhead and Universal Fitting AN929 14 w/AMD 1 Cap Insert, Assembly, Pressure Seal, Flared Tube Fitting AN960 CANCELLED 21 NOT 2 Boeing Supp H Use NAS1149 Washer, Flat AN975 3 NOT 1,2 Washer - Taper Pin ANSI, ASME, ASTM ANSI/ASQ Z1.4 2003 (R2008) Reaffirmed 2013/2018 Sampling Procedures and Tables for Inspection by Attributes ANSI B46.1 SUPERSEDED Superseded by ASME B46.1 Surface Texture (Surface Roughness, Waviness and Lay) ANSI B89.6.2 SUPERSEDED 1973 (R2012) Superseded by ASME B89.6.2 Temperature and Humidity Environment for Dimensional Measurement ANSI H35.2 2024 Dimensional Tolerances for Aluminum Mill Products ANSI/MC96.1 SUPERSEDED 1982 Superseded by ISA MC96.1 Dimension Tolerances For Aluminum Mill ANSI/NCSL Z540.1 SUPERSEDED 1994 (R2002) Superseded by ANSI Z540.3 Calibration Laboratories and Measuring and Test Equipment General Requirements ANSI Z540.3 SUPERSEDED 2006 (R2013) Superseded by ISO/IEC17025 Requirements for the Calibration of Measuring and Test Equipment ANSI Y14.100M SUPERSEDED Superseded by ASME Y14.100 Engineering Drawing Practices ASME B1.1 2024 Unified Inch Screw Threads (UN, UNR & UNJ Thread Forms) ASME B1.3 2007 Reaffirmed 2017/2022 Screw Threads Gaging Systems for Acceptability: Inch and Metric Screw Threads (UN, UNR, UNJ, M, and MJ) ASME B46.1 2019 Surface Texture (Surface Roughness, Waviness and Lay) ASME Y14.1 2020 Decimal Inch Drawing Sheet Size and Format ASME Y14.100 2017 Engineering Drawing Practices ASME Y14.41 2019 Digital Product Definition Data Practices ASME Y14.47 2023 Engineering Product Definition and Related Documentation Practices ASME Y14.5 2018 Reaffirmed 2024 Dimensioning & Tolerancing ASME Y14.5.1 2019 Mathematical Definition of Dimensioning and Tolerancing Principles ASME Y14.5.1M SUPERSEDED 1994 (R2004) Replaced by ASME Y14.5.1 Mathematical Definition of Dimensioning and Tolerancing Principles ASTM-A1008/ A1008M 25 Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy With Improved Formability, Solution Hardened, and Bake Hardenable ASTM-A1016/A1016M 24a General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel and Stainless Steel Tubes ASTM-A213/A213M 25 Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater and Heat-Exchanger Tubes ASTM-A240/A240M 25a Chromium & Chromium-Nickel S.S. Plate, Sheet and Strip. . . ASTM-A269/A269M 25 Seamless and Welded Austenitic Stainless Steel Tubing for General Service ASTM-A313/A313M 18 Reaffirmed 2025 Stainless Steel Spring Wire ASTM-A380/A380M 25 Cleaning and Descaling Stainless Steel ASTM-A480/A480M 25b General Requirements for Flat-Rolled Stainless and Heat- Resisting Steel Plate, Sheet & Strip ASTM-A580/A580M 23 Stainless Steel Wire ASTM-A582/A582M 22 Free-Machining Stainless Steel Bars ASTM-A681 24 Tool Steels Alloy ASTM-A967/A967M 25 Chemical Passivation Treatments for Stainless Steel Parts ASTM-B209 14 SUPERSEDED Superseded by ASTM B209/B209M Aluminum and Aluminum Alloy Sheet and Plate ASTM-B209/B209M 21a Aluminum and Aluminum-Alloy Sheet and Plate ASTM-B210 12 SUPERSEDED Superseded by ASTM B210/B210M Aluminum & Aluminum Alloy Drawn Seamless Tube ASTM-B210/B210M 19a Aluminum and Aluminum-Alloy Drawn Seamless Tubes ASTM-B221 21 Aluminum and Aluminum Alloy Extruded Bars, Rods, Wire, Profiles and Tubes ASTM-B26/B26M 18 Aluminum-Alloy Sand Castings ASTM-B322 99 (R2020)E1 Cleaning Metals Prior to Electroplating ASTM-B338 17 Seamless and Welded Titanium and Titanium Alloy Tubes ASTM-B348 13 SUPERSEDED Superseded by ASTM B348/B348M Titanium and Titanium Alloy Bars and Billets ASTM-B348/B348M 21 Titanium and Titanium Alloy Bars and Billets ASTM-B545 22 Electrodeposited Coatings of Tin ASTM-B557 15 Reapproved 2023 Standard Test Methods of Tension Testing Wrought and Cast Aluminum and Magnesium Alloy Products ASTM-B594 19 Reaffirmed 2025 Standard Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products for Aerospace Applications ASTM-B600 22 Standard Guide For Descaling and Cleaning Titanium and Titanium Alloy Surfaces ASTM-B647 23 Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Webster Hardness Gage ASTM-B666/B666M 20 Identification Marking of Aluminum and Magnesium Products ASTM-B863 23 Titanium and Titanium Alloy Wire ASTM-B912 02 Reapproved 2018 Passivation of Stainless Steels Using Electropolishing ASTM-C665 24 Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing ASTM-D1002 10 Reapproved 2019 Standard Test Method for Apparent Shear Strength of Single- Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal) ASTM-D1056 20 Flexible Cellular Materials - Sponge or Expanded Rubber ASTM-D1193 24 Standard Specification for Reagent Water ASTM-D1876 08 (R2015) Reapproved 2023 Standard Test Method for Peel Resistance of Adhesives (T-Peel Test) ASTM-D2106 07 (R2012) Reapproved 2017/2022 Standard Test Methods for Determination of Amine Acid Acceptance (Alkalinity) of Halogenated Organic Solvents ASTM-D2240 15ε1 Reapproved 2021 Standard Test Method for Rubber Property - Durometer Hardness ASTM-D2471 99 CANCELLED NO SUPERSESSION Standard Test Method for Gel Time and Peak Exothermic Temperature of Reacting Thermosetting Resins ASTM-D2510 22 Standard Test Method for Adhesion of Solid Film Lubricants ASTM-D2942 02 (R2013) Reapproved 2018/2023 Standard Test Method for Total Acid Acceptance of Halogenated Organic Solvents (Nonreflux Methods) ASTM-D3359 23 Measuring Adhesion by Tape Test ASTM-D3951 18 Reapproved 2023 Standard Practice for Commercial Packaging ASTM-D4066 13 Reapproved 2019 Standard Classification System for Nylon Injection and Extrusion Materials (PA) ASTM-D4080 15 Reapproved 2020/Reaffirmed 2025 Standard Specification for Trichloroethylene, Technical and Vapor-Degreasing Grade ASTM-D445 24 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids ASTM-D512 23 Standard Test Methods for Chloride Ion In Water ASTM-D5363 16 Reapproved 2024 Standard Specification for Anaerobic Single- Component Adhesives ASTM-D6193 16 Reapproved 2020 Standard Practice for Stiches and Seams ASTM-D6576 20 Standard Specification for Flexible Cellular Rubber Chemically Blown ASTM-D6779 23 Standard Classification System For and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) 1 ASTM-D695 23 Standard Test Method for Compressive Properties of Rigid Plastics ASTM-D770 11 Reapproved 2019 Standard Specification for Isopropyl Alcohol ASTM-D903 98 (R2010) Reapproved 2017/2025 Standard Test for Peel or Stripping Strength of Adhesive Bonds ASTM-E1004 23 Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method ASTM-E110 14 Reapproved 2023 Standard Test Methods for Indentation Hardness of Metallic Materials by Portable Hardness Testers ASTM-E140 12b Reapproved 2019 Standard Hardness Conversion Tables ASTM-E1417/E1417M 21 Liquid Penetrant Examination ASTM-E1444/E1444M 25 Magnetic Particle Examination ASTM-E1447 22 Standard Test Method for Determination of Hydrogen in Titanium and Titanium Alloys by Inert Gas Fusion Thermal Conductivity/Infrared Detection Method ASTM-E1742/E1742M 23 Radiographic Examination ASTM-E18 25 Standard Test Methods for Rockwell Hardness & Rockwell Superficial Hardness of Metallic Mats. ASTM-E29 22 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications ASTM-E215 22 Standard Practice for Standardizing Equipment for Electromagnetic Testing of Seamless Aluminum-Alloy Tube ASTM-E220 25 Standard Test Method For Calibration Of Thermocouples ASTM-E230/E230M 23a Temperature-Electromotive Force (EMF) Tables for Standardized Thermocouples ASTM-E2016 22 Standard Specification for Industrial Woven Wire Cloth ASTM-E2375 22 Ultrasonic Testing ASTM-E3 11 Reapproved 2017/2025 Standard Guide For Preparation Of Metallographic ASTM-E399 24 Standard Test Method of Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials ASTM-E3022 25 Standard Practice for Measurement of Emission Characteristics and Requirements for LED UV-A Lamps Used in Fluorescent Penetrant and Magnetic Particle Testing ASTM-E8/E8M 25 Standard Test Methods for Tension Testing ASTM-F2111 22 Standard Practice for Measuring Intergranular Attack or End Grain Pitting on Metals Caused by Aircraft Chemical Processes ASTM-F22 21 Standard Test Method for Hydrophobic Surface Films by the Water-Break Test ASTM-MNL12 1993 Ed4 Manual on the Use of Thermocouples in Temperature Measurement APPLIED MATERIALS 0250-00098 8 Packaging Specifications 0250-01019 3 Cosmetic Inspection Standards & Specifications 0250-01033 11 Engineering Reqmts for Supplier Part Identification 0250-27105 17 Minimum Product EHS Requirements 0250-36352 12 Critical Part COC and Product Quality Report Requirements 0250-70351 7 Requirements for Component Cleaning ARCONIC EN1182ND AD Eddie-Bolt 2 Nut, Shear, Lightweight ARROWHEAD PRODUCTS APPS-10-M-100 H Heat Treatment of Corrosion and Heat Resistant Alloys APPS-10-M-200 NC Heat Treat of Corrosion and Heat Resistant Alloys (Boeing Commercial Airplane Company Programs) APPS-3-M-100 F Cleaning and Passivating of Corrosion and Heat Resistant Alloys and Nickel-Base Alloys MPS/MPQ-105-450 B Cleaning and Packaging of Booster Propellant Feed Assemblies (In-Procedures) ULA Atlas V and Vulcan Lines and Joints PCN V130 NC Manufacturing Vacuum Heat Treat Instruction QCI-08-024 L Identification ATK Tactical Systems P-10001 K Identification and Marking BAE SYSTEMS BAE-JSF-QMS-886-04-PC 5 Design Visual Examination Procedure for JSF B&E PS1801 B Standard Pipe Beads BEECHCRAFT 03-01-016 C Part Number and Lot Identification 78-37 OBSOLETE Replaced by QAI 03-01-016 (5-24-2004) 102501 4 End - Solder Type Connection, Tubing 102728 H End - Beaded Tubing 110220 E Bead - Standard 111703 5 Method-100 degree Screw Countersink 112135 6 Fitting - Flared Tube, Brass 115074 D Tubing end - Small Beaded 118636 40 PSD 1,2,3 Adhesive Systems Metal Bonding 130077 12 Insert, Screw Thread, High Strength 130078 4 Method-Screw Thread Insert Installation 131999 ORIG Boss - 7/16-20 Internal Thread 132105 2 Joint Classification - Brazing 132396 G Fastener Codes 308426 13 Method – Riveting of 100 Degrees Countersunk Head BS1000 1 Substitution, Preferred Item and Source of Supply Database BS20014 A Hydraulic System / Component Cleanliness BS201 40 PSD 1(2) Adhesives, Cements, Sealers BS20615 4 PSD 2(7),3(3) Fabrication of Glass Fabric Base Laminates BS21896 19-Jun-70 Pressure Test & Leak Detection Procedure BS22020 4 Finish Spec. for Beech Model 101 Airplane BS22455 29 Finishing Procedure for Models using Urethane Finishes BS235505 1 Tube Flaring BS23673 G Finish Specification BS23731 8 CANCELLED Superseded by TM2284 Secondary Materials For Metal Bonding And Composite Bonding BS23865 7 PSD 3 (rev 6) Corrosion Inhibiting Adhesive Primer BS23933 6 PSD 1 rev 2 Qualification of Welders and Welding Operators BS23967 4 Installation of Nutplates, Studs… BS24058 ORIG PSD 1 Fabrication of Titanium Parts BS24580 ORIG Parts List (PL) Interpretation Specification BS24746 15 Index of Specifications, Standards, And Other Publications Applicable to the King Air Model C90A, C90GT BS24749 13 Index of Specifications, Standards and Other Publications Applicable to the Super King Air Models B200, B200C, B200T, etc. BS24757 6 Finish Codes for Corrosion Protection…. BS249 B EO C87381 Stress Relief of Steel Parts After Welding…. BS24942 16 PSD 1 (rev 7) Raw Material Substitution Specification BS25032 4 OBSOLETE Superseded by TM3403 Corrosion Resistant Fuel Cell Epoxy Primer BS25065 13 Finish Specification For Model 390 BS25112 5 Integral Fuel Tank Sealing Specification BS25116 15 Fracture Critical and Durability Critical Parts Control Requirements BS25249 5 Fluid System Tubing Fab & Insp BS25264 4 Design and Installation of Hydraulic Tubing, Assemblies, and Tube Fittings BS25272 ORIG EO G92598 Fusion Welding of Titanium and Titanium Alloys BS25314 21 Finish Specification For Model 4000 BS253303 3 CANCELLED See BS25691 BS25339 3 CANCELLED Superseded by BS311327 & P1103 Hot Bending or Forming of Alum. Alloys BS25526 ORIG Stress Relief & Embrittlement Relief … BS25554 2 Polishing Metal Surfaces BS25649 1 Non-Destructive Inspection Processes Substitution Specification BS25670 2 Tubing Acceptance BS25691 23 Control Of Product Mfg…. (PORTIONS PERTAINING TO MACHINING PRACTICES HAVE BEEN REPLACED BY TEXTRON SPEC TP1202) BS25707 23 Fluorescent Penetrant & Magnetic Particle Inspection Part Exemption List BS2591 D EO B83001, B86860, B87960, B88060, C22692A, D45390, D45416, D55662 Standard Engineering Drawing Callouts For General Materials, Practices, And Processes BS2647 L PSD 8,9,10 Adhesive Bonding - Metal to Metal and Sandwich BS305511 3 Approved Raw Material Substitution by Part Number BS311327 3 Forming of Aluminum Alloys BS361 12 Standard Finish Specification BS383 29 Identification Markings, Materials, Equip & Req BS385372 1 Grain Direction Identification BS392875 1 Reprocessing Specification For HBS Parts BS424 4 Commercial Aircraft Spot welding of Aluminum & Magnesium Alloys BS510 5 Design of Welded Joints in Aluminum Alloy BS511 9 Design of Welded Joints in Steels and Corrosion and Heat Resisting Alloys SAS02-004 3 General - Grain Direction SAS03-002 A Standard Allowance Spec for Sheet Metal - Flange Width SAS03-003 5 Standard Allowance Specification for Sheet Metal - Edge Conditions SAS03-008 3 Sheet Metal - Surface Imperfections SAS03-009 5 Sheet Metal - External Surface Imperfection Limitations and Repair Procedures SAS06-001 ORIG Holes - Machined Hole Tolerances SAS07-002 ORIG Forming - Metal Thickness Variation SAS07-003 ORIG Thinning of Formed Thermoplastic SAS09-002 A Dimensional Tolerances – Contours of Formed Parts SAS09-006 ORIG Dimensional Tolerances – Free State Variation of Machined Parts SAS10-004 3 Machining - Corner Radii SAS10-005 ORIG Machining - Surface Roughness & Machined Finishes SRP001 9 Application of Surface Smoothness Material Beta Technologies BTPS 00-001 C Identification of Parts BTPS 01-001 B Solvent Cleaning BTPS 11-001 B Conventional Machining of Metals BTPS 11-002 B Forming of Metals BTPS 22-003 A Installation of Self-Clinching Nuts BTPS 33-001 A Installation of Externally Swaged Fittings BTPS 55-002 B Fluorescent Penetrant Inspection BTRS 010 F Finish Codes BTRS 300 D Special Processes List BTRS 400 A Controlled Materials List BTRS 510 A Interpretation of Digital Product Definition PL-0008 A Supplier Packaging and Labeling Requirements CARLETON LIFE SUPPORT SYSTEMS PD1635250 R Materials List PD1635306 D Qualification and Certification of Nondestructive Testing Personnel PUB23854 A Specification Index for Materials, Processes and Finishes SP1638392 A 2024-T3 AL Sheet and -T351 Plate SP1638394 A 6061-O AL Sheet and Plate SP1638396 A 6061-T6 AL Sheet and -T651 Plate SP1638424 A Conversion Coating of Aluminum SP1638435 A Primer and Painting SP1638442 A High Solids Epoxy Primer SP1638444 NC Waterborne Epoxy Primer SP1638510 A 6061-T4, -T4510 and -T4511 Extrusion ST1637803 AE Manufacturing Quality, Standard for CHERRY AEROSPACE 2L426Y-E C Lockbolt Pin, Pull Type Alum Alloy 1.0 Pintail 100° Flush Tension Head CR7771S AL Titanium Blind Bolt Protruding Head, Titanium Stem CLICK BOND CB2000 1 Stud, Medium Base, Adhesive Bonded CB3503 5 Nutplate, No Lug, High Reuse CB3511 1 Nutplate, One Lug, High Reuse CB9566 4 Nutplate, Miniature, Floating COBHAM PD434008 H Polyurethane Application Procedure on Nameplates and Labels PUB24230 NC Cancelled and Superseded Specification List SP1638399 A 6061-T6, -T6510 and -T6511 Extrusion SP1638418 B Heat Treatment of Aluminum, Specification for SP1638505 A 6061 Al Bar, Rod, Wire, Special Shapes; Rolled, Drawn or Cold Finished SP1638562 NC 2024 Aluminum Sheet and Plate COLUMBIA HELICOPTERS 04-RDE-0110 G Process Specification: Methods of Identification Marking 06-RDE-0311 H Supersession Document - Materials, Processes, and Standards Supersession Document (Boeing to Columbia Helicopters Inc) 06-RDE-0621 C Process Specification: Fastener Installation Procedures 06-RDE-1111 U Process Specification: Finish and Process Codes 12-RDE-0204 B Computer - Generated Model Data Management COMPRESSED GAS ASSOCIATION (CGA) CGA G-10.1 2023 Ed 9 Commodity Specification For Nitrogen CGA G-11.1 2023 Ed 8 Commodity Specification For Argon CGA G-4.3 2018 Ed 8 Commodity Specification For Oxygen CGA G-9.1 2018 Ed 9 Commodity Specification For Helium DASSAULT-FALCON JET FES103 K Heat Treatment of Aluminum Alloys FES104 M Heat Treatment of Steels FES107 P Fusion Welding of Aluminum Alloys FES108 AH Finish specification FES109 P Application of Corrosion Preventive Compound FES110 J Welding Symbols FES111 H Fusion Welding of Steel FES112 AA Parts Identification FES115 G Abrasive Cleaning of Metals FES116 R Chemical Cleaning of Metals FES118 H Natural Satin Finish For Metallic Materials FES119 N Metal Fabrication Practices FES120 K INACTIVE Replaced by FPS-MFG-00023 Welding Operators Test FES121 G Plastic Mat: Low Press. Laminated Glass Fiber FES132 CK Material and Parts Substitution FES149 F Hole Tolerances FES159 E Hardness and Conductivity Testing, Procedures and Standard Values For FES179 Y Plating Procedures for Cosmetic Parts FES193 T 3D Model Dimensional Tolerances FES196 B CANCELLED Standard Practice Specification Applications FES199 B Acceptable Deviations Between 3D Engineering Definition and Resulting Machined Parts Report 40010 F Standard Practice FES WI-00497 E Cosmetic Plated Parts (Acceptance Criteria for) DAVIS ENGINEERING DE-002 5 Davis Part Marking Procedure Marine And Commercial Product DE-144 5 Part Marking Procedure for General Aerospace Product DE-157 7 Acceptance Limits and Repair Instructions for Defects in Sheetmetal/Tubing Components DE-176 2 Cosmetic Inspection Standard DUNCAN AVIATION GDMR101 11/2/01 General Design Mfg. Reqs. PQ3429CE 19 Part Manufacturer Approval WQR-100 E Welder Qualification Requirements EATON 24538 BF Flange - 20⁰, Coded 35235 U Sleeve, Flareless Swaged Tube 35381 G Sleeve, Flareless Shallow Groove ACES1170 K Materials For Machined Parts ACES13 CB APP A7(A),A8(D),A9(B), A10(A),A13(A), A14(A),A15(A), A16(NC) Welding of Parts, Fittings, Tubing and Assemblies for Aircraft and Missile Service ACES1555 Y Commercially Pure Titanium Sheet Metal Flanges, Fabrication of ACES157 H Heat Treatment and Related Processes for 300 Series Corrosion Resistant Steels ACES16 CV Surface Treatment of Metals for Corrosion Resistance. ACES16P14 CA Mechanical Cleaning / Mechanical Passivation ACES1705 E Industrial Products Workmanship and Appearance Levels ACES20 BR Marking Parts, Processes for ACES2192 T Welding, Resistance, Spot Implementation of AMS-W-6858 ACES2249 G Rivets, Solid and Semitubular, Installation of ACES2600 BY Inspection, Fluorescent Penetrant ACES2687 AD Fusion Weldments, Inspection Processes and Acceptance Standards for ACES284 J Superseded by ACES2934 ACES2898 BH Product ID, Aeroquip Fluid Conveyance ACES2934 P Key Characteristics, Identification and Implementation of ACES35 AB APP1 rev A APP2 rev D, APP4 rev A APP5 rev A Forming Metal Tubing, Process & Qual. Reqs. ACES70 AA Trademarks, Aeroquip ACES7085 D Water Break Test, Procedure for ACES7851 L CANCELLED Superseded by ACES2600/ACES2602 Inspection, Fluorescent and Radiography ACES7874 Y APP 1 rev W APP 2 rev AC APP 3 rev C Acceptance Test of 787 Aircraft NGS and Cactus Ducts ACES7877 B Chemical Conversion Coating….. ACES7904 A ADD1 Coating, Epoxy-Polyamide, Chromate Free, Corrosion Protective, Process Specification For AE62905 A Sleeve, Fire Resistant ES-1 T Interpretation of Drawings for Irvine and Euclid Product Lines MCS86845 C Material Control Specification - Titanium Tube, Seamless and Welded MCS86847 D Welded Inconel 718 Tube Made From AMS5596 PD434006 T Fusion Welding (Click on attachments tab of the PDF to view forms referenced in spec.) PS85613 AG Welding Process Specification PS85613 Sect VI AD Resistance Welding PS86746 A Tape, Tube Identification, Application of PS86747 D Insulation Systems on Ducts and Tubes, Fabrication and Assembly of PS86766 D Primer and Paint, Preparation and Application of PSI-ISO-06 P Purchasing QCS06658 AJ Penetrant Inspection QCS3129 AW Quality Manual (Eaton Conveyance Systems) QCS85028 BE Calibration Procedure QCS85064 L Identification Marking Methods QCS85604 NC Identification Marking Methods QCS85655 G Ducting Acceptability Limits For Tube Bending, Forming & Straightening EMBRAER MEP02-015 K Aluminum Alloy Alclad 2024, Fine Grained - Sheet MEP08-029 F Lubricant Oil for Tube Bending MEP10-033 L Ink for Metallic Parts Identification MEP21-023 NC Alkaline Degreasing for Ultrasonic Cleaning NE01-040 U Inks for Marking of Parts NE01-103 AM Parts - Marking Methods NE03-002 G Steel Sheet Parts - Minimum Cold Bend Radii NE03-003 L Aluminum Alloy Sheet - Minimum Cold Bend Radii NE03-006 BD Riveting - Drilling, Countersinking and Dimpling NE03-009 T Tube Bending - Requirements NE03-051 R Metallic Parts - Cutting, Chamfering and Deburring NE03-068 O Bolts and Screws - Drilling, Countersinking and Dimpling for Installation NE03-071 L Machined Metallic Details - General Tolerances NE03-073 E Dimensioning and Tolerancing NE03-076 M Aluminum Parts - Forming and Straightening NE03-077 E Drainage - General Requirements NE03-080 N Metal Sheet or Extruded Parts General Tolerances NE04-003 G Tube - Standard Bead End NE05-007 NC Welding and Brazing Symbols NE06-005 N Solid Rivets - Installation NE06-013 S Rivet, Solid, 120° Flush Interference Head - Requirements for Grip Selection and Installation NE06-025 W Blind Fasteners - Installation NE06-034 AD Nut Plate - Installation NE07-001 Y RFA TA44-4-29-15 Liquid Penetrant Inspection NE07-012 AF Aluminum Alloys Hardness and Conductivity Values NE07-051 E Embraer Production Part Approval Process (EPPAP) NE15-309 K Joggles In Extruded and Performed Sheet Sections NE40-002 AA Aluminum and Its Alloys - Solution Heat Treat NE40-006 AC Aluminum and Its Alloys - Chemical Conversion Coating NE40-012 CQ Metallic Parts - Cleaning NE40-026 L Protection of Metallic Surfaces With Anticorrosive Oil. NE40-047 F Austenitic Stainless Steel 300 Series - Heat Treatment NE40-051 AA Precipitation Hardening Corrosion Resistant Steel - Heat Treatment NE40-053 E Titanium and Its Alloys - Fusion Welding (TIG) NE40-056 L GTAW Fusion Welding Process For Carbon Steel, Low Alloy Steel, Corrosion Resistant Steel and Nickel Alloys NE40-072 AB Shot Peening NE40-073 F Resistance Welding - Spot and Seam NE40-077 S Equipment for Thermal Processing - Temperature Control and Classification NE40-081 Y Stainless Steels - Passivation NE40-118 N Fluid Line Components - Cleaning and Decontamination NE40-143 AY Fluid Resistant Epoxy Primer (MEP 10-059 Types I and II) for Internal Metallic and Composite Parts - Application Requirements NE40-175 E Titanium Parts - Forming and Straightening NE40-213 C Steel Parts - Forming and Straightening NE40-215 K Titanium and Its Alloys - Cleaning NE40-235 I Finishing of Polished and to be Polished On Bare Aluminum External Parts NE42-027 Y Parts - Temporary Protection NE44-001 D Glass Bead Peening NE44-006 F Barrel Finishing NE90-195 ORIG Laser Cutting Of Metals PF05-019 J Superseded by NE40-215 PF80-241 Q RFA TA54-6-16-15 Surfaces for Electrical Bonding - Preparation and Protection ERICKSON AIR- CRAIN ES2000 AN Material and Process Specifications Index FLAME CONTROL COATINGS 900-SA Series 01/10 Low Temperature Curing High Performance Industrial Heat Resistant Coating FORD AEROSPACE AFS260382 ORIG Glass Bead Peening GAMAH F1009 N Flange F1041 S Flange, Aluminum, Heavy Duty Coupling F20000 F F20000 Flange Series 20 F20000/F21000 F BACF22W Flange F21000 F F21000 Flange Series 21 F31300 G F31300 Flange Butt Welded Series 34 GW30300 A Flange - Butt Welded Series 30 G2J-01 JULY 1992 Swaging of Gamah Coupling Flanges N20000 G Nut - Series 20 T2268 E Coupling Half - Series 20 GKN AEROSPACE DS100 ISS 5 Protective Finishes DS104 ISS 5 Marking of Parts HARTZELL H-S-13 AJ Parts Identification and Marking HONDA AIRCRAFT COMPANY, INC. HACI G 5-2-1 B (FINAL) CANCELLED without replacement Tooling General Requirements Manual HACI G 5-2-3 A (FINAL) Superseded by HACI G 5-4-50 Tooling, Tool Fabrication Manual HACI G 5-2-24 D External Tooling Supplier Requirements HACI G 5-4-50 B Tooling Fabrication Guideline HACI P 5-2 A (FINAL) Superseded by HACI M 5-2 Tooling Control HJDS-AR100 ORIG Aerodynamic Requirements Specification Collector HJDS-CP001 C EO C1,C2,C3 Code - Process and Finish HJDS-PD001 B Dimensioning & Tolerancing and Product Definition Practices HJDS-SL002 A EO A1 Metallic Material Thickness Substitution List HJDS-SL004 B Metallic Material Substitution List HJMS-5004 D Preimpregnated E-Glass Fabric. . . HJMS-5010 C Preimpregnated Carbon Fiber Fabric. . . HJMS-5012 C Preimpregnated Fiberglass. . . HJPS-0006 P Aerodynamic Smoothness & Tolerances for Manufacturing HJPS-1006 A EO A1,A2,A3, A4, A5 Sheet Metal Practices HJPS-1007 NC EO NC1 Forming and Fabrication of Aluminum Alloys HJPS-1008 A EO A1,A2 Carbon, Alloy, Corrosion and Heat Resisting Steels and Nickel Based Alloys, Forming, Fabrication and Straightening of HJPS-2003 D General Machining Processes HJPS-2008 C EO C1 Shimming Practices HJPS-3102 J Fabrication and Acceptance of Autoclave Cured Composite Parts HJPS-3106 A EO A1,A2 Machining of Composite Parts HJPS-4001 A EO A1 Fusion Welding - Aluminum and Aluminum Alloys HJPS-4004 ORIG EO -1 Welding of Steels HJPS-5001 A Heat Treating Aluminum Alloys HJPS-6001 H EO H1,H2,H3,H4,H5 Identification Marking of Parts and Assemblies HJPS-6002 M EO M1,M2,M3,M4,M5 Sealing Methods and Materials HJPS-6004 B CANCELLED Superseded by HJPS-T006 HJPS-6005 C Passivating Corrosion-Resistant (Stainless) Steel HJPS-6006 B EO B1,B2 Integral Fuel Tank Coating Application HJPS-6007 G EO G1,G2,G3 Epoxy Primer Application HJPS-6008 B EO B1,B2 Cadmium Finishes HJPS-6011 H EO H1,H2 Chemical Conversion Coating of Aluminum Alloys HJPS-6012 G Chromic Acid Anodizing of Aluminum and Aluminum Alloys HJPS-6016 B Stripping of Organic Coatings HJPS-6019 J EO J1,J2 Cleaning of Aluminum and Aluminum Alloys HJPS-6020 D EO D1 Solvent Wipe Cleaning HJPS-6025 C EO C1,C2 Application of Polyurethane Topcoats HJPS-6027 A EO A1,A2,A3,A4 Brush Plating HJPS-6031 F EO F1,F2 Application of Exterior Urethane Coatings HJPS-6033 ORIG EO -1,-2 Alkaline Cleaning of Exterior Surfaces for Paint HJPS-6034 B EO B1,B2 Testing, Equipment and Terminology for Paint HJPS-6035 B EO B1 Boric Sulfuric Acid Anodizing of Aluminum Alloys HJPS-7008 ORIG EO ORG,-1,-2,-3 Chemical Milling of Metals HJPS-7009 A Application of Maskants HJPS-8001 A EO A1,A2,A3, A4, A5 Shot Peening of Metal Parts HJPS-8002 ORIG EO -1 Grinding of Steel parts HJPS-8005 ORIG Laser Profiling HJPS-8006 ORIG Water Jet Profiling HJPS-9001 F EO F1, F2 Installation and Inspection of Solid Rivets HJPS-9002 F EO F1, F2, F3 Installation and Inspection of Blind Rivets HJPS-9005 D EO D1 Installation of Threaded Fasteners HJPS-9013 B EO B1 Installation of Shrink Fit Bushings HJPS-9016 D EO D1 Aircraft Electrical Bonding and Grounding HJPS-9019 G EO G1,G2,G3,G4,G5 Tightening of Threaded Fasteners and Connectors HJPS-9020 ORIG EO -1 Fabrication of Tubing Systems HJPS-9022 B EO B1,B2 Cleaning and Pressure Testing of Tubing and Hoses HJPS-9025 C Precision Cleaning of Oxygen Tubes and Components HJPS-9030 ORIG Installation and Inspection of Permalite Tube Fittings HJPS-T002 ORIG EO -1 Hardness and Conductivity Testing of Metals HJPS-T006 B Fluorescent Penetrant Inspection HJPS-T012 ORIG Radiographic Inspection of Metallic Materials, Parts, and Joints HOWMET AEROSPACE ELS420 P Pin, Eddie Bolt 2, Protruding Tension Head, Hex or Spine-Lok Socket Recess, 95 KSI Min Shear, 6AL-4V Titanium MF6000 ORIG Nut-Anchor, Miniature, Right Angle, Floating MF6001 C Nut-Anchor, Right Angle, Miniature, Floating, Self-Locking HYDRAFLOW 12F63 AA Flange - 12J63 Series Flexible Coupling 12F70 V Flange - 12J70 Series Flexible Coupling 14F02 AM Flange 14F03 AC Flange 14F05 T Flange - Welded Type, 14J02 Series Flexible Coupling 14F13 F Flange 14K03 N Body - Single Flange Welded, 14J02 Series Flexible Coupling per AS4736 21F02 AB Flange - Low Profile AD095 NC Adapter LC008 L Flange, Adapter LC009 L Flange, Adapter LC011 E Flange LC012 M Flange LC021 W Flange LC138 G Flange LC352 G Flange LC1063 A Tee Fitting LC1064 A Cross Fitting LC1070 B Tee Fitting LC1072 NC Reducer LC1074 A Tee Fitting LC1075 A Tee Fitting LC1076 B Body LC1078 C Boss Fitting LC1084 A Tee Fitting LC1085 B Body LC1121 NC Cross Body LC1122 NC Tee Body LC1142 NC Sleeve LC1478 NC Adapter LC1479 NC Flange LC1619 NC Flange, Reducer PS006 R Installation Instruction For Mechanical Attachment of Hydraflow Swage Type Fittings To Tubing PS006-1 A Installation Instructions for Mechanical Attachment of Hydraflow Swage Type Fittings to Tubing Using a Electric Torque Motor, Addendum to PS006 TC001 Y Washer TC036 J Body TC037 M Nut, Type I TC038 N Ferrule TC040 G Body, Type II TC042 L Nut Assembly TC046 L Flange TC047 H Threaded Flange TC058 F Threaded Flange VC025 D Flange, Jump Size ISO STANDARDS ISO/IEC16022 ED 3 2024-05 Information Technology - Automatic Identification and Data Capture Techniques - Data Matrix Bar Code Symbology Specification ISO/IEC17025 ED 3 2017-11 General Requirements for the Competence of Testing and Calibration Laboratories ISO/IEC TR29158 SUPERSEDED ED 1 2011-10-15 Superseded by ISO/IEC29158 Information Technology - Automatic Identification And Data Capture Techniques - Direct Part Mark (DPM) Quality Guideline ISO/TS9002 ED 1 2016-11-01 Quality Management Systems-Guidelines for the Application of ISO 9001 ISO12 ED 2 Aerospace - Pipelines - Identification ISO228-1 ED 4 2000-09-01 Pipe Threads ISO10012 ED 1 2003-4-15 Quality Assurance Requirements For Measuring Equipment ISO10579 ED 2 2010-03-01 Technical Drawings - Dimensioning and Tolerancing - Non- rigid parts ISO18490 ED 1 2015-06-01 Non-Destructive Testing - Evaluation of Vision Acuity of NDT Personnel ISO19011 ED 3 Guidelines for Auditing Management Systems KOREA AEROSPACE IND. (KAI) A84MP0001 ORIG Finish Requirements A84MP0306 ORIG Application of Solid Film Lubricants A84MP0308 ORIG Marking of Aircraft and Aerospace Ground Equipment Parts A84MP0317 ORIG Machining and Surface Integrity of Metallic Materials A84MP0411 ORIG Fluorescent Penetrant Inspection A84MP0415 ORIG Hardness and Conductivity Test for Verifying Heat Treatment Condition A84MP0417 ORIG Conductivity Test A84MP1003 ORIG Forming of Ferrous Alloy A84MP3235 ORIG Tolerances for Formed Metal Parts A84MP3511 ORIG Finish Application and Codes A84MP3513 ORIG Requirements of Marking of Aircraft and Aerospace Ground Equipment parts 85MP0001 A Finish Requirements 85MP0306 ORIG Application of Solid Film Lubricants 85MP0308 ORIG Marking of Aircraft and Aerospace Ground Equipment Parts 85MP0314 ORIG Heat Treatment of Steels 85MP0317 ORIG Metal Removal Procedures and Limitations 85MP0411 ORIG Penetrant Inspection 85MP0415 ORIG Hardness and Conductivity Test (Nondestructive Methods for Verifying Heat Treat Condition) MARSHALL DEF STAN 03-2 6 Superseded by AMS03-2 Cleaning and Preparation of Metal Surfaces DEF STAN 03-32 Part 2 5 Pre-Treatment and Painting of Vehicles, Engineer Equipment and Components Part 2: Systems for Ferrous Armour DS 04-01-033 2 CANCELLED No supersession Pipe Beading - 'Flexible Connections DS 04-01-040 2 Geometry For The A.G. Belling of Tube DS 04-01-089 2 Surface Finish DS 04-01-101 10 General Manufacturing Tolerances and Allowables DS 05-01-001 61 OBSOLETE When invoked use MMP 05-01-001 Protective Treatment DS 06-01-001 23 OBSOLETE When invoked use MMP 06-01-001 Identification Marking MMP 05-01-001 10 Protective Treatment MMP 06-01-001 5 Identification Marking MMP0000 17 General Manufacturing and Design Requirements MMP0004 17 Non-Destructive Testing Fluorescent Penetrant Inspection MMP0008 3.01 Non-Destructive Testing Radiographic Inspection MMP0009 6 Electrical Conductivity Testing - Aluminum Alloys MMP0010 4.03 Electrical Conductivity Testing - Aluminum Alloys MMP0011 2.01 Pressure Testing of Dry System Pipes MMP0015 9 Heat Treatment Aluminum and Aluminum Alloys MMP0024 4.01 Testing Requirements For Conformation of Satisfactory Heat Treatment Process - Metals MMP0054 7 Application of Corrosion Inhibiting Compounds MMP0063 5 OBSOLETE When invoked use MMP320 Manual Argon Arc Welding of Aluminum & Aluminum Alloys MMP0071 7 Final Cleaning of Oxygen, Nitrogen & Water System Pipes and Associated End Fittings MMP0072 2 OBSOLETE Superseded by MMP140 Removal of Surface Finish MMP0075 6 Non-Structural Pipe Forming MMP0140 7 Removal of Surface Coatings MMP0142 17 Application of Chromate conversion Coating By Brush or Swab MMP0181 17 Application of Chromate Conversion Coatings to Aluminum and Aluminum Alloys By Immersion MMP0210 13 Application of Integral Fuel Tank Coating MMP0308 2.01 Installation of Wiggins and Hydraflow Swaged Couplings MMP0314 2.01 CANCELLED CANCELLED without replacement Application of Fluid Resistant Epoxy Primer MMP0320 9 Fusion Welding of Metals GTAW/MAA MIDDLE RIVER AIRCRAFT SYSTEMS (MRAS) 608C5510 B Sheet Metal Parts - Shop Run Tolerances 608C5511 ORIG Aerodynamic Cleanliness Acceptability Limits 747-8 STM INDEX 85 Material Specification Index for Boeing 747-8 747-8 STP INDEX 32 Engineering Process Index for Boeing 747-8 A320-C919-PP20 STP INDEX 50 Engineering Process Index for A320, C919 and PP20 GE-CF34 STM INDEX 34 Material Specification Index for CF34-10 GE-CF34 STP INDEX 17 Engineering Process Index for CF34-10 GE-80C STM INDEX 7/2/2025 Material Specification Index for CF6-80 Fan Reverser GE-80C STP INDEX 96 Engineering Process Index for CF6-80C2 Fan Reverser STPB-73030 G Fastener Installation and Acceptability Limits STPG-55014 A Welding, Fusion, Steel, Corrosion and Heat Resistant Alloys - Critical Applications STPG-73046 D Identification Markings STPM-50074 C Process Specification for Surface Cleaning & Preparation Prior to Bonding & Priming STPM-73025 D Process Specification for Sheet Metal Parts Fabrication STPM-73030 G Fastener Installation and Acceptability Limits STPM-73051 A Process Specification for Bonding of Metallic Components With High Temperature Modified Epoxy Adhesive Film STPM-73058 F Painting Composite and Metal Parts and Assemblies STPM-75200 H Process Specification for Controlled Expendable Materials STP-MR20002 ORIG Installation of Solid Fasteners for High Temp Applications STP-MR72305 A Fabrication of Heat Resistant Alloy Sheet Metal Parts MITSUBISHI HEAVY INDUSTRIES 580AS ORIG Reinforcing Ring - Bead, Welding Duct 996AS A Attachment Reinforcement Rings P1501 H Welding - Spot, Seam - General National Aerospace Standard (NAS) NAS0331 2 Bearing Installation and Retention by Swaging or Staking NAS1031 7 Nut, Self-Locking, Plate, Two Lug, Regular Height, Floating NAS1057 10 11-21-2014 Spacer, Sleeve, Screw and Bolt, High Temperature, Non Magnetic NAS1068 13 Boeing Supp D INACTIVE - Use MS21075 NAS1080 14 Collar, Swage Locking For Pull-Type and Stump-Type Lockbolts NAS1095 2 Stabilized 2022 Flareless Fitting Connections Fabrication And Assembly NAS1097 11 Boeing Supp B Rivet, Solid, 100 Deg NAS1102 11 Screw, Machine, Flat 100° Head, Full Thread, Offset Cruciform NAS1130 5 Insert, Screw Thread, Helical Coil, Free Running and Self- Locking, Tangless NAS1149 8 Boeing Supp N Washer, Flat NAS1198 7 Rivet - Solid Universal NAS1199 7 Rivet - Solid - 100° Flush Head A286 Corrosion Resistant Steel NAS1200 12 Boeing Supp B Rivet, Solid, 100 Deg NAS1201 8 Chain, Bead Components and Assembly NAS1222 2 INACTIVE Use MS21209 NAS1291 16 Nut, Self-Locking Hexagon-Low Height, Light Weight NAS1329 12 Boeing Supp F Nut, Blind Rivet NAS1352 13 Screw, Cap, Socket Head, Undrill and Drilled, Plain and Self- Locking, Alloy Steel, Corrosion-Resistant Steel and Heat- Resistant Steel, UNRC-3A and UNRC-2A NAS1398 11 Boeing Supp AP Rivet-Blind, Protruding Head, Locked Spindle NAS1399 13 Boeing Supp E Rivet, Blind, 100º Flush Head, Locked Spindle NAS1400 7 Rivet, Blind, Self-Plugging, Mechanically Locked Spindle NAS1411 4 Stabilized 2022 - Band, Marker, Blank NAS1455 2 Chain, Weldless Flat Type Link NAS1463 5 Clip, Spring Tension NAS1464 6 Clip, Spring Tension NAS1473 13 Nut, Self-Locking, Plate, Two Lug, Cap, Floating NAS1474 11 Nut, Self-Locking, Plate-Two Lug, Cap…. NAS1514 3 Radiographic Standard For Classification of Fusion Weld Discontinuities NAS1578 14 Bolt, Shear, Flat Pan Head, Close Tolerance, Dovetail Slot, Offset Cruciform, and Offset Cruciform-Ribbed, Self-Locking and Nonlocking, 95 KSI Fsu NAS1580 16 Bolt, Shear, 100⁰ Flush Head, Offset Cruciform, Offset Cruciform - Ribbed and Dovetail Slot, 95 KSI FSU NAS1581 14 Bolt, Shear, 100⁰ Flush Reduced Head, Offset Cruciform, Offset Cruciform - Ribbed and Dovetail slot, 95 KSI Fsu NAS1595 3 INACTIVE See MIL-R-83248 NAS1611 12 Packing, Ethylene Propylene, Preformed O-Ring, Phosphate Ester Resistant (-65 °F to 250 /300 °F) NAS1638 3 INACTIVE Use AS4059 NAS1686 4 Rivet, Blind, Aluminum Sleeve, Mechanically Locked Spindle, Bulbed NAS1687 4 Rivet, Blind, Nickel-Copper and Nickel Alloy, Mechanically Locked Spindle, Bulbed NAS1760 7 Fitting End, Flareless Acorn, Standard Dimensions For NAS1766 4 Nut, Self-Locking, Plate, Corner, Counterbored, Floating, 125 KSI Ftu, 450 deg. F & 800 deg. F NAS1779 5 Nut, Self-Locking, Plate, Two Lug, Low Height C'Bored, Floating, Reduced Rivet Spacing, 160 KSI. . . NAS1789 3 Nut, Self-Locking, Plate, Side by Side, Floating, Low Height, Reduced Rivet Spacing, C'bored, 160 KSI, 450° F, 800°F NAS1791 5 Nut, Self-Locking, Plate - Two Lug, Floating, Variable Counterbore, Replaceable Nut Element 125 KSI Ftu, 450 Deg F and 800 Deg F. NAS1792 4 Nut, Self-Locking, Plate - One Lub, Floating, Variable Counterbore, Replaceable Nut Element 125KSI FTU, 450°F and 800°F NAS1793 5 Nut, Self-Locking, Plate, Corner, Floating, Variable Counterbore, Replaceable Nut Element, 125 KSI FTU, 450° F, 800°F NAS1801 4 Screw, Hex Head, Cruciform Recess, Full Thread, Alloy Steel, 160 KSI Ftu NAS1802 10 Screw, Hex Head, Cruciform Recess, Full Thread, A286 Cres, 160 KSI Ftu NAS1804 2 Nut, Self-Locking, Extended Washer, Double Hexagon, Alloy Steel, 180 KSI, 450 Deg F NAS1900 6 Rivet, Blind, General Purpose, Bulbed, Self Plugging, Mechanically-Locked-Spindle NAS1919 8 Rivet, Blind, General Purpose, Bulbed, Protruding Head, Mechanically-Locked-Spindle NAS1921 9 Rivet, Blind, General Purpose, Bulbed, 100 Degree Flush Head, Mechanically-Locked-Spindle NAS1922 6 Boeing Supp K Clamp, Hose, Band, Tangential Worm, Light Weight NAS1923 4 Clamp, Hose, Band, Tangential Worm, Light Weight NAS1924 5 Boeing Supp D Clamp, Hose NAS3350 7 Nut, Self-Locking, 450°F & 800°F, High Quality NAS3402 4 Bag, Transparent, Single Item NAS3404 4 Stabilized 2023 - Bag, Transparent, Individual Box NAS3408 4 Stabilized 2023 - Box, Unit, Cushioned NAS3415 3 INACTIVE for new design (no supersession) NAS3428 2 INACTIVE for new design (no supersession) NAS3447 3 INACTIVE for new design (no supersession) NAS3449 3 Hoses/Tubes, Preformed or Straight, Packaging NAS380 18 NAS Documents, Preparation and Maintenance, In The Inch System of Units NAS410 5 AMD 2 NAS Certification & Qualification of Nondestructive Test Personnel NAS412 3 Foreign Object Damage (FOD) Prevention Guidance Doc. NAS42 11 Spacer, Sleeve, Rivet NAS43 12 Boeing Supp N Spacer, Sleeve-Screw & Bolt NAS463 13 Boeing Supp F Nut Spacer, Plate, Plain NAS4003 13 Fastener, A286 Corrosion Resistant Alloy, Externally Threaded, 160 KSI Ftu, 95 KSI Fsu, 1000°F NAS4452 4 Stabilized 2023 - Pin, Crimp 100° Flush Shear Head NAS508 3 INACTIVE See MS20615 NAS509 8 Boeing Supp D Reaffirmed 2019 Nut, Drilled Jam NAS517 8 Boeing Supp F Screw-100° Close Tolerance NAS523 31 Fastener Code NAS538 11 Bushing, Flanged, Press Fit, Undersize Inside Diameter NAS561 11 Pins, Spring, Slotted & Coiled, Heavy Duty NAS591 7 Boeing Supp J 30M-NAS591(NEW) Stabilized 2022 - Coupling, Rigid Tube Connector, Aluminum NAS593 7 Boeing Supp C Reaffirmed 2023 - Nut, Rigid Tube Connector, Aluminum NAS594 7 Boeing Supp B Stabilized 2022 Coupling - Ridig Tube Connector, Corrosion Resistant Steel NAS596 7 Boeing Supp B Stabilized 2022 - Nut, Rigid Tube Connector, Cres NAS597 5 Fittings, Rigid Tube Connector, Flared Tube NAS600,NAS601,NAS603, NAS604,NAS605,NAS606 12 Screw, Machine, Pan Head, Cruciform Recess, Full Thread, Alloy Steel NAS6000,NAS6001,NAS6002, NAS6003 4 INACTIVE INACTIVE for new design (no supersession) NAS620 8 Washer, Flat, Reduced Outside Diameter NAS623 8 Screw, Shear, Pan Head, Alloy Steel, Cruciform Recess, Short Thread, 95 KSI Fsu NAS6603,NAS6604,NAS6605, NAS6606,NAS6607,NAS6608, NAS6609,NAS6610,NAS6611, NAS6612,NAS6613,NAS6614, NAS6615,NAS6616,NAS6617, NAS6618,NAS6619,NAS6620 10 Bolt, Tension, Hex Head, Close Tolerance, Alloy Steel, Long Thread, Reduced Major Dia., Self-Locking And Nonlocking, 160 KSI Ftu NAS6703,NAS6704,NAS6705, NAS6706,NAS6707,NAS6708, NAS6709,NAS6710,NAS6711, NAS6712,NAS6713,NAS6714, NAS6715,NAS6716,NAS6717, NAS6718,NAS6719,NAS6720 12 Boeing Supp AB Bolt, Hex Head, Close Tolerance, A286 Cres NAS680 10 INACTIVE Use MS21047 and MS21048 NAS686 13 INACTIVE See MS21059 and MS21060 NAS687 11 INACTIVE See MS21061 and MS21062 NAS688,NAS689,NAS690, NAS691,NAS692 9 INACTIVE See MS21063 and MS21064 NAS697 10 INACTIVE Use MS21069 and MS21070 NAS73 10 Bushing, Clamp-Up, Steel, Cadmium Plated NAS75 10 Boeing Supp A Bushing, Plain Press Fit, Steel or Cres NAS77 15 Bushing, Flanged, Press Fit Steel, Cres, Bronze and Copper NAS847 2 Caps & Plugs, Protective, Dust & Moisture Seal NAS850 7 Stabilized 2023 - General Packaging Standard NAS9301 7 Rivet, Blind, Protruding Head, Mechanically Locked Spindle, Bulbed, Style A, Class 1, Code B and E NAS9307 5 Rivet, Blind, Protruding Head, Mechanically Locked Spindle,Bulbed,Style A,Class 1,Code M NAS9308 5 Rivet, Blind, 100º Flush Heat, Mechanically Locked Spindle,Bulbed,Style A,Class2,Code M NAS9926 NC Stabilized 2023 - Nut, Self-Locking, 12 Point, A286 Cres, Low Height, 160 KSI Ftu, 450 deg. F NASM3THRU20 5 Boeing Supp B Boeing SL Supp 30M-NASM3THRU20 (NEW) Bolt, Machine, Aircraft NASM316 2 Nut, Jam, Hexagon NASM10971 1 Pin, Spring, Tubular, Coiled and Slotted NASM124731 thru NASM124770 includes NASM124736 3 Insert, Cres, helical Coil Fine Thread, 2 Dia Nominal Length NASM14200 4 Nut, Floating, Self-Locking, Attached Retention Element (A.R.E.), 450 ºF, Steel, 125 KSI Ftu, Replaceable Nut Element NASM16555 4 Pin, Straight, Headless, Dowel, .0002 Over Nominal Size NASM16562 2 Boeing Supp E Reaffirmed 2019 Pin, Spring, Tubular, Slotted NASM17984 2 Boeing Supp C Boeing SL Supp 30M-NASM17984(B) Pin, Quick Release, Self-Retaining, Positive Locking, Single Acting, Button Handle NASM21 thru NASM37 3 Bolt, Clevis NASM256 4 Nut, Self-Locking, Plate, Right Angle, 250 Deg F NASM20004 thru NASM20024 5 Bolts, Internal Wrenching, 160 KSI Ftu and 96 KSI Fsu NASM20426 3 Rivet, Solid, Countersunk 100, Alum and TI NASM20427 4 Rivet, Solid, 100º Countersunk Head, Carbon Steel, Corrosion- Resistant Steel, Nickel-Copper and Copper NASM20470 3 Boeing Supp B Boeing SL Supp 30M-NASM20470(B) Rivet, Solid, Universal Head, Aluminum Alloy and Titanium Columbium Alloy NASM20600 2 Rive, Blind, Structural Pull Stem, Self-Plugging, Protruding Head, Type II NASM20601 3 Boeing Supp A Rivet, Blind, Structural Pull Stem, Self-Plugging 100° Flush Head, Type II NASM20604 3 Boeing Supp D Boeing SL Supp 30M-NASM20604(NEW) Rivet, Blind, Non-Structural, Universal Head, Class 1 NASM20605 4 Rivets, Blind, Nonstructural, 100º Flush Head, Class 2 NASM20615 6 Boeing Supp C Rivet, Solid, Universal Head, Brass, Copper, Nickel-Copper Alloy NASM20995 2 Boeing Supp C Boeing SL Supp 30M-NASM20995(NEW) Wire, Safety or Lock NASM21042 3 Boeing Supp B Nut, Self-Locking, 450°F, Reduced Hexagon, Reduced Height, Ring Base, Non-Corrosion Resistant Steel NASM21043 3 Nut, Self-Locking, 800°F, Reduced Hexagon, Reduced Height, Ring Base, Cres NASM21047 4 Nut, Self-Locking, Plate, Two-Lug, Low Height, Steel, 125 KSI Ftu, 450° F NASM21048 3 Nut, Self-Locking, Plate, Two Lug, Low Height, Cres, 125 KSI Ftu, 450° F and 800° F NASM21055 2 Nut, Self-Locking, Plate, Corner, Low Height, Steel, 125 KSI Ftu, 450 Deg F NASM21056 2 Nut, Self-Locking, Plate, Corner, Low Height, Cres. . . NASM21058 3 Nut, Self-Locking, Plate, Corner, 100⁰ CSK, Low Height, Cres, 125 KSI Ftu, 450⁰ F & 800⁰ F NASM21059 3 Nut, Self-Locking, Plate, Two Lug, Floating, Low Height Steel, 125 KSI Ftu, 450° F NASM21060 3 Boeing Supp C Boeing SL Supp 30M-NASM21060(A) Nut, Self-Locking, Plate, Two Lug, Floating, Low Height, Cres, 125 KSI Ftu, 450 F & 800 F NASM21061 2 Nut, Self-Locking, Plate, One Lug, Floating, Low Height, Steel, 125 KSI Ftu, 450º F NASM21062 2 Nut, Self-Locking, Plate, One Lug, Floating, Low Height, Cres, 125 KSI Ftu, 450º F and 800º F NASM21064 1 Nut, Self-Locking Gang Channel, Floating, Low Height, Steel, 125 KSI Ftu, 450º F NASM21069 2 Boeing Supp B Boeing SL Supp 30M-NASM21069(NEW) Nut, Self-Locking, Plate, Two Lug, Reduced Rivet Spacing, Low Height, Steel, 125 KSI Ftu, 450º F NASM21070 2 Boeing Supp ORIG Boeing SL Supp 30M-NASM21070(A) Nut, Self-Locking, Plate, Two Lug, Reduced Rivet Spacing, Low Height, Cres, 125 KSI Ftu, 450º F and 800º F NASM21071 1 Nut, Self-Locking, Plate, One-Lug, Reduced Rivet Spacing, Low Height, Steel, 125 KSI Ftu, 450 deg F NASM21072 3 Nut, Self-Locking, Plate, One-Lug, Reduced Rivet Spacing, Low Height, Cres, 125 KSI Ftu, 450 deg F and 800 deg F NASM21073 3 Nut, Self-Locking, Plate, Corner, Reduced Rivet Spacing, Low Height, Steel, 125 KSI Ftu, 450 Degree NASM21074 2 Nut, Self-Locking, Plate, Corner, Reduced Rivet Spacing, Low Height, Cres, 125 KSI Ftu, 450º F and 800º F NASM21075 3 Boeing Supp D Boeing SL Supp 30M-NASM21075(A) Nut, Self-Locking, Plate, Two Lug, Floating, Reduced Rivet Spacing, Low Height, Steel, 125 KSI Ftu, 450º F NASM21076 4 Boeing Supp A Boeing SL Supp 30M-NASM21076(NEW) Nut, Self-Locking, Plate, Two Lug, Floating, Reduced Rivet Spacing, Low Height, Cres, 125 KSI Ftu, 450º F and 800º F NASM21077 3 Nut, Self-Locking, Plate, Two Lug, Floating, Non-Metallic Insert, Steel, 125 KSI Ftu, 250F NASM21143 2 Pin, Straight, Headless (Dowel), General Spec NASM21209 4 Boeing Supp D Boeing SL Supp 30M-NASM21209(C) Insert, Screw Thread, Coarse and Fine, Screw Locking, Helical Coil, Cres NASM21250 2 Bolt, Tension, Steel, External Wrenching, Flanged, 12-Point, 180 KSI Ftu, 450 Deg F NASM21266 3 Grommet, Plastic, Edging NASM21299 3 Washer, Countersunk and Plain NASM22529 3 Grommet, Edging NASM24665 2 Boeing Supp E Boeing SL Supp 30M-NASM24665(NEW) Pin, Cotter (Split) NASM24693 6 Screw, Machine, Flat Countersunk Head, 100°, Cross Recessed, UNC-2A & UNF-2A NASM24694 3 Screw, Machine, Flat Countersunk Head, 100°, Structural, Cross Recessed, UNC-3A & UNF-3A NASM25027 1 Nut, Self-Locking, 250 °F, 450 °F, and 800 °F NASM3036 3 Grommets, Rubber, Hot-Oil and Coolant Resistant NASM310 2 Boeing Supp A Nut, Plain, Castellated, Airframe NASM320 3 Nut, Plain, Castellated, Shear NASM33537 4 Insert, Screw Thread, Helical Coil. . . NASM33540 3 Safety Wiring And Cotter Pinning, NASM47196 3 Preparation For and Installation of Buck-Type Rivets NASM5674 2 Reaffirmed 2023 - Rivets, Structural, Aluminum Alloy, Titanium Columbium Alloy, General Specification for NASM6812 4 Reaffirmed 2023 - Fasteners, Externally Threaded, Alloy Steel, Corrosion Resistant Steel, Aluminum, 60,000 PSI to 125,000 PSI NASM63540 1 Stud, Self-Clinching General Specification For NASM7838 4 Bolt, Internal Wrenching, 160 KSI Ftu NASM81177/1 1 Stabilized 2023 Fasteners, Blind, High Strength, Installation Formed, Alloy Steel: Design & Usage Limits of NASM8814 2 Rivets, Blind, Nonstructural Type NASM8831 5 Reaffirmed 2023 - Fasteners, Alloy Steel, 450 °F Externally Threaded. . . NASM8846 2 180 KSI Ftu, 108 KSI Fsu, FATIGUE RATED ORKAL ATP-100 D Acceptance Test Procedure for Water Tank Orkal Part Number BT100-3-1 PARKER ES5-117 G Visual Standard P-103-90 C Material Protection P-108-1 L Inspection of Tubes and Tube Assemblies P-110-04 E Machined Details Definitions and Limits P1090 Y Process Control Procedure for Type II and Type VI Passivation Treatments P9.1-1 A General Workmanship Standard PATS AIRCRAFT PS-1 C OBSOLETE Replaced by PS-001 Gas Tungsten Arc & Resistance Welding PS-013 M Instructing. For the Surface Treatment and Application of Chrome Conversion coating of Alum. And Alum. Alloys PS-15 C Penetrant inspection PS-2 A Standard Design & Mfg Processes PS-2-1 A OBSOLETE Replaced by PS-002-1 Marking and Labeling - STC PMA Parts PS-24 C Epoxy White, Painting Instructions PS-29 A Cleaning & Priming For Structural Alum Bonding PS-3 F Sealing - Fuel Tank, Fastener & Wire Bundle PS-7 K Preparation & Application of Coatings & Primers TO-767 ORIG Installation Of Gamah Tube End Fittings TO-953 M Compilation of Interchangeable Fuel System Parts PMA PRODUCTS, INC. 45.15-1 3 Marking of Replacement Parts PPG AEROSPACE CA8800 Issue 2/15 Buffable Polyurethane Topcoats RATIER-FIGEAC PRO-RF-0009 Ver 02 Procedure: Controlling Corrective and Preventative Actions PRO-RF-0020 Ver 10 Procedure: Controlling Nonconforming Product PRO-RF-0080 Ver 07 Performing A First Article Inspection PRO-RF-0204 Ver 06 Control of CTQ (Critical to Quality) Parts SARGENT FLETCHER MPP-009 E Tube Fabrication PD434001 G Solid and Blind Rivets, Installation of PD434004 K Non-Aqueous Penetrant Inspection Procedure for PD434011 ORIG Wet Installation of Fasteners and Corrosion Prevention Using Primer and Sealant PD434017 H Painting Requirements, KC46 Centerline Drogue System (CDS) Hose Reel, Process Specification For. . . PD434019 D Installation of Adhesive Bonded Fasteners, Procedure For PD434021 A Roller Swage Bearing, Installation and Retention, Process Specification For PD434022 D Bonding and Grounding Requirements for KC-46 CDS, Process Specification for PD434023 B Corrosion Prevention Using Primer and Sealant for KC-46 CDS, Process Specification for PD434026 A Threaded Pin-Rivet Fasteners, Process Specification For PD434046 ORIG Grading and Control of Parts And Assemblies For Non- Destructive Testing and Inspection PS434047 ORIG Installation of Spiral Retaining Rings PD434048 J Manufacture of FR600-84MDR, Processes and Standards Directory For PD434050 A Solvent Cleaning And Surface Preparation PD434055 NC Tube Bending, Process Requirements for PD434065 NC Application of Adhesive Backed Labels PD434070 B Pressure Test Requirements For FR600-84MDR Nitrogen, Fuel and Hydraulic Tubes and Hoses PD439001 D Acceptance Test Procedure for Modified MXU- 648 POD PD439005 C Outer Rib Assembly, Acceptance Test Procedure For PD439022 B T-6/AT-6 65 Gallon Auxiliary Tank Assembly, Acceptance Test Procedure For PD439030 B Variable Speed Drogue, Acceptance Test Procedure for Composite Springs PS4001 B Finish & Coating for F-2 Fuel Tank PS410 G Painting Requirements, FR300 Hose Reel Assembly, Process Specification for PS421 C Process Specification PS428 R Finishing & Coating F-16 Fuel Tank F-16 Pylon Assembly PS429 B Finishing & Coating 600 Gallon Tank Assembly PS432 J Painting Requirements, FR600 Hose Reel Assembly, Process Specification for PS434 G Finish and Coating, Model 48-000, Process Specification For PS518 C Identification & Marking Of Aeronautical Equipment, Assemblies Subassemblies And Parts For Use By The Armed Services PS76 F Inspection Criteria For Flareless Tube Fittings PS90 F OBSOLETE Superseded by PD434006 Welding of Aluminum Alloys By Inert Gas Shielded Method PS93-1039 C Installation Standard Mechanical Attachment of Swage Type Ferrules to Tubing P99 ORIG Nital Etch Inspection of Steel Parts QCI4015 AC Inspection and Control of Chemical Conversion Coating and Painting Report No 95 C Standards for Aluminum Fuel Tank Welding SP436125 ORIG Classification of Characteristics, Specification for ST437003 D Manufacturing Quality, Standard For SENIOR AEROSPACE MS-0065 NR Acceptance Criteria For Perforated Metal SIERRACIN/ HARRISON TIB1229 A Acceptance Criteria For Perforated Metal SIERRA NEVADA CORP. IMS-PS-000 A Aviation Production Assembly and Installation SNOW ENGINEERING PS103 8/10/2005 Epoxy Primer and Polyester Urethane Top Coat PS120 3/20/2004 Welding 4130 Steel PS121 4/11/1989 Certification of Welders PS122 7/25/1997 Welding Stainless Steel PS132 7/16/1996 Fabrication, Beading, Flaring of Tubing SPACEX NDT-00000002 1 NDE Personnel Qualification NDT-PT-00000001 4 Penetrant Testing (PT) General Specification NDT-VT-00000001 1 Visual Testing (VT) General Specification SPD-00000394 4 Starship Tube & Pipe Welding Process Spec SPD-00000533 6 Starship Dome Lap Weld Inspection Criteria SPD-00000608 2 General Welding & Inspection Requirements for Starship Vehicles SPD-00035971 7 Contingent Rework for Tube Assembly Flanges SPX-00000663 8 Starship Welder Qualification Procedure SPX-00000908 2 Cold Worked 304L Stainless Steel SPX-00001064 9 Starship Weld & Parent Inspection Criteria SPX-00001313 7 Removal of EDM Recast Layer & Pre-Penetrant Inspection Etching SPX-00001892 7 MFG & Quality Guidelines for T3/Numeric Components SPX-00003695 ORIG How We Clean: Guiding Principles SPX-00003976 1 Starship Hi/Lo Alternate Acceptance Criteria SPX-00006876 27 Component Precision Cleaning Specification SPX-00034906 10 Manufacturing Development Program SPIRIT AEROSYSTEMS 1TD1379T00001-1001 L Burst Pressure Testing for Transport Elements MAA1-10009-1 L Quality Assurance Standard for Digital Product Definition at Spirit AeroSystems, Inc. Suppliers MAA1-10034-1 E Supplier Nonconformance MAA1-10041-1 N Packaging and Shipping Requirements For Spirit Aerosystems, Inc. Supp