Garmin G1000 NXi Cockpit Reference Guide for the da62

WaRNING: Do not use data link weather information for maneuvering in, near, or around areas of hazardous weather. Information contained within data link weather products may not accurately depict current weather conditions. WaRNING: Do not use the indicated data link weather product age to determine the age of the weather information shown by the data link weather product. Due to time delays inherent in gathering and processing weather data for data link transmission, the weather information shown by the data link weather product may be older than the indicated weather product age. WaRNING: Do not use terrain avoidance displays as the sole source of information for maintaining separation from terrain and obstacles. Garmin obtains terrain and obstacle data from third party sources and cannot independently verify the accuracy of the information. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A Warnings, Cautions & Notes WaRNING: Do not rely on the displayed minimum safe altitude (MSAs) as the sole source of obstacle and terrain avoidance information. Always refer to current aero- nautical charts for appropriate minimum clearance altitudes. WaRNING: Do not use GPS to navigate to any active waypoint identified as a ‘NON WGS84 WPT’ by a system message. ‘NON WGS84 WPT’ waypoints are derived from an unknown map reference datum that may be incompatible with the map reference datum used by GPS (known as WGS84) and may be positioned in error as displayed. WaRNING: Do not rely on the autopilot to level the aircraft at the MDA/DH when flying an approach with vertical guidance. The autopilot will not level the aircraft at the MDA/DH even if the MDA/DH is set in the altitude preselect. WaRNING: Do not rely on the accuracy of attitude and heading indications in the following geographic areas (due to variations in the earth’s magnetic field): North of 72° North latitude at all longitudes; South of 70° South latitude at all longitudes; North of 65° North latitude between longitude 75° W and 120° W. (Northern Canada); North of 70° North latitude between longitude 70° W and 128° W. (Northern Canada); North of 70° North latitude between longitude 85° E and 114° E. (Northern Russia); South of 55° South latitude between longitude 120° E and 165° E. (Region south of Australia and New Zealand). WaRNING: Use appropriate primary systems for navigation, and for terrain, obstacle, and traffic avoidance. Garmin SVT is intended as an aid to situational awareness only and may not provide either the accuracy or reliability upon which to solely base decisions and/or plan maneuvers to avoid terrain, obstacles, or traffic. WaRNING: Do not use the Garmin SVT runway depiction as the sole means for determining the proximity of the aircraft to the runway or for maintaining the proper approach path angle during landing. WaRNING: Do not operate the weather radar in a transmitting mode when personnel or objects are within the MPEL boundary. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A Warnings, Cautions & Notes WaRNING: Always position the weather radar gain setting to Calibrated for viewing the actual intensity of precipitation. Changing the gain in weather mode causes pre- cipitation intensity to be displayed as a color not representative of the true intensity. WaRNING: Do not consider the overflight of thunderstorms to be safe, as extreme turbulence may exist significantly above observed returns. WaRNING: Do not rely on information from the reactive wind shear detection system display as the sole basis for detecting wind shear conditions. The system cannot predict the conditions in which wind shear is likely to develop. WaRNING: Do not rely only on the Turbulence Detection function for hazardous weather avoidance, or to maneuver in, near, or around areas of hazardous weather. WaRNING: Do not rely on information from a lightning detection system display as the sole basis for hazardous weather avoidance. Range limitations and interference may cause the system to display inaccurate or incomplete information. Refer to docu- mentation from the lightning detection system manufacturer for detailed information about the system. WaRNING: Do not use TAWS information for primary terrain or obstacle avoidance. TAWS is intended only to enhance situational awareness. WaRNING: Do not rely solely upon the display of traffic information for collision avoidance maneuvering. The traffic display does not provide collision avoidance resolution advisories and does not under any circumstances or conditions relieve the pilot’s responsibility to see and avoid other aircraft. CaUTIoN: Do not clean display surfaces with abrasive cloths or cleaners containing ammonia. They will harm the anti-reflective coating. CaUTIoN: Do not allow repairs to be made by anyone other than an authorized Garmin service center. Unauthorized repairs or modifications could void both the warranty and affect the airworthiness of the aircraft. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A Warnings, Cautions & Notes CaUTIoN: Never disconnect power to the system when loading a database. Power interruption during the database loading process could result in maintenance being required to reboot the system. CaUTIoN: Avoid areas on the display that appear “shadowed” (gray). The accuracy of the intensity of returns in the shaded areas should be treated as suspect. Exercise extreme caution, making maneuvering decisions with this information in mind. CaUTIoN: In Standby mode, the radar antenna is parked at the center line. It is always a good idea to put the radar in Standby mode before taxiing the aircraft to prevent the antenna from bouncing on the bottom stop and possibly causing damage to the radar assembly. NoTE All visual depictions contained within this document, including screen images of the system panel and displays, are subject to change and may not reflect the most current system and aviation databases. Depictions of equipment may differ slightly from the actual equipment. NoTE: Do not rely solely upon data link services to provide Temporary Flight Restric- tion (TFR) information. Always confirm TFR information through official sources such as Flight Service Stations or Air Traffic Control. NoTE: The United States government operates the Global Positioning System and is solely responsible for its accuracy and maintenance. The GPS system is subject to changes which could affect the accuracy and performance of all GPS equipment. Portions of the system utilize GPS as a precision electronic NAVigation AID (NAVAID). Therefore, as with all NAVAIDs, information presented by the system can be misused or misinterpreted and, therefore, become unsafe. NoTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NoTE: Use of polarized eyewear may cause the flight displays to appear dim or blank. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A Warnings, Cautions & Notes NoTE: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This notice is being provided in accordance with California’s Proposition 65. If you have any questions or would like additional information, please refer to our web site at www.garmin.com/prop65. NoTE: Operating the system in the vicinity of metal buildings, metal structures, or electromagnetic fields can cause sensor differences that may result in nuisance mis- compare annunciations during start up, shut down, or while taxiing. If one or more of the sensed values are unavailable, the annunciation indicates no comparison is possible. NoTE: The system responds to a terminal procedure based on data coded within that procedure in the Navigation Database. Differences in system operation may be observed among similar types of procedures due to differences in the Navigation Database coding specific to each procedure. NoTE: The FAA has asked Garmin to remind pilots who fly with Garmin database- dependent avionics of the following: • It is the pilot’s responsibility to remain familiar with all FAA regulatory and advisory guidance and information related to the use of databases in the National Airspace System. • Garmin equipment will only recognize and use databases that are obtained from Garmin or Jeppesen. Databases obtained from Garmin or Jeppesen that have a Type 2 Letter of Authorization (LOA) from the FAA are assured compli- ance with all data quality requirements (DQRs). A copy of the Type 2 LOA is available for each applicable database and can be viewed at http://fly.garmin. com by selecting ‘Aviation Database Declarations.’ • Use of a current Garmin or Jeppesen database in your Garmin equipment is required for compliance with established FAA regulatory guidance, but does not constitute authorization to fly any and all terminal procedures that may be presented by the system. It is the pilot’s responsibility to operate in accor- dance with established pertinent aircraft documents and regulatory guidance or limitations as applicable to the pilot, the aircraft, and installed equipment. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A Warnings, Cautions & Notes NoTE: The pilot/operator must review and be familiar with Garmin’s database exclusion list as discussed in SAIB CE-14-04 to determine what data may be incomplete. The database exclusion list can be viewed at www.flygarmin.com by selecting ‘Database Exclusions List.’ NoTE: The pilot/operator must have access to Garmin and Jeppesen database alerts and consider their impact on the intended aircraft operation. The database alerts can be viewed at www.flygarmin.com by selecting ‘Aviation Database Alerts.’ NoTE: Garmin requests the flight crew report any observed discrepancies related to database information. These discrepancies could come in the form of an incorrect procedure; incorrectly identified terrain, obstacles and fixes; or any other displayed item used for navigation or communication in the air or on the ground. Go to FlyGarmin. com and select ‘Aviation Data Error Report’. NoTE: Electronic aeronautical charts displayed on this system have been shown to meet the guidance in AC 120-76D as a Type B Electronic Flight Bag (EFB) for FliteCharts and ChartView. The accuracy of the charts is subject to the chart data provider. Own-ship position on airport surface charts cannot be guaranteed to meet the accuracy speci- fied in AC 120-76D. Possible additional requirements may make a secondary source of aeronautical charts, such as traditional paper charts or an additional electronic display, necessary on the aircraft and available to the pilot. If the secondary source of aeronautical charts is a Portable Electronic Device (PED), its use must be consistent with the guidance in AC 120-76D. NoTE: The navigation databases used in Garmin navigation systems contain Special Procedures. Prior to flying these procedures, pilots must have specific FAA authoriza- tion, training, and possession of the corresponding current, and legitimately-sourced chart (approach plate, etc.). Inclusion of the Special Procedure in the navigation database DOES NOT imply specific FAA authorization to fly the procedure. NoTE: Terrain and obstacle alerting is not available north of 89º North latitude and south of 89º South latitude. This is due to limitations present within the Terrain database and the system’s ability to process the data representing the affected areas. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A Warnings, Cautions & Notes NoTE: The nose of the ‘own ship’ symbol represents the location of the aircraft. The center of any traffic symbol represents the location of that traffic. The traffic and own ship symbols are an abstract representation and do not reflect the physical extent of the aircraft/traffic, and should not replace other methods for identifying traffic. NoTE: Intruder aircraft at or below 500 ft. AGL may not appear on the Garmin SVT display or may appear as a partial symbol. NoTE: Interference from GPS repeaters operating inside nearby hangars can cause an intermittent loss of attitude and heading displays while the aircraft is on the ground. Moving the aircraft more than 100 yards away from the source of the interference should alleviate the condition. NoTE: Operate G1000 NXi system power through at least one cycle in a period of four days of continuous operation to avoid an autonomous system reboot. NoTE: The purpose of this Cockpit Reference Guide is to provide the pilot a resource with which to find operating instructions on the major features of the system more easily. It is not intended to be a comprehensive operating guide. Complete operating procedures for the system are found in the Pilot’s Guide for this aircraft. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A Warnings, Cautions & Notes Blank Page Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A Software License agreement SoFTWaRE LICENSE aGREEMENT BY USING THE DEVICE, COMPONENT OR SYSTEM MANUFACTURED OR SOLD BY GARMIN (“THE GARMIN PRODUCT”), YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY. Garmin Ltd. and its subsidiaries (“Garmin”) grants you a limited license to use the software embedded in the Garmin Product (the “Software”) in binary executable form in the normal operation of the Garmin Product. Title, ownership rights, and intellectual property rights in and to the Software remain with Garmin and/or its third-party providers. You acknowledge that the Software is the property of Garmin and/or its third-party providers and is protected under the United States of America copyright laws and international copyright treaties. You further acknowledge that the structure, organization, and code of the Software are valuable trade secrets of Garmin and/or its third-party providers and that the Software in source code form remains a valuable trade secret of Garmin and/or its third-party providers. You agree not to reproduce, decompile, disassemble, modify, reverse assemble, reverse engineer, or reduce to human readable form the Software or any part thereof or create any derivative works based on the Software. You agree not to export or re-export the Software to any country in violation of the export control laws of the United States of America. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A Software License agreement Blank Page Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 13 Record of Revisions Record of Revisions Part Number Revision date Page Range description 190-02622-00 A 09/06/2019 All Production Release at GDU 20.89 Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 14 Record of Revisions Blank Page Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A i Table of Contents FLIGHT INSTRUMENTS FLIGHT INSTRUMENTS.......................................................................................1 airspeed Indicator ............................................................................................................1 altimeter ..........................................................................................................................2 Horizontal Situation Indicator (HSI) ..................................................................................3 Course deviation Indicator (CdI) ......................................................................................4 SUPPLEMENTaL FLIGHT daTa ............................................................................5 Wind data .........................................................................................................................5 GaRMIN SyNTHETIC VISIoN TECHNoLoGy (SVT) .................................................5 SVT operation ..................................................................................................................5 Field of View .....................................................................................................................6 PFd aNNUNCIaTIoNS aNd aLERTING FUNCTIoNS ...............................................6 ENGINE INdICaTIoN SySTEM (EIS) EIS dISPLay .....................................................................................................7 ENGINE PaGE ...................................................................................................8 Fuel Calculations ............................................................................................................10 aUdIo PaNEL aNd CNS CoM oPERaTIoN ............................................................................................11 NaV oPERaTIoN .............................................................................................12 NaV Radio Selection and activation ...............................................................................12 adF/dME Tuning .............................................................................................................12 ModE S TRaNSPoNdER ..................................................................................13 Flight Id Reporting .........................................................................................................14 addITIoNaL aUdIo PaNEL FUNCTIoNS ............................................................14 Intercom .........................................................................................................................14 Blue-Select Mode (Telephone/Entertainment distribution) ............................................15 Bluetooth .......................................................................................................................16 aUdIo PaNEL PREFLIGHT PRoCEdURE .............................................................16 Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A ii Table of Contents FLIGHT MaNaGEMENT Navigation Status Box aNd data Bar .............................................................................19 USING MaP dISPLayS .....................................................................................19 Map orientation .............................................................................................................19 Map Range .....................................................................................................................20 Map Panning ...................................................................................................................20 Measuring Bearing and distance ....................................................................................21 Topography .....................................................................................................................21 Map Symbols ..................................................................................................................22 airways...........................................................................................................................23 additional Navigation Map Items...................................................................................24 WayPoINTS ...................................................................................................25 airports ..........................................................................................................................25 Non-airport Waypoints ...................................................................................................26 Nearest airspace.............................................................................................................30 Smart airspace ...............................................................................................................30 dIRECT-To-NaVIGaTIoN ..................................................................................31 FLIGHT PLaNNING ..........................................................................................33 Flight Plan Views ............................................................................................................33 Creating a Flight Plan .....................................................................................................33 Flight Plan Waypoint and airway Modifications .............................................................34 Flight Plan operations ....................................................................................................39 Managing Flight Plans ....................................................................................................42 VERTICaL NaVIGaTIoN ...................................................................................49 Constraints .....................................................................................................................50 Vertical Situation display (VSd)......................................................................................52 Vertical Navigation direct To ..........................................................................................53 departures ......................................................................................................................54 arrivals ..........................................................................................................................56 approaches ....................................................................................................................58 TRIP PLaNNING ..............................................................................................63 RaIM (RECEIVER aUToNoMoUS INTEGRITy MoNIToRING) PREdICTIoN .............64 Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A iii Table of Contents HaZaRd aVoIdaNCE daTa LINK WEaTHER.......................................................................................67 activating the SiriusXM Weather Service .......................................................................67 Weather Product age ......................................................................................................69 displaying data Link Weather Products ..........................................................................71 Connext Weather data Requests ....................................................................................74 Weather Product overview .............................................................................................75 FIS-B Weather Status ......................................................................................................83 SToRMSCoPE® LIGHTNING dETECTIoN SySTEM ................................................83 Using the Stormscope Page ............................................................................................83 additional Stormscope displays .....................................................................................84 Stormscope abnormal operations ..................................................................................85 aIRBoRNE CoLoR WEaTHER RadaR ................................................................86 Basic antenna Tilt and Range Setup ..............................................................................86 Weather Radar operation ...............................................................................................89 Ground Mapping and Interpretation ..............................................................................92 additional Weather Radar displays ................................................................................93 TERRaIN dISPLayS .........................................................................................94 VERTICaL SITUaTIoN dISPLay (VSd) TERRaIN...................................................95 TRaFFIC INFoRMaTIoN SERVICE (TIS) ..............................................................96 displaying Traffic data ....................................................................................................97 aVIdyNE TaS600 TRaFFIC................................................................................98 System Test ...................................................................................................................100 operation .....................................................................................................................100 adS-B TRaFFIC .............................................................................................102 operation .....................................................................................................................103 aUToMaTIC FLIGHT CoNTRoL SySTEM oVERVIEW ...................................................................................................107 Basic autopilot operation ............................................................................................107 FLIGHT dIRECToR oPERaTIoN .......................................................................108 activating the Flight director .......................................................................................108 Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A iv Table of Contents aFCS ModES................................................................................................109 Vertical Modes..............................................................................................................109 Lateral Modes ...............................................................................................................109 Combination modes......................................................................................................110 addITIoNaL FEaTURES SaFETaXI (oPTIoNaL) ...................................................................................113 ELECTRoNIC CHaRTS ....................................................................................113 FliteCharts ....................................................................................................................114 ChartView .....................................................................................................................115 IFR/VFR Charts ..............................................................................................................116 SaTELLITE TELEPHoNE aNd daTaLINK SERVICES (oPTIoNaL) ...........................117 Registering the System with Garmin Connext ..............................................................117 disable/Enable Iridium Transceiver ...............................................................................117 Contacts .......................................................................................................................117 Telephone Communication ...........................................................................................118 Text Messaging (SMS) ...................................................................................................121 CoNNEXT SETUP (oPTIoNaL) ........................................................................126 SIRIUSXM RadIo (oPTIoNaL) ........................................................................127 activating SiriusXM Satellite Radio Services ................................................................127 Using SiriusXM Radio ...................................................................................................128 ELECTRoNIC CHECKLISTS ..............................................................................129 aUXILIaRy VIdEo .........................................................................................130 Video Setup ..................................................................................................................130 ELECTRoNIC STaBILITy aNd PRoTECTIoN (oPTIoNaL) ....................................131 database Cycle Number and Revisions .........................................................................131 CREW PRoFILES............................................................................................132 SCHEdULER..................................................................................................135 aBNoRMaL oPERaTIoN REVERSIoNaRy ModE ..................................................................................137 aBNoRMaL GPS CoNdITIoNS .......................................................................137 SVT TRoUBLESHooTING ................................................................................138 Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A v Table of Contents UNUSUaL aTTITUdES ....................................................................................139 SVT Unusual attitudes ..................................................................................................140 aBNoRMaL CoM oPERaTIoN ........................................................................141 Stuck Microphone.........................................................................................................141 CoM Tuning Failure .......................................................................................................141 audio Panel Fail-Safe operation ...................................................................................141 REVERSIoNaRy ModE ..................................................................................141 dEad RECKoNING NaVIGaTIoN ....................................................................141 SUSPECTEd aUToPILoT MaLFUNCTIoN ..........................................................142 overpowering autopilot Servos ...................................................................................142 GdL 69a SXM TRoUBLESHooTING .................................................................143 GdL 69a SXM Radio .....................................................................................................143 aNNUNCIaTIoNS aNd aLERTS SySTEM aNNUNCIaTIoNS .............................................................................145 CaS MESSaGES ............................................................................................147 Warning Messages ........................................................................................................147 Caution Messages.........................................................................................................148 advisory Messages .......................................................................................................149 VoICE aLERTS ..............................................................................................149 SySTEM MESSaGES ......................................................................................150 FLIGHT PLaN IMPoRT/EXPoRT MESSaGES ......................................................161 FIS-B STaTUS MESSaGES ...............................................................................162 CoNNEXT WEaTHER MESSaGES .....................................................................163 aIRBoRNE WEaTHER RadaR aNNUNCIaTIoNS................................................165 TERRaIN aNNUNCIaTIoNS ............................................................................166 Terrain-SVT annunciations ............................................................................................166 TRaFFIC aNNUNCIaTIoNS .............................................................................167 TIS annunciations .........................................................................................................167 TaS annunciations ........................................................................................................169 adS-B Traffic annunciations..........................................................................................170 audio alerts ..................................................................................................................173 Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A vi Table of Contents aPPENdIX daTaBaSE MaNaGEMENT .............................................................................175 Loading Updated databases .........................................................................................175 Updating databases Using an Supplemental data (Sd) card ........................................176 Update databases Using the Wireless Transceiver ........................................................177 database deletion Feature .........................................................................................182 Magnetic Field Variation database Update ..................................................................182 MaP SyMBoLS .............................................................................................183 Miscellaneous Map Symbols .........................................................................................183 Land Symbols ...............................................................................................................184 aviation Symbols ........................................................................................................185 airspace Symbols .........................................................................................................186 airways.........................................................................................................................187 Flight Plan Leg Symbols................................................................................................187 obstacle Symbols .........................................................................................................188 INdEX Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 1 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index FLIGHT INSTRUMENTS FLIGHT INSTRUMENTS aIRSPEEd INdICaToR Enabling/disabling and modifying Vspeed bugs: 1) Press the TMR/REF Softkey to show the ‘References’ Window. 2) Turn the large FMS Knob to highlight the desired vspeed bug value. 3) Turn the small FMS Knobs to adjust the value for the selected vspeed bug. 4) Turn the large FMS Knob to highlight the ON/OFF field. 5) Turn the small FMS Knob clockwise to ON or counterclockwise to OFF. 6) To remove the window, press the CLR Key or the TMR/REF Softkey. Enabling/disabling or restoring default values to all vspeed bugs as a group: 1) Press the TMR/REF Softkey. 2) Press the MENU Key. 3) Turn the FMS Knob to highlight ‘All References On’, ‘All References Off’, or ‘Restore Defaults. 4) Press the ENT Key. 5) To remove the window, press the CLR Key or the TMR/REF Softkey. Setting the generic timer: 1) Press the TMR/REF Softkey. 2) Turn the large FMS Knob to select the timer field (HH:MM:SS). 3) Use the FMS Knob to enter the desired time. 4) Press the ENT Key. The Up/Dn field is now highlighted. 5) Turn the small FMS Knob to display the ‘UP/DOWN’ Window. 6) Turn the small FMS Knob to select ‘Up’ or ‘Dn’. 7) Press the ENT Key. ‘Start?’ is now highlighted. 8) Press the ENT Key to start the timer. The field changes to ‘Stop?’. If the timer is counting DOWN, it will start counting UP after reaching zero. 9) To stop the timer, press the ENT Key with ‘Stop?’ highlighted. The field changes to ‘Reset?’. 10) To reset the timer, press the ENT Key with ‘Reset?’ highlighted. The field changes back to ‘Start?’ and the digits are reset. 11) To remove the window, press the CLR Key or the TMR/REF Softkey. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 2 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index aLTIMETER Setting the Selected altitude: Turn the aLT Knob to set the Selected Altitude. Turn the large knob for 1000-ft increments, small knob for 100-ft increments. If set to Metric mode, the large knob adjusts the Selected Altitude in 500-meter increments; the small knob adjusts the Selected Altitude in 50-meter increments.. If a Minimum Descent Altitude/Decision Height (MDA/DH) value has been set, this altitude is also available for the Selected Altitude. displaying altitude in meters: 1) Press the PFd opt Softkey to display the second-level softkeys. 2) Press the aLT Units Softkey. 3) Press the Meters Softkey to turn on metric altitude readouts. 4) Press the Back Softkey twice to return to the top-level softkeys. WaRNING: Do not use a QFE altimeter setting with this system. System functions will not operate properly with a QFE altimeter setting. Use only a QHN altimeter setting for the height above mean sea level, or the standard pressure setting, as applicable. Selecting the altimeter barometric pressure setting: Turn the BaRo Knob to select the desired setting. Selecting standard barometric pressure (29.92 in Hg): 1) Press the PFd opt Softkey to display the second-level softkeys. 2) Press the STd Baro Softkey. Changing altimeter barometric pressure setting units: 1) Press the PFd opt Softkey to display the second-level softkeys. 2) Press the aLT Units Softkey. 3) Press the IN Softkey to display the barometric pressure setting in inches of mercury (in Hg). or: Press the HPa Softkey to display the barometric pressure setting in hectopascals (hPa). 4) Press the Back Softkey twice to return to the top-level softkeys. Setting the Baro Transition alert: 1) Use the FMS Knob to select the ‘Aux - System Setup 1’ Page on the MFD. 2) Push the FMS Knob to activate the cursor. 3) To enable/disable the Baro Transition Alert based on altitude, turn the large FMS Knob to highlight the ‘On’ or ‘Off’ field for the BARO Transition Alert Altitude in the BARO Transition Alert Box. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 3 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 4) If desired, turn the small FMS Knob to set the BARO Transition Alert Altitude On or Off. 5) Turn the large FMS Knob to highlight the Altitude field. 6) Use the FMS Knob to change the altitude and press the ENT Key to accept or press the CLR Key to return to the previous altitude selection. 7) Turn the large FMS Knob to highlight the ‘On’ or ‘Off’ field for the BARO Transition Alert Level. 8) If desired, turn the small FMS Knob to set the BARO Transition Alert Flight Level On or Off. 9) Turn the large FMS Knob to highlight the Flight Level field. 10) Use the FMS Knob to change the Flight Level for the alert and press the ENT Key to accept or press the CLR Key to return to the previous altitude selection. 11) Push the FMS Knob to deactivate the cursor. HoRIZoNTaL SITUaTIoN INdICaToR (HSI) Enabling/disabling the HSI Map on the PFd: 1) Press the Map/HSI Softkey. 2) Press the Layout Softkey. 3) Press the HSI Map Softkey to enable the HSI Map. or: Press the Map off Softkey to disable the HSI Map. adjusting the Selected Heading: Turn the HdG Knob to set the Selected Heading. Push the HdG Knob to synchronize the bug to the current heading. adjusting the Selected Course: Turn the CRS Knob to set the Selected Course. Push the CRS Knob to re-center the CDI and return the course pointer to the bearing of the active waypoint or navigation station. Changing the navigation angle true/magnetic setting: 1) Use the FMS Knob to select the ‘Aux - System Setup 1’ Page on the MFD. 2) Press the FMS Knob to activate the cursor. 3) Turn the large FMS Knob to highlight Nav Angle in the ‘Display Units’ Box. 4) Turn the small FMS Knob to highlight the desired setting and press the ENT Key. • True - References angles to true north (T). • Magnetic - Angles corrected to the computed magnetic variation (Mag Var). Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 4 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Selecting bearing display and changing sources: 1) Press the PFd opt Softkey. 2) Press either Bearing 1 or Bearing 2 Softkey to display the desired bearing pointer and information window with a NAV source. 3) Press either Bearing 1 or Bearing 2 Softkey again to change the bearing source to GPS. 4) Press either Bearing 1 or Bearing 2 Softkey a third time to change the bearing source to ADF. 5) To remove the bearing pointer and information window, press either Bearing 1 or Bearing 2 Softkey again. displaying the dME Information Window: 1) Press the PFd opt Softkey. 2) Press the dME Softkey to display the ‘DME Information’ Window above the ‘BRG1 Information’ Window. 3) To remove the ‘DME Information’ Window, press the dME Softkey again. CoURSE dEVIaTIoN INdICaToR (CdI) Changing navigation sources: 1) Press the CdI Softkey to change from GPS to VOR1 or LOC1. This places the cyan tuning box over the NAV1 standby frequency in the upper left corner of the PFD. 2) Press the CdI Softkey again to change from VOR1 or LOC1 to VOR2 or LOC2. This places the cyan tuning box over the NAV2 standby frequency. 3) Press the CdI Softkey a third time to return to GPS. Changing the selected GPS CdI setting: 1) Use the FMS Knob to select the ‘Aux - System Setup 1’ Page on the MFD. 2) Push the FMS Knob to activate the cursor. 3) Turn the large FMS Knob to highlight Selected in the GPS CDI box. 4) Turn the small FMS Knob to highlight the desired setting and press the ENT Key. 5) To cancel the selection, press the FMS Knob or the CLR Key. Enabling/disabling oBS Mode while navigating a GPS flight plan: 1) Press the oBS Softkey to select OBS Mode. 2) Turn the CRS Knob to select the desired course to/from the waypoint. Push the CRS Knob to synchronize the Selected Course with the bearing to the next waypoint. 3) Press the oBS Softkey again to return to automatic waypoint sequencing. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 5 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index SUPPLEMENTaL FLIGHT daTa WINd daTa displaying wind data: 1) Press the PFd opt Softkey. 2) Press the Wind Softkey to display wind data to the left of the HSI. 3) Press one of the option softkeys to change how wind data is displayed: • option 1: Headwind/tailwind and crosswind arrows with numeric speed components. • option 2: Wind direction arrow and speed. • option 3: Wind direction arrow with headwind/tailwind and crosswind components. 4) To remove the window, press the off Softkey. GaRMIN SyNTHETIC VISIoN TECHNoLoGy (SVT) WaRNING: Use appropriate primary systems for navigation, and for terrain, obstacle, and traffic avoidance. SVT is intended as an aid to situational awareness only and may not provide either the accuracy or reliability upon which to solely base decisions and/or plan maneuvers to avoid terrain, obstacles, or traffic. SVT oPERaTIoN activating and deactivating SVT: 1) Press the PFd opt Softkey. 2) Press the SVT Softkey. 3) Press the Terrain Softkey. The SVT display will cycle on or off with the Terrain Softkey. WaRNING: Do not use SVT runway depiction as the sole means for determining the proximity of the aircraft to the runway or for maintaining the proper approach path angle during landing. WaRNING: Intruder aircraft at or below 500 ft. AGL may not appear on the SVT display or may appear as a partial symbol. activating and deactivating Pathways: 1) Press the PFd opt Softkey. 2) Press the SVT Softkey. 3) Press the Pathways Softkey. The Pathway feature will cycle on or off with the Pathways Softkey. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 6 Flight Instruments EIS Nav/Com/ XPDR/Audio Flight Management Hazard Avoidance AFCS Additional Features Annun/Alerts Appendix Index Flight Instruments Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index activating and deactivating Horizon Headings: 1) Press the PFd opt Softkey. 2) Press the SVT Softkey. 3) Press the HdG LBL Softkey. The horizon heading display will cycle on or off with the HdG LBL Softkey. activating and deactivating airport Signs: 1) Press the PFd opt Softkey. 2) Press the SVT Softkey. 3) Press the aPT Sign Softkey. Display of airport signs will cycle on or off with the aPT Sign Softkey. FIELd oF VIEW Configuring field of view: 1) While viewing the ‘Map - Navigation Map’ Page, press the MENU Key to display the Page Menu. 2) Turn the large FMS Knob to highlight Map Settings and press the ENT Key. 3) Turn the FMS Knob to select the Map Group and press the ENT Key. 4) Turn the large FMS Knob to scroll through the Map Group options to Field of View. 5) Turn the small FMS Knob to select On or Off. 6) Push the FMS Knob to return to the ‘Map - Navigation Map’ Page. PFd aNNUNCIaTIoNS aNd aLERTING FUNCTIoNS Setting the Minimum altitude alert and bug: 1) Press the TMR/REF Softkey. 2) Turn the large FMS Knob to highlight the ‘Minimums’ Field. 3) Turn the small FMS Knob to select BARO, TEMP COMP, or RAD ALT. OFF is selected by default. Press the ENT Key or turn the large FMS Knob to highlight the ‘Next’ Field. 4) Use the small FMS Knob to enter the desired altitude (from zero to 16,000 feet). 5) If TEMP COMP was selected, press the ENT Key or turn the large FMS Knob to highlight the ‘Next’ Field and then enter the temperature (-59˚C to 59˚C) 6) To remove the window, press the CLR Key or the TMR/REF Softkey. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 7 Engine Indication System Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index ENGINE INdICaTIoN SySTEM (EIS) EIS dISPLay EIS display 7 6 8 1 2 3 4 5 9 Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 8 Engine Indication System Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 1 Engine Load Indicator Displays current engine loads as percentages 2 Tachometer Displays propeller speeds in revolutions per minute (rpm) 3 Fuel Flow Indicator Displays digital value of current fuel flow for each engine in gallons per hour (gph) 4 oil Temperature Indicator Displays engine oil temperature ranges; pointers labeled L and R indicate the oil temperature for each engine 5 oil Pressure Indicator Displays engine oil pressure ranges; pointers labeled L and R indicate the oil pressure for each engine 6 Coolant Temperature Indicator Displays coolant temperature ranges; pointers labeled L and R indicate coolant temperature for each engine 7 Fuel Temperature Indicator Displays fuel temperature range; pointers labeled L and R indicate the fuel temperature in each tank 8 Fuel Quantity Indicator Displays the fuel quantity in gallons (gal) of fuel in the tanks; pointers labeled L and R indicate the fuel quantity in each tank Indicator ranges from 0 to 25 gal per side with tick marks every 5 gal; the red range indicates 1 gal of unusable fuel 9 auxiliary Fuel (optional) Displays digital value of fuel quantity in gallons (gal) of fuel in the auxiliary tanks ENGINE PaGE The ‘EIS - Engine’ Page displays all engine, fuel, electrical, and fuel calculation information. To access this page, press the Engine Softkey or turn the large FMS Knob and select EIS. To return to the Engine Display from the Engine Page, press the Engine Softkey. Level 1 Level 2 description Engine Displays ‘EIS - Engine’ Page and second-level engine softkeys; press again to exit page dEC Fuel Decreases displayed fuel remaining in 1-gal increments INC Fuel Increases displayed fuel remaining in 1-gal increments RST Fuel Resets displayed fuel remaining to maximum fuel capacity for aircraft and fuel used to zero Engine Page Softkeys Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 9 Engine Indication System Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Engine Page 9 8 5 1 2 3 4 6 10 7 1 oil Temperature Indicator Displays engine oil temperature ranges in degrees Celsius (°C) 2 oil Pressure Indicator Displays engine oil pressure ranges in bar 3 Tachometer Displays propeller speeds in revolutions per minute (rpm) 4 Engine Load Indicator Displays current engine loads as percentages 5 Fluids Displays coolant temperature ranges Displays the temperature of each gearbox in degrees Celsius (°C) 6 deice (optional) Displays deice fluid in liters Displays in deice fluid time remaining (Endurance) in hours and minutes (HH:MM) for Norm and High settings 7 Electrical Displays the primary bus voltage for each side; pointers labeled L and R indicate the voltage for each side Displays each alternator load in amperes (amps); pointers labeled L and R indicate the amps for each side Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 10 Engine Indication System Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 8 Total Service Displays the aircraft’s total flight hours (hrs); activated when the aircraft becomes airborne 9 Fuel System Displays fuel quantity in the main tanks in gallons (gal) Displays fuel quantity in the auxiliary tanks (optional) in gallons (gal) Displays fuel temperature for each tank in degrees Celsius (°C); pointers labeled L and R indicate the fuel temperature in each tank Displays current fuel flow for each engine in gallons per hour (GPH) 10 Fuel Calculator Gallons Remain - Displays current fuel remaining (gal) as set by the pilot and adjusted for fuel burn since last set Gallons Used - Displays quantity of fuel used (gal) based on fuel flow since last reset Endurance - Displays flight time remaining in hours and minutes (HH:MM) based on the calculated fuel remaining Range NM - Displays aircraft range in nautical miles (nm) based on the calculated fuel remaining FUEL CaLCULaTIoNS adjusting the fuel totalizer quantity: On the Engine Page, use the dEC Fuel and INC Fuel Softkeys to obtain the desired fuel remaining (Gallons Used). Resetting the fuel totalizer: On the Engine Page, select the RST Fuel Softkey; this resets displayed fuel remaining (Gallons Remain) to the maximum fuel capacity for the aircraft and fuel used to zero. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 11 Nav/Com/XPdR/audio Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index aUdIo PaNEL aNd CNS CoM oPERaTIoN Manually tuning a CoM frequency: 1) Turn the CoM Knob to tune the desired frequency (large knob for MHz; small knob for kHz). 2) Press the Frequency Transfer Key to transfer the frequency to the active field. 3) Adjust the volume level with the COM VoL/SQ Knob. 4) Press the COM VoL/SQ Knob to turn automatic squelch on and off. auto-tuning a CoM frequency for a nearby airport from the PFd: 1) Press the Nearest Softkey on the PFD to open the ‘Nearest Airports’ Window. A list of 25 nearest airport identifiers and COM frequencies is displayed. 2) Turn the FMS Knob to scroll through the list and highlight the desired COM frequency. 3) Press the ENT Key to load the COM frequency into the COM Standby Frequency Field. 4) Press the Frequency Transfer Key to transfer the frequency to the COM Active Frequency Field. auto-tuning a CoM frequency from the WPT and NRST Pages: 1) From any page the COM frequency can be auto-tuned, activate the cursor by pressing the FMS Knob or pressing the appropriate softkey. 2) Turn the FMS Knob to place the cursor on the desired COM frequency. 3) Press the ENT Key to display the ‘Load Frequency’ Window. 4) Turn the FMS Knob to place the cursor on the desired COM frequency field. 5) Press the ENT Key to load the COM frequency into the selected COM frequency field. or: 1) Press the MENU Key to display the page menu. 2) Turn the large FMS Knob to scroll through the menu options. 3) Press the ENT Key to place the cursor on the desired selection. 4) Scroll through the frequency selections with the FMS Knob. 5) Press the ENT Key to display the ‘Load Frequency’ Window. 6) Turn the FMS Knob to place the cursor on the desired COM frequency field. 7) Press the ENT Key to load the COM frequency into the selected COM frequency field. Changing CoM frequency channel spacing: 1) From the ‘Aux – System Setup 1’ Page. 2) Press the FMS Knob to activate the flashing cursor. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 12 Nav/Com/XPdR/audio Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index 3) Turn the large FMS Knob to highlight the Channel Spacing Field in the COM Configuration Box. 4) Turn the small FMS Knob to select the desired channel spacing. 5) Press the ENT Key to complete the channel spacing selection. NaV oPERaTIoN NaV RadIo SELECTIoN aNd aCTIVaTIoN Manually tuning a NaV frequency: 1) Turn the NaV Knob to tune the desired frequency in the NAV Tuning Box. 2) Press the Frequency Transfer Key to transfer the frequency to the NAV Active Frequency Field. 3) Adjust the volume level with the NAV VoL/Id Knob. 4) Press the NAV VoL/Id Knob to turn the Morse code identifier audio on and off. auto-tuning a NaV frequency from the WPT and NRST Pages: 1) From any page the NAV frequency can be auto-tuned, activate the cursor by pressing the FMS Knob or the appropriate softkey. 2) Turn the FMS Knob to place the cursor on the desired NAV identifier or NAV frequency. 3) On the Nearest VOR and Nearest Airports pages, press the FREQ Softkey to place the cursor on the NAV frequency. 4) Press the ENT Key to display the ‘Load Frequency’ Window. 5) Turn the FMS Knob to place the cursor on the desired NAV frequency field. 6) Press the ENT Key to load the NAV frequency into the selected NAV frequency field. or: 1) When on the NRST pages, press the MENU Key on the PFD/MFD Controller to display the page menu. 2) Turn the large FMS Knob to scroll through the menu options. 3) Press the ENT Key to place the cursor in the desired window. 4) Scroll through the frequency selections with the FMS Knob. 5) Press the ENT Key to display the ‘Load Frequency’ Window. 6) Turn the FMS Knob to select the desired NAV frequency field. 7) Press the ENT Key to load the NAV frequency into the selected NAV frequency field. adF/dME TUNING Tuning an adF frequency: 1) Press the adF/dME Softkey to display the ‘ADF/DME Tuning’ Window. 2) Turn the large FMS Knob to place the selection cursor over the standby ADF frequency field. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 13 Nav/Com/XPdR/audio Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 3) Turn the small FMS Knob to begin data entry and change each digit. 4) Turn the large FMS Knob to move the cursor to the next digit position. 5) Press the ENT Key to complete data entry for the standby frequency. Transferring the active and standby adF frequencies: 1) Turn the large FMS Knob to place the selection cursor over the standby ADF frequency field. 2) Press the ENT Key to complete the frequency transfer. Selecting an adF receiver mode: 1) Turn the large FMS Knob to place the selection cursor over the ADF mode field. 2) Turn the small FMS Knob to select the desired ADF receiver mode. adjusting adF receiver volume: 1) Turn the large FMS Knob to place the selection cursor over the ADF volume field. 2) Turn the small FMS Knob to adjust volume as desired. Selecting dME transceiver pairing: 1) Press the adF/dME or dME Softkey to display the ‘ADF/DME Tuning’ Window. 2) Turn the small FMS Knob to select the DME tuning mode. 3) Press the ENT Key to complete the selection. ModE S TRaNSPoNdER Selecting a transponder mode: 1) Press the XPdR Softkey to display the Transponder Mode Selection Softkeys. 2) Press the desired softkey to activate the transponder mode. Entering a transponder code with softkeys: 1) Press the XPdR Softkey to display the Transponder Mode Selection Softkeys. 2) Press the Code Softkey to display the Transponder Code Selection Softkeys, for digit entry. 3) Press the digit softkeys to enter the code in the code field. When entering the code, the next softkey in sequence must be pressed within 10 seconds, or the entry is cancelled and restored to the previous code. Press the BKSP Softkey to move the code selection cursor to the previous digit. Five seconds after the fourth digit has been entered, the transponder code becomes active. Entering a transponder code with the PFd FMS Knob: 1) Press the XPdR and the Code Softkeys as in the previous procedure to enable code entry. 2) Turn the small FMS Knob on the PFD to enter the first two code digits. 3) Turn the large FMS Knob to move the cursor to the next code field. 4) Enter the last two code digits with the small FMS Knob. 5) Press the ENT Key to complete code digit entry. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 14 Nav/Com/XPdR/audio Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index FLIGHT Id REPoRTING Entering a Flight Id: 1) Press the TMR/REF Softkey to display the Timer/References Window. 2) Press the FMS Knob to activate the selection cursor, if not already activated. 3) Turn the large FMS Knob to scroll down to the Flight ID. 4) Turn the small FMS Knob to enter the desired Flight ID. 5) Press the ENT Key to complete Flight ID entry. addITIoNaL aUdIo PaNEL FUNCTIoNS INTERCoM Intercom ModES audio Panel Pilot Hears Copilot Hears Passenger Hears or or Selected Radios Aural Alerts Selected Radios Aural Alerts Passenger MIC Selected Radios Aural Alerts Selected Radios Aural Alerts Selected Radios Aural Alerts Passenger MIC Selected Radios Aural Alerts Copilot MIC Selected Radios Aural Alerts Pilot MIC Passenger MIC Selected Radios Aural Alerts Selectd Radios Aural Alerts Passenger MIC Selected Radios Aural Alerts Copilot MIC Passenger Mic Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 15 Nav/Com/XPdR/audio Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index audio Panel Pilot Hears Copilot Hears Passenger Hears Selected Radios Aural Alerts Passenger MIC Selected Radios Aural Alerts Selected Radios Aural Alerts Pilot MIC Passenger MIC Selected Radios Aural Alerts Copilot MIC Passenger MIC Selected Radios Aural Alerts Pilot MIC Passenger MIC Pilot MIC Copilot MIC Passenger MIC ICS Isolation Modes Intercom Volume and Squelch The VOL/CRSR Knob controls selection and volume or manual squelch adjustment for au- dio sources that may not be adjustable anywhere else in the system. The small knob controls the volume or squelch. Turning the large knob activates and/or moves the cursor (flashing white annunciator or flashing blue annunciator in Blue-Select Mode) to select the audio source to adjust. The cursor will time-out after a few seconds and the position of the cursor will al- ways default back to the PILOT ICS Key. Pressing the small knob cancels the cursor. BLUE-SELECT ModE (TELEPHoNE/ENTERTaINMENT dISTRIBUTIoN) The Blue-Select Mode is entered by pressing the small knob when the volume control cur- sor (flashing white annunciator) is not active. If the volume control cursor is active, press the small knob twice. The first press will cancel the volume control cursor, the second will activate Blue-Select Mode. The annunciator over the TEL Button will be flashing blue. Any combination of the annun- ciators over the PILOT ICS, COPLT ICS, and PASS ICS buttons may be blue. Select the de- sired button to turn the blue annunciator on or off to distribute the telephone audio to selected crew/passenger positions. Turn the large knob to select MUS1 or MUS2, and select the crew/ passenger positions to receive the music audio. Selecting any button other than PILOT ICS, COPLT ICS, PASS ICS, TEL, MUS1, or MUS2 will cancel Blue-Select Mode. Pressing the small knob will also cancel Blue-Select Mode. After approximately ten seconds with no input, the Blue-Select Mode will automatically cancel. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 16 Nav/Com/XPdR/audio Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index BLUETooTH NoTE: Pairing is only necessary during the first attempt to connect a Bluetooth device to the audio panel. Once paired, the audio panel and the device will connect automatically. Pairing a Bluetooth device with the audio Panel Press and hold the inner knob for two seconds. The Bluetooth Annunciator flashes to in- dicate the unit is discoverable and the aural message “Bluetooth discoverable” is heard. The audio panel will remain discoverable for 90 seconds or until a successful pair is established. Once paired, the Bluetooth Annunciator turns steady blue and the aural message “Bluetooth paired” is heard. assigning an audio Source to the Bluetooth device Press the TEL, MUS1, or MUS2 key until the annunciator turns blue (the audio from the Bluetooth source will not be heard until this step is complete). The key annunciator cycles OFF-WHITE-BLUE. WHITE selects the wired audio source. BLUE selects the Bluetooth audio source. The BLUE source assignment will persist through Bluetooth audio connection disrup- tions. NoTE: The Bluetooth audio can only be assigned to one source at a time. Once the Bluetooth audio is assigned to an audio source, the remaining entertainment audio sources will only cycle between OFF and WHITE. Bluetooth audio will maintain a separate volume level and Blue Select distribution from the wired audio source. If the Bluetooth connection is supporting a phone call, all intercom posi- tions listening to that source can also speak on the call through the headset MICs. additional Bluetooth Control Functions When the Audio Panel detects a recording device as the Bluetooth connected device, the Pilot ICS Annunciator will turn blue. All audio heard by the Pilot will be recorded. Press and hold the PILOT ICS Key to enable/disable Bluetooth recording mode. aUdIo PaNEL PREFLIGHT PRoCEdURE Manually adjusting the Squelch and Volume Settings: 1) Press the MaN SQ Key so the in-key annunciation is illuminated. 2) Verify manual squelch is set to full open. 3) To enable the intercom selection(s) press the PILoT ICS, CoPILoT ICS, and/or PaSS ICS Keys so the in-key annunciation(s) are illuminated. 4) Turn CRSR Control Knob to select the intercom audio source to be adjusted. Once selected, turn VoL/SQ Control Knob to set the intercom audio level for that position. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 17 Nav/Com/XPdR/audio Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 5) Turn CRSR Control Knob to select the COM/NAV radios and each remaining audio source to be adjusted. Once selected, turn VoL/SQ Control Knob to adjust the volume level for that position. 6) Press the MaN SQ Key so the in-key annunciation is no longer illuminated. Auto Squelch will now be active. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 18 Nav/Com/XPdR/audio Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/alerts appendix Index Blank Page Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 19 Flight Management Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index FLIGHT MaNaGEMENT NaVIGaTIoN STaTUS BoX aNd daTa BaR Changing a field in the MFd Navigation data Bar: 1) Select the ‘Aux - System Setup 1’ Page. 2) Press the FMS Knob momentarily to activate the flashing cursor. 3) Turn the large FMS Knob to highlight the desired field number in the ‘MFD Data Bar Fields’ Box. 4) Turn the small FMS Knob to display and scroll through the data options list to select the desired data. 5) Press the ENT Key. Pressing the defaults Softkey returns all fields to the default setting. USING MaP dISPLayS MaP oRIENTaTIoN Changing the Navigation Map orientation: 1) With the ‘Map - Navigation Map’ Page displayed, press the MENU Key. The cursor flashes on the ‘Map Settings’ option. 2) Press the ENT Key to display the ‘Map Settings’ Menu. 3) Select the ‘Map’ Group. 4) Press the ENT Key. 5) Turn the large FMS Knob, or press the ENT Key once, to select the ‘Orientation’ Field. 6) Turn the small FMS Knob to select the desired orientation. 7) Press the ENT Key to select the new orientation. 8) Press the FMS Knob to return to the base page. Enabling/disabling North Up above and selecting the minimum switching range: 1) Press the MENU Key with the ‘Map - Navigation Map’ Page displayed. The cursor flashes on the ‘Map Settings’ option. 2) Press the ENT Key. The ‘Map Settings’ Menu is displayed. 3) Select the ‘Map’ group. 4) Press the ENT Key. 5) Highlight the ‘North Up Above’ Field. 6) Select ‘On’ or ‘Off’ using the small FMS Knob. 7) Press the ENT Key to accept the selected option. The flashing cursor highlights the range field. 8) Use the small FMS Knob to select the desired range. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 20 Flight Management Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 9) Press the ENT Key to accept the selected option. 10) Press the FMS Knob to return to the ‘Map - Navigation Map’ Page. MaP RaNGE Configuring automatic zoom: 1) Press the MENU Key with the ‘Map - Navigation Map’ Page displayed. The cursor flashes on the ‘Map Settings’ option. 2) Press the ENT Key. The ‘Map Settings’ Menu is displayed. 3) Turn the small FMS Knob to select the ‘Map’ group. 4) Press the ENT Key. 5) Turn the large FMS Knob to highlight the ‘Auto Zoom’ On/Off Field, and select ‘Off’ or ‘On’ using the small FMS Knob. 6) Press the ENT Key to accept the selected option. The flashing cursor highlights the ‘Auto Zoom’ display selection Field. 7) Select ‘MFD’, ‘PFD’, or ‘All’ using the small FMS Knob. 8) Press the ENT Key to accept the selected option. The flashing cursor highlights the ‘Max Look FWD’ Field. Times are from zero to 999 minutes. 9) Use the FMS Knobs to set the time. Press the ENT Key. 10) Repeat step 9 for ‘Min Look FWD’ (zero to 99 minutes) and ‘Time Out’ (zero to 99 minutes). 11) Press the FMS Knob to return to the ‘Map - Navigation Map’ Page. MaP PaNNING Panning the map: 1) Push the Joystick to display the Map Pointer. 2) Move the Joystick to move the Map Pointer around the map. 3) Push the Joystick to remove the Map Pointer and recenter the map on the aircraft’s current position. Reviewing information for an airport, NaVaId, or user waypoint: 1) With the desired map page displayed on the MFD, push the Joystick to display the Map Pointer and place the Map Pointer on a waypoint. 2) Press the ENT Key to display the ‘WPT - <Waypoint> Information’ Page for the selected waypoint. 3) Press the Go Back Softkey, the CLR Key, or the ENT Key to return to the ‘Map - Navigation Map’ Page showing the selected waypoint. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 21 Flight Management Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Reviewing information for a special-use or controlled airspace: 1) With the desired map page displayed on the MFD, push the Joystick to display the Map Pointer and place the Map Pointer on an open area within the boundaries of an airspace. (As the Map Pointer crosses the airspace boundary, the boundary is highlighted and airspace information is shown.) 2) Press the ENT Key to display an options menu. 3) ‘Review Airspaces’ should already be highlighted, if not select it. Press the ENT Key to display the ‘Information’ Window for the selected airspace. 4) Press the FMS Knob, the CLR Key, or the ENT Key to exit the ‘Information’ Window. MEaSURING BEaRING aNd dISTaNCE Measuring bearing and distance between any two points: 1) Press the MENU Key (with the ‘Map - Navigation Map’ Page displayed). 2) Use the FMS Knob to highlight the ‘Measure Bearing/Distance’ Field. 3) Press the ENT Key. A Measure Pointer is displayed on the map at the aircraft’s present position. 4) Move the Joystick to place the reference pointer at the desired location. The bearing and distance are displayed at the top of the map. Elevation at the current pointer position is also displayed. Pressing the ENT Key changes the starting point for measuring. 5) To exit the Measure Bearing/Distance option, push the Joystick; or select ‘Stop Measuring’ from the ‘Page Menu’ Window and press the ENT Key. ToPoGRaPHy displaying/removing topographic data on all MFd pages displaying navigation maps: 1) Press the Map opt Softkey. 2) Press the TER Softkey until ‘Topo’ is shown on the softkey to display topographic data. 3) Press the TER Softkey until ‘Off’ is shown on the softkey to remove topographic data from the navigation map. When topographic data is removed from the page, all navigation data is presented on a black background. displaying/removing topographic data on the PFd Inset Map or the HSI Map: 1) Press the Map/HSI Softkey. 2) Press the TER Softkey until ‘Off’ is shown on the softkey to remove topographic data from the navigation map. When topographic data is removed from the page, all navigation data is presented on a black background. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 22 Flight Management Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index displaying/removing topographic data using the ‘Map - Navigation Map’ ‘Page Menu’ Window: 1) Press the MENU Key with the ‘Map - Navigation Map’ Page displayed. The cursor flashes on the ‘Map Settings’ option. 2) Press the ENT Key. The ‘Map Settings’ Menu is displayed. 3) Turn the small FMS Knob to select the ‘Map’ Group. 4) Press the ENT Key. 5) Turn the large FMS Knob to highlight the ‘Terrain Display’ ‘Off, Topo, REL’ field. 6) Turn the small FMS Knob to select ‘Topo’ or ‘Off’. 7) Press the FMS Knob to return to the ‘Map - Navigation Map’ Page. Selecting a topographical data range (Terrain display): 1) Press the MENU Key with the ‘Map - Navigation Map’ Page displayed. The cursor flashes on the ‘Map Settings’ option. 2) Press the ENT Key. The ‘Map Settings’ Menu is displayed. 3) Turn the small FMS Knob to select the ‘Map’ group. 4) Press the ENT Key. 5) Use the large FMS Knob to highlight the ‘Terrain Display’ range field. Ranges are from 1 nm to 1000 nm. 6) To change the Terrain Display range setting, turn the small FMS Knob to display the range list. 7) Select the desired range using the small FMS Knob. 8) Press the ENT Key. 9) Press the FMS Knob to return to the ‘Map - Navigation Map’ Page. displaying/removing the topographic scale (Topo Scale): 1) Press the MENU Key with the ‘Map - Navigation Map’ Page displayed. The cursor flashes on the ‘Map Settings’ option. 2) Press the ENT Key. The ‘Map Settings’ Menu is displayed. 3) Turn the small FMS Knob to select the ‘Map’ group and press the ENT Key. 4) Turn the large FMS Knob to highlight the ‘Topo Scale’ ‘On/Off’ field. 5) Turn the small FMS Knob to select ‘On’ or ‘Off’. 6) Press the FMS Knob to return to the ‘Map - Navigation Map’ Page. MaP SyMBoLS Symbol Setup Setting up the ‘Land’, ‘aviation’ or ‘airspace’ group items: 1) Press the MENU Key with the ‘Map - Navigation Map’ Page displayed. The cursor flashes on the ‘Map Settings’ option. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 23 Flight Management Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 2) Press the ENT Key. The ‘Map Settings’ Menu is displayed. 3) Turn the small FMS Knob to select the desired group. 4) Press the ENT Key. The cursor flashes on the first field. 5) Turn the large FMS Knob to select the desired option. 6) Turn the small FMS Knob to select the desired setting (e.g. On/Off or maximum range). 7) Press the ENT Key to accept the selected option and move the cursor to the next item. 8) Repeat steps 5-7 as necessary. 9) Press the FMS Knob to return to the ‘Map - Navigation Map’ Page. Map declutter decluttering the MFd navigation map: Press the detail Softkey with the ‘Map - Navigation Map’ Page displayed. The current declutter level is shown. With each softkey press, another level of map information is removed. or: 1) Press the MENU Key with the ‘Map - Navigation Map’ Page displayed. 2) Turn the FMS Knob to highlight ‘Declutter’. The current declutter level is shown. 3) Press the ENT Key to apply the next declutter level and return to the ‘Map - Navigation Map’ Page. decluttering the PFd Map: 1) Press the Map/HSI Softkey. 2) Press the detail Softkey. The current declutter level is shown. With each selection, another level of map information is removed. aIRWayS displaying/removing airways: 1) Press the Map opt Softkey. 2) Press the aWy Softkey. Both High and Low Altitude Airways are displayed (AWY On). 3) Press the softkey again to display Low Altitude Airways only (AWY LO). 4) Press the softkey again to display High Altitude Airways only (AWY HI). 5) Press the softkey again to remove High Altitude Airways. No airways are displayed (AWY Off). or: 1) Press the MENU Key with the ‘Map - Navigation Map’ Page displayed. The cursor flashes on the ‘Map Settings’ option. 2) Press the ENT Key. The ‘Map Settings’ Menu is displayed. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 24 Flight Management Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 3) Turn the small FMS Knob to select the ‘Airways’ Group, and press the ENT Key. 4) Turn the large FMS Knob to highlight the ‘Low ALT Airways’ On/Off field. 5) Turn the small FMS Knob to select ‘Off’ or ‘On’. 6) Press the FMS Knob to return to the ‘Map - Navigation Map’ Page. Selecting an airway range (Low aLT airways or High aLT airways): 1) Press the MENU Key with the ‘Map - Navigation Map’ Page displayed. The cursor flashes on the ‘Map Settings’ option. 2) Press the ENT Key. The ‘Map Settings’ Menu is displayed. 3) Turn the small FMS Knob to select the ‘Airways’ Group, and press the ENT Key. 4) Turn the large FMS Knob to highlight the ‘Low ALT Airways’ or ‘High ALT Airways’ range field. 5) To change the range setting, turn the small FMS Knob to display the range list. 6) Select the desired range using the small FMS Knob. 7) Press the ENT Key. 8) Press the FMS Knob to return to the ‘Map - Navigation Map’ Page. addITIoNaL NaVIGaTIoN MaP ITEMS Navigation maps can display some additional items. These items (e.g. track vector, selected altitude intercept arc, wind vector, fuel range ring, and SVT field of view) can be displayed/ removed individually. Setting up additional ‘Map’ Group items: 1) Press the MENU Key with the ‘Map - Navigation Map’ Page displayed. The cursor flashes on the ‘Map Settings’ option. 2) Press the ENT Key. The ‘Map Settings’ Menu is displayed. 3) Turn the small FMS Knob to select the ‘Map’ Group. 4) Press the ENT Key. The cursor flashes on the first field. 5) Turn the large FMS Knob to select the desired option. 6) Turn the small FMS Knob to select ‘On’ or ‘Off’. or: If it is a data field, use the FMS Knob to select the range or time value. 7) Press the ENT Key to accept the selected option and move the cursor to the next item. 8) Repeat steps 5-7 as necessary. 9) Press the FMS Knob to return to the Navigation Map. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 25 Flight Management Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index WayPoINTS aIRPoRTS Selecting an airport for review by identifier, facility name, or location: 1) From the ‘WPT - Airport Information’ Page (Info 1 Softkey), press the FMS Knob. 2) Use the FMS Knobs and enter an identifier, facility name, or location within the ‘Airport’ Box. 3) Press the ENT Key. 4) Press the FMS Knob to remove the cursor. Selecting a runway: 1) With the ‘WPT - Airport Information’ Page (Info 1 Softkey) displayed, press the FMS Knob to activate the cursor. 2) Turn the large FMS Knob to place the cursor in the ‘Runways’ Box, on the runway designator. 3) Turn the small FMS Knob to display the desired runway (if more than one) for the selected airport. 4) To remove the flashing cursor, press the FMS Knob. Viewing a destination airport: From the ‘WPT - Airport Information’ Page (Info 1 Softkey) press the MENU Key. Select ‘View Destination Airport’. The Destination Airport is displayed. Nearest airport Viewing information for a nearest airport on the PFd: 1) Press the Nearest Softkey to display the ‘Nearest Airports’ Window. Press the FMS Knob to activate the cursor. 2) Highlight the airport identifier with the FMS Knob and press the ENT Key to display the ‘Airport Information’ Window. 3) To return to the ‘Nearest Airports’ Window press the ENT Key (with the cursor on ‘Back’) or press the CLR Key. The cursor is now on the next airport in the nearest airports list. (Repeatedly pressing the ENT Key moves through the airport list, alternating between the ‘Nearest Airports’ Window and the ‘Airport Information’ Window). 4) Press the CLR Key or the Nearest Softkey to close the PFD ‘Nearest Airports’ Window. Viewing information for a nearest airport on the MFd: 1) Turn the large FMS Knob to select the ‘NRST’ Page Group. 2) Turn the small FMS Knob to select the ‘NRST - Nearest Airports’ Page (it is the first page of the group, so it may already be selected). If there are no Nearest Airports available, “None Within 200nm” is displayed. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 26 Flight Management Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index 3) Press the aPT Softkey; or press the FMS Knob; or press the MENU Key, highlight ‘Select Airport Window’ and press the ENT Key. The cursor is placed in the ‘Nearest Airports’ Box. The first airport in the nearest airports list is highlighted. 4) Turn the FMS Knob to highlight the desired airport. (Pressing the ENT Key also moves to the next airport.) 5) Press the FMS Knob to remove the flashing cursor. Viewing runway information for a specific airport: 1) With the ‘NRST - Nearest Airports’ Page displayed, press the RNWy Softkey; or press the MENU Key, highlight ‘Select Runway Window’; and press the ENT Key. The cursor is placed in the ‘Runways’ Box. 2) Turn the small FMS Knob to select the desired runway. 3) Press the FMS Knob to remove the flashing cursor. Selecting nearest airport surface and minimum runway length matching criteria: 1) Use the FMS Knob to select the ‘Aux - System Setup 1’ Page. 2) Press the FMS Knob momentarily to activate the flashing cursor. 3) Turn the large FMS Knob to highlight the ‘Runway Surface’ Field in the ‘Nearest Airport’ Box. 4) Turn the small FMS Knob to select the desired runway option (Any, Hard Only, Hard/ Soft, Water). 5) Press the ENT Key. The cursor moves to the ‘Minimum Length’ Field in the ‘Nearest Airport’ Box. 6) Use the FMS Knob to enter the minimum runway length (zero to 25,000 feet) and press the ENT Key. 7) Press the FMS Knob to remove the flashing cursor. NoN-aIRPoRT WayPoINTS Waypoint Information Viewing Non-airport Waypoints: 1) Turn the large FMS Knob to select the ‘WPT’ Page Group. 2) Turn the small FMS Knob to select the ‘WPT - Intersection, NDB, VOR, VRP, or User WPT Information’ Page. 3) Press the FMS Knob to display the flashing cursor in the ‘Intersection, NDB, VOR, VRP, or User Waypoint’ Box. 4) Use the FMS Knobs and enter an identifier, facility name, or location. 5) Press the ENT Key, if needed. 6) Press the FMS Knob to remove the flashing cursor. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 27 Flight Management Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Nearest Non-airport Waypoints Viewing Nearest Non-airport Waypoints: 1) Turn the large FMS Knob to select the ‘NRST’ Page Group. 2) Turn the small FMS Knob to select the ‘NRST - Nearest Intersections, NDB, VOR, VRP, or User WPTS’ Page. 3) Press the FMS Knob to display the flashing cursor in the ‘Nearest INT, NDB, VOR, VRP, or User’ Box, or: If the ‘NRST - Nearest VOR’ Page is displayed, to display the flashing cursor: Press the VoR Softkey. or: a) Press the MENU Key b) Highlight ‘Select VOR Window’, and press the ENT Key. 4) If needed, press the ENT Key or turn either FMS Knob as needed to select an identifier. 5) Press the FMS Knob to remove the flashing cursor. Creating User Waypoints Creating user waypoints from the ‘WPT - User WPT Information’ Page: 1) Press the New Softkey, or press the MENU Key and select ‘Create New User Waypoint’. 2) Enter a user waypoint name (up to six characters). 3) Press the ENT Key. The current aircraft position is the default location of the new waypoint. 4) If desired, define the type and location of the waypoint in one of the following ways: Select “RAD/RAD” using the small FMS Knob, press the ENT Key, and enter the two reference waypoint identifiers and radials into the ‘Reference Waypoints’ Window using the FMS Knobs. or: Select “RAD/DIS” using the small FMS Knob, press the ENT Key, and enter the reference waypoint identifier, the radial, and the distance into the ‘Reference Waypoints’ Window using the FMS Knobs. or: Select “LAT/LON” using the small FMS Knob, press the ENT Key, and enter the latitude and longitude into the ‘Information’ Window using the FMS Knobs. 5) Press the ENT Key to accept the new waypoint. 6) If desired, change the storage method of the waypoint to temporary by moving the cursor to “Temporary” and pressing the ENT Key to check or uncheck the box. 7) Press the FMS Knob to remove the flashing cursor. Garmin G1000 NXi Cockpit Reference Guide for the da62 190-02622-00 Rev. A 28 Flight Management Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features annun/alerts appendix Index Flight Instruments EIS Nav/Com/ XPdR/audio Flight Management Hazard avoidance aFCS additional Features abnormal operation annun/ alerts appendix Index Creating user waypoints from map pages: 1) Push the Joystick to activate the panning function and pan to the map location of the desired user waypoint. 2) Press the ENT Key. The ‘WPT - User WPT Information’ Page is displayed with the capture d position. 3) Enter a user waypoint name (up to six characters). 4) Press the ENT Key to accept the selected name. 5) If desired, define the type and location of the waypoint in one of the following ways: Select “RAD/RAD” using the small FMS Knob, press the ENT Key, and enter the two reference waypoint identifiers and radials into the ‘Reference Waypoints’ Window using the FMS Knobs. or: Select “RAD/DIS” using the small FMS Knob, press the ENT Key, and enter the reference waypoint identifier, the radial, and the distance into the ‘Reference Waypoints’ Window using the FMS Knobs. or: Select “LAT/LON” using the small FMS Knob, press the ENT Key, and enter the latitude and longitude into the ‘Information’ Window using the FMS Knobs. 6) Press the ENT Key to accept the new waypoint. 7) If desired, change the storage method of the waypoint to temporary or normal by moving the cursor to “Temporary” and pressing the ENT Key to check or uncheck the box. 8) Press the FMS Knob to remove the flashing cursor. 9) Press the Go Back Softkey to return to the map page. Editing User Waypoints Editing a user waypoint comment or location: 1) With the ‘WPT - User WPT Information’ Page displayed, press the FMS Knob to activate the cursor. The cursor is placed in the ‘User Waypoint’ Box. 2) Use the FMS Knobs to enter the name of the User Waypoint; or turn the large FMS Knob and scroll to the desired waypoint in the ‘Use