Airworthiness Directive AD/BEECH 35/67 Amdt 6

Full document text

COMMONWEALTH OF AUSTRALIA Civil Aviation Safety Regulations 1998 CIVIL AVIATION SAFETY AUTHORITY Regulation 39.001 Page 1 of 3 AIRWORTHINESS DIRECTIVE On the commencement date specified below, and for the reasons set out in the background section, the CASA delegate whose signature appears below repeals Airworthiness Directive (AD) AD/BEECH 35/67 Amdt 5 and issues the following AD under subregulation 39.001 (1) of CASR and subsection 33 (3) of the Acts Interpretation Act 1901. The AD requires that the action set out in the requirement section (being action that the delegate considers necessary to correct an unsafe condition) be taken in relation to the aircraft or aeronautical product mentioned in the applicability section: (a) in the circumstances mentioned in the requirement section; and (b) in accordance with the instructions set out in the requirement section; and (c) at the time mentioned in the compliance section. Textron Aviation (Beechcraft) 35 (Bonanza) Series Aeroplanes AD/BEECH 35/67 Amdt 6 Wing Bolt, Nut and Fitting 12/2025 Applicability: All models of Textron Aviation (formerly Beechcraft) 35 series aeroplanes, all serial numbers Requirement: 1. Remove inspection covers from wing attach fitting recesses and inspect for corrosion or loss of inhibitor. Also inspect drain holes for any blockage that would cause water or debris to accumulate. Note 1: It may be necessary to use a bright light and mirror/magnifying glass to see hard to view areas of the bolt or fittings for signs of corrosion on accessible areas of the bolt. Non accessible areas like the bolt thread encapsulated by the nut will be inhibited, so it is highly unlikely they will experience corrosion unless the general surrounding area is corroded. 2. Remove and inspect wing bolts, washers, nuts and fittings in accordance with Beechcraft Maintenance Manual 36-590001-9 Revision D2 May 29, 2024 Chapter 57, as in force on the date of commencement of this AD. Note 2: The bolt torque should be checked before removal for inspection or replacement to confirm the bolt has been torqued to correct value. If the torque value is incorrect, other maintenance action may be required. Note 3: Amendment 5 of this AD referred, and this Amendment also refers, to all serial numbers within its Applicability as the type certificate holder has not updated the Beechcraft Shop manual which includes other serial number ranges. The maintenance listed above at Requirement 2 is to be utilised for all serial numbers with reference to the wing bolt, nut and fitting requirements. 3. Retire wing bolts, washers and nuts from service and replace with new hardware in accordance Beechcraft Maintenance Manual 36-590001-9 Revision D2 Chapter 57, as in force on the date of commencement of this AD. Render unserviceable all hardware retired. Alternatively, as per the above aircraft maintenance manual the bolts may be maintained on condition IAW Table 201 Beechcraft Maintenance Manual 36-590001-9D Revision D2 May 29, 2024, Chapter 57, as in force on the date of commencement of this AD. Compliance: For Requirement 1: Every 12 calendar months for all aircraft. If visible corrosion is found within the recess or on visible portion of the bolt or nuts, washers or fittings, then Requirement 2 must be accomplished before further flight. COMMONWEALTH OF AUSTRALIA Civil Aviation Safety Regulations 1998 CIVIL AVIATION SAFETY AUTHORITY Regulation 39.001 Textron Aviation (Beechcraft) 35 (Bonanza) Series Aeroplanes AD/BEECH 35/67 Amdt 6 (continued) Page 2 of 3 For Requirement 2: a. For aircraft operating only in private operations: i. unless the inspection has already been accomplished in accordance with the Beechcraft Bonanza Shop Manual 35-590096 Revision B22 dated April 1, 2011 or the Beechcraft Maintenance Manual 36-590001-9D Revision D2 Revision Date May 29, 2024, each as in force on the date of commencement of this AD (the requirement documents) within 10 years from the initial installation of the wing bolts — inspect within 100 hours’ time in service (TIS) or 12 months from the commencement date of this AD, whichever occurs first. Note 4: Installation of the wing bolts includes where they are removed for inspection purposes and re-installed. ii. re-inspect at intervals not to exceed 10 years from the previous inspection. b. For all other operational categories: i. unless the inspection has already been accomplished in accordance with either of the requirement documents within 5 years from the installation of the wing bolts — inspect within 100 hours’ TIS or 12 months from the commencement date of this AD, whichever occurs first. Note 5: Installation of the wing bolts includes where they are removed for inspection purposes and re-installed. ii. re-inspect at intervals not to exceed 5 years from the previous inspection. For Requirement 3: Before 20 years TIS after the first installation of new zero time wing bolts. Alternatively, as per the maintenance manual the bolts may be maintained on condition IAW table 201 of the Beechcraft Maintenance Manual 36-590001-9D Revision D2 May 29, 2024, Chapter 57, as in force on the date of commencement of this AD. Note 6: Always replace wing attach nuts with new items when removing the wing attach bolts for inspection. Mandatory reporting requirements: Both NIL findings of defects and confirmed defects for Requirement 2 inspection must be reported via CASA’s Defect Reporting Service, either through the online portal at: https://www.casa.gov.au/resources-and-education/our-systems/defect-report-service or by using Form 404 available from: https://www.casa.gov.au/defect-report Commencement date: This AD commences on 13 July 2025. COMMONWEALTH OF AUSTRALIA Civil Aviation Safety Regulations 1998 CIVIL AVIATION SAFETY AUTHORITY Regulation 39.001 Textron Aviation (Beechcraft) 35 (Bonanza) Series Aeroplanes AD/BEECH 35/67 Amdt 6 (continued) Page 3 of 3