Alumigrip 10P8-11 Technical Data Sheet

Full document text

Page 1 of 6 AkzoNobel Aerospace Coatings 1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905 Mail: aerospace@akzonobel.com / Online: aerospace.akzonobel.com AkzoNobel Aerospace Coatings Alumigrip 10P8-11 Technical Data Sheet Product Group Epoxy primer Characteristics A two component, VOC compliant epoxy primer designed to provide a very smooth finish optimizing the appearance of the subsequent topcoat. Alumigrip 10P8-11 utilizes exempt solvents in meeting the required VOC level. Product Information Components Base material Curing Solution 10P8-11 EC-286 Specifications Cessna Textron Aviation US Military CMFS035. CSFS084 TM 3405 MIL-PRF-23377 Type I, Class C2 Qualified Product List Product specifications are constantly changing, to ensure the most accurate information regarding specifications, please check our online qualified product list (QPL) at aerospace.akzonobel.com/products. Surface Conditions - Surface pretreatment is an essential part of the painting process. - Apply over similar MIL-C-5541 pre-treated aluminum substrates or as a reactivation primer over previously primed, painted and sanded paint systems. May also be applied over Metaflex SP 1050. Cleaning Page 2 of 6 AkzoNobel Aerospace Coatings 1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905 Mail: aerospace@akzonobel.com / Online: aerospace.akzonobel.com Alumigrip 10P8-11 Epoxy Primer AkzoNobel Aerospace Coatings Instruction for Use Mixing Ratio (volume) 10P8-11 EC-286 1 part 1 part - Stir or Shake until all pigment is uniformly dispersed before adding curing solution. - Stir the catalyzed mixture thoroughly. Induction Time Not Applicable. Note For use with plural component equipment. Product can also be sprayed with conventional spray equipment with pressure pot or siphon cup. Initial Spraying Viscosity (23ºC/73ºF) 32-45 seconds ISO-Cup 4 17-23 seconds Zahn- Signature Cup #2 Note Viscosity measurements are provided as guidelines only and are not to be used as quality control parameters. Certified information is provided by certification documentation available on request. Pot life (23ºC/73ºF) 4 hours Dry Film Thickness (DFT) 15-23 μm 0.6-0.9 mils Page 3 of 6 AkzoNobel Aerospace Coatings 1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905 Mail: aerospace@akzonobel.com / Online: aerospace.akzonobel.com Alumigrip 10P8-11 Epoxy Primer AkzoNobel Aerospace Coatings Application Recommendations Conditions Temperature: Relative Humidity: 15-35°C 59-95°F 35-75% Note Alumigrip 10P8-11 may be applied in conditions outside the limits shown above. Care must be exercised to ensure a satisfactory result. Please contact your local AkzoNobel Aerospace Coatings representative to determine the appropriate application techniques when environmental conditions fall outside of the recommended range. . Equipment Spray gun type Nozzle orifice Product flow Dynamic air pressure at gun- inlet* Conventional Gravity Feed: 1.2mm-1.4mm Pressure Feed: 1.2mm-1.4 mm 350-475ml/min Use enough Air Pressure. </=100psi or (7 bar) HVLP/ next generation Gravity Feed: 1.2mm-1.4mm, Pressure Feed: 1.2mm -1.5mm 240ml -350ml/min maximize and ensure uniform fan pattern, not to exceed regulatory guideline for air pressure at the cap. Page 4 of 6 AkzoNobel Aerospace Coatings 1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905 Mail: aerospace@akzonobel.com / Online: aerospace.akzonobel.com Alumigrip 10P8-11 Epoxy Primer AkzoNobel Aerospace Coatings Air spray electrostatic 1.2mm & 1.5mm 1.2mm tip: fluid flow 230-240 ml/min 1.5mm tip-fluid flow rate up to 300- 360 ml/min 58-65 psi / 4-4.5 bar High pressure Air Assisted electrostatic angle 0.09 – 0.13 inch/60º 260 – 300ml/min Fluid pressure: 75-90 psi / bar 0.9- 1.3 psi Air pressure at gun inlet: 58-65 psi / 4-4.5 bar Number of Coats Apply 1 full wet coat to reach required film thickness. Cleaning of Equipment Use MEK, MPK or similar. Physical Properties Drying Times (23ºC/73ºF) Dry to topcoat Full cure Ambient cure 2 hours 7 days air dry Ambient cure Set to touch in 30 minutes (77°F/25°C @ 50% RH) - Accelerated cure, option 1: Accelerated cure flashing 20 minutes at RT followed by 6 minutes at 180°-220°F / 82°- 105°C will result in a dry-to-handle, dry-to topcoat, or dry- to-stack condition. Page 5 of 6 AkzoNobel Aerospace Coatings 1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905 Mail: aerospace@akzonobel.com / Online: aerospace.akzonobel.com Alumigrip 10P8-11 Epoxy Primer AkzoNobel Aerospace Coatings - Accelerated cure, option 2: Accelerated cure flashing 20 minutes at RT followed by 30 minutes at 120°F/49°C will result in a dry-to-handle, dry-to topcoat, or dry-to-stack condition. Theoretical Coverage 21.5 m² per liter ready to apply at 15 μm dry film thickness. 876 ft² per US gallon ready to apply at 0.6 mil dry film thickness. Dry Film Weight 1.66 g/m²/μm 0.00862 lbs/ft²/mil Volatile Organic Compounds 825 g/L / 6.88 lbs/gal 340 g/L / 2.84 lbs/gal - excluding exempt solvents acc. to US EPA Gloss (60º) <6 GU Color Reddish Green Flash-point 10P8-11 EC-286 TR-114 27°C / 81°F 43°C / 109°F -17°C / 1.4°F Storage Store the product dry and at a temperature between 5 and 38ºC / 41 and 100ºF per AkzoNobel Aerospace Coatings specification. Store in the original unopened containers. Storage temperature may vary per OEM specification requirements. Refer to container label for specific storage life information. Page 6 of 6 AkzoNobel Aerospace Coatings 1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200,