GPS 100 Aviation Kit Installation Manual

blade antenna installation. Recommended installation locations for the Low Profile Antenna are the same. Av. Kit Install. Manual 190-00004-00 Rev. G Page 7 2.1.2 NOISE SOURCES The antenna should be located at least 3 ft from transmitting antennas such as VHF Comm, HF transmitter, DME, Transponder, and Radar. Cabling for the GPS 100 should not be routed near components or cabling which are sources of electrical noise. 2.1.3 ELECTRICAL BONDING No special precautions need to be taken to provide a bonding path between the antenna and the aircraft structure. 2.1.4 ANTENNA LIMITATIONS The GPS 100 Blade and Low Profile Antennas are recommended for installations where the airspeed of the aircraft will be subsonic. For aerodynamic considerations, the Low Profile Antenna is recommended for operation above 200 kts. 2.2 RACK CONSIDERATIONS 2.2.1 ACCESSIBILITY Plan a location which gives the pilot complete and comfortable access to the entire keypad and which is plainly visible from the pilotís perspective. Check that there is adequate depth for the rack in the instrument panel. A location away from heating vents or other sources of heat generation is optimal. Figure 2-2 illustrates a typical aviation rack installation. 2.3 CABLING AND WIRING Use only the antenna cable supplied in the installation kit. Other cabling may lead to degraded performance. Check that there is ample space for the cabling and mating connectors. Avoid sharp bends in cabling and routing near aircraft control cables. 2.4 ANNUNCIATORS If the installation includes any electrical interface with other flight instruments, an annunciator may be required. Refer to current FAA directives. Av. Kit Install. Manual 190-00004-00 Rev. G Page 8 SECTION 3 INSTALLATION PROCEDURE 3.1 INSTALLATION KIT CONTENTS One of the following two installation kits is required for aircraft installation, depending on the type of antenna used. The GPS 100 Aviation Installation Kit (010-10002-00) consists of the following parts: P/N DESCRIPTION QTY 011-00013-00 BLADE ANTENNA SUBASSEMBLY 1 011-00014-00 RACK SUBASSEMBLY 1 115-00015-00 BACKING PLATE 1 117-00001-00 EJECTOR PIN 4 161-00024-00 PLACARD, INSTRUMENT PANEL 1 190-00004-00 INSTALLATION MANUAL (THIS MANUAL) 1 211-20001-00 #8-32 SS, PH, FLAT HEAD SCREW 4 253-00002-00 ANTENNA GASKET 1 320-00003-00 CABLE ASSY, COAX 1 330-00017-00 CONNECTOR, BNC, MALE, CLAMP 1 330-00024-00 CONNECTOR, 15 PIN DSUB, FEMALE 1 The GPS 100 Low Profile Aviation Installation Kit (010-10008-00) consists of the following parts: P/N DESCRIPTION QTY 011-00042-00 LOW PROFILE ANTENNA SUBASSEMBLY 1 011-00014-00 RACK SUBASSEMBLY 1 115-00031-00 BACKING PLATE 1 117-00001-00 EJECTOR PIN 4 161-00024-00 PLACARD, INSTRUMENT PANEL 1 190-00004-00 INSTALLATION MANUAL (THIS MANUAL) 1 210-10004-09 NUT, SELF-LOCKING, #8-32 4 253-00002-00 ANTENNA GASKET 1 320-00003-00 CABLE ASSY, COAX 1 330-00017-00 CONNECTOR, BNC, MALE, CLAMP 1 330-00024-00 CONNECTOR, 15 PIN DSUB, FEMALE 1 The following equipment is required for installation but is not included in the installation kit: #6-32 Flat Head Screw (4 ea.) #6-32 Self-locking Nut (4 ea.) Av. Kit Install. Manual 190-00004-00 Rev. G Page 9 3.2 ANTENNA INSTALLATION The Blade Antenna outline and footprint dimensions are shown in Figure 3-1. The Low Profile Antenna outline and footprint dimensions are shown in Figure 3-1A. Both antennas require the same Installation procedure. A. Using the backing plate as a template, mark the location of the mounting holes and the through hole for coax cable. Drill or punch the holes. B. The antenna installation must provide adequate support for the antenna consid- ering a maximum drag load of 14 lbs (at subsonic speed). Install a doubler plate to reinforce thin skinned aircraft. Observe guidelines for acceptable installation practices as outlined in AC 43.13-2A. C. Seal the antenna and gasket to the fuselage using a good quality electrical grade sealant. Use caution to insure that the antenna connector is not contaminated with sealant. Insure that the mounting screws are fully tightened and that the antenna base is well seated against the gasket. CAUTION: Do not use construction grade RTV sealant or sealants containing acetic acid. These sealants may damage the electrical connections to the antenna. Use of these type sealants may void the antenna warranty. 3.3 CABLE INSTALLATION A. Route the coax cable supplied to the rack location keeping in mind the recommen- dations of Section 2. Secure the cable in accordance with good aviation practice. B. Trim the supplied RG-59/U cable to the desired length and install the BNC connector (330-00017-00) per the cabling instructions on Figure 3-2. 3.4 RACK INSTALLATION A. Figure 3-3 shows outline dimensions for the aviation rack. Install the rack in a rectangular 6.320" x 2.000" hole in the instrument panel. Exercise caution when installing the rack into the instrument panel. The rack is designed to facilitate removal of the GPS 100 for portable use. Deformation of the rack may make it difficult to install and remove the GPS 100. B. Install the rack in the aircraft panel using four #6-32 countersunk screws and four self-locking nuts. The screws are inserted from the inside through the holes in the sides of the rack (see Figure 3-4). Av. Kit Install. Manual 190-00004-00 Rev. G Page 10 3.5 AVIATION INTERFACE SET-UP Before installing the GPS 100 into the aviation rack, several operating parameters need to be set-up so that the GPS 100 can interface properly with the aviation rack and other avionics. Press the ON button. The Initialization page will appear. See Chapter 3 in the GPS 100 Ownerís Manual for information on initialization. Approve the initialization page. There are several set-up pages which can be viewed by pressing the SET key. Press the SET key until the CDI SETTINGS page is displayed. Move the cursor to highlight the setting for STEER TO. Press the clear key until ìD-BARî appears. Move the cursor to highlight the ìOKî and press ENT. Press the SET key to continue through the set- up pages and set-up the following parameters: STEER TO> D-BAR OUTPUT> AVIATION Ensure that the following parameters are set-up properly for your application. The following are typical settings for an aviation environment. See Chapter 10 in the GPS 100 Ownerís Manual for more information on customizing the GPS 100 settings: CDI SCALE>+ 5.00 >AUTO MAG NAV> nm kt ALT> ft FPM DATUM> WGS 84 or as indicated on navigation charts for the area. 3.6 GPS 100 INSTALLATION To install or remove the GPS 100 from the aviation rack, see the addendum to the GPS 100 Ownerís Manual included in the installation kit. This addendum should be given to the end user. 3.7 PLACARD After completing the installation, a placard stating ìGPS limited to VFR use onlyî must be installed on the panel in clear view of the pilot. The placard may be Garmin p/n 161-00024-00 as supplied with the installation kit, or a suitable equivalent. SECTION 4 CHECKOUT PROCEDURE In order to verify the installation, the aircraft must be outside the hanger and well away from any buildings or aircraft that might block satellite signals. To perform the checkout procedure it is necessary to be familiar with operating the GPS 100 or to have the GPS 100 Ownerís Manual available for reference. Av. Kit Install. Manual 190-00004-00 Rev. G Page 11 With power applied to the aviation rack turn the GPS 100 on. The Self-Test Page will be displayed followed by the Initialization Page. The GPS 100 must be properly set- up per the instructions in Section 3.5 before performing the checkout procedure. Prior to approving the Initialization page verify the following interfaces as appropriate: CDI Ensure the CDI is deflected half scale left (2.5 dots). TO/FROM Ensure the TO/FROM flag is in a TO condition. NAV FLAG Ensure the NAV FLAG is out of view. MESSAGE ANNUNCIATOR Ensure the message annunciators are illuminated. RMI Ensure the RMI indicates 315o. Approve the Initialization page, select the GPS Status page from Navigation Menu 1 (see Chapter 9 for more information on the GPS Status page). The process of satellite acquisition is fully automatic and under normal circumstances will require 2-3 minutes to obtain navigation information (15 minutes or less when searching the sky). If unable to acquire satellites, relocate the aircraft away from obstructions which might be shading reception. If the situation does not improve, check the antenna installation. AUDIO Select the Event Timer 1 page from Navigation Menu 2 (see Chapter 10 of the GPS 100 Ownerís Manual for more information on event timers). Set the count down timer to go off in 1 minute. Prior to viewing the message indicating ìTIMER 1 EXPIREDî (while the "M" character is flashing in the upper right hand corner of the display), ensure the audio interface is operating properly. ARGUS 3000/5000/7000 or STORMSCOPE SERIES II with NAVAID or SHADIN FUEL MANAGEMENT SYSTEM Once GPS position information is available, use the AutoStoreTM function to store a waypoint at your current position (see Chapter 8 of the GPS 100 Ownerís Manual for information on the AutoStoreTM function). After storing your location, GOTO the stored waypoint (see Chapter 6 of the GPS 100 Ownerís Manual for information on the GOTO function). Ensure the ARGUS or STORMSCOPE or SHADIN fuel management system are receiving data from the GPS 100 and are functioning properly. Av. Kit Install. Manual 190-00004-00 Rev. G Page 12 FIGURE 1-1 AV. RACK PINOUT DEFINITION Av. Kit Install. Manual 190-00004-00 Rev. G Page 13 FIGURE 1-2 INTERCONNECT SCHEMATIC Av. Kit Install. Manual 190-00004-00 Rev. G Page 14 f:\antplace.cdr Antenna must be on top of aircraft. Antenna masked by vertical fin, T tail, or dorsal fin OK FIG 2-1 ANTENNA INSTALLATION CONSIDERATIONS Maintain 6"(16 cm) compass safe distance Unit to be mounted in aircraft radio rack as high as possible. If the loca- tion chosen is very low, or to the left of the pilot, it should be evaluated for display visibility. FIG 2-2 GPS INSTALLATION CONSIDERATIONS Av. Kit Install. Manual 190-00004-00 Rev. G Page 15 FIGURE 3-1 BLADE ANTENNA INSTALLATION Av. Kit Install. Manual 190-00004-00 Rev. G Page 16 FIGURE 3-1A LOW PROFILE ANTENNA INSTALLATION Av. Kit Install. Manual 190-00004-00 Rev. G Page 17 FIGURE 3-2 COAX CABLE INSTALLATION Av. Kit Install. Manual 190-00004-00 Rev. G Page 18 FIGURE 3-3 AVIATION RACK DIMENSIONS Av. Kit Install. Manual 190-00004-00 Rev. G Page 19 FIGURE 3-4 AVIATION RACK INSTALLATION Av. Kit Install. Manual 190-00004-00 Rev. G Page 20 This page was intentionally left blank. Av. Kit Install. Manual 190-00004-00 Rev. G Page 21 APPENDIX A INSTALLATION DETAILS FOR BEECH B60 1.0 INTRODUCTION: This appendix provides airframe specific information which is necessary to install the GARMIN GPS 100 navigation system in the Beech Duke Model B60 in accordance with STC (tbd). When so installed, the GPS 100 system is approved for use as a supplementary navigation system under Visual Flight Rules (VFR) only. A functional block diagram of the system is shown in Figure A-1. The information provided herein is to be considered supplemental to the information contained in the GARMIN GPS 100 Aviation Kit Installation Manual, P/N 190-00004- 00. Within this appendix, the base document will be referred to as the "Installation Manual". 2.0 INSTALLATION INSTRUCTIONS 2.1 ANTENNA The GPS 100 antenna is to be installed on top of the cabin on the aircraft centerline at fuselage station 138.0. Figure A-2 illustrates the proper antenna positioning. Refer to section 2.1 of the Installation Manual for general antenna mounting requirements. 2.2 AVIATION RACK INSTALLATION The GPS 100 aviation rack is to be installed on the right side of the instrument panel radio rack as shown in figure A-3. The controls and display of the GPS 100 must be readily visible to the pilot when seated at the controls. To install the aviation rack, position it in the instrument panel in the desired position, assuring that the front is not twisted out of square. Match drill the flanges on the radio rack to the installation holes on the GPS 100 aviation rack. Using 4 each #6-32 screws and self locking nuts, attach the aviation rack to the aircraft panel. For additional information, refer to the Installation Manual. 2.3 WIRING Fabricate an appropriate cable to connect the GPS 100 aviation rack to 28VDC power, a message annunciator, a remote switch (for selecting between GPS and standard navigation equipment), a transfer switch with integral white, illuminated annuncia- tors with black markings (to control and indicate the status of the remote switch). Wiring connections are to be made in accordance with Figure A-4. Breaker locations are to be as shown in Figure A-5. Route and connect the wiring in accordance with Advisory Circular AC-43.13-2A. After the wiring installation is complete, carefully check the operation of all flight controls throughout their range to assure that no operational interference exists. Av. Kit Install. Manual 190-00004-00 Rev. G Page 22 2.4 PLACARDS After completion of the GPS 100 system installation, affix a durable placard on the instrument panel in the location shown in Figure A-3 which states ìGPS limited to VFR use only". GARMIN placard p/n 161-00024-00 or an appropriate equivalent should be used for this purpose. 3.0 OPERATIONAL CHECKOUT When the installation is complete, conduct a post installation checkout as specified in section 4 of the Installation Manual, being sure to check the proper operation of all connected instruments. 4.0 RETURN TO SERVICE After installation, a new weight and balance must be computed to show the GPS 100 components. The aircraft should then be returned to service by completion of FAA form 337 by an appropriately certificated person. Av. Kit Install. Manual 190-00004-00 Rev. G Page 23 FIG A-1 FUNCTIONAL BLOCK DIAGRAM Av. Kit Install. Manual 190-00004-00 Rev. G Page 24 FIG A-2 FUSELAGE STATIONS AND WEIGHT AND BALANCE DATA Av. Kit Install. Manual 190-00004-00 Rev. G Page 25 FIG A-3 PANEL LAYOUT Av. Kit Install. Manual 190-00004-00 Rev. G Page 26 FIG A-4 WIRING DIAGRAM Av. Kit Install. Manual 190-00004-00 Rev. G Page 27 FIG A-5 BREAKER LOCATIONS