Product Information Sheet

HDMI cable or the metal of a light bulb and socket, you could use the standard spray (Part No. G5S-6 or D5S-6). Just hold the end away from any equipment and spray one short burst on metal area, and your done (the solvent will evaporate and leave a thin layer. B) If you want to apply DeoxIT® to specific metal connections and connectors on sensitive circuit boards (one where you are not positive if any product should be applied to questionable components on the board). In this case you want to select an applicator that will allow for precision application on DeoxIT®. Selecting one will depend on the type of connection/connector. For example; an edge connector on the circuit board would be best applied with the Cotton Wipes (Part Nos. G50W, D50W and S50W). With a socket, the best appli- cator maybe one of the pens (Part Nos. G100P, D100P and S100P). Page 3 CAIG Laboratories, Inc. 12200 Thatcher Court, Poway, CA 92064 U.S.A. P: 858/486-8388 | E: info@caig.com WEB: www.caig.com | www.deoxit.com Marine Avionics Communications Photography Security Medical Energy Audio/Video Computers Automotive Electrical APPLICATOR Method: Select one of our existing applicators (pen, wipes, oilers, brush, etc.) and apply directly to the needed metal part. Remember to apply only small amounts and wipe off excess if required. SELECTING Sprays and Liquids: SELECTING a DeoxIT® SPRAY: (See Chart on last page: “DeoxIT® - Spray Selection Guide - Figure 1) A) Standard Spray: Provides flushing action Products: DeoxIT® D5 D-Series Spray (D5S-6) DeoxIT® Gold G-Series G5 Spray (G5S-6) DeoxIT® Shield S-Series S5 Spray (S5S-6) Formulation: 5% DeoxIT® (active ingredient), 75% odorless mineral spirits (carrier solvent), 20% propel- lant. Formulation contains petroleum naphtha (odorless mineral spirits) solvent, and is briefly flammable (until solvent evaporates within 2-3 minutes). It’s slower to evaporate, providing flushing action to remove surfac- es dirt, grease and other contaminants. Is ideal for connectors and components removed from equipment or those that are easily accessible. It is safe on plastics. When in doubt, always test for compatibility, especially vintage equipment with aging ABS plastic(s). B) NEW, Non drip - Quick Dry Spray: Nonflammable, fast evaporating carrier solvent formula Products: DeoxIT® DN5 D-Series Spray (DN5S-6N) DeoxIT® DN5 D-Series Mini-Spray (DN5S-2N) DeoxIT® Gold G-Series GN5 Spray (GN5S-6N) DeoxIT® Gold G-Series GN5 Mini-Spray (GN5S-2N) DeoxIT® Gold G-Series GX5 Spray (GX5S-6N) DeoxIT® Shield S-Series SN5 Spray (SN5S-6N) DeoxIT® Shield S-Series SN5 Mini-Spray (SN5S-2N) Formulation: 5% DeoxIT® (active ingredient), 75% SOLSTICE® PF, 20% TRANS-1,3,3,3-TETRAFLUO- RO-PROP-1-ENE. May be used where fast evaporation and/or non-flam- mability is required, and no dripping is preferred. It is also safe on plastics. C) 100% Spray: No solvents, metered one-shot valve Products: DeoxIT® D100 D-Series Spray (D100S-2) DeoxIT® Gold G100 G-Series Spray (G100S-2) Formulation: 20% DeoxIT® (active ingredient), 80% propellant Used where maximum lubrication is needed, but solvents are not desired. For example, where cleaning and lubrication is required or over-spray might adverse- ly affect sensitive plastics. DeoxIT® utilizes a metered valve which sprays short bursts of 100% liquid. SELECTING a DeoxIT® 100% LIQUID: Applicators: a) Squeeze Tube: Used by OEMs for maintenance kits. Provides small drop to surface. b) Pen - felt tip: Precision application, slight abrasive action. Provides liquid through felt tips. Replacement tips available. Page 4 CAIG Laboratories, Inc. 12200 Thatcher Court, Poway, CA 92064 U.S.A. P: 858/486-8388 | E: info@caig.com WEB: www.caig.com | www.deoxit.com Marine Avionics Communications Photography Security Medical Energy Audio/Video Computers Automotive Electrical c) Oiler Pen: Very precise application of fluid. Provides pin-point application of liquid. Ideal for hard to reach applications. d) Oiler Squeeze Bottle: Similar to Oiler Pen, except in squeeze bottle. e) Wipes: Individual packaged wipes (thin paper material). For connections easily accessible and surfaces, i.e. audio/video connections, batteries, etc. f) Wipes: Jar with 50 wipes (thick cotton material). For connections easily accessible accessible and smooth and irregular surfaces, i.e. edge connectors, industrial connections. g) Brush: Small 7.4 mL bottle with brush applicator. General purpose for applying liquid with a nylon brush. Ideal for applying to outer and inner surface with wiping action. Care should be taken to keep brush clean. h) Bulk Bottles: For production applications. Contact CAIG for information. Which DeoxIT® 5% LIQUID Applicator do I Use? Using the 5% concentrate applies the correct amount of DeoxIT® to the metal surface. Usually used for production applications. Can be swabbed, dipped or sprayed onto the surface. Available in several size containers. a) Oiler Squeeze Bottle: Similar to Oiler Pen, except in squeeze bottle. b) Bulk Bottles: For production applications. Contact CAIG for additional information. 3. HOW, for Large Scale & Production Application. There are many ways to apply DeoxIT® in large scale applications. You can use any number of our applicators (spray, pens, wipes, brushes, etc.). You need to decide which applicator should be used to provide a best coverage, with the least waste and least amount of labor. Below are just a few examples. (Contact us if you have a specific requirement and we will help you select the best method). BATH Method: If you have many sockets, connectors or metal parts that are going to be installed into equipment, you can place the parts into a bath or ultrasonic cleaner with our 5% solution of DeoxIT® (Part Nos. D5L, G5L and S5L). Page 5 CAIG Laboratories, Inc. 12200 Thatcher Court, Poway, CA 92064 U.S.A. P: 858/486-8388 | E: info@caig.com WEB: www.caig.com | www.deoxit.com Marine Avionics Communications Photography Security Medical Energy Audio/Video Computers Automotive Electrical SPRAY Method: This can be accomplished in several ways. If the circuit board or device has been checked for compatibility you can incorporate it into your existing production line and use a cleaning section (with 5% solution) to apply the DeoxIT® to the parts. If applying DeoxIT® cannot be applied by this type of automation, you can use one of our standard spray cans (Part Nos. D5S-6, DN5S-6N, G5S-6, GN5S-6N, S5S-6, SN5S-6N). Use a masking template to section off areas of the board that you do not need DeoxIT® and then spray. 4. IMPORTANT NOTES. Just always keep in mind, only a small amount of DeoxIT® should to be applied to the metal surface. More is NOT better. You do not need to make sure DeoxIT® gets onto the entire metal surface. If you missed a little, DeoxIT® will migrate and coat the metal surfaces that were not treated. Also, even if you were only able to treat the connector and not the socket, DeoxIT®, once part is connected, will migrate over to the socket and treat the exposed metal. This is one of the best attributes of DeoxIT®. Becomes very important on moving connections or ones subject to vibration. 5. TESTING FOR COMPATIBILITY. We always recommend testing for compatibility on parts and equipment that you do not have previous knowledge or experience. For material compatibility, refer to individual DATA Sheets (see link in next section). Compatibility testing can usually be done by applying DeoxIT® to one of the parts or areas, then allowing the DeoxIT® to remain on the surface for a few days or up to a week. If no deformation, change in the visual appear- ance and electrical/mechanical performance is deter- mined, then compatibility should be OK. Obviously, additional testing should be done for production and very critical applications. LINKS for Additional Information: 1. Bulletin CEG-2014 “NEW CAIG Essentials Guide - Brief Description of the Entire CAIG Product Line, 2018” Link: goo.gl/YGY1Nu 2. Bulletin C-WD18 “Why DeoxIT® Products are Different?” “Which Product Do I Use?” Link: goo.gl/3ATWNg 3. Product Information Link: http://caig.com/product-literature/ Information includes; Sales information and descriptions for many CAIG products. 4. Technical Information Link: http://caig.com/technical-information/ Information includes; Technical information for many CAIG products, including; When and How to use, Tech Sheets, Specs, Reference to old products, Shelf Life, NSN numbers, Tests, etc.. 5. Product DATA Sheets Link: http://caig.com/product-data-sheets/ Information includes; Features/benefits, formulation, direction for use for applicator, product selection guide, spray selection guide, plastics compatibility, shipping information, etc. 6. MSDS Sheets (Material Safety Data Sheets) Link: http://caig.com/material-safety-data-sheets/ 7. DeoxIT® Specs, Compatibility and Technical Information. Link: http://caig.com/technical-information/ (Select #5 on page) DeoxIT® D-Series, DeoxIT® Gold (G-Series, Gx Series, Gx2 and Gx3), DeoxIT® Shield and DeoxIT® Grease (formerly CaiLube Grease). CAIG Laboratories, Inc. 12200 Thatcher Court, Poway, CA 92064 U.S.A. P: 858/486-8388 | E: info@caig.com WEB: www.caig.com | www.deoxit.com Marine Avionics Communications Photography Security Medical Energy Audio/Video Computers Automotive Electrical Page 6 Specifications include; Temperature ranges, material compatibility, flow points, viscosities, specific gravity, conductivity, dielectric strength, specific insulation resistance and more. 8. DeoxIT® Specifications & Comparisons to Other Products. Link: http://caig.com/technical-information/ (Select #6 on page) Information includes; DeoxIT® specifications, technical and comparisons to Polyphenyl Ether (OS-138), Stabilant 22, Silicone - based lubricants, Mineral oil - based lubricants, WD-40. MANUFACTURER DISCLAIMER: To the best of our knowledge, the information contained herein is accurate. However, neither CAIG Laboratories, Inc., or any of its subsidiaries assumes any liability whatsoever for the accuracy or completeness of the information contained herein. All materials may present unknown hazards and should be used with caution. In particular, improper use of our products and their inappropriate combination with other products and substances may produce harmful results which cannot be anticipated. Final determination of the suitability of any material is the sole responsibility of the user. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that may exist. All service performed on internal parts and equipment should be provided by qualifed technicians. Product Information Sheet SB-DFU18, 1/2018 FIGURE 1. Feedback and Suggestions: If you have additional information you would like to see in this bulletin, please submit it at: http://store.caig.com/s.nl/it.I/id.7/.f DeoxIT7 - Spray Selection Guide FP = Flushing properties QD = Quick dry / non drip NF = Nonflammable PC = Plastics compatibility VOC = VOC (%) Product Series FP QD NF PC VOC Standard - 5% solution   75% (588g/L) D5S-6, G5S-6, S5S-6, F5S-H6 N Series - 5% solution    0.0% DN5S-6N, DN5S-2N, GN5S-6N, GN5S-2N, SN5S-6N, SN5S-2N, FN5S-2N X Series - 5% solution    0.0% GX5S-6N 100% Spray solution   0.0% D100S-2, G100S-2, F100S-L2 DeoxIT7 Gold G-Series DeoxIT7 D-Series DeoxIT7 Gold GxL Gx-Series DeoxIT7 Gold Gx2 Gx2-Series DeoxIT7 Shield S-Series DeoxIT7 Fader F-Series DeoxIT7 - Product Selection Guide New Surfaces      * In Service / Used   Gold surfaces    Oxidation / corrosion visible  Conductive plastics  ** Outdoor / Severe environments   Deoxidizing / cleaning properties 20% 0.1% 0.1% 0.0% 0.0% 0.0% Metal / Plastic surfaces Yes Yes Yes Yes Yes Plastics compatibility Excellent Excellent Excellent Excellent Excellent Excellent Temperature range ( O C) -34/200 -45/240 -45/310 -45/500 -34/210 -26/150 Stationary & moving surfaces Yes Yes Yes Yes Yes Yes Seals & protects surface metals Good Excellent Excellent Excellent Good No Seals & protects base metals Fair Excellent Excellent Excellent Fair No  All products are Nonflammable and RoHs Compliant * In Service: Clean with DeoxIT7 D-Series. For added protection, follow with DeoxIT7 Gold (indoors), DeoxIT7 Shield (outdoors) or DeoxIT7 Grease (additional barrier).