AC 91-67 - Federal Aviation Administration

g. Deactivation means to make a piece of equipment or an instrument unusableto the pilot/crew by preventing its operation. “s h. Deferred Maintenance is the postponementof the repair or replacementof an item of equipment or an instrument. i. Equipment List is an inventory of equipment installed by the manufacturer or operator on a particular aircraft. j. Flight Operations Evaluation Board (FOEB). The FOEB is composed of FAA personnel who are operations, avionics, airworthiness, and aircraft certification specialists. The FOEB develops an MMEL for a particular aircraft type under the direction of the AEG. k. Inoperative means, that a system and/or component has malfunctioned to the extent that it does not accomplish its intended purpose and/or is not consistently functioning normally within its approvedoperatinglimits or tolerances. *. 1. Kinds of Operations List (KOL). The KOL specifies the kinds of operations (e.g., visual flight rules (VFR), instrument flight rules (IFR), day, or night) in which the aircraft can be operated. The KOL also indicates the installed equipment that may affect any operating limitation. Although the certification rules require this information, there is no standard format; consequently, the manufacturer may furnish it in various ways. . m. Letter of Authorization (LOA). The FSDO issues an LOA to the operator when the FSDO authorizesthe operator to operate under the provisions of an MEL. Together, the LOA, the procedures document (paragraph v. follow!ng), and the MMEL constitute a Supplemental Type Certificate (STC). The operator must carry the STC in the aircraft during its operation. n. Maintenance is the inspection, overhaul, repair, preservation, or replacement of parts. This definition excludes preventive maintenance(seeparagraphu. following). After a mechanic performs maintenance, other than preventive maintenance, a properly certificated maintenancepersonmust approvethe aircraft for * return to service. o. MMEL. An MMEL contains a list of items of equipmentand instrumentsthat may be inoperative on a specific type of aircraft (e.g., BE-200, Beechcraft model 200). It is also the basis for the development of an individual operator’sh4EL. .’ Par6 ...ul AC 91-67 6/28/H p. MEL. The MEL is the specific inoperative equipment documentfor a particular make and model aircraft by serial and registration numbers; e.g., BE-200, N12345. A FAR Part 91 MEL consists of the MMEL for a particular type aircraft, the MMEL’s preamble, the proceduresdocument,and a LOA. The FAA considers the MEL as an SC. As such, the MEL permits operation of the aircraft under specified conditions with certain equipment inoperative. q. Next Required Inspection is the one required under either an FAA-approved inspec- tion program, a lOO-hour inspection, or an annual inspection, as appropriate. r. Operations(0) and Maintenance (M) procedures in the MMEL refer to the specific maintenance procedures the operator uses to disable or render items of equipmentinoperative and to specific operating conditions and limita- tions, as appropriate. (1) An 0 symbol in column 4 of the MMEL indicates that a specific operations proceduremust be accomplishedbefore or during operation with the listed item of equipment inoperative. Nomally, the flightcrew accomplishesthese procedures;however, other personnel,such as maintenancepersonnel,may be qualified and authorized to perform the procedure. (2) An M symbol in column 4 of the MMEL indicates that a specific maintenance procedure must be accomplished before beginning operation with the listed item of equipment inoperative. Normally, maintenance personnelaccomplishtheseprocedures;however, other personnel,such as the flightcrew, may be qualified and authorized to perform certain functions. Qualified maintenancepersonnelmust perform procedures requiring specialized knowledge, skills, or the use of tools or test equipment. s. Operator refers to an individual or company (corporation, entiv, etc.). As used in this AC, operator applies to those who are applicantsfor, or holdersof, authority to conduct operationsunder the provisions of a-FAR Part 91 MEL. t. Placard is a decal or label with letters at least l/&inch high. The operator or mechanic must place the placard on or near inoperativeequipment or instrumentsso that it is visible to the pilot or flightcrew and alerts them to the inoperative equipment. u. Preventive Maintenance. The term preventivemaintenancerefersto simple or minor preservationoperationsand/orthe replacementof small standard parts not involving complex assembly. FAR Part 43, Appendix A(c), contains a list of preventive maintenanceitems. Qualified mechanics or certificated pilots may accomplishpreventive maintenanceand approve the aircraft for return to service. v. Procedures Document as referred to in this AC pertains to a separate document containing the 0 and M proceduresdevelopedby the operatorand any other operatinginformation applicableto operation with an MEL, such asthe “as requiredby the FAR” items that list the FAR by part and section or stipulate the operating conditions. w. Proposed Master Minimum Equipment List (PMMEL). The PMMEL is the working document used as the basis for development of the MMEL. Normally, the manufacturerproposesit during the certification process. However, an operator of a unique type aircraft, for which an MMEL doesnot exist, may submit a PMMEL for FAA approval. iv Par 6 - AC 9% 67 x. Return to Service, Return to service has two applications. An appropriately certificated personapprovesan aircraft for return to service after an inspection or after maintenance.A certificatedpilot, in fact, returns the aircraft to service after the pilot conductsan appropriatepreflight and acceptsthe aircraft for an intendedflight. y. Small Aircrap means aircraft with a maximum certificated takeoff weight of 12,500 pounds or less. z. STC. An STC is a major changein type design not great enough to require a new application for a type certificate under FAR 6 21.19. An example would be installation of a powerplant different from what was included in the original type certificate. aa. ripe Certfjicate Data- Sheets (TCDS) and Specificationsare documentsissued Acting Director, Flight tandards Service id by the FAA which describes the aircraft’s airworthinessrequirementsrelating to a specific type, make, and model of aircraft. These documentsare available at a FSDO. 7. COMMENTS INVITED. Comments regardingthis publication should be directed to: FederalAviation Administration Field pn>gramsDivision, AFS-500 Advisory Circular Staff P.O. Box 20034, Gateway Building Dubs International Airport Washington,DC 20041-2034 Every comment will not necessarily generatea direct acknowledgement to the commenter. Comments received will be considered in the development of upcoming revisions to AC’s or other related technical material. Par 6 . v (and &) 6128191 AC H-67 CONTENTS No. Page CHAPTER 1. GENERAL . . . . . . . . . . . . . c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. Applicability . . . . :. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 . MELVS.FAR§91.213(d) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 . RelationshipBetweenthePMMEL,theMMEL,andtheMEL . . . . . . . . . . . . . . . . . . 2 4 . Single- and Multiengine MEL’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5 l AircraftForWhichNoMMELHasBeenDeveloped . . . . . . . . . . . . . . . . . . . . l . . 3 6 . MELRestrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 . Removal or Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 8. InoperativeEquipment and RequiredInspections . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 1. Sample MaintenanceRecordEntries . . . . . . . . . . . . . . . . . . . . . . . 5 (and 6) 9..12. Reserved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 (and 6) CHAPTER 2. CONDUCTING OPERATIONS WITHOUT AN MEL ................... 7 13. Applying FAR 0 91.213(d) .......................................... 7 14. The Decision Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 2. Pilot Decision SequenceWhen OperatingWithout an MEL ............. 8 15:18 Reserved .................................................. 9 (and 10) J c CHAPTER 3. OPERATING AIRCRAFT WITH AN MEL . . . . . . . . . . . . . . . . . . . . . . . . . 11 19. Applicability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . 11 20 . Applying For MEL Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 21. ~LAufhOfization.;............................................. 13 22 . Revisio~..............................................~....~.~ 13 23. Conducting OperationsWith an MEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure 3. Pilot Decision SequenceWhen OperatingWith an MEL . . . . . . . . . . . . . . 16 Figure 4. Sample Aircraft Equipment DiscrepancyRecord . . . . . . . . . . . . . . . . . . . . 18 t , APPENDIX 1. Sample MMEL Documents (6 pages) . . . . . . . . . . . . . . . . . . . . . l . l l . . . . . l l 1 APPENDIX 2. Sample Letter of Authorization (2 pages) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 APPENDIX 3. Sample Title Page (1 page) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l . . . . . . . 1 APPENDIX 4. Commonly Asked QuestionsAbout MEL’s (3 pages) . . . . . . . . . . . . . . . . . . . . . 1 * . vii 6/28/91 AC 91-67 CHAPTER 1. GENERAL . ” 1. APPLICABILITY. This AC provides guidance for the operation of the following aircraft under FAR Part 91: authorization to operate with a FAR Part 91 MEL. a. Aircraft for which no MMEL has been developedby the FOEB: (1) Rotorcraft. (2) Nonturbine-poweredairplanes. (3) Gliders. (4) Lighter-than-air aircraft. 2. MEL VS. FAR 6 91.213(d). Although FAA amended FAR Part 91 to provide relief to operatorsunder the IMEL concept, some opera- tors may find it less burdensome or less complicated to operate under the provisions of FAR 5 91.213(d). The applicant should discuss the requirements of each method with FSDO inspectorsto decidewhich method of compliance better suits the particular operation. Appendix 3 contains a list of commonly asked questions which may assistin the decision. b. Aircraft fot which an M”EL has been deveZopedbut for which the FSDO has not authorizedoperation with an MEL. (1) Small rotorcraft. (2) Nonturbine-poweredsmall single and multiengine airplanes. a. An MEL is a precise listing of instruments, equipment, and procedures that allows an aircraft to be operatedunder specific conditibns with inoperative equipment. The MMEL, as part of the MEL, by nature does not cover equipment installed or modified under other STC’s. Any STC or other major modification may make the MMEL invalid for a particular modified aircraft. c. All other aitctaft which havean MEL or for which an operator seeks MEL authorizationunder FAR 6 91.213. d. An operator may operate an aircraft for which FAA has issued an original Experimental airworthiness certificate in accordance with FAR 0 91.213 only when authorized in that certificate’s operating limitations. e. This AC does not apply to operators holding certificates issuedunder FAR Parts 121, 125, 129, and 135. b. The FAR requite that all equipment installed on an aircraft in compliance with the airworthiness standards and operating rules be operative. The FAA-approved h4MEL includes thoseitems of equipment and other items which the FAA finds may be inoperative and yet maintain an acceptable level of safety. Obviously, the MMEL doesnot contain required items such as wings, flaps, rudders,etc. When a FAR Part 91 operator uses an MMEL as an MEL, all instrumentsand equipmentnot covered in the MMEL must be operative at all times regardlessof the operation conducted,unless: ji Holdets of letters of full deviation (1) They are newly installed and are authotity from FAR Part 125 and operating not instruments or equipment specifically under FAR Part 91, SubpartF, may apply for required by the airworthiness rule under which Chap, 1 Par 1 1 AC 91-67 6/28/91 the aircraftis type certificated,requiredby AD, or requiredfor specificoperationsunderFAR 8 91.213(b)(1)-(3),such as Traffic Alert and CollisionAvoidanceSystem(TCAS), an extra pieceof navigationalequipment,a windshear detectiondevice,a groundproximity warning system,a radaraltimeter,passenger convenience items,etc.; (2) The operator has developed proceduresfor disabling or renderingthem inoperative;and (3) The operatorhas contactedthe FSDOhavingoversightwithin 10calendardays following an installationandrequestedthat the equipmentbe addedto the MMEL. (i) TheoperatormustAmishthe followinginformation: (A) A copy of the STC or FAA Form 337, Major Repairand Alteration, thatapprovedeachequipment installationandthe associatedlimitations listed in the AFh4 supplement or onthe 337. TheFOEBneedsthis informationto accountfor installationdifferences as well as for maintainingMMEL relief that is consistentwith thelimitations. (B) A systemdescription that detailssufficientlytheinterfaceof the equipment with thecrew;i.e.,location,controls,operations, how it is used,etc. (C) A statement that describesthe transfer of function when the equipmentis inoperative;i.e., not requiredfor the flight, as per crew procedures,becauseof alternatesystems,etc. (ii) If the FAA determinesthat theequipmenthasbeenpreviouslyconsidered by the FOEB for inclusionin the MMEL and denied,or if the FOEB convenesand denies inclusion,the FAA will not grant relief. The equipmentmust be operationalbefore aircraft cantakeoff. (iii) If theFOEBdetermines that the equipmentshouldbe addedto the MMEL, theoperatorwill receivetheupdatedMMEL and mustprepare0 andM procedures for fhatpiece of equipment. c. If FAA has not authorized operating with an MEL for an operator’sspecificaircraft, the operatormay applyfor anMEL (Chapter3, paragraph m However, the operator can alwayselectto operatewithout an MEL under the provisionsof FAR 6 91.213(d). (1) FAR 5 91.213(d)requiresonly thoseinstruments listedin FAR 5 91.213(d)(2)to beoperative. (2) The operator can operatethe aircraftwiththoseinstrumentsandequipment not listedin FAR 6 91.213(d)(2)inoperative. 3. RELATIONSHIP BETWEEN THE PMMEL, THE MMEL, AND THE MEL. Whenanaircraftis first manufactured, theFOEB determinesthe minimumoperativeinstruments and equipmentrequiredfor safe flight in that aircraft type in each authorized operating environment. During the type certification process,the manufactul’er submitsa PMMELto the FOEB. Basedon its determinations,the FOEB reviewsthe PMMEL and developsan h4MELfrom it. Oncethe FOEBapprovesthe MMEL, a copyis availableto eachFSDOvia an automatedsystem that allows the FSDO to chap1 2 Par2 6/ 2$/91 AC 91-67 download the MMEL onto a diskette or hard COPY* The FSDO provides MMEL’s to applicants to use, along with the procedures document, preamble,and LOA, as an MEL. a. As technology changes and new equipment becomes available, the FOEB will reconveneto developnew MMEL’s or to revise and update existing ones. b. When an FOEB makes a change to an MMEL, all operatorsusing that MMEL as their h4EL will receive a postcard advising them of the revised MMEL. The FSDO provides operators copies of the revised MMEL. The operatorthen makesthe necessarychangesto the proceduresdocumentthrough thenormal revision process(Chapter3, paragraph22). , 4. SINGLE AND MULTIENGINE MEL’S, The FAA has developedMMEL’s for most of the FAA type certificated aircraft in general servicetoday. ‘All multiengine airplaneshave an MMEL that is specific to the type design; e.g., Beech Baron, BE-58. The FAA has developed a generic, single-engine MMEL to provide to operatorsof single-engineaircraft. 5. AIRCRAFT FOR WHICH NO MMEL HAS BEEN DEVELOPED. a. If an FOEB has not developed an hJMEL for a certain type of rotorcraft, nonturbinepowered airplane, glider, or lighter- than-air aircraft, that aircraft may he operated with inoperative equipmentunder the provisions of FAR 0 91.213(d). b. In those cases where an operator has an older or rare design aircraft that has no MMEL, the operator may submit a PMMEL to the appropriateFOEB for evaluation. Oncethe AEG approvesthe MMEL, the operatorcould useit as the MEL along with the other required documents. 6. MEL RESTRICTIONS. Operatorsof small rotor-craft,nonturbinepoweredsmall single- and multiengine airplanes, and other aircraft for which a MMEL has been developed,may elect to operatewith a MEL or under the provisions of FAR 0 91.213(d). However, the latter option does not apply if the aircraft has an MEL approved under FAR Parts 121, 125, 129, ‘or 135. For example, an owner has leased an aircraft to an air carrier operator, and the air carrier operator has applied for and received an approved MEL for FAR Part 135 operations. Compliance with such an MEL is mandatory, even during -FAR Part 91 operations. If the operator wants to operate under FAR 5 91.213(d), the operator would have to surrenderthe MEL authorization. 7. REMOVAL OR DEACTIVATION. When an operator elects to operate without an MEL, any inoperative instrument or equipment must either be removed (FAR 6 9 1.213(d)(3)(i)) or deactivated (FAR 8 91.213(d)(3)(ii)), then placarded. a. Removal of any item of equipment that affects the airworthiness of an aircraft requires following an approved procedure. A properly certificated maintenancepersonmust record the removal in accordancewith FAR 6 43.9. A person authorizedby FAR 6 43.7 must make the appropriateadjustmentsto the aircraft’s weight and balance information and the equipment list, fil’out and submit FAA Form 337, and,approve the aircraft for return to service. 6. The operator must evaluateany proposed deactivation to assurethere is no adverseeffect that could render another system less than fully capableof its intended function. Chap 1 Par3 3 AC 91-67 6/28/91 (1) A certificatedpilot can accomplish deactivation involvingroutinepilottasks,suchas turning off a system. However,for a pilot to deactivatean item or system,that task must come under the definition of preventive maintenance in FAR Part43, SubpartA. (2) If the deactivationprocedures do not fall underpreventivemaintenance, a properly certificatedmaintenance personmustaccomplish the deactivation.Themaintenance personmust recordthe deactivationin accordance with FAR 3 43.9 (figure 1, SampleMaintenance Record Entries.). c. Pkzcarding can be as simple as writing the word %operativet’ on a pieceof masking tapeandattachingit to theinoperative equipment or to its cockpitcontrol. Placardingis essential sinceit remindsthe pilot that the equipmentis inoperative. It also ensures that future flightcrewsandmaintenance personnel areaware of the discrepancy. 8. INOPERATIVE EQUIPMENT AND REQUIRED INSPECTIONS. Anoperatormay defermaintenance on inoperative equipmentthat hasbeendeactivated or removedandplacarded inoperative. a. When the aircrafl is due for inspection in accordance with the FAR, the operator shouldhave all inoperativeitems repairedor replaced. b. If an owner does not want spec@c inop- erative equipment repaired, then the mainte- nancepersonmust checkeachitem to seeif it conforms to the requirements of FAR 5 91.213(d). The operatorand maintenance personnelshould also assesshow permanent removalof the item couldaffect safeoperation of the aircra& (1) Therepairintervalcategories(A, B, C, D, etc.) in the MMEL do not applyto FAR Part91 MEL’S. (2) Themaintenance personmustfurnish the owner/operator with a signedanddatedlist of all discrepancies not repaired. (3) Themaintenance personmustensure thateachitemof inoperativeequipmentthatis to remaininoperativeis placardedappropriately. 4 chap 1 Par7 - 6128191 Placard(Minimum 1/8=inchhighletters) AC 91-67 LandingLight Inoperative: PREVENTIVE MAINTENANCE ENTRY: (DATE)Totaltime hours. Landinglight bulb removed in accordance with (manufacturer) maintenance manual, Chapter- Page_l. Landinglight switchplacarded inoperative. Pilot’sSignature CertificateNumber Placard(Minimum 1/84nchhighletters) Aircraft HeaterInoperative: MAINTENANCE ENTRY (FAR 9433): (DATE)Total time hours. Aircraft heaterandcontrol switchdeactivated by cappingheaterfuel linesin accordance with (manufacturer) maintenance manual,Chapter t Pa@-* Heatercontrolswitchplacardedinoperative. Mechanic’sSignature CertificateNumber Figure 1. Sample Maintenance Record Entries 9.42. RESERVED. Chap 1 5 (and 6) ‘. 6/28/91 AC 91-67 CHAPTER 2. CONDUCTING OPERATIONS WITHOUT AN MEL 13 APPLYING FAR § 91.213(d). This chipter providesguidancefor operatomwho elect to conductflight operationsunder the provisionsof FAR 0 91.213(d).Operatingunder FAR 8 91.213(d)requiresno applicationto or approval from. FAA. An operator, after operatingunderFAR 8 91.213(d),may electat any time to applyfor authorizationto operate underanMEAL(Chapter3). . 4 14 THE DECISIONSEQUENCE.Figure2 is a flow chartdepictingthe typicalsequence of eventsa pilot or operator,operatingunderFAR 9 91.213(d),shouldfollow when the pilot or operatordiscovelsinoperativeequipment.For example,during a preflight inspectionfor a VFR-day,cross-country flight, thepilotdiscovers that the number2 automaticdirectionfinder (ADF) headis inoperative. a. The pilot checks the uitctaft’s equip- ment tist ot KOL to seeif the number2 ADF is a requireditem (FAR 6 91.213(d)(2)(ii)).If the number2 ADF is requiredin the equipmentlist or KOL, the aircraft is not airworthy. The operatormusthavethenumber2 ADF replaced or repairedbeforeoperatingthe aircraft. In this example,the number2 ADF is not a required item on the equipmentlist. b. Nexh the pilot checks the uitwottht ness regulation underwhichthe aircraftwascer- tificatedto determineif the number2 ADF is part of the VFRday type certificate (FAR 5 91.213(d)(2)(i)). (These requirementsare summarizedin a TCDS, copiesof which are available at FSDO’s or from qualified maintenance personnel.)If thenumber2 ADF is required as part of the VFRday type certification,the aircraftis not airworthy. The operatormusthavethe number2 ADF replaced or repairedbeforeoperatingthe aircraft. In this example,the number2 ADF is not requi=dby typecertification. c. Net, the pilot checks to seeif an AD requites fhe number 2 ADF. The pilot can accomplishthis by checking the aircraft’s maintenance logs to seeif the number2 ADF wasinstalledasa resultof anAD. However,it may be necessaryfor the pilot to consulta qualifiedmaintenance personto determineAD compliance.If an AD requiresthe number2 ADF to be operative,the aircraftis not airwor- thy. Theoperatormusthavethenumber2 ADF replaced or rep&redbeforeoperatingthe aircraft. In this example,there is no AD requiringthe number2 ADF to be operative. d. Next, the pilot checks to see if the l number 2 ADF is requited by FAR $4’91.215, 91.205,ot 91207. Thepilotcanaccomplish this by checkingthosesectionsof the FAR or by consultingwith a maintenancetechnicianor FSDOpersonnel.If anyof thosesectionsof the FAR requirea number2 ADF, thenthe aircraft wouldnot be airworthywith thenumber2 ADF inoperative. The operator must have the number2 ADF replacedor repairedbefore operatingthe aircraft. In this example,those sectionsof theFAR donot requirethenumber2 ADF to be operative. e. At this point the inopetative numbet 2 ADF musteitherberemovedfrom the aircraft(FAR § 91.213(d)(3)(i))or deactivated (FAR 8 91.213(d)(3)(iij).Thepersonremoving or deactivating the number2 ADF mustplacard it inoperativein the appropriatelocation. (A pilot should consult maintenancepersonnel before deactivatingor having maintenance. personnelremoveanyitem of equipment.) I Chap 2 Par13 7 AC 919 67 . 6/28/91 During the preflight inspection, the pilot recognizes inoperative instruments or equipment. & IS the equipment required by the aircraft's equipment list or the kinds of If YES, the aircraft is equipment list? (FAR + § 91.213(d)(2)(ii).) unairworthy and maintenance is required. J+ If NO, is the equipment required by the VFR-day type certificate requirements If YES, the aircraft is . prescribed in the airworthiness certification regulations? (FAR § 91213(d)(2) (ii).) See appendix 1 of this AC. + unairworthy and maintenance is required. If NO, is the equipment required by AD? (FAR § 91.213(d) (2) (iv).) If YES, the aircraft is . + unairworthy and maintenance is required. *1 If NO, is the equipment required by FAR 55 91.205, 91.207, etc.? If YES, the (FAR aircraft is 5 91,213(d)(2)(iii).) + unairworthy and maintenance is required. 4 If NO, the inoperative equipment must be removed from the aircraft (FAR § 91.213(d) (3)(i)) or deactivated (FAR § 91.213(d) (3) (ii)) and placarded as At this point the pilot shall make a final determination to confirm that the inoperative instrument/equipment does not constitute a hazard under the anticipated operational conditions before release for departure. a Figure 2. Pilot Decision Sequence When Operating Without An MEL- 8 Chap 2 - 6/28/91 AC 91- 67 j? Finally, the pilot should decide whether the inoperative number 2 ADF creates a hazard for the anticipated conditions of the flight, e.g., VFR-day. 15.48. RESERVED. Chap 2 Par 14 9 (and 10) AC 91-67 CHAPTER 3. OPERATING AIRCRAFT WtTH AN MEL ’ 19 APPLICABILITY. This chapter p&ides guidance for operators who want to conductflight operationsunder the provisions of an MEL. 20 APPLYING FOR MEL APPROVAL. FAA has only one procedurefor the issuanceof FAR Part 91 MEL’s, and it is the procedurethe FSDO will follow for FAR Part 91 MEL authorizations. The operator who wishes to conduct operations with an MEL must contact the FSDO which has jurisdiction over the geographicarea where the aircraft is basedand make an appointment a. FAR Part 91 operators who received MEL authomtion under the approvalsystemin place before July 5, 1990, have letters of authorization that will expire. Those operators may continue to operate as usual; however, at least 30 days before the letter is due to expire, the operatorshould contactthe issuing FSDO so that the FSDO can issue a new LOA. b. For FAR Part 91 operators seeking MEL authorization under the current approval system, the FSDO will assigna Flight Standards inspector to advise the applicant about FAR requirementspertinentto using an MEL. During the initial appointment,the applicant will likely be dealing with a team of inspectorsfrom the operations,airworthiness,and avionics units. c. The inspector will provide the applicant with a copy of the appropriateMMEL, a copy of this AC, and a copy of the preambleto the MMEL. If the operator has installed items of equipment that are not on the MMEL, the operator must request that the MMEL be amendedto include those items of equipment. This requestis made to the FSDO. d. The operator and the team of inspectors discuss the requirements for the proceduresdocument. When FSDO personnel believes that the operator understands the requirements for operating with an MEL, the FSDO issuesthe operatorthe LOA (appendix4). (1) The LOA containsthe legal name of the operator and the addressof the operator’s DrinCiDalbase Of ODeratiOnS. (2) Both the FAA inspector and the operator (Or the operator’s bona fide representative)sign the LOA. e* If, afier meeting with FSDO personnel and discussing MEL operational considerations, an inspector believes that the applicant doesnot have a good understandingof the requirements,the FSDO will not issue the LOA. If the LOA is still desired, the applicant should obtain the necessaryunderstandingof the requirements from appropriate sources. After obtaining and understandingthe requirements, the applicant can again request the LOA from the FSDO. The applicant could also elect to operateunder FAR 0 91.213(d). f. Once the FSDO issues the LOA, the applicant is then responsible for developing a documentthat contains 0 and M proceduresfor disabling or rendering inoperative items of equipmentin accordancewith FAR Parts43,91, or 145 (if a repair station accomplishes the activity), as appropriate. No further FAA approvalis necessary,and the operatorcanbegin flight operations.The MNIEL, preamble, LOA, and the proceduresdocumentarenow considered an MEL. I Chap 3 . Par 19 11 AC 91- 67 .6/ 28/91 (1) The operatorshoulddevelopthe 0 andM proceduresusingguidancecontainedin the manufactuier’saircraftnight and/ormainte- nancemanuals,themanufacturer’s recommenda- tions, engineeringspecifications,and other appropriatesources.The operatormay consult FSDO airworthinessinspectorsfor adviceor clarification,but the operatoris responsible for preparingthe document (2) The operator must consider the following when preparing the procedures document: (i) The operator’s procedures documentmaybe morerestrictivethanthe MMEL either by the applicant’schoice or becauseof AD’s or operatingrules. The owrator’sprocedures documentmaynot be= restrictivethanthe MMEL. (ii) Thetitle pageof theprocedures documentmustcontainthe followingstatement: This MEL is applicableto FAR Part91 operationsonly andmay not beusedfor operations conducted under FAR Parts121,125,129,or 135. (iii) ‘Ihe operatormustusetheATA numbering system for equipment and instruments, as is used in all MMEL’s’ (appendix1). The operatormust usethe ATA numberingsystemin sequence whendescribing 0 andM procedures, includingthe numbersfor equipmentinstalled in the aircraft. When equipmentis not installedin a specificaircraft, the applicantneednot develop0 andM proce- duresfor thoseitemsof equipment. (iv) Operatorsmust ensurethat the procedures documentliststheitemsof equipment that areactuallyinstalledonthe specificaircraft. This providesguidanceto a pilot as to which items of equipmentmay be inoperativefor a particularoperation. (v) Equipmentspecificallyrequired by theairworthiness ruleunderwhichtheaircraft is typecertificated,equipmentrequiredby AD, andequipmentrequiredfor specificoperations underFAR 8 91.213(b)(l),(2) and(3) must be operative.It is’importantto notethat all items relatedto the airworthinessof the aircraft that are not included on the MMEL must be operative. (vi) TheA, B, C, andD codes,listed in column 1 of the MMEL, apply only to operations conducted underFAR Parts121,125, 129,and135. (vii) Where the MMEL states “as requiredby FAR,” ‘the proceduresdocument shouldlist the particular FAR by part and section,or describethe actualFAR requirement applicable to the operator’sparticularoperation. Forexample,wheretheFAR requiresa clockfor IFR flight, the operator’sprocedures document shouldsay,“May be inoperativefor VFR.” (viii) The proceduresdocumentmust specify suitable limitations in the form of placards, maintenance procedures, crewoperating procedures,and other restrictionsto ensurean acceptable levelof safety. (ix) The proceduresdocumentmust specifythoseconditionsunderwhich an item may be inoperative. The remarksmust also identify requiredmaintenanceor operational t&S. The symbol “0” or ‘%I”, placed in column4 of the MMEL (appendixl), indicates that an 0 or M procedureis applicableto that item. Indicatingthe 0 andM procedures in the proceduresdocumentprovidesflightcrewsand ground support personnel with a single proceduralreferencedocument. 12 chap-3 Par 20 6/28/91 AC9&67 (x) If the 0 andM procedures are alreadystatedin the AFM, the maintenance manual,or otheravailable FAA-approved source, the operatorneedsto showonly the reference; e.g.,0: AFM, pp. 3-8 through3-10,para.347. If the operatorusesthis referenceformatin the procedures document, thereferenced sourcemust be readily availableto the ground support personnel,anda copy of the referencessource must be carriedin the aircraft andbe readily availableto the flightcrew. (xi) If the 0 andM procedures are not in the AFM, .the maintenance manual,or otheravailableFAA-approvedsource,or if the operatorwishesto useadifferentprocedure, then the operatormust list the procedurein the procedures document. (xii) Theprocedures documentmay not conflict with the AEM limitations, emergency procedures, AD’s, or the AMM. (3) An operatormay begin operations beforecompletionof the proceduresdocument. If theoperatorhasnot yetdeveloped a procedure for an item,that itemmustbe operative.When an instrumentor item of equipmentbecomes inoperative,the operatormustfollow the pruce- dureindicatedin theprocedures documentor the operatorcould be in noncompliance with the FAR. 21. MEL AUTHORIZATION. The MEL appliesonlyto a particularaircraftmake,model, serialnumber,andregistrationnumber.Also,it appliesonly to the operatorwho receivedthe authorization. a. When more than one operator has operational control of a specm aircrqft, dl operatorsmust meet with inspectorsfrom the issuing FSDO to discussMEL operational considerations, asdescribed in paragraph 20.The FSDOmayfind it appropriate to list all operators on the LOA. Each operatormust sign the “Statementof Operator”‘onthe LOA. b. The FSDO may issue operators who use several aircraft of the sametype a single LOA that lists each aircraft by serial and registrationnumbers. The FSDO will issue separate lettersfor differenttypesof aircraft. (1) When operatorsadd or delete aircraftof the sametype from their fleet, they must notify the FSDOhavingoversightwithin 10 calendardays following the change. The FSW will reissuethe LOA containingthe new information. Again,both the operatorandthe inspectormustsignthenew LOA. (2) The operatormust surrenderthe previousletter uponreissuanceof a new one. ThekFSDO shouldplacethe old letter in the operator’sfile. c. At any time after operating with a FAR Part 91 MEL, an operatormay electto operateunderFAR 0 91.213(d). The operator must,surrenderthe LOA to the issuingFSDO and must conform to all provisionsof FAR 8 91.213(d)duringoperations. 22.. REVISIONS. The operatormay have to revisethe proceduresdocumentunder several conditions.The AEG may authorizean FOEB to revisethe MMEL, the operatormay add equipment,. or the FOEB may developa type- specificMMEL for a single-engine aircraft. a. When the FOEB revises an MMEL, the FAA automated,nationalMMEL database notifiesoperatorswho haveMEL authorizations by mail. The operatoris then responsiblefor Chap 3 Par 20 13 AC 910 67 6/28/g 1 obtaining a copy of the revisedMMEL from the FSDO that issued the authorization. Within 30 .calendardays of notification, the operator must replace the supersededrevision of the MMEL with the current revision and add or delete procedures to the procedures document, as applicable. b. Within 10 calendardaysof installing new equipmentnot on the MMEL, the operator may requestthat the MMEL be amended. . (1) If the items of newly installed equipment are not instruments or equipment specifically required by the airworthiness rule under which the aircraft is type certificated, an AD, or for specific operations under FAR 0 91.213(b)(l), (2) or (3); and exceed what is listed on the h4MEL; and the FSDO has determinedthat the equipmenthasnot previously been denied for inclusion in an MMEL, the operatormay petition the FOEB for inclusion of the newly installed equipment in the MMEL. All petitions, with appropriate supporting information, will be forwarded by the FSDO to the appropriateFOEB. Then the operator may add the equipmenttemporarily to the MMEL and develop appropriate0 and M proceduresfor the equipment. The operatormay then operatewith the equipmentinoperativepending a decisionby the FOEB on the operator’s request for an MMEL revision to include the equipment. (2) If the FOEB haspreviously deniedthe inclusion of the equipment, or if the equipment is safety related, or if the equipment was previously installed or is “factory original,” the operatormay still petition the FOEB through the FSDO for inclusion of the equipment in the h4NIEL. However, the operator may not gain relief for the equipmentby addingthe equipment to the MNIEL temporarily and addingprocedures to the proceduresdocumentpending the FOEB’s decision. The equipment must be operative before operatingthe aircraft C. Although FAA has developeda gene& MMEL for operators of single-engine aircraft, an FOEB may decide that a complex, turbine-poweredsingle-engineaircraft requiresa type-specific MMEL. For example, an FOEB has developed a type-specific MMEL for the Cessna208, Caravan. (1) When an FOEB develops a specific MMEL for a single-engineaircraft, the FAA will notify all holders of MEL’s for that aircraft under the generic MMEL that the specific MMEL is available. (2) Within 30 calendar days of notification, the operatormust obtain the MMEL from the FSDO and begin the processfor a new LOA. Only by issuing a new LOA will the FSDO be assuredthat the operator has and is using the type-specific MMEL. (3) Oncethe FSDO issuesthe new LOA, the operator must develop, within an additional 30 calendar days, a new proceduresdocument that conforms to the requirementsof the type- ’ specific MhEL. The operator will find that most of the procedures that were acceptable under the genericMMEL will transferto the new proceduresdocument. If equipment’ becomes inoperative while the operator is developing the new proceduresdocument,the operatormay still use the previous procedures,as appropriate. 23. CONDUCTING OPERATIONS WITH AN MEL. In addition to carrying the documentsthat comprise the MEL onboard the aircraft, the operator must have onboard any technical manuals needed to accomplish 0 and M procedures.Figure 3 illustrates the sequence of events involved in applying the MEL to inoperative equipment. 14 Chap 3 Par 22 . 1 6f 28/91 AC 91-67 a. Inoperative Items Before Flight. During a preflight inspection for a VFR-day flight, the pilot discoversa navigation light is inoperative. (1) The pilot checksthe aircraft’s MEL to determine under what, if any, flight conditions the aircraft could be operated without operator navigation lights. The MEL indicates that the aircraft may be operatedduring daylight hours without operablenavigation lights. (2) The pilot checksthe proceduresdocu- ment and deactivatesthe navigation lights by pulling the correct circuit breaker and having it collared by an appropriatelycertificated person. (3) The pilot places a placard which indicates that the lights are inoperative near the navigation light control. (4) The pilot examinesthe conditions of the proposedflight and determinesthat the flight can be conducted safely without navigation lights. ’ b. In-Flight Failures. An MEL appliesonly to the takeoff of an aircraft with inoperative instrumentsor equipment. The pilot’s operating handbook or the AFM indicate procedures.to follow for instrument or equipment failure in flight. The pilot in command (PIG) should handle the in-flight failure in accordancewith those procedures. As soon as possible after landing safely, the PIC must enter a notation of the inoperative equipment in the aircraft’s maintenancerecords, logbooks, or discrepancy record. Before the next takeoff, the pilot must apply the MEL to inoperative equipment as per the proceduresin paragrapha. above. An MEL allows the PIC to defer maintenanceon many items under the following conditions: (1) The aircraft is in a condition for safe flight, and (2) For the inoperativeitem, the pilot has followed the specific conditions,limitations, and proceduresin the proceduresdocument. c. Deactivation or Removal and Placarding. See Chapter 1, paragraph7. d. CorrectingMEL Inoperative Items. The MEL permits operationswith inoperative items of equipment for the minimum period of time necessaryuntil the equipment is repaired. It is important that operatorshave repairsdone at the earliestopportunity in order to return the aircraft to its designlevel of safety and reliability. In all cases,inoperativeequipmentmust be repairedor the maintenancedeferred at the aircraft’s next requiredinspection (FAR 8 91.405(c)). (1) Operatorsshall establishprocedures to correct those inoperative items authorized within specified time requirements. (2) Owners of aircraft operated under FAR Part 91 may opt to use one of severaltypes of airworthiness inspection systems,.depending upon the operator’s use of the aircraft. Therefore,the time betweenrequiredinspections or inspection segmentswill vary. (3) Items of inoperative equipment, authorizedby the MEL to be inoperative, must be inspected or repaired by qualified maintenancepersonnel,or maintenancedeferred, at the next lOO-hour, annual, progressive, or unscheduled inspection. However, if FAR 6 91.213 requires that an item be repaired, the item cannot be deferred. e. RecordkeepingRequirements. A record of inoperative equipment must remain in the aircraft so pilots will be aware of all dis- crepancies. Chap 3 Par 23 15 AC 910 67 During the preflight inspection, the pilot discovers inoperative instrument or equipment. If yes, The pilot checks aircraft's MEL. If the inoperative equipment is not included in MEL but is required by type certificate, AD, or special conditions: L If no, + + The aircraft is not airworthy; repair before flight. Pilot performs or has a qualified person perform the appropriate 0 or M deactivation or removal procedure. The pilot or maintenance personnel placard the inoperative equipment. The pilot can take off after confirming that the inoperative equipment does not present hazards to the conditions of flight. Figure 3. Pilot Decision SequenceWhen Operating With An MEL 16 Chap 3 : 6/28/91 AC 919 67 . (1) Since some operators do not carry aircraft logbooks in the aircraft, a discrepancy record or log (figure 4) is a good alternative. When an operator usesthis type of discrepancy log in lieu of the aircraft’s maintenancerecords, the operator must retain the log as a part of the aircraft’s recordsas per FAR 0 91.417(b). \ (2) If the operator elects to use the aircraft maintenancerecord to log inoperative items, that portion of the recordmust be carried onboard the aircraft during all operations. the sameaircraft under different regulations. For example, a Cessna340 could be operatedby an approved school under FAR Part 91, by an air carrier under FAR Parts 135, and by a rental pilot under FAR Part 91. FAA will not approve multiple MEL’s, which would create pilot confusion, with discrepancy lists and sets of proceduresfor the sameaircraft. In the example, the aircraft would operate under the FAR Part 135 MEL, including the A, B, C, and D codes, with approval from the FSDO for other usersto conduct operationsunder other regulations. (3) Corrective actions and maintenance (2) FAA will grant operators approval proceduresshall be accomplishedand recorded for multiple users of an MEL under FAR Parts in accordancewith FAR @$43.9, 91.405, and 121, 125, 129, or 135 MEL, subject to the 91.417. following conditions: (4) Failure to record an inoperative item may result in an operationof the aircraft contrary to the FAR becausesubsequentpilots would not be able to determine the airworthiness of the aircraft. (i) The operatoris responsiblefor training alI personsin the MEL’s use, including the logging and clearing of discrepanciesand the use of the A, B, C, and D codes. J Aircraft Used in Multiple Operations. FAR 0 91.213(c) allows a person who has an approved MEL under FAR Parts 125, 129,or 135 to use that MEL for FAR Part’91 operations. The FAR Parts 121,125,129, or 135 h4EL must specify requirementsfor authorizedFAR Part 91 operators to comply with the more restrictive provisions establishedin the approvedMEAL. It is important that operators be capable of conducting operations in accordancewith the MEL. This includes, but is not limited to, accomplishing required maintenance in accordance with the certificate holder’s requirements. (ii) Operators shall maintain a complete, current list of all personstrained and authorizedto use the EL. (iii) The operator is responsiblefor determining the aircraft’s maintenancestatuson its return from a FAR Part 91 operation. The operatormust accomplish this before the aircraft is put back into FAR Parts 121,125,129, or 135 service. (1) The use of a leasedaircraft createsa situation whereseveralpersonsmay be operating (iv) FAA PrincipaI operations Inspectors shall verify that operators have establishedproceduresthat ensurean acceptable level of safety before authorizing personsto use the MEL under FAR Part 91. I Chap 3 Par 23 17 AC 910 67 6/28./g 1 . COMPANYor OPERATOR's NAME: LOG SHEET NUMBER: DATE: LOCATION: DISCREPANCY: C0RRECTIVE ACTION: ~~ ~~ ~~ Signature Certificate Number Date Figure 4. Sample Aircraft Equipment Discrepancy Record 18 Chap3 6/B/91 AC 9lij7 Appendix 1 APPENDIX 1. SAMPLE MMEL DOCUMENTS . FEDERAL AVIATION ADMINISTRATION MASTER MINIMUM EQUIPMENT LIST Page: Revision: Date: (AIRcRAFr TYPE) Preamble - PART 91 ONLY ‘3 This preamble is applicable to, and will be included in, Master Minimum Equipment Lists (MMEL) issued under the provisions of Section 91.213(a)(2). It is not applicable to MMELs issued under the provisions of Parts 121, 125, 129, and i35 of the FAR. Except as provided in Section 91.213(d), or under the provisions of an approved MNEL, all equipment installed on an aircraft in compliance with the airworthiness standards or operating rules must be operative. Experience has shown that with the various levels of redundancy designed into modern aircraft, operation of every system or component installed may not be necessary when the remaining equipment can provide an acceptable level of safety. An MMEL is developed by the FAA, aviation industry, with participation by the to improve aircraft utilization and thereby provide more convenient and economic air transportation for the public. The FAA-approved MMEL includes only those items of equipment which the Administrator finds may be inoperative and yet maintain an acceptable level of safety by appropriate conditions and limitations. The MMEL and FAA-issued letter of authorization are used as an MEL by an operator and permit operation of the aircraft with inoperative equipment. The MMEL includes all items of installed equipment that are permitted to be inoperative. Equipment required by the FAR, and L optional equipment in excess of FAR requirements, are included with appropriate conditions and limitations. For each listed item, the installed equipment configuration considered to be normal for the aircraft is specified. Items .of equipment. installed on aircraft (except for passenger convenience items : such as galley equipment and passenger entertainment devices), . such as nTCAS,Vt wind shear detection devices, and ground proximity warning systems (GPWS) that are in excess of what is required, and are not listed on the MMEL must be operational for dispatch unless MMEL relief is sought through the FSDO having 1 AC 919 67 Appendix 1 6/28/9.1 : APPENDIX 1. SAMPLE MMEL DOCUMENTS (Continued) jurisdiction for the operator; If MMEL relief is sought, the operator must notify the FSDO who will make a request of the FOEB to convene and consider adding the equipment to the MMEL. The operator may then dispatch.with the equipment disabled, or rendered inoperative, in accordance with all FAR. It is incumbent on the operator to endeavor to determine if 0 and/or M procedures for that equipment must be developed. If so, any procedures developed must comply with all FAR. Procedures developed to use the MMEL must not conflict'with either the Aircraft.Flight Manual Limitations, Emergency Procedures, or with Airworthiness Directives (AD), all of which take precedence over the MMEL and those procedures. Suitable conditions and limitations in the form of placards, maintenance procedures, crew operating procedures, and other restrictions, as necessary, are required to be accomplished by the operator-to ensure that an acceptable level of safety is maintained. Those procedures should be developed from guidance provided in the manufacturer's aircraft flight and/or maintenance manuals, manufacturer's recommendations, engineering specifications, and other appropriate sources. Procedures must not be contrary to any FAR. .Wherever the statement "Asrequired by FAR'! appears in the MMEL, the operator must either list the specific FAR by Part and Section and carry the FAR on board the aircraft, or specify the requirements and/or limitations to conduct the flight in accordance with the appropriate FAR. The MMEL is intended to permit operations with inoperative items of equipment for the minimum period of time necessary until repairs can be accomplished. It is important that repairs be accomplished at the earliest opportunity in order to return the aircraft to its design level of safety and reliability. Inoperative equipment in all cases must be repaired, or inspected and deferred, by' qualified maintenance personnel at the next required inspection Section 91.405(c). The repair intervals indicated by the Letters A, B, and C inserted adjacent to column 2 are NOT applicable to this MMEL. The MMEL provides for release of the aircraft for flight with inoperative equipment. When an i.tem of equipment is discovered to be inoperative, it is reported by making an entry in the aircraft maintenance records. The item is then either repaired, or deferred per the MMEL or other approved means acceptable to the Administrator, prior to further operation. In addition to the specific MMEL conditions and limitations, determination by 2 6/28/91 AC 91- 867 Appendix 1 APPENDIX 1. SAMPLE MMEL DOCUMENTS (Continued) the operator that the aircraft is in condition for safe operations under anticipated flight conditions must be'made for all items of inoperative equipment. When these requirements are met, the aircraft may be considered airworthy and returned to service. Operators are responsible for exercising the necessary -operational control to ensure that an acceptable level of safety is maintained. When operating with multiple inoperative items, the interrelationship between those items, and the effect on aircraft operation and crew workload, must be considered. Operators are expected to establish a controlled and sound repair program, including the parts, personnel, facilities, procedures, and schedules to ensure timely repair. . WHENUSING THE MMEL, COMPLIANCEWITH THE STATED INTENT OF THE PREAMBLE, DEFINITIONS, CONDITIONS, AND LIMITATIONS SPECIFIED IN THE MMEL IS REQUIRED. 3 AC 9% 67 Appendix 1 f;/m/91 APPENDIX 1. SAMPLE MMEL DOCUMENTS (Continued) FEDERAL AVIATION ADMINISTRATION Page: 1 MASTER MINIMUM EQUIPMENT LIST Revision: Date: TYPE AIRCRAFT Definitions 1. System Definitions. System numbers are basedon the ATA Specification Number 100 and items are numberedsequentially. a. “Item” (column 1) lists the equipment, system, component,or function in a column. b. “Number Installed” (column 2) is the number of items normally installed in the aircraft. This number representsthe aircraft configuration considered in. developing this MMEL. Should the number be a variable (e.g., passengercabin items), a number is not required. c. “Number Required for Dispatch” (column 3) is the minimum number (quantity) of items required for operation provided the conditions specified in column 4 are met. d. “Remarks or Exceptions” (column 4) in this column include a statementeitherprohibiting or permitting operationwith a specific numberof items inoperative, provisos (conditions and limitations) for such operation, and appropriate notes. e. A vertical bar (changebar) in the margin indicates a change, addition, or deletion in the adjacenttext for the currentrevision of that page only. The change bar is dropped at the next revision of that page. 2. “Airplane Flight Manual or Rotorcraft Flight Manual” (AFM/RFM) is the document required for type certification and approved by the responsible FAA ACO. The FAA approved AFM/RFM for the specific aircraft is listed on the applicableTCDS. 3. “As required by FAR” means that the listed item is subject to certain provisions (restrictive or permissive) expressedin the FAR operating rules. The number of items requiredby the FAR must be operative. Items installed that are in excess of the FAR requirements may be permitted to be inoperative if not otherwise requiredby the MMEL. 4. The asterisk “*” symbol in column 4 indicates the listed item, if inoperative, must be placarded to inform and remind the crewmembersand maintenancepersonnelof the equipment condition. Note: To the extent practical, placards should be located adjacent to the control or indicator for the item affected; however, unless otherwise specified, placard wording and location is determinedby the operator. 5. The dash “-” symbol in column 2 and/or column 3 indicates a variable number (quantity) of the item(s) installed. 4 6/28/91 AC 910 a67 Appendix 1 APPENDIX 1. SAMPLE -L DOCUMENTS (Continued) 6. ‘Deleted” in the remarks column after a sequence item indicates that the item was previously listed but is now required to be operative if installed in the aircraft. 7. “ER” refers to extendedrange operationsof a two-engine airplane which has a type design approval for ER operations and complies with the provisions of Advisory Circular 120-42A. 8. “FederalAviation Regulations”(FAR) arethe applicable portions of the Federal Aviation Act and Federal Aviation Regulations. 9. “Flight Day” refersto a 24 hour period (from midnight to midnight) either Universal Coordinated Time (UCT) or local time, as establishedby the operator,during which at least one flight is initiated for the affected aircraft. .* 10. “Icing Conditions” indicate an atmospheric environment causing ice to form on the aircraft or in the engine(s). 11. Alphabetical symbol in column 4 indicates a proviso (condition or limitation) for operation with the listed item inoperative. 12. “Inoperative” indicates a system and/or componentmalfunction that doesnot accomplish its intended purpose and/or is not consistently functioning normally within its approved operatinglimit(s) or tolerance(s). 13. “Notes:” in column 4 provide additional information for crewmember or maintenance consideration. Notes are used to identify applicable material intended to. assist with compliance, not to relieve the operator of the responsibiity for compliance. Notes are not a part of the provisos. 14. Inoperative components of an inoperative system are componentsdirectly associatedwith and having no other function thanto supportthat system. (Warning/caution systems associated with the inoperative system must be operative unless relief is specifically authorized per the =.I 15. “(M)” symbol indicates a requirementfor a specific maintenanceprocedure which must be accomplishedprior to operation with the listed item inoperative. Normally theseproceduresare accomplished by maintenance personnel; however, other personnel may be qualified and authorized to perform certain functions. Proceduresrequiring specialized knowledge or skill, or requiring the use of tools or test equipment should be accomplished by maintenance personnel. The satisfactory accomplishmentof all maintenanceprocedures, regardless of who performs them, is the responsibility of the operator. Appropriate proceduresare required to be published as part of the operator’smanual. 16. “(0)” symbol indicates a requirement for a specific operations procedure which must be accomplished in planning for and/or operating with the listed item inoperative. Normally these proceduresare accomplish?dby the flight crew; however, other personnelmay be qualified and authorized to perform certain functions. The operator is responsible for the satisfactory accomplishmentof all procedures,regardlessof AC 91-67 Appendix 1 APPENDIX 1. SAMPLE MMEL DOCUMENTS (Continued) who performs them. Appropriate proceduresare required to be published as a part of the operator’smanual. NOTE: The (M) and (0) symbols require the operator to develop proceduresfor the removal, disabling, or rendering inoperative of items of equipment, in accordancewith FAR Part 91, Part 145, or Part 43, as appropriate. 17. “Deactivated”and “Secured”suggestthat the specified component is in an acceptable condition for safe flight. The operator will provide an acceptablemethod of securing or deactivating. 18. “Visual Flight Rules” (VFR) are as defined in FAR Part 91. This precludes a pilot from filing an Instrument Flight Rules (IFR) flight Plan. 19. “Visual Meteorological Conditions” (VMC) indicate an atmosphericenvironmentthat allows a flight to proceed under the visual flight rules. 20. Three days are 3 consecutivecalendardays (72 hours), excluding the day the mdlfunction was recorded in the aircraft maintenance record/logbook.For example,if it were recorded at 10 a.m. on January26th, the 3&day interval would begin at midnight the 26th and end at midnight the 29th. 21. CategoryC. Items in this categoryshall be repaired within 10 consecutive calendar days (240 hours), excluding the day the malfunction was recorded in the aircraft maintenance record/logbook. For example,if it were recorded at 10 a.m. on January26th the lo-day interval would begin at midnight the 26th and end at midnight February 5th. The letter designators are insertedadjacentto column 2. 22. Engine Indicating Crew Alerting System (EICAS), Electronic Centralized Aircraft Monitoring System (ECAM) or similar systems that provide electronic messages refer to a system capable of providing different priority levels of systems information messages (e.g., Warning, Caution, Advisory Status and Maintenance). Any airplane discrepancy messagethat affectsdispatchability will normally be at statusmessagelevel (e.g.,Advisory Status) or higher. 23. The threeasterisk“***/cl(symbol in column 1 indicates an item which is not required by regulationbut which may have been installed on some models of aircraft coveredby this MMEL. It shouldbe noted that neither this definition nor . the useof this symbol provide authority to install or remove an item from an aircraft. 6 6/28/91 -~-~ AC 919 67 Appendix 2 APPENDIX 2. SAMPLE LETIER OF AUTHORIZATION Flight Standards District Office Portland-Hillsboro Airport 3355 NE Cornell Road Hillsboro, OR 97124 July 25,199l Mr. John Dough, President John Dough Enterprises Hangar 9, Suite 203 Portland-HiUsboro Airport Hillsboro, OR 97124 Dear Mr. Dough: This letter is issued under the provisions of FAR 3 91213(a)(2) of the Federal Aviation Regulations (FAR) and authorizes John Dough Enterprises only to operate Cessna Citation 500, N81149, Serial No. 12345, under the Master Minimum Equipment List (MMEL), using it as a Minimum Equipment List (MEL). This letter of authorization and the MMEL constitute a Supplemental Type Certificate for the aircraft and must be carried on board the aircraft as prescribed by FAR 0 91.213(a)(2). Operations must be conducted in accordance with the MMEL. Operations and maintenance (0 and M) procedures for the accomplishment of rendering items of equipment inoperative must be developed by the operator. Those procedures should be developed fkom guidance provided in the manuf&cturer’s aircraft flight and/or maintenance manuals, manufacturer’s recommendations, engineering specifications, and other appropriate sources. Such operations or maintenance procedures must be accomplished in accordance with the provisions and requirements of FAR Part 91, Part 145, or Part 43. . A means of recording discrepancies and corrective actions must be in the aircraft at all times and available to the pilot in command. Failure to perform 0 and M procedures in accordance with Part 91, Part 145, or Part 43 as appropriate, or to comply with the provisions of the MMEL, preamble, 0 and M procedures and other related documents, is contrary to FAR and invalidates this letter. All MMEL items that contain the statement “as required by FAR” must either state the FAR by part and section (e.g., 91.205) with the appropriate FAR carried aboard the aircraft, or the operational requirements/limitations required for dispatch must be clearly stated. When the MMEL is revised by the Flight Operations Evaluation Board (FOEB), John Dough Enterprises will be notified by post card of the revision. John Dough Enterprises must then obtain a copy of the revision from this Flight Standards Disctirc Office (FSDO), or the FSDO having jurisdiction, and incorporate any changes as soon as practicable including 0 and M procedures as required. John Dough Enterprises must develop 0 and M procedures that correspond with those listed in the MMEL. John Dough Enterpks must also list the “as required by FAR” by specific FAR part and section, or state the operational requirements/limitations for aircraft dispatch. These items must be contained in a procxxiures document that is -1 AC 9% 67 Appendix 2 6/28,!91 APPENDIX 2. SAMPLE LETIER OF AUTHORIZATION (Continued) separate from the MMEL and must accompany the MMEL, preamble, and letter of authorization (LO). They must all be onboard the aircraft anytime it is operated. Equipment installed on this aircraft (other than passenger convenience items such as galley equipment and passenger entertainment devices) that are in excess of what is required, and are not listed on the MMEL, must be operational for dispatch unless a request is made to this FSDO (or subsequent FSDO that has jurisdiction) to seek relief fi-om the FOEB, through a revision to the MMEL, at the earliest opportunity for the FOEB to convene. If h4MEL relief is sought, this FSDO (or subsequent FSDO) must be notified within 10 calendar days (including weekends and holidays) following installation. The operator may then conduct operations with the equipment inoperative for dispatch provided it is disabled, or rendered inoperative, in accordance with all the FAR. It is the responsibility of John Dough Enterprises to determine if 0 and/or M procedures must be developed for disabling, or rendering inoperative, the equipment. If so, any procedures that are developed must comply with all FAR. If MMEL relief is not sought, the FSDO need not be notified following installation of the equipment. Should John Dough Enterprises relocate its principal base of operations (address), they must notify in writing both this FSDO, and the new FSDO that will have jurisdiction, within 10 calendar days following relocation. This letter is issued without an expiration date and will remain valid until voluntarily surrendered by John Dough Enterprises, John Dough Enterprises ceases to be the operator of N81149, or it is suspended or revoked for cause by the Federal Aviation Administration (FAA). In any case, should it become invalid, it must be returned to this office or he FSDO having jurisdiction within 10 calendar days from the date it becomes invalid Sincerely, Principal Operations Inspector STATEMENT OF OPERATOR . As evidenced by my signature below, I certify that John Dough Enterprises will operate Cessna 500, N81149, in f compliance with the authorizations, provisions, and limitations incumbent with the utilization of this LOA issued in accordance with FAR 8 91.213(a)(2). A copy of this letter will be made a part of the MEL file maintained by this FSDO of John Dough Enterprises. Signature Title Date 2 _. 6128191 AC 9X-67 Appendix 3 APPENDIX 3. SAMPLE TITLE PAGE JOHNDOUGHENTERPRISES MINIMUM EQUIPMENTLIST PROCEDURES DOCUMENT Cessna500 N81149 Thisminimumequipmentlist is applicable to FAR Part91 operationsonly andmaynot beusedfor operations conductedunderFAR Parts121,125,or 135 -1 6/28/91 AC 91967 Appendix 4 APPENDIX 4. COMMONLY ASKED OUESTIONS ABOUT MEL’S 1. Can the operator make changes to an MEL document without changeshaving been made to the MMEL? How do they get approved? . ...* To make changesto the MEL, the operatormust write to the FSDO exercisingjurisdiction over its operationthat it wishesto havethe MEL revised. This would apply to newly installed equipment that is not required by type certification rules, operating rules, and/or is in excess of what is required and is not listed on the MMEL. The FSDO will contact the FOEB and requestthe equipment be consideredat the next meeting of the FOEB. During the interim, the aircraft may be operated with the items of equipment inoperative provided the operatorhas developed 0 and M procedures(as applicable)that comply with all the FAR. 2. What happens if my aircraft is destroyed in an accident? Do I need to return the MEL and Letter of Authorization (LOA) to the issuing FSDb? If the MEL and LOA survive in a readableform, they must be surrenderedto the issuing FSDO, or the FSDO having jurisdiction for the operator, with an official notification of the aircraft’s destruction in an accident. A National Transportation Safety Board’s indication of the aircraft’s destructionis sufficient evidenceif the aircraft was destroyedoutsideof the appropriate FSDO’s jurisdiction. 3. What if an FAA inspector asks to seemy MEL, procedures document, and LOA? Because the FAR requires that the MEL, procedures document, and LOA be carried onboard the aircraft, the operator must show an FAA inspector,or other authorizedrepresentative of the Administrator, the documents when requested. 4. ,What happens when the original MEL is no bnger appropriate? This would dependon the conditions that caused the MEL to become inappropriate,since MEL’s must be revised when MMEL’s am revised. 5. Does the FAA perform any type of surveillance after approval of an MEL? If so, how often? FAA inspectors do not specifically survey or inspect operatorsusing an MEL. However, as part of a ramp inspection, inspectorswill check to determine if an aircraft is operating with an MEL or under the provisions of FAR 5 91.213(d). 6. What happens to the MEL if the aircrafi is sold? The MEL and LOA are not transferrable. The MEL and LOA must be surrendered to the FSDO exercising jurisdiction. The new owner must decide if he/she wants to operate with an MEL or under the provisions of FAR 5 91.213(d). If the owner elects to operatewith an MEL, he/s&e must apply for one at the appropriateFSDO as describedin this AC. AC 91-67 Appeiidix 4 6/28/91 APPENDIX4. COMM[ONLYASKEDQUESTIONSABOUTMEL’S (Continued) 7. Can an operator request withdrawal of an lO.How do I transfer my MEL and LOA if I approved MEL and elect to operate under move out of the jurisdiction of the issuing FAR 6 91.213(d)? FSDO? Bothprovisionsof FAR 5 91.213offer reliefto operators. Operatorswill find more relief operatingwith an MEL. However,an operator cansurrenderanMEL andLOA by submitting themto theissuingFSDO with aletterindicating that the operatorno longerwishesto operate with anMEL. As of thedatetheMEL andLOA weresurrendered, the aircraftmust be operated underFAR 0 91.213(d),providedit canmeetthe requirements of FAR 6 91.213(d).If theFSDO determines it cannot,it mustcontinueto operate undertheMEL. 8. Can the applicant operate the aircraft under FAR 0 91.213(d) while waiting for an approval to a proposed MEL? Undertheregulation,theoperatorwouldhaveno choiceexceptto operateunderFAR8 91.213(d), to whateverextenthe/shecan,until authorization to operateunderan MEL is receivedand the LOA issued. 9. If an MEL LOA is issued in one FSDO’s jurisdiction, do I have to have it reissued if I’m operating in another area of jurisdiction? No. The FAA considersanMEL LOA issuedby one FSDO as sufficientfor use in any other FSDO’sjurisdiction. For a FARPart91 operation,the operatormust notify boththe FSDOexercisingoversight,and the FSDOthat will exerciseoversight,of the new locationof the aircraftwithin 10 calendar days following the Rlocation. The previous FSDOwill thenforwardtheoperator’sMEL file to the acquiringFSDO through the FAA’s regionaloffice havingjurisdictionfor the new location. The acquiringFSDO will enter the new location information into the national MMEL databasefor revisionandupdate. 11. There are a number of items on the Beech58P Baron MMEL that need clarifying. For example, the MMEL states that you can take off with one fuel quantity indicator inoperative provided that an approved reliable means is established to determine there is enough fuel required by regulation. What is an example of @*anapproved means”? , The pilot canvisuallycheckthe fuel and,if it werefull, knowhow muchfuel wasonboardfor theflight. A dipstickcalibratedfor that aircraft or any other meansthat providesa positive measurement wouldbe acceptable. 12. Does an operator have to use the sample discrepancy record provided in this AC? The sampleis the preferredmethod,but the operatormaydeviseoneof their own choosing; however,it mustcontainat leasttheinformation indicatedin the samplein this AC. . 2 :’ . . 6/28/91 AC 91-67 Appendix 4 APPENDIX 4. COMMONLY ASKED QUESTIONS ABOUT MEL’S (Continued) 13. If I hold a Part 125 Deviation, may I receive authorization to conduct operations under a Part 91 MEL? If an operatorholds does not hold Certificate, he/she -. conduct operations FAR Part 91 MEL. a Deviation to Part 125 and a Part 125 Operating may be issued a LOA to under the provisions of a ,a‘..: 14. If I currently have an approved &IEL issued under Part 91, how does this new procedure affect me and my operation under that MEL? You may continue to operateunder your present LOA until it expiresat which time you would be reissuedthe new letter. You could also choose to surrender your current letter, prior to its s. ‘\ expiration date, in exchange for a new letter i... along with the MJklEL. Either way, you may.’ continue to use your MEL documentcontaining 0 and M proceduresas the proceduresdocument referencedin this AC. 15. Since I no longer have to submit my 0 and M procedures to the FSDO for approval prior to receiving the LOA, can I accomplish the activity by mail? No It is important that Aviation Safety Inspectors (ASI) from the issuing FSDO meet with you (or a bonafide representativeof you or your organization/company,etc. having signature authority) to discussMEL operatingprocedures prior to issuanceof the LOA. This is necessary to ascertainyour ability to operatein accordance with the provisions of an l44EL. All mL LOA, therefore,can only be issued in person. 16. Who is a bonafide representative? It can be anyone with signature authority; ie., the chief pilot, director of operations,director of maintenance,or other company officer. In the case where none of the above are applicable, a letter on company letterhead introducing the individual as a bona fide representativeand signedby a company officer may suffice. 17. Must I make my request for a meeting with the FSDO inspectors in writing? There is no specifiedrequirementthat the request be madein writing, however, it is the prerogative of the FSDO to make such azquest at their option. 18. Must AS1 from all three disciplines; operations, maintenance, and avionics, be available for the meeting to discuss MEL operating procedures? It is preferred that all three disciplines be represented;however, it is not necessaryif due to work constraints they will not be available within a reasonable period of time. It is important that an operations inspector be involved in the discussion since the mL is an operatingdocument. 3.